Covert LWAPP AP to autonomous possible?

Hi Sir,
I understand that I can convert autonomous AP to Lwapp AP and i know the steps of doing it.
My customer has lots of LWAPP APs but intend to convert it to autonomous. Can it be done? I find no info on how to convert Lwapp APs to autonomous.
Pleas advise.
Thank you.
Delon

Hi Delon,
This is very possible, have a look at the following;
Reverting the Access Point Back to Autonomous Mode
It is possible to revert an LWAPP-enabled Cisco Aironet access point back to autonomous mode. Please refer to Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode for detailed instructions on reverting to autonomous mode. Use this URL
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob
Please remember to rate helpful posts.......

Similar Messages

Converting back AP 2600 from Autonomous to LWAPP

Hello,
I have Cisco AP 2600, Previously i had converted it from LWAPP mode into Autonomous-Mode. But now I need to revert it back to LWAPP mode.
Can anyone send me the link on how to do it ?

HI Imran,
Yes you can convert it to lightweight. Just need the lightweight recovery image.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html
For the LWAP conversion, use the recovery image (example: c1140-rcvk9w8-tar.124-25d.JAL.tar). after thatuse the command on the autonomous AP priviledge mode.
AP#archive download-sw /force-reload /overwrite tftp://10.10.10.1/c1140-rcvk9w8-tar.124-25d.JA.tar
more detial ..follow this post:
http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
Regards
Dont forget to rate helpful posts

Autonomous or LWAPP for fast roaming

We are looking to deploy wifi to support Tablet PCs. The software we are using is very sensitive to loosing its connection to the SQL database. I am worried particually about roaming. We need to use 802.1x for security and would like to use the MS IAS servier with EAP-TLS for authentication. We have 4 locations which should each be well covered by 3 base stations at each location. Medical providers need to be able to move around the office without losing connections. Time is more important than money. An hour of lost provider time (and when our app crashes it crashes hard) is worth avoiding with addition money. My questions are the following:
1. Do we need LWAPP or will autonomous with WLSE work for us? (Specifically for fast secure roaming, or quick handoff, or whatever it is we need)
2. Do we need to use EAP-FAST (and thus a Cisco AAA server) or will EAP-TLS with IAS be enough?
3. If we use LWAPP do we need WCS or will managing each 2000 series WLAN controller be enough?
4. Will all this work with my HP switches and Andtran routers?

1. Do we need LWAPP or will autonomous with WLSE work for us? (Specifically for fast secure roaming, or quick handoff, or whatever it is we need)
A: Go with LWAPP, more reliable, and easier to work with.
2. Do we need to use EAP-FAST (and thus a Cisco AAA server) or will EAP-TLS with IAS be enough?
A: I'd recommend, PEAP. More secure, and with everything Cisco, much easier to support, since TAC does not support the IAS server.
3. If we use LWAPP do we need WCS or will managing each 2000 series WLAN controller be enough?
A: If you are only contemplatign using 2006 at 4 locations, WCS wouldn't be a necessity. If you expand beyond that and decide to do something else, then yes WCS.
4. Will all this work with my HP switches and Andtran router?
A: It probably will, and it should, but for best results, going Cisco for the whole solution works the best.
Now, why go with 2006's? They are nice boxes, but you would need 4 of them. If you are static at 4 locatiosn with out need for growth, I'd go with a 4402-25. This is a single controller that can handle up to 25 AP's. With this, if you purchase the 1242 or the 1131, you can do HREAP, and keep all the subnets locally switched, that way if the WAN goes out, or the controller goes out, then the WiFi stays up for the local subnets. Naturally anything acrosss the WAN is not accessable.
That beign said, if you are backhauling everything to a central site anyway, might as well go with one 4402-25, single point of controll, instead of 4. And if you do need to add another site, then you still have 13 more AP's that can join instead of having to purchase another controller.
my 2cents

Convert APs LWAPP to Autonomous without WLC

How can I convert an Access Point with lightweight version to autonomous without a Controller??
Regards,

Hi Juan Carlos,
No worries my friend, this should work :)
Here is a conversion method;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

LWAPP to Autonomous/IOS

I have a Aironet LAP-1232AG (AIR-LAP1232AG-A-K9) that I need to downgrade to an Autonomous AP. I can't find any documentation on how to do this. I have downloaded c1200-k9w7-tar.123-8.JA2.tar and set up a tftp server, but the LAP won't connect.
Any help would be GREATLY appreciated!

Hi Tom,
Here is the related info :)
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Hope this helps!
Rob

1142 autonomous to lwapp

hi folks:
Has anyone of you tried to convert autonomous to lwapp mode? I used upgrade tool v3.4 and it said 1140 is not supported. Or is there any other way to do the conversion? Thanks.
regards
Alex

Was it a LAP to begin with? If so, follow the "LWAPP revert to autonomous" steps using the recovery image as your file. Yes - I know you are going to LAP, not to autonomous. These steps worked great for me when going from autonomous back to LAP (without using the conversion tool):
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Set the timeout value on the TFTP server to 30 seconds.
Step 4 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

Can LWAPP be converted to Automous AP?

I have a LWAPP 1242 and I need it to be autonomous, can this be done?
Seth

Hi Seth,
This is most possible
Here is the related info :)
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272
Hope this helps!
Rob

Convertion from Lightweight to Autonomous access points

Is it possible to convert AIR-LAP1121G-E-K9 Lightweight access point to autonomous access point.

Hi tm,
You can convert AIR-LAP1121G-K-E9 to autonamus access point,pls do follow the procedur
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4
Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5
Disconnect power from the access point.
Step 6
Press and hold MODE while you reconnect power to the access point.
Step 7
Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8
Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9
After the access point reboots, reconfigure it using the GUI or the CLI.
Thankx&Regds
Saji k.s

Cisco 1040 IOS to CAPWAP possible?

I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?

Hi,
Here is the way we convert the AP from LWAPP to IOS (make sure you are using the right image), example is for 1142 AP..
The image that is on the device is LWAPP one, not the autonomous.. if you want to use the AP in autonomous mode then the image should be W7.. that is..
c1140-k9w7-tar.124-21a.JY.tar not c1140-rcvk9w8-tar.124-23c.JA.tar
I request you to do download any image from the below link and perform the conversion from LWAPP image to autonomous..
http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N
the methos to convert is..
download TFTPd32 from google and install it on ur PC.. point the image that you have downloaded in the TFTP server..
connect a ethernet cable between ur laptop and AP.. both should be in the same subnet.. and connect a console cable and get the hyperterminal console access and issue the command.. make sure you are able to ping the PC and the AP and vice versa!!
AP>en
AP#debug lwapp console cli or debug capwap console cli
AP#config t
AP(confg)int fa 0
AP(confg-if)ip addr (same subnet as that of the laptop)
AP(confg-if)end
AP#archieve download-sw /force-reload /overwrite tftp:///
AP#archieve download-sw /force-reload /overwrite tftp://<10.0.0.5>/c1140-k9w7-tar.124-21a.JY.tar
The above command will do it for you!!
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Steps to convert access point from LightWeight mode to Autonomous mode

I need steps to convert the following access point from Lightweight mode to Autonomous mode
AIR-AP1242AG-E-K9
Regards,
Majid

Hi Majid,
The method is just hidden a little further down the doc that Scott linked (+5 points Scott :)
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Hope this helps!
Rob

Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode

Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
executing...
At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!

Hi Jeffrey,
Reverting the Access Point Back to Autonomous Mode
Have a look at Step 3
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

1130AG convert lwapp to ios

I just got another 1130AG access point, and it came with the LWAPP flash. How can I convert it back to a regular stand alone unit? I tried breaking the boot sequence with ESC, but it did not work. help!!

Hi Nick,
Here is the documented method :)
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps and Happy Holidays!
Rob

LWAPP migration question

We have migrated some 1242 APs to LWAPP.
They work fine, but when using the Aironet Site survey tool, the AP name & IP Address is not displayed. This is different to the autonomous APs that have not yet been converted. This is not a serious issue, but we would like to know if this can be configured via the WLC or not.
thanks
Colin

Hi RN,
Here is the method :)
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

1131AG CLI commands

I am attempting to reset an ap to its defaults. I can get into the cli, but the "wr erase" command is not available. How do I erase the config on this ap?
Also, I originally configured the ap to connect to wlc 4400, which worked great, but when attempting to reconfigure the IP address from the CLI is not an option as the command is disabled.
How do I view the running-config on the ap?
Can this ap be used as a standalone ap?
Thanks in advance.

Hi Carlos,
Once the AP has been coverted to LWAPP (to work with the WLC) the ability to use the CLI is primarily lost. Here is the method to revert back to Autonomous (so it can be used as stand-alone);
Reverting the Access Point Back to Autonomous Mode
It is possible to revert an LWAPP-enabled Cisco Aironet access point back to autonomous mode. Please refer to Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode for detailed instructions on reverting to autonomous mode. Use this URL
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Here is the CLI info;
Manually Configuring Controller Information Using the Access Point CLI
From this doc;
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b730.html#wp1082991
Hope this helps!
Rob
Please remember to rate helpful posts.......

Configure AIR-AP1231G-A-K9 for WGB (IOS 12.4(13d)JA

Hello,
I am trying to configure one of our extra 1231 AP as a work group bridge. The AP was configured as a lightweight AP so I think that might be part of my issue.
This was the documentation I found to do the config: http://cisco.com/en/US/docs/wireless/access_point/12.4_3g_JA/configuration/guide/s43hot.html
However I do not have the commands available that they list.
Here is sh ver info:
Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 08-Feb-08 17:24 by prod_rel_team
swn-e9-wh-01-SWAP#config t
Enter configuration commands, one per line. End with CNTL/Z.
swn-e9-wh-01-SWAP(config)#int dot
swn-e9-wh-01-SWAP(config)#int dot11Radio 0
swn-e9-wh-01-SWAP(config-if)#stati?
% Unrecognized command
Is this not possible with the IOS and AP that I have?

Hi Eric,
I'm just curious, did you convert the AP back to IOS already?
This can be converted to an Autonomous/stand-alone AP that you desire;
Here is a conversion method;
Reverting the Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
Hope this helps!
Rob

Covert LWAPP AP to autonomous possible?

Similar Messages

Maybe you are looking for