Couldn't see LUNS fpr Compaq Storage array 1000 solaris box

Hi All,
I want to connect Compaq storage Works SAN array to solaris10 Box. I can see array as connected but state as unusable.
How can i see the luns from the storage on solaris box??
dmesg output:
Feb 1 08:29:54 testappl        ndi_devi_online: failed for array-controller: target=11000 lun=0 ffffffff
Feb 1 08:30:25 testappl fctl: [ID 517869 kern.warning] WARNING: fp(7)::PLOGI succeeded: no skip(2) for D_ID 11000
Feb 1 08:30:25 testappl genunix: [ID 599346 kern.warning] WARNING: Page83 data not standards compliant COMPAQ   MSA1000          2.38
Feb 1 08:30:25 testappl scsi: [ID 243001 kern.info] /pci@1d,700000/SUNW,emlxs@2/fp@0,0 (fcp7):
Feb 1 08:30:25 testappl        ndi_devi_online: failed for array-controller: target=11000 lun=0 ffffffff
Feb 1 08:47:27 testappl emlxs: [ID 349649 kern.info] [ 5.05F8]emlxs3: NOTICE: 730: Link reset.
Feb 1 08:47:27 testappl emlxs: [ID 349649 kern.info] [ 5.0337]emlxs3: NOTICE: 710: Link down.
Feb 1 08:47:30 testappl emlxs: [ID 349649 kern.info] [ 5.054D]emlxs3: NOTICE: 720: Link up. (2Gb, fabric, initiator)
Feb 1 08:47:30 testappl genunix: [ID 599346 kern.warning] WARNING: Page83 data not standards compliant COMPAQ   MSA1000          2.38
Feb 1 08:47:30 testappl scsi: [ID 243001 kern.info] /pci@1d,700000/SUNW,emlxs@2/fp@0,0 (fcp7):
Feb 1 08:47:30 testappl        ndi_devi_online: failed for array-controller: target=11000 lun=0 ffffffff
cfgadm -al output:
bash-3.00# cfgadm -al
Ap_Id                          Type         Receptacle   Occupant     Condition
c0                             scsi-bus     connected    configured   unknown
c0::dsk/c0t0d0                 CD-ROM       connected    configured   unknown
c1                             scsi-bus     connected    configured   unknown
c1::dsk/c1t0d0                 disk         connected    configured   unknown
c1::dsk/c1t1d0                 disk         connected    configured   unknown
c1::dsk/c1t2d0                 disk         connected    configured   unknown
c2                             fc           connected    unconfigured unknown
c5                             scsi-bus     connected    unconfigured unknown
c6                             fc           connected    unconfigured unknown
c7                             fc-fabric    connected    configured   unknown
c7::500805f3000186d9           array-ctrl   connected    configured   unusable
usb0/1                         usb-device   connected    configured   ok
usb0/2                         unknown      empty        unconfigured ok
usb1/1                         unknown      empty        unconfigured ok
usb1/2                         unknown      empty        unconfigured okthanks in advance.

Looks like the LUN is not configured correctly on the storage array. The kernel can't take the LUN online.
I have seen this on various boxes, most of the time it was either that the LUN wasn't set online on the SAN box or there is a SCSI reservation on the LUN.
Can you access the LUN from another host?

Similar Messages

SVM - Storage array migration effort

We have several Solaris servers which have both internal drives not under SVM control and Array based SVM devices built into filesystems.
We need to do 2 things:
1) Migrate internal drives to Array based luns
2) Migrate existing SVM luns to new storage array.
I found and read through the Admin guide for SVM, and it appears to address "migration" only in relation to creating a mirror for an existing volume.
What I would like to do is replace (or mirror) the underlying devices of an existing filesystem, not the entire filesystem at the top level.
Im much more familiar with Linux LVM, where I would add new PV's to an existing VG and use the pvmove command.
I don't see a similiar capability in Solaris 10 LVM so wanted to check with the more experienced folks on how to proceed with this array migration effort.
Thanks

We are moving from an 10+ yr old HDS to a new VNX.
While EMC can physically move the data, I don't have any way to change the config on the SVM (that I know of) to use the new devices.
AFAIK I would have to do the migration at the SVM layer in order for the FS to be properly linked to it's underlying LUNS.
As for the existing FS on the local disk, that can be done by umounting the FS and moving, but I don't see an easy way to migrate the root volume without a rebuild of the root filesystem...

ISCSI Initator still connects to NAS after deleting OVM Storage Array

I've got a 3.0.2 test rig with a couple of VM servers, a VM Manager and an Iomega NAS
I have a working solution using NFS storage, so the next step was to get a working solution with iSCSI
I started by enabling iSCSI and creating LUNs on an Iomega NAS
I then created an iSCSI Storage Array in OVM which pointed at the NAS
I registered a couple of iSCSI Initators in the OVM configuration.
I then created a server pool etc and everything looks good
Time to cleanup
I deleted ISCSI based repository contents and then the serverpool.
I deleted the LUNS from the OVM Storage Array definition
I tried to remove the iSCSI Initators but it said it couldn't do that with an iSCSI generic initator
I deleted the OVM Storage array
I then went to the Iomega NAS to delete the LUNs and it says that there are still VM Server iSCSI Initators connected.
I suspect I will be able to get rid of the iSCSI initiators connecting to the NAS by shutting down my two VM Servers and then rebooting the NAS. Since the VM servers aren't running there will be no connections coming from them so I will be able to delete the LUNS and turn off iSCSI.
Should the delete of the OVM storage Array definition have deleted the iSCSI Initators or did I miss a step somewhere ?
At this point, is there an easier to way to cleanup without rebooting everything ?

After hooking up a couple of OVM3.0.2 servers setup to an HP P4000 VSA - I noticed that when deleting iSCSI LUNs first from VM Manager, and then from the VSA - after rebooting the hosts - the OVM servers would try to connect to the LUNs even though they had been deleted.
If the LUN was deleted from VM Manager, but not the SAN - the LUN would just re-appear.
If the LUN was deleted from VM Manager, along with the iSCSI Disk Array registration - the LUN would end up in 'unmanaged iSCSI array'.
For some reason I can't seem to un-assign a server initiator from the arrays 'default access group'. I guess perhaps this is the problem.
The only way to get around this is to delete the entire array registration!
I created an SR and the latest news on that is that it's been filed as a bug.....
Jeff

Error while Registering a iSCSI drive on to Storage array

Hi,
I've installed Oracle VM Manager 3.0.2 on Oracle Linux 6.1. When I tried to register a iSCSI drive on to Storage array, I go the following error:
"java.lang.NullPointerException
ADF_FACES-60097:For more information, please see the server's error log for an entry beginning with: ADF_FACES-60096:Server Exception during PPR, #4"
Also there is no items to be selected in the Storage Plug-in.
I read that Storage plug-in is in-built with version 3.0 and above.
Any help in this regard will be greatly appreciated.
Thanks,
Prajeesh

Prajeesh wrote:
Also there is no items to be selected in the Storage Plug-in.Have you discovered at least one Oracle VM Server yet? You can't add any storage until you do that successfully.

Storage Array (EqualLogic) Status: Not Responding in VMM

We have a customer running SCVMM 2012 SP1, using 2 nodes and the underlying storage is an EqualLogic box.
Worked fine for a while, but a couple of weeks ago their SCVMM started complaining about failed jobs regarding the storage provider. The error message is:
Error (2912)
An internal error has occurred trying to contact the VP-SCVMM01.customer.local server: :a:DestinationUnreachable: :MI RESULT 6:The requested object could not be found..
WinRM: URL: [http://vp-scvmm01.customer.local:5985], Verb: [GET], Resource: [http://schemas.microsoft.com/wbem/wsman/1/wmi/root/microsoft/windows/storage/MSFT_StorageSubSystem?ObjectId={1}\\VP-SCVMM01\root/Microsoft/Windows/Storage/Providers\EQL_StorageSubSystem.ObjectId="6019CB11A5A29937571EA5"]
The handle is invalid (0x80070006)
Recommended Action
Check that WS-Management service is installed and running on server VP-SCVMM01.customer.local. For more information use the command "winrm helpmsg hresult". If VP-SCVMM01.customer.local is a host/library/update server or a PXE server role then ensure that VMM agent is installed and running.
The storage provider in SCVMM is listed as "not responding" as is the Array itself.
Anybody any idea to resolve this?
The closest thing I could find was this thread, somebody mentions the same problem: http://social.technet.microsoft.com/wiki/contents/articles/12038.vmm-2012-sp1-installing-and-configuring-dell-equallogic-ps-series-smp-provider.aspx
Only difference is that we didn't do any upgrade or change. Based on his comment I would like to remove the storage provider and re-add it but I want to make sure that removing it doesn't break anything for the LUN's or the fact they keep being presented
to the hosts.

Hello...
What version of Dell EqualLogic Host Integration Tools for Microsoft are you using?
Are you able to manage EqualLogic storage using the SMP Provider from native Windows File and Storage Services in Server Manager?
Basic troubleshooting steps I would recommend are to restart the "EqualLogic SMP Host Service" - and perhaps also restart "Windows Remote Management (WS-Management)" Service.
Has anything recently changed on the Dell EqualLogic group - such as admin account credentials, ip address changes, or the introduction of management interfaces? I would check to ensure that the SMP Provider is properly configured (username, password,
group ip or management ip, etc...). You can do this via the Dell EqualLogic PowerShell Tools or via Dell EqualLogic Auto-Snapshot Manager / Microsoft Edition.
Here is a useful Deployment and Configuration Guide for using the Dell EqualLogic SMP Provider with SCVMM 2012 SP1:
http://en.community.dell.com/techcenter/extras/m/white_papers/20437936.aspx
Keep me posted. Good luck.

Error: -69774: Couldn't bring the new Core Storage Logical Volume online

Hi,
I have a filevault encrypted drive (750GB).
I first noticed a problem when it prompted my for the FileVault passphrase (which I had stored in my keychain) and entering the correct passphrase resulted in the typical "error" response (the sideways "bouncing" entry field) asking me for the passphrase again.
So I get a list of the corestorage to get the UUID of the encrypted volume:
>diskutil corestorage list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group ********-****-****-****-************
    =========================================================
    Name:         750GB APPLE HDD
    Status:       Online
    Size:         749812400128 B (749.8 GB)
    Free Space:   0 B (0 B)
    |
    +-< Physical Volume ********-****-****-****-************
    |   ----------------------------------------------------
    |   Index:    0
    |   Disk:     disk2s2
    |   Status:   Online
    |   Size:     749812400128 B (749.8 GB)
    |
    +-> Logical Volume Family ********-****-****-****-************
        Encryption Status:       Locked
        Encryption Type:         AES-XTS
        Conversion Status:       Complete
        Conversion Direction:    -none-
        Has Encrypted Extents:   Yes
        Fully Secure:            Yes
        Passphrase Required:     Yes
        |
        +-> Logical Volume ********-****-****-****-************
            Disk:                  -none-
            Status:                Locked
            Size (Total):          749493624832 B (749.5 GB)
            Conversion Progress:   -none-
            Revertible:            No
            LV Name:               750GB APPLE HDD
            Content Hint:          Apple_HFS
Using command line I get the following response:
>diskutil corestorage unlockvolume UUID -stdinpassphrase
{UUID being the one of the last Logical Volume named "750GB APPLE HDD"}
Passphrase:
Started CoreStorage operation
Logical Volume successfully unlocked
Error: -69774: Couldn't bring the new Core Storage Logical Volume online
next I try:
>diskutil corestorage revert UUID -stdinpassphrase
Passphrase:
Started CoreStorage operation on disk3
Error: -69741: The target disk isn't eligible for reversion because it wasn't created by conversion or it is not part of a simple setup of exactly one logical and one physical volume
and then:
>diskutil corestorage unlockvolume UUID -stdinpassphrase
Passphrase:
Error beginning CoreStorage Logical Volume unlock: The target Core Storage volume is not locked (-69748)
looking at the kernel log I see the following interesting entries:
08.12.13 15:32:47,000 kernel[0]: CoreStorage: fsck_cs has finished for group "UUID" with status 0x00
08.12.13 15:32:47,000 kernel[0]: CoreStorageFamily::unlockVEKs() failed to unwrap the vek, status = e00002bc
08.12.13 15:33:10,000 kernel[0]: CoreStorageGroup::completeIORequest - error 0xe00002ca detected for LVG "750GB APPLE HDD" (UUID), pv UUID-of-Physical-Volume, near LV byte offset = 0.
08.12.13 15:34:51,000 kernel[0]: CoreStorageGroup::completeIORequest - error 0xe00002d9 detected for LVG "750GB APPLE HDD" (UUID), pv UUID-of-Physical-Volume, near LV byte offset = 0.
BTW: after a while I also hear a single clicking sound (head jumping back on drive) so I am not sure if it might be a physical disk failure.
Any ideas anyone?

Also, I've tried Terminal command: diskutil corestorage revert UUID -stdinpassphrase which returned "Error: -69854: A disk with a mount point is required"
Also, I've tried Terminal command: diskutil corestorage changeVolumePassword UUID -newpassphrase which returned "Error beginning CoreStorage Logical Volume unlock: The target Core Storage volume is not encrypted (-69755)"

Undocumented system messages issued by T3+ Storage Array

Hi,
     we have a T3+ Storage Array.
     From several days i've been seeing messages in the logs, issued by the T3+, like these below:
     Sep 01 14:06:22 t3.domain.tld SNXT[1]: N: u1ctr Failed writing system area err=14
     Sep 01 14:06:22 t3.domain.tld MASD[1]: N: u1ctr Failed writing system area err=14
     Sep 01 14:06:22 t3.domain.tld MNXT[1]: N: u1ctr Failed writing system area err=14
     I've searched the net and SunSolve, but didn't find any relevent information.
     Could someone direct me to the possible reasons/problems messages are related to ?
     Thanks in advance!
          Vladimir

I have the same problem on my thinkpad T500 after I upgrade the wireless card (intel wifi link 5300).
For a long time I didn't understand the why of this behavior, but some weeks ago I realise that the problem can solve it hard-locking the wireless card and unlocking after the step: "loading modules".
For more information this is the complete thread on thinkpad forum that I wrote when I try to solve this issue: http://lnv.lithium.com/t5/T400-T500-and … 870#M26238
I apologize if you do not understand what I mean, the problem is that I have some difficulties to express myself in English

SCVMM 2012 R2 - Adding A Storage Array

Good Afternoon,
I am having a little bit of a problem adding a Storage Array to SCVMM for my hosts. To quickly go through everything, I have done the following:
- Added iSCSI Storage Device through SMI-S
- Added LUN
- Allocated Storage Pool
-Added iSCSI array to host
Now here is where I think I went wrong: I removed the provider to make some changes to the SAN and readded it, however I didn't destroy the sessions on the hosts.
I followed the procedure again to readd the iSCSI array however now I don't have the "Add iSCSI Array" available in the host properties anymore.
Has anyone experienced this before?
Thanks,
Dan
----------------------------------------- Dan Sheppard

It is hard to tell why you are experiencing this.
What Update Rollup have you installed, and which version of VMM is this?
Did you follow the same steps as described in this blog? Ensure that all the mapping is correct so that the hosts actually will have access to the storage scope.
http://kristiannese.blogspot.no/2013/06/storage-management-with-datacenter.html
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

Migrate zpools to new storage array

I am in the process of migrating to a new EMC storage array. I used EMC SRDF to copy all tracks from the current disks to the new disks, so that all new disks look identical except for the actual device path since the WWN is different on the new array. I was hoping I could simply unmask/unmap the old SAN, mask and map the new SAN, and ZFS would be able to import the pools from the new SAN (like you can with veritas), but I didn't take into consideration that the device paths/names would be different and ZFS wouldn't like it. Is there any way to get solaris to see the new ZFS pools that now exist on the the new storage array so that I don't have to mirror and then remove the disks from the pool and pretty much wipeout all of the sync work I've already done with the EMC software?
Hopefully this makes sense, but please let me know if I need to explain further.

No issue, works as expected, I just didn't split the synchronization between the old and new devices, so the new disks were still write disabled in EMC land. Once I split the sync, everything imported without a hitch, so it was my stupid mistake.

What are some of the advantages/disadvantage of using FC or FCoE with a storage array (EMC)? What is Cisco's recommendation and why?

What are some of the advantages/disadvantages of using FC or FCoE for a storage array? What does Cisco recommend?

This is what I'm considering:
Power:
1050W Seasonic 80PLUS Gold Power Supply
Motherboard:
ASUS, Rampage IV Extreme, 2011, SATA6, True Quad SLI/XFIRE, Extreme OC Capable
CPU:
Intel Core i7-4960X 3.60GHz, 2133MHz DDR3, 15MB Cache, Hex Core Processor
System Memory:
16GB (4 x 4GB) , PC3-19200, 2400MHz (G.Skill - x79)
Video Adapter 1:
NVIDIA GeForce GTX 780ti 3GB GDDR5
Video Adapter 2:
None
Optical 1
16X Blu-ray Burner - 16xBD-R, 2xBD-RW/16xDVD-R, 8xDVD-RW/48xCD-R, 24xCD-RW
Bay Accessories 1
NZXT Aperture M Multi-media Hub
RAID [Requires Identical Hard Drive Selections]
RAID 0 | 2 Disk Min. Striped set, improved performance, additional storage drive highly recommended
Hard Drive 1
Crucial M550 1TB 2.5" SATA III 6GB/sec Solid State Drive
Hard Drive 2
Crucial M550 1TB 2.5" SATA III 6GB/sec Solid State Drive
Hard Drive 3
Crucial M550 1TB 2.5" SATA III 6GB/sec Solid State Drive
Sound Card
Creative Labs Sound Blaster Z PCI Express

Install solaris 10 on Proliant 1600 - Compaq Smart Array 221

I'm trying to install solaris 10 06/06 on a Proliant 1600 with smart array 221.
I boot from the cd and choose the first option (Solaris), then I get this warning:
WARNING: failed to program IO space [0/20/2] BAR@0x20 length 0x20
and the system hang up.
Does anyone know to what it is related to?
Thank you
Andrea V

I have the save problem when installing Solaris 10 on my System.
my configuration:
Proliant 1600
Compaq Smart Array 221
1 CPU 550mhz
512M RAM
It would be nice if somebody could help.
Edit:
The system crashes in the same way when I try to boot the "install check CD 1.1."
Message was edited by:
darthich

Sparc Storag Array 102 needs to run under solaris 10

I need to get a Sparc Storage Array to run under solaris 10. The soc driver that is needed is not supportted under solairs 10. I took the packages needed off of solari 9 cd and installed them but no luck. I tried to to do a modload and modinfo but it was not there.
The package loaded a file into /kernel/drv/sparcv9/soc. I have solaris 9 onanother disk on the same system and looked at the system trying to copy and edit the files on 10 but not device paths show up in the system. I copyied a file called soc that was in /kernel/drv/ I edited the /etc/device_aliases and path_to_inst but no good.
There are no entries in the /devices/ dir that reference the soc path. I do not if than can work but really would like to get this working.

The fibre interface on that beast is NOT a Gigabit connection,
such as is common on current systems.
It was a 100Mbps connection through an array controller,
running with a 40MHz microSPARC II control module.
You'd exceed its throughput capabilities in any attempt
to read or write data at or beyond that 100Mbps rate.
I don't anticipate much assistance in these forums for a technology that goes back a decade-and-a-half.
Contributors familiar with products from that era stopped posting in 2006
when the previous supportforum.sun.com was merged into this one.
We'll all look forward to your guidance after you succeed.
You'll teach the rest of us.

Sparc storage Array woring under solaris 10.

I need to get a Sparc Storage Array to run under solaris 10. The soc driver that is needed is not supportted under solairs 10. I took the packages needed off of solaris 9 cds and installed them but no luck. I tried to to do a modload and modinfo but it was not there.
The package loaded a file into /kernel/drv/sparcv9/soc. I have solaris 9 onanother disk on the same system and looked at the system trying to copy and edit the files on 10 but not device paths show up in the system. I copyied a file called soc that was in /kernel/drv/ I edited the /etc/device_aliases and path_to_inst but no good.
There are no entries in the /devices/ dir that reference the soc path. I do not if than can work but really would like to get this working.

Don't cross-post.
You already have an active thread on this topic in the other forum.
Cross-posting fragments any responses all over the universe.
As time passes and the threads get separated by time,
the responses become irrelevant.
That's why it's poor forum etiquette.
You end up diluting the information.

Purchased IOS Developer program but couldn't see any developer options after login using my apple id

On 15/06/14,I’ve purchased IOS Developer program by paying 99$,on 17/06/14 i got email from Apple reg Invoice No.But when i check the Order Status,it says “No Orders placed”.And AlsoI tried to login using my applied,but i couldn’t see the developer options.
I would request you all to let me know what happend to my order Status?

We are users like you. We have nothing to do with your enrollment. You need to go to the Online Store to formally purchase and pay for the membership.

Enabling a disk in T3 Storage Array

Currently using a T3 Storage Array where one of the drive slots is showing disabled. We have already replaced the bad disk and power cycled the array to try and enable the drive slot with no success. Does anyone know of a way to enable the drive slot other then deleting the volume and re-adding it?

Actually i was able to try it just yesterday without success. At the moment i have all of the disks previously mentioned installed, plus the new 240gb SSD. For some reason I am unable to add the new disk to the storage pool, and as a result unable
to remove the old 64gb disk.
Shaon, were you able to add a disk to a storage pool that contained a tiered storage virtual disk that consumed 100% of the storage pool space? When I try the options are all grayed out.
I do have backups of all of this data and I am capable of deleting the whole volume and starting over. However, this is new technology I would like to get familiar with in case I am presented with a similar problem in the future without the luxury
of backups.

Couldn't see LUNS fpr Compaq Storage array 1000 solaris box

Similar Messages

Maybe you are looking for