Could not open connection to the host on port 25 exchange 2010
We have exchange hosted in the company with the public IP from our ISP, now we are facing the bounce back emails from some domains
Could not be delivered because of
Server refused mail at END OF DATA - 554 5.7.1 The message from (with the subject of (RE: Schon Properties - Final Discounted Offer - Golden System.)
matches a profile the Internet community may consider spam. Please revise your message before resending.
only few domains bounce back the emails.
aslo i cannot telnet our mail server.
so what could be the issue.
please help someone to solve this issue.
Fuad
Looks like some domains you are sending to have implemented spam filters and they consider your email content to be spam. You'll need to contact them and have them set up any whitelists for your domain as needed.
http://www.faq.nuvotera.com/error%E2%80%845-7-1-the-message-from-with-the-subject-of%E2%80%84-matches-a-profile-the-internet/
As far as telnet goes make sure you are using port 25 and your static IP. Firewalls sometimes block this internally.
-- Al
Similar Messages
-
Could not open connection to the host, on port 23: Connect failed
Can anyone please help with this telnet problem on CISCO 877 ADSL Router
I am trying to telnet into my ISP Router remotely using public IP which has been dynamically assigned to the router by the ISP.
I can Ping the Router and I can also go out to the internet on that router but, I can not telnet into that router from Inside the Network nor Outside the Network. There are no Firewalls involved.
I have tried to clear the config and reconfigure it again, it does not help, I have also applied same config on another CISCO 877 ADSL Router it still does not work.
ERROR i get on the Command Prompt: Could not open connection to the host, on port 23: Connect failed
I have shown some of the Show Run out put below if that helps,
ip nat inside source list 1 interface Dialer0 overload
access-list 1 permit x.x.x.x 0.0.0.7
dialer-list 1 protocol ip permit
line vty 0 4
password 7 ***********
login
Manny Thanks
PunitFind Below the Requested Sh run outputs
ADSL-ROUTER1#sh run | beg line vty
line vty 0 4
password 7 ***********
login
scheduler max-task-time 5000
end
I have removed the IP for security reasons
ADSL-ROUTER1#sh ip route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
x.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
S x.x.x.x/29 is directly connected, Vlan1
C x.x.x.x/32 is directly connected, Dialer0
x.0.0.0/32 is subnetted, 1 subnets
C x.x.x.x is directly connected, Dialer0
S* 0.0.0.0/0 is directly connected, Dialer0
I also keep getting the message below on the console done know if this is part of the problem
Mar 13 07:17:32.213: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Vlan1: the fragment table h
as reached its maximum threshold 16
Hope this output helps
Thanks -
Telent:could not open connection to the host on port 23 connect failed
Hi,
How to run commands of OEL5 host OS from windows XPP virtual machine(Vmware Player) on standalone desktop PC?
While runing the telnet command on windows XPP virtual machine it's gives error
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\Administrator>cd\
C:\>telnet 192.168.1.2
Connecting To 192.168.1.2...Could not open connection to the host, on port 23: Connect failed
C:\>
Thanks
Regard
GSMuser9230833 wrote:
Launcher means shortcut to execute any file which is inside folder in Linux.Launcher are created on desktop to execute by one click of mouse.You need to create a command file that contains the required instructions to run putty with whatever relevant command line switches in order to start the remote program/process on Linux.
For example, you have a trusted ssh connection (no password prompting) between your Windows account and the Linux vmware account. You need to execute command line +/home/vmware/bin/vmstart myVM+ on Linux.
Your command file in Window will look something as follows:
@echo off
"c:\program files\putty\pssh.exe" vmware@my-linux-server "/home/vmware/bin/vmstart myVM"Once you've create this command file (.cmd file extention), you can create a desktop shortcut for it and assign an icon to it.
However, first test the command file via an interactive console session to ensure it works. Also, I'm not sure you can script telnet using putty - but putty's ssh does support the standard ssh command line and one can execute programs/commands on the remote server in this fashion.
Setting up trusted ssh connections is also important as passwords is a weak security mechanism. It requires a secret to be used and coded into scripts/software that needs to be authenticated.
With ssh you generate a public/private key combination, and provide the public key as unique identifier for your o/s user and platform to a remote server (e.g. Linux). This now enables your platform and o/s user to be authenticated via the privatre/public key pair when your platform establishes a connection with the server.
In putty, generate a ssh key (RSA). Copy and paste the public key into the Linux server account's "+home/vmware/.ssh/authorized_keys+" file. Make sure that the +.ssh+ directory and key have user read/write permissions only. And that's it - no password needed by your account to ssh into the Linux server account. No secrets that need to be kept secret (and that can be stolen and used from any other platform to gain access). -
Could not open connection to the host, on port 4555: Connect failed
Hi,
I am new to apache James and javamail. I have installed the necessary things to do but i still cant run telnet localhost 4555.
What could be the cause of this?
Could there be anything I have missed?
pls help..
Thanks.: )Find Below the Requested Sh run outputs
ADSL-ROUTER1#sh run | beg line vty
line vty 0 4
password 7 ***********
login
scheduler max-task-time 5000
end
I have removed the IP for security reasons
ADSL-ROUTER1#sh ip route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
x.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
S x.x.x.x/29 is directly connected, Vlan1
C x.x.x.x/32 is directly connected, Dialer0
x.0.0.0/32 is subnetted, 1 subnets
C x.x.x.x is directly connected, Dialer0
S* 0.0.0.0/0 is directly connected, Dialer0
I also keep getting the message below on the console done know if this is part of the problem
Mar 13 07:17:32.213: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Vlan1: the fragment table h
as reached its maximum threshold 16
Hope this output helps
Thanks -
Telnet not working i need help : Could not open connection to the host !!
hello all im back today with big problem with telnet i dont know why !!
i have to computers one of them in my home and the other one in my office both of them use windows 7 so
home PC internet IP : 82.205.100.161
office PC internet IP : 82.102.237.175
so i go to control panel and then to windows features and i check Telnet Client and Telnet server
then i turn off my firewall
then i start telnet service
then i execute netstat -ab to know telnet port :
[tlntsvr.exe]
TCP [::]:135 Hacker-HP:0 LISTENING
is there anythink i need to do to get that damn connection over internet NOT LAN !! pleaze help me i still get this sucks error : Could not open connection to the host
peace
Dr.BL@CKDeaTHHi,
Telnet server use TCP port 23 by default.
Here is a screenshot of my lab server,
To verify if the TCP port 23 has been opened, we can use the portqry tool.
Here is the download link,
http://www.microsoft.com/en-us/download/details.aspx?id=17148
Best Regards.
Steven Lee
TechNet Community Support -
Could not open connection to the SERVER
Below is the error message that i have encountered.
I am using Java version 7.
Also tried installing the previous versions as well.
But when i check the connection using the ODBS data source administrator i was able to connect the server.
!ENTRY com.sap.ndb.studio.navigator 4 1 2014-06-24 00:25:17.142
!MESSAGE HDB skvk.vm.cld.sr 00 (SYSTEM) Error while refreshing system
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 0 2014-06-24 00:25:17.142
!MESSAGE SAPControl request failed
!STACK 0
com.sap.ndb.studio.sapcontrol.SAPControlException: SAPControl request failed
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:118)
at com.sap.ndb.studio.sapcontrol.SAPControl.getInstanceProperties(SAPControl.java:507)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTrySAPControl(SAPSystemObjectUpdate.java:147)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:79)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.call(Unknown Source)
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:94)
... 6 more
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.post(Unknown Source)
... 8 more
Caused by: java.net.SocketException: Connection reset
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(Unknown Source)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(Unknown Source)
at java.lang.reflect.Constructor.newInstance(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at sun.net.www.protocol.http.HttpURLConnection.getChainedException(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
at java.net.HttpURLConnection.getResponseCode(Unknown Source)
... 9 more
Caused by: java.net.SocketException: Connection reset
at java.net.SocketInputStream.read(Unknown Source)
at java.net.SocketInputStream.read(Unknown Source)
at java.io.BufferedInputStream.fill(Unknown Source)
at java.io.BufferedInputStream.read1(Unknown Source)
at java.io.BufferedInputStream.read(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTPHeader(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
... 11 more
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 4 2014-06-24 00:25:17.143
!MESSAGE Database connection is not available. See error log for details.
!STACK 0
com.sap.ndb.studio.jdbc.JDBCConnectionStatus: Database connection is not available. See error log for details.
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:253)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException: Data receive failed .
at com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException.createException(SQLNonTransientConnectionException.java:40)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:241)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:203)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.generateSQLException(SQLExceptionSapDB.java:155)
at com.sap.db.jdbc.exceptions.ConnectionException.createException(ConnectionException.java:22)
at com.sap.db.jdbc.ConnectionSapDB.tryReconnect(ConnectionSapDB.java:1631)
at com.sap.db.jdbc.ConnectionSapDB.execute(ConnectionSapDB.java:1131)
at com.sap.db.jdbc.CallableStatementSapDB.sendCommand(CallableStatementSapDB.java:1964)
at com.sap.db.jdbc.StatementSapDB.sendSQL(StatementSapDB.java:978)
at com.sap.db.jdbc.CallableStatementSapDB.doParse(CallableStatementSapDB.java:256)
at com.sap.db.jdbc.CallableStatementSapDB.constructor(CallableStatementSapDB.java:215)
at com.sap.db.jdbc.CallableStatementSapDB.(CallableStatementSapDBFinalize.java:31)
at com.sap.db.jdbc.ConnectionSapDB.prepareStatement(ConnectionSapDB.java:1369)
at com.sap.db.jdbc.trace.log.Connection.prepareStatement(Connection.java:1025)
at com.sap.db.jdbc.trace.Connection.prepareStatement(Connection.java:413)
at com.sap.ndb.studio.jdbc.JDBCConnection.initialize(JDBCConnection.java:235)
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:236)
... 5 more
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.869
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:116);csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:1);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.871
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.catalog.internal.Catalog.isHasPrivilegesForSchemasAvailable(Catalog.java:143);csns.catalog.internal.Catalog.fetchCatalogObjects(Catalog.java:73);csns.catalog.internal.CatalogFolder.fetchChildren(CatalogFolder.java:175);csns.catalog.CatalogWorkbenchAdapter$1.run(CatalogWorkbenchAdapter.java:98);org.eclipse.core.internal.jobs.Worker.run(Worker.java:53);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.873
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.catalog.command.handlers.CatalogRefresh.execute(CatalogRefresh.java:36);org.eclipse.ui.internal.handlers.HandlerProxy.execute(HandlerProxy.java:290);org.eclipse.ui.internal.handlers.E4HandlerProxy.execute(E4HandlerProxy.java:90);org.eclipse.e4.core.internal.di.MethodRequestor.execute(MethodRequestor.java:56);org.eclipse.e4.core.internal.di.InjectorImpl.invokeUsingClass(InjectorImpl.java:243);org.eclipse.e4.core.internal.di.InjectorImpl.invoke(InjectorImpl.java:224);org.eclipse.e4.core.contexts.Context)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.875
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.catalog.internal.Catalog.isHasPrivilegesForSchemasAvailable(Catalog.java:143);csns.catalog.internal.Catalog.fetchCatalogObjects(Catalog.java:73);csns.catalog.internal.CatalogFolder.fetchChildren(CatalogFolder.java:175);csns.catalog.CatalogWorkbenchAdapter$1.run(CatalogWorkbenchAdapter.java:98);org.eclipse.core.internal.jobs.Worker.run(Worker.java:53);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.894
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.modeler.base.NavigatorRepositoryInput.getConnection(NavigatorRepositoryInput.java:28);csns.sdk.repository.provider.newdbrepository.NewDBRepositoryProxyFactory.getRepositoryProxy(NewDBRepositoryProxyFactory.java:21);csns.sdk.repository.provider.newdbrepository.impl.NewDBRepositoryProvider.getProxy(NewDBRepositoryProvider.java:197);csns.sdk.repository.provider.newdbrepository.impl.NewDBRepositoryProvider.checkRepositoryAccessAuthorization(NewDBRepositoryProvider.java:214);csns.sdk.repository.newdbreposi)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.896
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.catalog.internal.Catalog.isHasPrivilegesForSchemasAvailable(Catalog.java:143);csns.catalog.internal.Catalog.fetchCatalogObjects(Catalog.java:73);csns.catalog.internal.CatalogFolder.fetchChildren(CatalogFolder.java:175);csns.catalog.CatalogWorkbenchAdapter$1.run(CatalogWorkbenchAdapter.java:98);org.eclipse.core.internal.jobs.Worker.run(Worker.java:53);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.899
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.catalog.internal.Catalog.isHasPrivilegesForSchemasAvailable(Catalog.java:143);csns.catalog.internal.Catalog.fetchCatalogObjects(Catalog.java:73);csns.catalog.internal.CatalogFolder.fetchChildren(CatalogFolder.java:175);csns.catalog.CatalogWorkbenchAdapter$1.run(CatalogWorkbenchAdapter.java:98);org.eclipse.core.internal.jobs.Worker.run(Worker.java:53);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:26:07.901
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268);csns.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96);csns.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73);csns.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70);csns.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99);)
!ENTRY com.sap.ndb.studio.backup 4 4 2014-06-24 00:27:01.078
!MESSAGE Could not open connection to 'HDB skvk.vm.cld.sr 00'
!STACK 0
java.util.concurrent.TimeoutException
at java.util.concurrent.FutureTask.get(Unknown Source)
at com.sap.ndb.studio.backup.BackupConnectionHandler.openConnection(BackupConnectionHandler.java:122)
at com.sap.ndb.studio.backup.BackupConnectionHandler.getConnection(BackupConnectionHandler.java:88)
at com.sap.ndb.studio.backup.BackupWorkbenchAdapter$2.call(BackupWorkbenchAdapter.java:151)
at com.sap.ndb.studio.backup.BackupWorkbenchAdapter$2.call(BackupWorkbenchAdapter.java:1)
at java.util.concurrent.FutureTask.run(Unknown Source)
at java.util.concurrent.ThreadPoolExecutor.runWorker(Unknown Source)
at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
!ENTRY com.sap.ndb.studio.navigator 4 1 2014-06-24 00:27:31.615
!MESSAGE HDB skvk.vm.cld.sr 00 (SYSTEM) Error while refreshing system
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 0 2014-06-24 00:27:31.615
!MESSAGE SAPControl request failed
!STACK 0
com.sap.ndb.studio.sapcontrol.SAPControlException: SAPControl request failed
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:118)
at com.sap.ndb.studio.sapcontrol.SAPControl.getInstanceProperties(SAPControl.java:507)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTrySAPControl(SAPSystemObjectUpdate.java:147)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:79)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.call(Unknown Source)
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:94)
... 6 more
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.post(Unknown Source)
... 8 more
Caused by: java.net.SocketException: Connection reset
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(Unknown Source)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(Unknown Source)
at java.lang.reflect.Constructor.newInstance(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at sun.net.www.protocol.http.HttpURLConnection.getChainedException(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
at java.net.HttpURLConnection.getResponseCode(Unknown Source)
... 9 more
Caused by: java.net.SocketException: Connection reset
at java.net.SocketInputStream.read(Unknown Source)
at java.net.SocketInputStream.read(Unknown Source)
at java.io.BufferedInputStream.fill(Unknown Source)
at java.io.BufferedInputStream.read1(Unknown Source)
at java.io.BufferedInputStream.read(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTPHeader(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
... 11 more
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 4 2014-06-24 00:27:31.616
!MESSAGE Database connection is not available. See error log for details.
!STACK 0
com.sap.ndb.studio.jdbc.JDBCConnectionStatus: Database connection is not available. See error log for details.
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:253)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException: Data receive failed .
at com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException.createException(SQLNonTransientConnectionException.java:40)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:241)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:203)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.generateSQLException(SQLExceptionSapDB.java:155)
at com.sap.db.jdbc.exceptions.ConnectionException.createException(ConnectionException.java:22)
at com.sap.db.jdbc.ConnectionSapDB.tryReconnect(ConnectionSapDB.java:1631)
at com.sap.db.jdbc.ConnectionSapDB.execute(ConnectionSapDB.java:1131)
at com.sap.db.jdbc.CallableStatementSapDB.sendCommand(CallableStatementSapDB.java:1964)
at com.sap.db.jdbc.StatementSapDB.sendSQL(StatementSapDB.java:978)
at com.sap.db.jdbc.CallableStatementSapDB.doParse(CallableStatementSapDB.java:256)
at com.sap.db.jdbc.CallableStatementSapDB.constructor(CallableStatementSapDB.java:215)
at com.sap.db.jdbc.CallableStatementSapDB.(CallableStatementSapDBFinalize.java:31)
at com.sap.db.jdbc.ConnectionSapDB.prepareStatement(ConnectionSapDB.java:1369)
at com.sap.db.jdbc.trace.log.Connection.prepareStatement(Connection.java:1025)
at com.sap.db.jdbc.trace.Connection.prepareStatement(Connection.java:413)
at com.sap.ndb.studio.jdbc.JDBCConnection.initialize(JDBCConnection.java:235)
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:236)
... 5 more
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:38:11.748
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.navigator.commands.OpenSAPSystemHandler$1$1.call(OpenSAPSystemHandler.java:238);csns.navigator.commands.OpenSAPSystemHandler$1$1.call(OpenSAPSystemHandler.java:1);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:38:11.749
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:116);csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:1);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:38:11.750
!MESSAGE Connection on HDB:SKVK.VM.CLD.SR:00:SYSTEM is forced to close. (csns.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268);csns.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96);csns.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73);csns.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70);csns.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:38:15.378
!MESSAGE Connection on HDB:BRSL.VM.CLD.SR:00:SYSTEM is forced to close. (csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:116);csns.backup.BackupConnectionHandler$1.call(BackupConnectionHandler.java:1);)
!ENTRY com.sap.ndb.studio.jdbc 4 4 2014-06-24 00:38:15.384
!MESSAGE Connection on HDB:BRSL.VM.CLD.SR:00:SYSTEM is forced to close. (csns.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268);csns.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96);csns.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73);csns.datamodel.controler.DataModelOperationJob.run(DataModelOperationJob.java:70);org.eclipse.core.internal.jobs.Worker.run(Worker.java:53);)
!ENTRY com.sap.ndb.studio.backup 4 4 2014-06-24 00:39:08.472
!MESSAGE Could not open connection to 'HDB skvk.vm.cld.sr 00'
!STACK 0
java.util.concurrent.TimeoutException
at java.util.concurrent.FutureTask.get(Unknown Source)
at com.sap.ndb.studio.backup.BackupConnectionHandler.openConnection(BackupConnectionHandler.java:122)
at com.sap.ndb.studio.backup.BackupConnectionHandler.getConnection(BackupConnectionHandler.java:88)
at com.sap.ndb.studio.backup.BackupWorkbenchAdapter$2.call(BackupWorkbenchAdapter.java:151)
at com.sap.ndb.studio.backup.BackupWorkbenchAdapter$2.call(BackupWorkbenchAdapter.java:1)
at java.util.concurrent.FutureTask.run(Unknown Source)
at java.util.concurrent.ThreadPoolExecutor.runWorker(Unknown Source)
at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
!ENTRY com.sap.ndb.studio.navigator 4 1 2014-06-24 00:39:38.422
!MESSAGE HDB skvk.vm.cld.sr 00 (SYSTEM) Error while refreshing system
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 0 2014-06-24 00:39:38.422
!MESSAGE SAPControl request failed
!STACK 0
com.sap.ndb.studio.sapcontrol.SAPControlException: SAPControl request failed
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:118)
at com.sap.ndb.studio.sapcontrol.SAPControl.getInstanceProperties(SAPControl.java:507)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTrySAPControl(SAPSystemObjectUpdate.java:147)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:79)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.call(Unknown Source)
at com.sap.ndb.studio.sapcontrol.operations.SAPControlOperation.execute(SAPControlOperation.java:94)
... 6 more
Caused by: com.sun.xml.internal.messaging.saaj.SOAPExceptionImpl: Message send failed
at com.sun.xml.internal.messaging.saaj.client.p2p.HttpSOAPConnection.post(Unknown Source)
... 8 more
Caused by: java.net.SocketException: Connection reset
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(Unknown Source)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(Unknown Source)
at java.lang.reflect.Constructor.newInstance(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection$6.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at sun.net.www.protocol.http.HttpURLConnection.getChainedException(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
at java.net.HttpURLConnection.getResponseCode(Unknown Source)
... 9 more
Caused by: java.net.SocketException: Connection reset
at java.net.SocketInputStream.read(Unknown Source)
at java.net.SocketInputStream.read(Unknown Source)
at java.io.BufferedInputStream.fill(Unknown Source)
at java.io.BufferedInputStream.read1(Unknown Source)
at java.io.BufferedInputStream.read(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTPHeader(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
at sun.net.www.http.HttpClient.parseHTTP(Unknown Source)
... 11 more
!SUBENTRY 1 com.sap.ndb.studio.navigator 4 4 2014-06-24 00:39:38.422
!MESSAGE Database connection is not available. See error log for details.
!STACK 0
com.sap.ndb.studio.jdbc.JDBCConnectionStatus: Database connection is not available. See error log for details.
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:253)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.executeTryJDBC(SAPSystemObjectUpdate.java:268)
at com.sap.ndb.studio.navigator.operations.SAPSystemObjectUpdate.execute(SAPSystemObjectUpdate.java:96)
at com.sap.ndb.studio.navigator.operations.UpdateSAPSystemOperation.execute(UpdateSAPSystemOperation.java:73)
at com.sap.ndb.studio.datamodel.controler.DataModelOperation.execute(DataModelOperation.java:70)
at com.sap.ndb.studio.datamodel.controler.DataModelOperationQueue$DataModelOperationThread.run(DataModelOperationQueue.java:99)
Caused by: com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException: Data receive failed .
at com.sap.db.jdbc.exceptions.jdbc40.SQLNonTransientConnectionException.createException(SQLNonTransientConnectionException.java:40)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:241)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.createException(SQLExceptionSapDB.java:203)
at com.sap.db.jdbc.exceptions.SQLExceptionSapDB.generateSQLException(SQLExceptionSapDB.java:155)
at com.sap.db.jdbc.exceptions.ConnectionException.createException(ConnectionException.java:22)
at com.sap.db.jdbc.ConnectionSapDB.tryReconnect(ConnectionSapDB.java:1631)
at com.sap.db.jdbc.ConnectionSapDB.execute(ConnectionSapDB.java:1131)
at com.sap.db.jdbc.CallableStatementSapDB.sendCommand(CallableStatementSapDB.java:1964)
at com.sap.db.jdbc.StatementSapDB.sendSQL(StatementSapDB.java:978)
at com.sap.db.jdbc.CallableStatementSapDB.doParse(CallableStatementSapDB.java:256)
at com.sap.db.jdbc.CallableStatementSapDB.constructor(CallableStatementSapDB.java:215)
at com.sap.db.jdbc.CallableStatementSapDB.(CallableStatementSapDBFinalize.java:31)
at com.sap.db.jdbc.ConnectionSapDB.prepareStatement(ConnectionSapDB.java:1369)
at com.sap.db.jdbc.trace.log.Connection.prepareStatement(Connection.java:1025)
at com.sap.db.jdbc.trace.Connection.prepareStatement(Connection.java:413)
at com.sap.ndb.studio.jdbc.JDBCConnection.initialize(JDBCConnection.java:235)
at com.sap.ndb.studio.jdbc.JDBCPlugin.createConnection(JDBCPlugin.java:236)
... 5 moreNo guarantee but try tapping Settings / Safari. Clear the History, Cookies, and Cache. Restart the iPad.
And try here.. Apple - Support - iPad - Wi-Fi -
my problem is my iphone 4s is connected to wi-fi with full signal(3 bars) strength but freezes when browsing and says
"Cannot Open Page"
"Safari could not open page because the server stopped responding"
I already reset the iphone to its factory settings and erase all contents but still the browsing speed freezes or not searching at all. Sometimes it will work and fast but then the problem uccors every now and then. Iv'e been using iphone 4 for two years and I still have it and works fine compared to this IPHONE 4S.Settings → scroll down to Safari → in Safari settings, I selected both Clear History and Clear Cookies and Data.
IF that does not work -
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
Finally - if problem still present -
Go to Settings>General>Reset
Reset the network settings - you will need to add the password of your home WiFi in your phone once more
The device should turn itself off & back on then go into Settings>Wifi and join your network -
Heart beat could not open connection, error code 110
Hi, where can I find error codes for NFR and NSM?
I have problems with some agents connecting to the engine:
2/17/2010 16:02:55 EngineInterface: Heart beat could not open connection, error code 110
Both engine and agent runs on the same server (10.236.19.147):
AgentNCP Service Config
Host Address: 10.236.19.147
Service Ports: HTTPS: 3037 HTTP: 0
Data Path: /var/opt/novell/filereporter/agentncp
Debug Logging: Enabled
Heartbeat: 60 seconds
Engine Address: 10.239.19.147:3035
Use SSL: Yes
Alternate Hostname: huanovellfs1
Engine Service Config
Host Address: 10.236.19.147
Service Ports
Client HTTPS: 3033 HTTP: 0
Agent HTTPS: 3035 HTTP: 0
Data Path: /var/opt/novell/filereporter/engine
Debug Logging: Enabled
Heartbeat: 60 seconds
DSI Address: 10.236.19.89:8009
Use SSL: Yes
Scans per Volume: 2
Another OES2 server connects fine to the engine, butI have a Netware agent, which also fails to connect:
Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open connection.
NFR is 1.0.0
Thanks for any input.
IstvanHi Istvan! Sorry for the delay in our response! we are in the process
of building a list of error codes for everyone! in the meantime the 110
means the following:
// Couldn't create a new network interface
#define CC_STATUS_CCS_CANT_CREATE 110
Is this an NSM integration installation?
Also, remove the alternate hostname.
If you don't mind, let's move this support issue to
filereporter"@"novell.com!
Thank you!
icseke wrote:
> Hi, where can I find error codes for NFR and NSM?
>
> I have problems with some agents connecting to the engine:
>
> 2/17/2010 16:02:55 EngineInterface: Heart beat could not open
> connection, error code 110
>
> Both engine and agent runs on the same server (10.236.19.147):
>
>
> AgentNCP Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports: HTTPS: 3037 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/agentncp
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> Engine Address: 10.239.19.147:3035
> Use SSL: Yes
> Alternate Hostname: huanovellfs1
>
> Engine Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports
> Client HTTPS: 3033 HTTP: 0
> Agent HTTPS: 3035 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/engine
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> DSI Address: 10.236.19.89:8009
> Use SSL: Yes
> Scans per Volume: 2
>
> Another OES2 server connects fine to the engine, butI have a Netware
> agent, which also fails to connect:
>
> Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open
> connection.
>
> NFR is 1.0.0
>
> Thanks for any input.
>
> Istvan
>
> -
Safari could not open page because the server stopped responding
"Could Not Open Page.... Safari could not open page because the server stopped responding"
....but it could worked just fine for the first 2 weeks of iPhone4 ownership.
WiFi network at home, working fine with MacBook, visiting friends' phones, my new iPhone4 - no problems. Had to power down the modem & router very briefly last night. Rebooted, MacBook connected fine, iPhone doesn't - it goes through the motions - shows all signs of full connection, full signal, password accepted etc etc - but web pages will not open, displaying after 30 secs the warning message above.
Tried at work on another wireless network - same response.
Have gone through all the FAQs, reset network settings, forgotten network etc - still nothing.
Anyone experienced the same and fixed it?
cheersI'm having a very similar problem, but it's with my 3G connection, not with wifi. The display tells me there is 3G connectivity, and I get the loading symbol, but pages stop loading a few seconds after I try to open them, and some time later I get the "server stopped responding" message. That happens with addresses I know are working, such as Google. Some times, restarting the iPhone or the internet connection (by switching plane mode on and off) solves the issue, but it has been happening often these days.
-
Restore Failure - Could not open connection to helper tool
I created a disk image on an external firewire drive using disk utility.
The external drive is bootable and I run the Disk Utility software from the external drive.
When I try to restore from the image selecting the source and target I get the following error after clicking the "Restore" button:
"Restore Failure
Could not open connection to helper tool."
Any suggestions on how to troubleshoot this?
Additional info:
MacBook Pro 2.16 Intel
Tiger 10.4.7
Boot ROM MBP12.0061.B00
SMC 1.5f10
Internal Hard Disk: ST9120821AS
External Hard Disk: FireLite FW800
All software and firmware up-to-date
Disk Utility 10.5.6 (198.12)I've experienced the same problem. What I know is that we built a system image using Disk Utility on a MacPro and we experience this error when attempting to restore the image on another MacPro using Disk Utility.
I've successfully built system images of MacBook Pros and restored them without any problems. However, I believe I may have built the image using Carbon Copy Cloner. This may warrant some more experimentation using the different utilities. -
Getting "Could not open connection to helper tool" when restoring a disk
I have installed OS X 10.4 on to my USB flash drive using the OS X disc that came with my iMac 24". I wanted to use the flash drive for booting the system in case I run into trouble with my iMac.
Everything was good. I was able to use the flash drive to boot my iMac with no problem. I made an image of the flash drive using Disk Utility. However, when I tried to restore it, Disk Utility kept reporting "Restore Failure: Could not open connection to helper tool". Please tell me what to do.
The USB flash drive is formatted using GUID Partition table.Same problem here.
I successfully created an image from a drive and I'm trying to restore to another drive.
I get the "preparing source..." for 2 seconds before the "Restore Failure" dialog with his geeky and meaningless error message. what is helper tool?! I thought I was using Disk Utility!!
Anybody can suggest a work around for yet another problem missed by QA ?
thanks in advance. -
SDM Deployment Problem. Could not establish connection to the server.
Hi all,
I am using J2ee Engine 2004s( version )server which is located remotely.I have installed NWDS 7.0.17 in client system & try to deploy an application. I could connect to the J2EE Engine through VPN Connection. but while deploying the application it is giving the following error
Deployment exception : Server XXX did not accept login request as admin on port 50018. Details: ERROR: Could not establish connection to server XXX at port 50018: Connection timed out: connect
Inner exception was :
Server XXX did not accept login request as admin on port 50018. Details: ERROR: Could not establish connection to server XXX at port 50018: Connection timed out: connect
I have made an host file entry also in my client System. I have used the Lib files also which is mentioned on SAP Note 941150.
still i am getting the same problem. Please bring me the solution to this problem. It would be really helpful.
Regards,
Malar.Hai,
Check the below link.....
http://help.sap.com/saphelp_nw70/helpdata/en/76/fb72ec091f4bf8a2d8ba321bb7e8d9/frameset.htm
SAP Note: 783965.
Regards,
Yoganand.V -
I am unable to connect to the itunes store; I get the message 'Itunes could not be connected to the itunes store. An unknown error occured (-3212). Also when I plug my iphone in to the computer it doesn't ever pick it up please help!!
same here no solutions
-
"could not open score because the project has no audio files"?
I just purchased the urban bundle from Resource Central, and uploaded it in "Bridge", I double-clicked the "sbst" file
to import to soundbooth and I get this, "could not open score because the project has no audio files"? when I single
click it in bridge the audio plays fine and shows the 4.61 file size, so there are audio files, can you tell me whats
going on?I FOLLOWED EVERYTHING YOU SAID, AND IT WORKED LIKE A CHARM
YOU ARE TRULY A PROFESSIONAL AND A SCOLAR!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
MUCHO THANKS. THANKS FOR NOT GIVING UP ON ME. YOU ARE THE
BEST!!! I GUESS MY PREVIOUS EXTRACTION THE FIRST TIME I TRIED
DID NOT WORK, BUT FOLLOWING YOUR STEPS GOT IT GOING.
THANK YOU ONCE AGAIN, NOW I NEED TO GO SEE "DOCTOR BOSLEY"
FOR SOME HAIR REPLACEMENT BECAUSE I PULLED IT ALL OUT TRYING
TO FIGURE OUT WHAT THE HELL I WAS DOING WRONG. THANKS AGAIN BRO. -
Could not obtain connection to the central environment.
Hi,
I have just started using iSetup on 11.5.10.2.
Initially I intend to use the same instance as source and central one.My understanding is that Source,Central and Target Instance are more of logical grouping and the same instance can be mapped for all the three.
I have mapped the instance that I am using as Source Instance and after that I try to run an Extract.The report is ending with error "Could not obtain connection to the central environment".
Kindly guide on what needs to be done to map the same instance as Source,Central and Target.
Do i need to map in thrice?
Regards
VikasFind Below the Requested Sh run outputs
ADSL-ROUTER1#sh run | beg line vty
line vty 0 4
password 7 ***********
login
scheduler max-task-time 5000
end
I have removed the IP for security reasons
ADSL-ROUTER1#sh ip route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
x.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
S x.x.x.x/29 is directly connected, Vlan1
C x.x.x.x/32 is directly connected, Dialer0
x.0.0.0/32 is subnetted, 1 subnets
C x.x.x.x is directly connected, Dialer0
S* 0.0.0.0/0 is directly connected, Dialer0
I also keep getting the message below on the console done know if this is part of the problem
Mar 13 07:17:32.213: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Vlan1: the fragment table h
as reached its maximum threshold 16
Hope this output helps
Thanks
Maybe you are looking for
-
Interactive PDF on IPad app created with Digital Publishing Suite
Can someone tell me why I can create an Interactive PDF in InDesign, send it to Adobe Forms but not be able to have an Interactive PDF form on an IPad App built with InDesign? Is having an Interactive (by that I mean, adding a name and address and an
-
Hi, I have a requirement to lookup from an Excel/CSV file for a field. I have seen many blogs/threads but I need advice from somebody who has worked on this scenario and if its practical. If possible end to end. Regards...
-
Air print using my Iphone and B110 printer.
How do I connect my B110 with my iphone using a third party application so I can print ?Air print. thanks Bernard
-
Function Module for ATP Check specific to BATCH
Hi All, I have a requriement where I need to find the available stock for a material for a given plant and most importantly BATCH. I tried using BAPI_MATERIAL_AVAILABILTY, but it returns the overall stock avaliable at the plant level irrespective whe
-
Server failing to run multiple services after Windows Update ran last night.
SBS 2011 Server was restarted to complete installation of 8 critical security updates last night. A number of services all dependent on RPC Service will not run today. I uninstalled all the updates and restarted Server but still have the same problem