CP1500 CPCI Motherboard Requires COM connection

I am using a CP1500 - 440MHz motherboard in a CPCI system. For the system to start it always requires a COM cable connection to a PC running a Serial Terminal Emulation program. When the system is booted up, if the COM connection is removed by either removing the cable or exiting the Serial Terminal Emulation program the CP1500 system crashes. The system will not boot up without the COM cable connected with the Serial Terminal Emulation program running. Another system I have does not need the COM cable connection running to start up. It is not the hardware at fault. Does any one know if there is a file within Solaris 2.6 or 8 that states that the COM cable must be connected to a Serial Terminal Emulation program for the system to run?
Thanks
Ryan

Normally no terminal is required for a system to boot unless "auto-boot? false". This would require you to have to type "boot" at the ok prompt. Thus you would be required to have some type of input device to type. At the ok prompt type printenv auto-boot? If it comes back false then you should type setenv auto-boot? true to change it. Then type reset to lock it in to NVRAM. You may also want to investigate the kbd -a enable / disable command while you are unpluging your laptop. Some have found that killing Hyperterm while still plugged in causes a break to be sent and the system goes to the ok prompt. They pull the cable first and they kill it. Your results may vary. The kbd -a command allows you enable or disable the abort (break, Stop +a) to the system while you are connecting or disconnecting cables to the serial port. You may want to experiment with this as well.

Similar Messages

Widgets that require web connection not working

Hello,
I have an ongoing issue where widgets that I download that require web connection seem to have trouble doing their job, I recently switched from Safari to Firefox could this have anything to do with it.
More specifically it's an i-tunes album art widget that is not working, is it an itunes upgrade thing?
Thanking you all in advance for any suggestions.

Hi, I doubt it's FF vs. Safari issue myself.
Give this a try & report results please.
Try putting these numbers in Network>TCP/IP>DNS Servers for the Interface you're using...
208.67.222.222
208.67.220.220
Then Apply. These are safer/faster than most ISP's DNS numbers, and have been patched against DNS poisoning.
https://www.opendns.com/homenetwork/start/device/apple-osx-tiger
DNS Servers are a bit like Phone books where you look up a name and it gives you the phone number, in our case, you put in apple.com and it comes back with 17.149.160.49 behind the scenes.
Problems are that many Modems/Routers don't communicate the DNS Servers with macs all that well because they've made mistakes in their Firmware & by golly by gee, they tell MS about the workaround!
Then, many... even major ISPs have DNS problems and may have not even patched them against DNS poisoning!

Windows Intune Subsription Problem - Configuration required to connect to Windows Intune Service

Hi,
Has anyone come across this description message before : Configuration required to connect to Windows Intune Service?
I've added an Intune Service to my Site, but I've got the above message.
I'm not exactly sure what it means.
Can someone help.
Maybe I've not done something that I need too.
Thanks

Windows Intune Service is a component of SCCM. If you have not added Windows Intune Subscription, the component will not be installed. Check the Component Status in Monitor Node.
Sitecomp.log is a log that records the installation activities.
Juke Chou
TechNet Community Support

I am connected to my usual wifi and when I try to go onto any apps which require internet connection, it says I have no internet connection yet I am connected to wifi, how do I resolve this?

I am connected to my usual wifi and when I try to go onto any app's which require Internet connection, it says I have no Internet connection yet I am connected to wifi, how do I resolve this?I have had this problem for about a week.
Any responses are appriciated

You posted in the iPad forum, but you profile lists an iPhone 4S. Does your iPhone or iPad have this problem.
Here's some iPad suggestions. Most also apply to the iPhone. Your iPhone or iPad may show the wifi symbol but that only shows the presence of a wifi signal. Not that you are connected.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

"Network service error" game apps that require internet connection working fine, internet signal strong. Safari working, but YouTube, Facebook, Twitter and App Store won't work?! Tried resetting network settings but problem persists?

Safari working fine, as are game apps that require internet connection.
I can not get AppStore, YouTube app, Facebook app or twitter app to load anything as 'network service error" comes up.
I have the latest update 7.2 and have tried resetting network settings, anyone else have this problem?! How do I fix it?

I did try that one. But for some reason it still does not help. The strange thing stays that I can acces Twitter and other Apps. But still nos Safari/App Store. Only when I am on Wi-Fi.

Flashcards require multiple connection attempts before recognized

I have an early 2008 MBP, a SanDisk USB card reader, and a Sandisk Firewire 800 card reader.
When I connect flashcards from any camera, it requires multiple connection attempts before it is recognized by Finder or Disk Manager. I'm using multiple cards, formatted by three cameras. Because Disk Manager doesn't show the card, I have no choice but either disconnect the flash card reader, or insert the card.
Although this occasionally happens with USB, it always happens with Firewire. I can sometimes reinsert the card three times, but unplugging the firewire cable (or USB) at the computer seems to be the most successful.
Once recognized, the cards work flawlessly. I've run disk repair and repair permissions multiple times on my drive and flash drives, but somehow, I don't think that is the issue.
Any ideas?

My apologies. I'll answer your questions to clarify.
eww wrote:
Your message is unclear. First, I don't know of anything called Disk Manager. What is it?
Disk Utility, not disk manager. If I connect the card reader and insert a card, and the card's volume does not appear in finder, the card's volume also does not show in Disk Utility.
eww wrote:
Disconnecting the reader is clear enough, but how is your computer to read your card if you haven't already inserted it? Do you mean "remove the card"?
Have you tried connecting the reader with a card in it and merely waiting for it to be recognized? Particularly if it's a very high-capacity card, reading its contents may take a little while before the card's icon appears on the desktop.
I didn't connect the dots. If the card it not recognized the first time, then I either I disconnect and reconnect the card reader, or remove the card and reinsert the card. This will usually allow the card to be seen.
I have 16GB cards. I do wait on the first connection attempt. I usually insert the card, then connect the card reader. I'll come back minutes later to discover it was not recognized. However, I will be more patient retrying the connection next time. I usually wait 10-15 seconds before trying a second or third reconnection attempt.

What are the Trading Card Games for iPod touch that doesn't requires Internet connection?

What are the Trading Card Games for iPod touch that doesn't requires Internet connection? Suggestions, please.

Why not look at the apps and fine out?
The odds of someone here knowing that are slim to none.

Tell me about an application of world map that doesn't require internet connection, Nor GPS

I need good & updated maps that do not require internet connection .Do you know @ an application ?

Have you tried searching the app store or doing a google search?
In the time it took you to register here and post your question, you could have already found an answer.

Every app on my ipod (2nd gen) which requires wifi connection doesn't work although the wifi mark is on. i did try restarting my ipod, resetting network setting, disconnect from wifi and reconnected it but non of them worked.

every app on my ipod (2nd gen) which requires wifi connection doesn't work although the wifi mark is on. i did try restarting my ipod, resetting network setting, disconnect from wifi and reconnected it but non of them worked.

This may sound silly but try your date a time setting my ipod had the same problem and i had even checked the the date and time went all the way to the apple store for help and the genius guy just rest the date and time and it worked just fine.

Error running XL Reporter: 'a required COM add-in program..' for Excel 2007

I have 2 users running Excel 2007 that can't run XL reporter. They get the message 'a required COM add-in program for XL Reporter has not been loaded'. I have instructions for Excel 2003, but not for 2007. Does anyone know how to resolve this for Excel 2007?

Gordon,
I have instructions to get the IXXLReporter.dll file in the installation area, but 2007 has completely different layout. I can't find where to go??? Can you please give me the procedure?
Edited by: Pat Frohlich on Apr 1, 2009 10:12 AM

Required COM add-in program for XL Reporter

Hi everyone,
Is SBO 2007A XL Reporter compatible with MS-EXCEL 2007? How can I configure the settings if the system would prompt a message "A required COM add-in program for XL Reporter has not been loaded and prohibits MS -Excel from running"
Thanks in advance...
Malu

Hi,
SOLUTION FOR THE PROBLEM:
Reason and Prerequisites
You need to be an administrator on the local machine to add COM add-ins.
Solution
The user should be added as a member of the administrator role on the
local computer the first time you start Excel from XL Reporter the first
time so that the COM addin are registered, then you can remove the user
from the administrator group again.
Manually Loading the XL Reporter Excel COM Add-In
Symptom
If you install Microsoft Office after installing the XL Reporter
application or use another Windows user than the one you used when
installing XL Reporter, you can get an error message.
Reason and Prerequisites
The reason for this is that the report writer COM Add-in has not been
loaded, which prohibits Microsoft Excel from running.
Solution
1. Start Microsoft Excel. If you already have the COM Add-ins command on
the Tools menu, go to step 7.
2. In the Tools menu, choose Customize.
This opens the Customize window.
3. Choose the Commands tab and select Tools from the Categories pane on
the left.
4. In the Command pane on the right, scroll down to the COM Add-ins
command.
5. Select the COM Add-ins command, hold down the mouse button, and drag
COM Add-ins from the Commands pane over to the Tools menu on the Microsoft
Excel men bar. When the Tools menu commands appear, point to where you
want the COM Add-ins command to appear on the menu and release the mouse
button.
6. To close the Customize window, choose Close.
7. On the Tools menu, choose the new COM Add-ins option.
This opens the COM Add-ins window.
8. In the window, choose Add to open the Add Add-in window.
9.Select the IXXLReporter.dll file located in the Client directory in the
XL Reporter program installation area and choose OK.
10. In the COM Add-ins window, select the XL Reporter checkbox and choose
OK.
Note: This is only a link from SAP Business One Reporting and Printing Forum. Cant paste the forum no.
Regards,
Clint

A Required COM Add-in program for XL Reporter has not been loaded and ....

A Required COM Add-in program for XL Reporter has not been loaded and prohibits Microsoft Excel from running. For more information, click help.
XL 2007, with the Trust level for macros set to minimum. SBO 2007 PL 42.
Thanks
Charles

Read the following solution from SAP for your problem:
When we open XL Reporter we get an error
message "A required COM add-in program for XL Reporter has not been loaded
and prohibits Microsoft Excel from running." when trying to open a report
definition.
SOLUTION FOR THE PROBLEM:
Reason and Prerequisites
You need to be an administrator on the local machine to add COM add-ins.
Solution
The user should be added as a member of the administrator role on the
local computer the first time you start Excel from XL Reporter the first
time so that the COM addin are registered, then you can remove the user
from the administrator group again.
Manually Loading the XL Reporter Excel COM Add-In
Symptom
If you install Microsoft Office after installing the XL Reporter
application or use another Windows user than the one you used when
installing XL Reporter, you can get an error message.
Reason and Prerequisites
The reason for this is that the report writer COM Add-in has not been
loaded, which prohibits Microsoft Excel from running.
Solution
1. Start Microsoft Excel. If you already have the COM Add-ins command on
the Tools menu, go to step 7.
2. In the Tools menu, choose Customize.
This opens the Customize window.
3. Choose the Commands tab and select Tools from the Categories pane on
the left.
4. In the Command pane on the right, scroll down to the COM Add-ins
command.
5. Select the COM Add-ins command, hold down the mouse button, and drag
COM Add-ins from the Commands pane over to the Tools menu on the Microsoft
Excel men bar. When the Tools menu commands appear, point to where you
want the COM Add-ins command to appear on the menu and release the mouse
button.
6. To close the Customize window, choose Close.
7. On the Tools menu, choose the new COM Add-ins option.
This opens the COM Add-ins window.
8. In the window, choose Add to open the Add Add-in window.
9.Select the IXXLReporter.dll file located in the Client directory in the
XL Reporter program installation area and choose OK.
10. In the COM Add-ins window, select the XL Reporter checkbox and choose
OK.

ME SDK 8.0 EA Device Manager - Problems with Serial COM-Connection

I caught a first glimpse at the new ME SDK 8.0 - so far I have been working only with very old JavaME-Stuff on a Cinterion-TC65i-Chip.
Want to connect my Raspberry Pi via serial COM-Connection with the SDK-8.0-EA-Device-Manager. (due to security reasons I'm not allowed to connect the Pi via LAN/Wifi)
But the problem is the ME SDK 8.0 EA Device Manager only offers me COM4 (this is my built-in UMTS-Modem) - even though my target-COM-Device isn't busy at all.
A serial connection via Putty and USB2Serial-Cabel (FTDDI) works fine and I can get on my Raspberry.
Is there any reason or restriction I don't know for being unable to use my dedicated COM-Port? Or do I have to make any additional adjustments in hidden SDK-Property-files?
In my opinion the device manager using COM should offer me the same possibilities as an IP-Connection regarding the target-device (transfering my Jad/jar to the device, installing them and starting them).
There is something in the SDK-get-Started Docu about "Connecting to a UART Device" I'm not really cotton on . Is this information concerning me even though I'm using a Raspberry PI?
To put my files manually via USB-Stick or Z-Modem on the PI is a tad of inconvinient.
Any ideas? Or am I completely off track understanding your SDK-Tooling?
Thx and best regards

Hi,
For the Raspberry Pi, tooling over serial port is not supported. The simplest solution is to use standard IP networking over Ethernet. This can be a direct connection between the PC and the Raspberry Pi, as long as the cable is twisted and the IP addressing is correct (e.g. manual IP addressing or DHCP server on the PC).
Regarding "Connecting to a UART Device": This is meant for attaching and controlling serial devices from the Raspberry Pi, not for tooling connections between the Raspberry Pi and the PC.
Hope this helps,
-- Terrence

I am attending an on-line webinar i 1-hour. Their site requires Adobe Connect Add-in. I have installed this, however their site it cannot find it. Please advise

I am attending an on-line webinar 1-hour. Their site requires Adobe Connect Add-in. I have installed this, however their site it cannot find it. Please advise

The add-in should only be required if you are sharing your screen or uploading PPTX content.
Are you having trouble with the room loading? Can you explain/show the issue you are having?

WRT110 and Vista SP1 - additional log on information is required to connect to this network...

Setup WEP 64bit . WinXP SP3 and iPod Touch connect fine but when I select the SSID via Vista it doesn't give the network option. How can I get the network propt option to appear.
[img]http://www.auburn.edu/oit/connectivity/wireless/images/new_connectionsVista10.jpg[/img]
"additional log on information is required to connect to this network
You may need to select a certificate or enter a user name and password to connect to this network."
[img]http://www.auburn.edu/oit/connectivity/wireless/images/new_connectionsVista11.jpg[/img]
I updated to the lastest firmware with no luck.
Using WRT110 firmware Ver. 1.0.04 (build 10).

toomanydonuts let me clarify again:
-XP SP3 desktop = able to connect.
-iPod Touch = able to connect.
New Vista SP1 laptop = NOT able to connect and DO NOT get a prompt to enter a Network Key. Instead I get:
"additional log on information is required to connect to this network
You may need to select a certificate or enter a user name and password to connect to this network."
here is an example screen shot of the above message (found on another web site).
http://www.auburn.edu/oit/connectivity/wireless/images/new_connectionsVista11.jpg
Then Vista SP1 as me to enter a user name/password/domain. This is a home network.
http://www.auburn.edu/oit/connectivity/wireless/images/new_connectionsVista12.jpg
No prompt for Network Key (on VISTA SP1).
My WRT110 is running the lastest firmware Ver. 1.0.04 (build 10).
Message Edited by FerociousLS on 02-04-2009 04:45 AM
Message Edited by FerociousLS on 02-04-2009 04:46 AM
Message Edited by FerociousLS on 02-04-2009 04:47 AM

CP1500 CPCI Motherboard Requires COM connection

Similar Messages

Maybe you are looking for