Count and timestamp logging messages: disabled

Hi ,
what does this setting "Count and timestamp logging messages: disabled" mean ? in "show logging" output.
I do not see the number of message lines logged ( syslog ) increasing under the "show logging" output,
Same is the case with the numbers in "Trap logging: level notifications, xxxx message line logged"
This is happening on IOS , any idea why ?
Thanks,

Hello Vikram,
If you do not have the time-stamp configured it would be more difficult to troubleshoot, lets explain this with an example:
-One of your interfaces went down at 13:30 your local time, you have logging enabled without the time-stamp so you go to your syslog server and you look for that problem, in that case you will need to go to all the syslog messages database ( witch might be huge and the message you are looking for could be imposible to find) so if you have timestamp enable you will go directly to the 13:30 messages and find it so much easier.
Here is another explanation I found for you:
logging timestamp
This command causes the firewall to add a time stamp to each Syslog message before it is sent. The firewall should have its clock set and time synchronized to a known and accurate source.
Please rate helpful posts,
Kind regards,
Julio

Similar Messages

  • Error stopping and undeploying java applications and View Log Messages link

    I was redirecting to this forum by instant chat JCS Support.
    Have a few issues with my JCS account:
    1) I am getting the following error when clicking View Log Messages hyperlink - Failed to get messages for service - java.
    2) Have 2 applications: Branding and Connectivity which I tried to stop or undeploy and getting errors for both.
    Could you help to resolve the both issues?

    Sorry, it was unfortunate that C2C could not help you. We had an issue last week with our console. Its now fixed, and you should not see this issue anymore. If you do continue to see an issue, post here and I will investigate.

  • [IN] and [OUT] log messages in Hibernate generated code in Eclipse

    Currently i have to make a code for generating log messages for the [IN] and [OUT] event of the methods, so i can trace the error easily
    ex.\\
    log.debug([IN]MyClass::myMethod() );
    log.debug([out]MyClass::myMethod() );
    what should i write to trace the inbound events and outgoing event tracing and i m new to struts, so above code is right or wrong i don't konw , please reply me immediately
    i m working on STRUTS..

    Don't double post.
    http://forum.java.sun.com/thread.jspa?threadID=712601&tstart=0

  • Suppress [Adobe CAPS DEBUG] and epic_core log messages

    Is there any way to suppress the [Adobe CAPS DEBUG] and epic_core messages that appear in the debug log? All those messages make it easy to miss asserts and other error messages.

    I switched over to an early 2008 20-inch iMac (booting from same external disk) and the "ERROR:shrink DB" and "assertion failed" messages are continuing, so I doubt that it is related to the hardware unless it's the external drive itself or the Firewire cable.
    Any help would be appreciated...

  • [IN] and [OUT] log messages coding [ URGENT REPLY NEEDED ]

    currently doing struts project in eclipse by generated code by hibernate
    and i want every method having facility for log
    IN and OUT log facility
    so could u please give me code that thing
    like : log.debug("[IN] MyClass::myMethod() );
    log.debug("[OUT] MyClass::myMethod() );
    so is it right or wrong, please anyone know quick reply me i need URGENT

    Don't double post.
    http://forum.java.sun.com/thread.jspa?threadID=712601&tstart=0

  • Locking Transcation and customized log messages

    Hi
    I wanna to lock a specific transcation and if users are executing the transaction code then a customized log meesage should popup or display and the transaction should terminate. Is there a way to do by std way instead of handeling it in coding? I dont wanna to create authroization objects as it is not a time to experiment with that considering the system landscape complexity.
    thkx
    Prabhu

    Hi,
    Use Authority Check statement.If the authority check fails raise an message.
    Regards
    Krishna

  • Difference between sysout log and server log???

    Hi All,
    from the long time am trying to find out the difference between sysout log and server log, can anyone please share me the info regarding that?
    Thanks.

    Server Logs
    The server log records information about events such as the startup and shutdown of servers,the deployment of new applications, or the failure of one or more subsystems. The messages include information about the time and date of the event as well as the ID of the user who initiated the event.
    Standard output logs
    In addition to writing messages to a log file, each server instance prints a subset of its messages to standard out. Usually, standard out is the shell (command prompt) in which you are running the server instance.WebLogic Server administrators and developers configure logging output and filter log messages to troubleshoot errors or to receive notification for specific events.
    Regards
    Fabian

  • Cjr2 error log messages

    Dear experts,
    I need to run cjr2 for several wbs elements and export log messages somewhere in SAP.
    The way it is now functioning is, by a pop up screen to show me the messages. Is there any way to export them, so as to use them later?
    thank you in advance,
    Roxani

    Speak to your hosting company techies.
    The "missing file" seems to belong in at a folder level ABOVE
    the www
    folder.
    I doubt you can access it, only your host.
    "Taxed Mind" <[email protected]> wrote in
    message
    news:erd3sp$80v$[email protected]..
    >I am receiving 100s of Error Log Messages through my
    server stats all
    >stating:
    > File does not exist:
    /........./............/public_html/...........
    > The site in question
    http://www.ruusutila.com
    appears to work perfectly on
    > my
    > and other computers.
    > On my Remote View the top file is www/ and within that I
    have three
    > folders;
    > _private, cgi-bin and images. There is no reference to
    public_html, I
    > presume
    > there should be but where and what should be in it I
    don't exactly know.
    > If I add a folder public_html where should I put it, and
    do I put all my
    > pages
    > in it or only the sites index (home) page? Should I also
    be setting it as
    > a
    > "Host Directory" or something, because I can't find any
    info on how to do
    > that
    > either?
    > Thanks in advance for your help.
    > A Taxed Mind
    >

  • Forgot passcode -find my iphone enabled -message disable find my iphone. I cannot do this as my phone is disabled.I logged onto icloud and removed the phone (can be done only when its offline

    I have completely forgotten my passcode and have find my iphone enabled. When I try to restore I get the message disable find my iphone. I cannot do this as my phone is disabled.I logged onto icloud and removed the phone (can be done only when its offline) but the phone keeps appearing.

    Do this:
    Plug in your iPhone into your computer.
    Hold the power button and home button for 10 seconds the both with each other.
    Then release the power button but keep holding the home button for another 15 seconds.
    This'll put it onto DFU mode so that you can restore it. Good luck!

  • Trying to download and keep getting message saying my Apple ID has been disabled but I can log into store, etc... I went to the support site buit no help. I emailed but said would take 2-4 days for response. I just wanna listen to my music!!

    Trying to download my music on a new PC. I've authorized PC and can log into store, etc.. But won't let me download. Says Apple ID disabled. No help on support site. I emailed but will take 2-4 days for response.

    We are all itunes users just like you
    You are not addressing Apple here at all
    You need to contact itunes support:
    http://www.apple.com/support/contact/

  • After updating to Firefox 7.0.1, menu bar for Google,yahoo, Facebook (message,notification,profile,home) and others site are disabled. How can solve this problem?

    after updating to Firefox 7.0.1, menu bar for Google(web ,image,video,map etc),yahoo, Facebook (message,notification,profile,home) and others site are disabled. even I cant log out from different sites cz the log out bar is completely disabled. I tried with Firefox 4;5 and 6, same problem exist . I tried by active all add ons for facebook, same problem exist. If I use internet explorer , I don't find such problem with it.
    How can I solve this problem?

    Thanks a lot for your swift response. And sorry if it was a bit too hectic to go through my detailed query (which I did because it was misunderstood when I asked previously). As I've mentioned above, I was informed that updating to 5.0.1 would '''require''' me to '''delete''' the current version and then install the new one. And doing so will involve losing all my bookmarks. I guess I should have been more specific and detailed there. By losing, I didn't mean losing them forever. I'm aware that they're secured in some place and deleting and installing the software doesn't harm its existence. What I meant that if I install the new version, I'd have to delete the old one. And after installing the new version, I'd have to transfer them (bookmarks) back from wherever they are. Get it? When it updated from 3.6.9 to 3.6.13, and from 3.6.13 to 3.6.18, I didn't need to follow that process. They were already present on their own.
    BTW, I'm having no problems with 3.6.18 but after learning about the existence of version 5.0.1, I'm a bit too eager to lay my hands over it.
    Thanks for your help; hope this wasn't extremely long.

  • /dev/hme and /dev/ip trace/log messages

    Hi,
    I want to enable debug messages from above drivers. I tried setting "ip_debug" flag using "ndd" but I did not see any debugging messaged in "/var/adm/messages". Where does IP send its debug messages? How about /dev/hme? Is there any debug facility?
    Thanks in advance.
    -Ashutosh

    Hi,
    You probably have this "logging" configuration set
    logging trap debugging
    This can be confirmed by using the below command to show all "logging" related configurations
    show run logging
    The "logging trap" sets the level of log messages that are sent to your Syslog server. So considering its set to "debugging" or "7" means that you are essentially logging everything possible with regards to the logging level.
    The more typical level for this is either "informational" or "notifications"
    I tend to keep it at "informational" though it generates a lot of logs still but its good in the sense that it logs all the connections/translations formed on the firewall and also logs when they are removed from the firewall.
    If you were to configure "notifications" you would only tend to see the connections attempts that are blocked by the firewall and the log amount would be pretty minimal
    Then again you also have the option to disable certain log messages altogether. You could for example disable the messages that tell you that a translation was formed/teardown which would already remove a considerable amount of logged messages.
    Then I guess there might be change to create a custom list of messages you are interested in also.
    You can also change the default level at which some logging level is logged.
    I guess the last options I mention would take some research on your part to determine which would serve you the best.
    The last options you mention in the post dont have anything to do with the Syslog servers logging. They are related to the console connection and the logs that is stored in the firewalls buffer which should be visible with the "show logging" command.
    Hope this information helps
    Please do mark the reply as the correct answer if it answered your question.
    Naturally ask more if needed
    - Jouni

  • Console message and system.log

    Hi,
    in the console system.log always apear this message every 30 second:
    +Feb 16 02:22:55 Macintosh SystemUIServer[346]: Error: ACInterfaceGetPower() called with invalid interface+
    +Feb 16 02:23:25: --- last message repeated 5 times ---+
    and every 5 second this other message:
    16/02/08 02:40:55 SystemUIServer[346] Error: ACInterfaceGetPower() called with invalid interface
    .. and the message look like an infinite loop message.
    Is it a problem ?
    And i can ear the Internal HD run always.
    Thanks on advice for any help
    Ale

    I just went through a bunch of research on this on my own iMac G5. (BTW - do you have an iMac G5 or an iMac Intel Core Duo? It can't be both)
    It comes down to the items that the SystemUIServer is trying to call. if you look at <homefolder>/Library/Preferences/com.apple.systemuiserver.plist and open it with TextEdit, you'll see that, among other things, it references 8 menuExtras -
    Battery.menu
    Displays.menu
    TimeMachine.menu
    Bluetooth.menu
    AirPort.menu
    Volume.menu
    Clock.menu
    User.menu
    While logged in as an administrative user, I launched System Preferences, Activity Monitor, and the Console looking at *+All Messages+*. I got the same ACInterfaceGetPower() error every 5 seconds, too. So I went through the Preferences and deactivated each menu item above, but the messages continued to appear.
    I had two items that might have been causing a problem. The first was the fact that I had the AirPort signal showing up in the menu bar, even though the Network location I have set up does not have AirPort as an available service. I added the Airport service back in, disabled the menu icon, removed the AirPort service again, and Applied the changes. I'm pretty sure the error message was still appearing at this point.
    The big change came when I opened up Accounts. First, I went to the Login Items section for my current user. I noticed that the EyeTV Helper and an Adobe process were both there along with the iTunes Helper process. I removed the first two using the "-" at the bottom. That actually appeared to fix it, but I proceeded to the Login Options section and disabled *Fast User Switching*. That removes the users from the menu bar. By this time the only thing left in the menu bar was the Spotlight icon.
    Switching over to Activity Monitor, I killed the SystemUIServer process. It restarted and the ACInterfaceGetPower() messages did not reappear. I then re-activated each item, one at a time, killing the SystemUiServer after each activation. Again, the messages did not appear. I did not re-activate Bluetooth or AirPort, since I do not need them.
    I am no longer getting those messages and the system appears to be running fine right now.
    I have an external monitor attached to the iMac G5 as well as 4 FireWire hard drives. I am connected to the outside world via FiOS and I have a 100 Mb CAT-5 connection to that router.

  • Turning off new message indicator AND the new message count

    Greetings,
    Is it possible to turn off both the new message indicator (red asterix) and the new message count?
    I would like no message indicators to appear on my blackberry home screen.
    Thanks ever so much for your help.

    I guess I didn't read close enough.  I don't think you can turn off the red asterisk.  It's going to show up on the icon no matter what. 
    As for the text messages, I'm not sure the setting for not showing message count indicator applies for text messges.  In fact, if you have OS 5, it most likely doesn't as sms is handled much differently.   
    You can turn off sounds and the red led in Profiles (or Sounds in OS 5)
    You're basically wanting to disabl everything the phone was designed to do.
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

  • Log messages for 'auditing' are different in 'general'  and'application log

    Hi,
    From UI, When I audit a file using a profile which comprises of user-defined 'rules/categories/analyzers', I will get log messages at ''File-name(Application) log window' and 'Messages' log window, which are located at bottom of Jdev UI page. One common message in both the log windows is
    " <n1> violations, <n2> exceptions, <n3> documents, <n4> seconds>.
    But here the 'n1,n2,...' numbers are dfferent in two windows though the log output is for a same file. In this the 'file-name' log shows the correct
    Example:-
    In 'file-name' log window ,it shows as:
    3 documents, 8 violations, no exceptions
    In messages window, it shows as
    "Audit starting on EFC.jpr (Default)
    Audit completed: no violations, no exceptions, 3 documents, 1 second"
    If I use the 'pre-existed'(Jdev's) rules profile, I will get similar output in both log windows.
    From this I concluded that there is something missing to register for a new 'rule/category/analyzer'.
    Could you suggest me in this case. Do I forgot anything to do in any files of '<rule-implementation.java>', 'audit.properties', <add-in launcher>.java, extension.xml.
    Actually, I want to use 'ojaudit' executable from command line to my project files. Here I observed that the output of the 'ojaudit' is similar to the above explained 'Message' log window in JDeveloper UI. But where the 'Message' log window output is not correct for user-defined rules.
    Regards
    Madhu

    Romano,
    In the upcoming production release (planned to be released next week), we added caching of authorized roles and permissions in JhsAuthorizationProxy class.
    I suggest you wait for this relase, if the problem persists, it is most likely an ADF issue (as is the logging)
    Steven Davelaar,
    JHeadstart team.

Maybe you are looking for