Cp-8831 with uc560?

Client interested in purchasing the wireless conference phone - cp-8831 - for use with a uc560 8.6(2)... that possible?
not seeing it in the type list, but perhaps there's an equivalent that can "fake it"
thx

cp-8831 is not supported....
Below listed are the phones supported in UC560 - 8.6.2
50x-30x
51x
521-524
525
6901-6911
69xx
7906-7911
7914
7915
7916
7921
7925
7931
7936
7937
7940-7960
7941-7961
7942-7962
7945-7965
7970-7971
7975
8961
9951
9971

Similar Messages

Redundant power with UC560-T1E1-K9

Good morning,
Is there any way of having redundant power with UC560-T1E1-K9 (redundant internal power, RPS, UPS, etc..)?
Thank you very much
Best Regards
João Mendes

Hello,
In order to use Meet-Me conferencing, you have two options.
1. Conferences have to be "initiated" by an internal phone.
a) To initiate conference, pickup an internal phone handset, hit "more" button on phone menu, hit "MeetMe" option. Then dial meet-me extension (770). Now that the conference has been initiated, other phones can just dial the 770 extension to join the conference.
2. Select "Enable Meet-me Unlocked" on the CCA page for the conference configuration.
a) To initiate a conference, just dial the conference extension (770). Users can join by dialing 770 also.
Thank you,
Darren

Fax and Modem with UC560

Dear All,
I have a somewhat tricky configuration to make happen and hope you can help me.
I have a UC560-BRI-K9 (located in Germany) that is connected via BRI/ISDN and also utilizes an external SIP-Trunk.
The UC is shared by two related businesses and the Trunks are separated using COR-Lists.
I am now tasked with making both Faxes and Modems work. Via the SIP-Trunk, I only need T.38 to work for inbound and outbound faxes; no problem here. On the BRI-Port however, it is quite a different story: Here, I need both Fax and Modem working. The modem functionality is required by a Power Generator to call for maintenance in case of failure (or be called on a designated number for preventive checks). Furthermore, there also is a Postage Meter that also requires outbound modem comms.
Digging through the configuration documents, I see that the UC500-Series does not support Fax-passthrough and modem-passthrough to be enabled simultaneously as they are handled similarly.
If anyone has come across a solution for my problem, please let me know.
Thank you very much in advance!
Best regards,
Colin

If you use BRI and the fax or modem is conneceted to a FXS port in the same router, you don't need to worry about anything. It will work fine without any configuration.

Clustering with UC560/540

Hi,
Is it possible to configure UC560 and UC540s kept in different locations as Publisher and Subscribers and there by avail the centralised deployment advandages?
I have one client with one UC560 at Head office and two UC540s at two different branch offices. I wnat to configure the extension mobility feature for all the users to access their profile at any site. They got VPN over normal internet connection not a MPLS connection. Can anybody help me on this?

Sorry I meant to send this to the ejb newsgroup.
          dan
          dan benanav wrote:
          > Do any vendors provide for clustering with automatic failover of entity
          > beans? I know that WLS does not. How about Gemstone? If not is there
          > a reason why it is not possible?
          >
          > It seems to me that EJB servers should be capable of automatic failover
          > of entity beans.
          >
          > dan

SPA525G2 Not working with UC560

I have a UC560 working with a few SPA502G phones. However I can't get them to work with the 525G2. I connect the phone, assign the VLAN, and the phone gets the correct IP address from the correct subnet, and the phone is listed in the topology in CCA. But thats it... it's not listed under Configure -> Telephony -> Users and Extintions -> Users and Phones. When I try to manually add it. I don't get the eact model listed (525g2). I only get 525g. Even when I choose it, the configuraation continus fine, but with no result. The phone doesn't get an extention, nor does it work.
When troubleshooting, found the image on the phone is 7.5.2a. And when typing 'show flash' in the terminal i can see the image for this phone is 7.4.2
UC01#show flash | i phones
95           0 May 04 2010           05:00:18           phones/5x5
96     3477171 May 04 2010      05:00:30           phones/5x5/spa5x5-7-4-2.bin
97           0 May 04 2010           05:00:32           phones/525
98    10753536 May 04 2010      05:01:10           phones/525/spa525g-7-4-2.bin
99           0 May 04 2010           05:01:12           phones/521_524
100     892511 May 04 2010      05:01:16           phones/521_524/cp524g-8-1-17.bin
UC01#
Does that mean I need to upload the new phone image into UC560? how do I do that?? when I tried downloading the 7.5.2a image and in CCA try to upload it through: Maintenance->Phone Load Management, then try to upload the zip file, i get this error "Software pack is not valid for this device. Please upload the correct software pack"
I'm at these current versions
CCA: 3.2(2)
IOS: 15.0(1)XA, RELEASE SOFTWARE (fc2)
CME: 8.0
CUE: 7.1.3
525G2 firmware: 7.5.2a
Thanks

Hello,
I recommend that you take a backup of your system and upgrade the IOS and Voicemail to the latest version as per this release note. Lots of bug fixes between your release and this release. Also, you may be able to use the software download to get the latest SPA525G2 firmware.
Release Notes:
https://supportforums.cisco.com/docs/DOC-32439
Latest Software Pack for UC500 series
https://supportforums.cisco.com/docs/DOC-9829
Note. If you have not done a backup before, make sure you are using Windows XP or Windows 7 (not 8) and that you have all firewalls disabled during the upgrade.

Conference Phone 8831 with 7.1(3)

Hi,
Is there anyway to add Conference Phone 8831 to CUCM 7.1.3?
in datasheets it is only for CUCM 7.1.5+,

It depends on what CUCM you running whether it is restricted or unrestricted, you can find it with the help of below link. If CUCM is installed as restricted then you must go for restricted version (UCSInstall_UCOS_7.1.5.35901-1.sgn.iso) only.
https://supportforums.cisco.com/discussion/12079741/how-find-installed-cucm-iso-restricted-or-unrestricted
If you plan well, then it is not a difficult activity its like device pack installation just you need to switch the version after new iso installation and you dont need to reconfigure anything except frimware; if you dont want to update the firmwares then you can revert back the firmware names in device default.
Suresh

Can UC560 support CP7926

Looking to setup a UC560 in a manufacturing/warehouse environment and the CP7926 bar coding capabilities would be great; the product description states it works with Unified Communications Manager and not Manager-Express:
http://www.cisco.com/en/US/products/ps11266/index.html
Are there plans to allow 7926 to work with UC560 if it doesnt today?
thanks,
Hector

Hello Hector,
I know that the latest version on CCA does NOT include the 7926, but the latest IOS does list the 7926. So this phone should work, but would need to be configured using CLI. Also, I do not believe that the bar coding capabilities would work as the UC560 is running Call Manager Express, and not Unified Communications Manager. With the UC560, you would likely get phone capabilities only.
Thank you,
Darren

UC560 and 6900 support

Hi,
I would like to know from which release of UC560 are the 6900 IP Phones supported?
We can now select 6900 with UC560 in Quick Pricing Tool but what about existing UC560 systems?
Regards,
Carlos

Software Pack 8.1.0 with CCA 3.0.1.
All 69xx excep 6945.

Asa 5505 transparent firewall issue

hi i am having uc560 with voice and data vlan and i am having 3560 layer3 switch and my network is working fine the dhcp for voice and data both are running in uc560.
now i add asa 5505 between uc560 and switch in transparent mode means from uc560 to asa 5505 outside interface and from asa inside interface to switch,
i conigured vlan1 -- inside and vlan 2 as outside in asa 5505
in my uc 560 data is vlan 1 and my voice is vlan 100.
when i connect my network with transparent mode firewall no dhcp amd no phones are working . but if i remove asa and i connect with uc560 to switch everything is fine.
is there anyway to work multiple voice and data vlan in asa 5505 transparent mode.

hi rojas,
here is my problem,
my internet and voice all connected in the uc 560 so wat i am doing i am connecting firewall outside to uc 560 trunk port and the from inside to my switch.
when i connec to my switch it is giving message inconsistant vlan and it is port is blocked. and my phones are not working.
my data vlan1 is 192.168.123.x
and my voice vlan100 is 10.1.1.x
and the firewall ip 192.168.123.3

CUCM Device Pack - Cluster Reboot

I'm going to be adding a device pack to CUCM 8.6 to add support for the 8831, with one Pub and one Sub.
Do I need to install the device pack on both and reboot the simultaneously or in order such that:
Install on Pub
Reboot Pub
Install on Sub
Reboot Sub

As a side note on Terry's post. If you want to keep your current firmware loads after the reboot make sure you annotate other devices and what they were using. Some people prefer to keep their old phone loads while using the new device pack just for the 8831s or whatever other new devices they are installing.

AIR-E-K9 LAP521G error

Hello,
I have a wifi access point AIR-E-K9 LAP521G.
Is it compatible with UC560.
Or do we need a AP521G?
Nicolas

Yes, the AIR-LAP521G-E-K9 is compatible with the UC500 series. However, the AIR-LAP521G-E-K9 is not a standalone access point and cannot be deployed without the AIR-WLC526-K9 controller. The AIR-AP521G-E-K9 is the standalone version, and it is also compatible with the UC500 series.
Both the AIR-AP521G-E-K9 and AIR-LAP521G-E-K9 have been discontinued and have been replaced by the AP541N-E-K9 model. The AP541N-E-K9 is a standalone AP that is capable of clustering without the need for a wireless controller. The AP541N-E-K9 can be managed by CCA 2.2 and later.

CP8831 Wireless Microphone Volume

I recently installed a new CP-8831 with two wireless microphones. Everything works perfect except that callers on the other end report that it is hard to hear me until I literally hold one of the wireless microphones up in front of my mouth. Is there any way to increase the volume on the microphones?
Using sip8831.9-3-3-5.

Someone has posted this http://community.skype.com/t5/Windows-desktop-client/Help-Windows-10-Microphone-not-working/m-p/4076999#M361092 Please let us know if this fixed the microphone for you

UC560 and 8831 device

I have a UC560 which is EOL, along with a 7937 which is also EOL. Is there sw available to add a 8831 to the UC560 or am I simply out of luck.

Hi Ronco,
You're out of luck. Cisco 8831 is not supported on UC560. You can buy a ThirdParty Conference SIP Phone to register it on UC560.
Regards

UC560 T1E1 with Direct TCP SIP

Hi,
Firstly I am new to cisco's voice setup, and have a UC560-T1E1-K9 which I need to configure as just a basic gateway. Essentially i want to setup trunk-to-trunk between ISDN PRI and TCP SIP but do not have the first idea where to start.
The main aim is to receive calls over ISDN PRI (E1 NET5) and pass the call stright through to a direct tcp sip trunk (incoming only).
Then configure FXS for a few numbers for two way calling.
Hope someone can give me a couple of pointers as the CUE is not very helpful
Thanks,
Alex.

Hi,
You have two approaches.
Option A
Use CCA to configure the unit from scratch. Configure the unit for your ISDN connection and test using the fxs ports. Manually configure a SIP dial-peer to route inbound PSTN calls to your Lync server. You'll need to tweak the configuration at various places to make it work. You therefore need to be pretty confident in understanding all the work CCA has done for you. The benefit this, is you have a local outbound dial-plan pre-configured on the unit.
Option B
Configure the unit yourself from scratch. Rough outline:
1. Configure E1 controller for voice
2. Setup the DSP modules for your region
3. configure a pots inbound dial peer to accept calls from the PSTN
4. configure an outbound SIP dial-peer to send the calls to Lync.
Lync expects calls to be prefixed with a + & E.164 and bare in mind the telco may only send you the last 6 sigits of the called number
Here's an example for UK ISDN with 30 timeslots: note module slots will be incorrect in this code, example is generic IOS and not specific to UC560.
1. Configure E1 controller for voice
card type e1 0
network-clock-participate wic 0 ! something like this, you may need to work out which slot you have
network-clock-participate slot 1 ! or something like this
network-clock-select 5 E1 1/0 ! you get the idea....
controller E1 1/0
pri-group timeslots 1-31
interface Serial1/0:15 ! do a show run to check the right interface slot number
description "use dial-peer voice 10 to reach me for outbound"
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn timer T309 400000
isdn incoming-voice modem
isdn T309-enable
isdn send-alerting
isdn sending-complete
no cdp enable
Your E1 card should now be up
c2821.1.hex#show controllers e1
E1 1/0 is up.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20090408, FPGA: 13, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (652 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
2. Setup the DSP modules for your region
voice-port 1/0:15
cptone GB
bearer-cap Speech
3. configure a pots inbound dial peer to accept calls from the PSTN
I suggest at this point, you debug isdn q931 and dial in. See how many digits the telco sends you.
Configure a number translation to put this number in to E.164
In my example we take the 6 digits the telco sends us and prepend 441234
voice translation-rule 10
rule 1 /^$.+$$/ /441234\1/
voice translation-profile incomingisdn
translate called 10
in exec mode:
SOV_TAG1#test voice translation-rule 10 567890
Matched with rule 1
Original number: 567890 Translated number: 441234567890
Original number type: none      Translated number type: none
Original number plan: none      Translated number plan: none
dial-peer voice 1000 pots
description Inbound POTS dial-peer
translation-profile incoming incomingisdn
incoming called-number .+
direct-inward-dial
port 1/0:15
4. configure an outbound SIP dial-peer to send the calls to Lync. Lync expects calls to be prefixed with a + & E.164 so we're going to add a plus
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729r8
codec preference 4 g729br8
voice translation-rule 20
rule 1 /$.+$/ /+\1/
voice translation-profile addaplus
translate called 20
in exec mode
#test voice translation-rule 20 123
Matched with rule 1
Original number: 123    Translated number: +123
dial-peer voice 1010 voip
description SIP Trunk to Lync
translation-profile outgoing addaplus
preference 5
destination-pattern ^441234.+ ! note this is the area code we added to make the number into E164
voice-class codec 1
voice-class sip outbound-proxy ipv4:192.168.10.10 ! ip address of lync
session target dns:lync.mydomain.net ! your lync realm
session protocol sipv2
session transport tcp
dtmf-relay rtp-nte
no vad
and that's about it apart from getting the fx0 ports sorted - one step at a time.
For outbound you added an incoming SIP dial-peer and an outgoing pots dial peer.
Adam
VoIP.co.uk

Cisco 3650 not working with Cisco 8831 Conference IP phone

hi all,
i'm not a fan of 3650 switch as it's giving me problems.
the 3650 can CDP and HTTP to 8831 but CUCM says "not registered."
the 8831 works fine with 3560 and can register to our CUCM.
just want to know if 3650 supports 8831?
can't seem to see any docu or links.

I have the same issue, changed the 3650 IOS-XE to many versions with no luck.

Cp-8831 with uc560?

Similar Messages

Maybe you are looking for