CP2025 printing with heavier stock

I have a new Color LaserJet CP2025dn, and wonder whether I still have to open the back door when I print on card or photo stock so that the paper doesn't get curled as I did on my earlier LaserJet 2200.

The rear door on this printer is for accessing the duplex path- there is no straight through path which is used for heavy stock. All weights are output to the top output tray.

Similar Messages

Pro9000 Prints with Heavy Blue Cast

Hello all!
I have several Canon Pro9000 and Pro9000 Mark II printers. The Pro9000 Mark II printers are doing great. However, the Pro9000 printer is printing photos with a heavy blue cast to them. The blue is so heavy and so bad that any photo printed with it is destroyed.
I have tried printing both from Photoshop and from other programs, including straight from Window's photo viewer. When printing from Photoshop, I have tried both letting Photoshop manage colors and the printer manage colors. When Photoshop is managing colors, I've turn color management off for the printer (set it to None). I've made sure I have the proper paper selected, etc. It does not matter what I do, the Pro9000 still prints with a heavy blue cast.
I've tried switching from Auto to Manual in an attempt to reduce the blue. But even if I have the first slider (labeled Cyan) slid all the way to the red side and the third slider (labeled Yellow) slid all the way over to yellow, I am still getting a heavy blue, but now the images are too red and too yellow, etc.
What can I do to figure out what is going on with this printer? It used to print properly, so I am not sure what changed. Any help would be much appreciated.
Thank you.
PS - I am running Windows 8.1, 64-bit.
Solved!
Go to Solution.

I don't have any 9500's. I have two Pro9000's and four Pro9000 Mark II's. The Mark II's all print fine from the same computer(s). Both of the Pro9000's (non-Mark II) are printing with the heavy blue tint.
The monitor being right should not be an issue here. After all, what I see is what I get with the Pro9000 Mark II's.
I've tried both letting Photoshop handle all the color profiling and letting the printer do it. I get the same blue tinting. Just FYI - I cannot always use Photoshop to print. I do event photos where I am using a Hot Folder for printing. In cases like this, Photoshop is not even running. That's when I need the printer to handle color profiling (the hot folder software I currently use has not control over this). Again, this works fine with the Pro9000 Mark II's.
I've played with numerous settings and nothing is removing the blue tinting. I thought it might be the print heads, but the check nozzle pattern looks like it is printing just fine. This is why I am confused.

HP Color Laserjet CP2025 printing with a 'shadow' effect

Hi All
My printer is printing some documents with a pink 'shadow' type effect on font (various different ones) and even an image I have inserted.
If I print a test page I don't get this, yet documents I have saved as a template and have been using since I got the printer have always been ok up until today.
My printer is only approx 4mths old. Toner levels are ok (half or over). I have turned off, re-calibrated, & also re-calibrated the colours but still a problem.
Any ideas?
I should add if I send the document/s to a different printer (an Officejet) I don't get this problem, but I prefer to print these on the Laserjet due to quality

Thanks Steve
I've had a look at the Manual and it refers me to using the HP ToolboxFX - this I don't have on my computer.
I am running WIndows 7 and the cd that came with the printer wouldn't install.
I am trying to find this HP ToolboxFX on HP's ite but no luck and as for trying to contact them, I have to jump so many hoops only to find they don't have my model on their list before you can send them an email grrrr
Anybody able to send me a link for this HPToolboxFX? I presume it should be available??

1099 2010 Forms Print with heavy black line down the right hand side

Greetings,
When we print the 1099 2010 Mscellaneous Income form we have this heavy black line that goes down the right hand side of the margin. We already applied all notes for 2010, including the latest one that had the margin correction published on 1/21/2011.
Anyw

Ours print that way, too. The black line is in the 1099MISC_2010.bmp image that SAP provided in the note. The image is used as the background for the forms.
Regards,
Shannon

OfficeJet Pro 8000 no borderless printing on card stock via Windows driver

I just setup the OfficeJet Pro 8000 wireless printer the other day with the intent to print borderless cards on card stock. I can print anything to it without issue however if I attempt to use borderless mode the Windows driver does NOT allow any paper type other than photo or glossy borchure types.
If I print anyway on card stock it looks ink soaked and muddy. If I print on their recommeded types it looks fine but a card needs heavy card stock, not med or light paper weights.
If I do not select borderless, the print (on card stock) has a dredded border but the print quality is fine.
The driver will not allow even a "normal" or "draft" borderless on standard paper types. Is there a hack or modification to allow me to print borderless on any paper?

Hello,
Please click HERE to access the steps that should resolve the issue.
You may have to try Solution Three .
. If issue still persists, please call HP Tech Support for further assistance.
If you are in US , the toll free # is 1-800-474-6836 .
If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.
Regards,
Jabzi
Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

HP Color LaserJet CP2025 Printer - Vertical Yellow Band printing on every page

For the last several weeks whenever I print from my HP Color LaserJet CP2025 Printer the pages print with a vertical yellow band on the right hand side of each page. I checked the supplies status and it says each ink cartridge has plenty of ink left so I'm at a loss as to what could be causing this yellow band. I'm wondering if it has something to do with the printer's hardware (inside roller perhaps)?
Any insight would be most appreciated.

Hi there cdyson44, Welcome to the Forums!
To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at: http://h30499.www3.hp.com/t5/Printing-and-Digital Imaging/ct-p/bsc-412
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

How do I get an Office Jet 6500A to print on Card stock?

How do I get an Office Jet 6500A to print on card stock. It pushes the card stock through the printer but will not print and tells me I have not selected the right print media. There is no selection for card stock. I have tried every selection. I assume there are other media definitions that can be downloaded but they certainly are not apparent. I have been doing this job on all my other HP printers for years. Suddenly this printer balks.

Hi,
Page #22 of the manual says (must be the same as photo paper ?):
To load cards and photo paper
1. Lift the output tray.
2. Slide the paper width guide out as far as possible.
3. Insert the media print-side down along the right of the main tray. Make sure the media aligns with the right and back edges of the tray and does not exceed the line marking in the tray. If the photo paper has a tab along one edge, make sure the tab is pointing towards the front of the printer.
4. Slide the media guides in the tray to adjust them for the media size that you have loaded.
5. Lower the output tray.
6. Pull out the tray extender.
And the manual is : h10032.www1.hp.com/ctg/Manual/c02519721.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Poor quality printing with quick books remote

I just started using the HP 8610 and now the print quality is poor when remote printing from quick books. It was perfectly fine wiht my OLD OLD HP 1200. checked with remote printing company and they have not helped. Any clues?

I have the same problem when using Logmein with my new 8610. Printing text heavy statements from remote computers that look fine on the screen, come out with fuzzy pics and pixelated words. This was also never a problem with our old 7510.

PRINTING ON CARD STOCK

When attempting to print on card stock paper, the LJ 6500 ejects the (blank) card stock paper and then prints on the second page. Yes, I know...put the card stock as the second page. But, I would like to know why the AIO ejects the first page. The driver that I am using is a E710A-F.
Your thoughts?

rak1up,
This article covers issues with blank pages:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01892627&cc=us&dlc=en&lc=en
Give the steps listed under your operating system a try and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Printing with EPSON - SRGB

I have been printing in PS for years and now I must admit after being away from it all for a while I am lost......
I started shooting portraits for head shots in SRGB because when they were RGB 1998 the folks who took them to other print shops for duplicates got bad results. At that time I learned that most commercial printers are SRGB shops and I needed to switch.
Now however when I recently shot in srgb and tried to print for myself, shooting a canon 7d in standard mode, srgb, I found a very lackluster color in my headshots....still pretty but not as rich as I expected.....kind of grey.....
Then of course I tried to print on my EPSON 3800 which has always printed dark...After finishing in LR I would always print out of PS, because there have always been a few final touches I want to make.....however, the prints that are pushed to what I would consider the max in LR
as far as brightness is concerned would always need an extra push almost into clipping in PS to get a good print.......
This week I added a Epson Artison 1430 as an extra printer for small work (My Grandchildren 3x5's) and as long as I let the printer manage colors it prints fine, otherwise a bit red....Arrrrggggg!
I really need some help getting things straight so I can get some consistency.....the reading I have always done says NEVER use printer management always use PS to manage colors, and yet I waste 2 prints for every one I get and loads of ink to get a finished product I like, and have for years, I guess I just got used to it.,....Maybe it's an epson plot to sell more ink....
So Color space confuses me, having to push a photo in levels too hot to get a good print frustrates me, and what I really want to do is go back to RGB......
Any suggestions........Use a DEll Ultra Sharp monitor....not calibrated.....

When you installed your Epson drivers they should have also installed the ICC profiles for that printer, in a bunch of different versions for Epson's own paper stock (glossy, photo, matte, etc.). Out of the box LR doesn't list them - in the Lightroom Print module, go down to Print Job, Color Management, and in the profile dropdown choose "Other..." - it'll open your ICC folder and let you activate the Epson-specific ones. Do not choose "managed by printer".
The profiles assume Epson ink and paper - there will be a difference with off-brand paper or off-brand ink. The only way to fix that is to invest in a print profiler unit and make your own ICC files. Paper choice makes more of a difference than people think, especially to dark tones.
The intent (perceptual vs relative) will have a subtle effect on images with vivid colors, but most people won't notice. Pick what you like the look of and stick with it.
Click "Printer..." and then "Properties..." to open the Epson driver panel - on the Advanced tab, choose Color management = ICM then tick "Off" - you don't want the printer making any color adjustments whatsoever, as that's what the ICC profile is doing. For reasons best known to Epson you can only get at this "Off" checkbox in ICM mode.
Printing with that setup will give accurate color rendering, but as elie-d says if your monitor isn't calibrated what you see on screen is likely to have a horrendous color cast, so you're comparing apples and oranges. Even with a calibrated display, you either have to work with your monitor brightness turned down as low as it'll go, or view the prints outside under full sun. Indoors, prints that look OK would have to be much lighter than a calibration would make them.

Movement type 313 and 315 with Special stock indicator Q requirment

Hi Gurus,
We have the business requirement to use the Mvt 313 and 315 with special stock Q (two step stock transport for storage Location to storage location transfer). But when we are trying to use the t-code MB1B with MVt 313 with Q its not available. We know its because of SAP standard.
Also we suggested to use the Mvt 411 Q but users wants the 313 /315 with Q from moving the project stock by storage location to storage location and received the update as below.
We have looked into the option of transferring the project stock to plant stock. Unfortunately, as well as being transaction-heavy and prone to manual errors, this has accounting implications. So, we need to be able to action the two-step transfer on project stock via the enhancement described in the SAP documentation.
http://help.sap.com/saphelp_rc10/helpdata/en/0f/03df3a89ec880ee10000000a114084/frameset.htm
The link is specific to PM config . Could any one can suggest me how to handle this one to do with 313 and 315 with special stock type Project (Q) to transfer the stock by two step transfer.
Thanks,
Sada

It seems you have to activate business function set LOG_EAM_ROTSUB (transaction SFW5). After that the customizing node will be available:
SPRO > Plant Maintenance and Customer Service > Maintenance and Service Processing > Maintenance and Service Orders > Functions and Settings for Order Types > Goods Movements for Order > Movement Types for PM/CS Orders
(transaction: DI_0MVTPM)
http://help.sap.com/erp2005_ehp_04/helpdata/en/a0/00e93a2876a81ae10000000a11402f/frameset.htm
Edited by: Csaba Szommer on Jan 10, 2012 11:39 AM

Designjet 130 printer with Epson paper?

Anyone tried printing with a Designjet 130 printer on Epson paper stock? The reason I ask is I'm considering replacing my Epson 4000 with a Designjet 130r and still have a lot of Epson paper stock on hand. I guess I'd be on my own as far as developing the ICC profiles for the various paper types. Money is tight and I hate to waste the paper, on the other hand I don't want to spend any more money on ink for the 4000, most of which ends up in the maintenance tank due to constant pen clogs and cleaning cycles.

This forum is focused on consumer level products. For the Designjet you may have better results posting in the HP Enterprise Designjet forum here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

CP2025 printer - stripes across page

Hi, I have a HP Laserjet CP2025 printer that I've used for 1 year. I'm connecting via network and am running XP.
Every once in a while, my pages will print out with black, yellow, cyan, magenta stripes that run horizontally across the page. This happens to a few other computers that are running XP, 7, OS X.
This has happened with more frequency within the past 2 months to 3 computers on the same network.
We had a tech come out to look at the printer and he couldn't find anything wrong with the printer or the inks. The inks are not HP brand but are compatible. We've been ordering their inks for 1 year for this printer and longer for the previous printer we had without any problems. The tech suggested that the problem lay in our printer drivers.
However, the newest computer running Windows 7 (is not older than 3 months old) is running into the same problem. This computer is connected directly via USB.
Thank you!

This pattern sounds like the bias that moves toner across from the cartridge to the belt is shorting out. It may be your cartridges, but several others have reported a failure of one of the drive motors. This is not a home repair if this is your problem. If you have no warranty, I have seen propmorions on the DN model that net out less than $300, and you get 4 new cartridges.

How do I use a regular printer with my iPhone?

How do I use a regular printer with my iPhone?

you can't unless it's an AirPrint enabled printer or you purchase a 3rd party app like printopia.

How can I print with the black and white cartridge only?

I am trying to print using the black and white cartridge only because magenta is out of ink but I'm getting the following error message in HP Photosmart C7200 series print dialog:
The printer is out of ink.
The following ink cartridges are empty: Magenta. Replace these ink cartridges to resume printing.
How can I print with the black and white cartridge only?
Mac OSX 10.7.3
HP Photosmart C7280 (7200 series)
This question was solved.
View Solution.

I am absolutely disgusted by this; clearly a scam from HP to make more money by selling extra ink cartridges!! I will make sure to never buy any products from the shoddy rip off merchants at HP ever again!!
You should be ashamed!!

CP2025 printing with heavier stock

Similar Messages

Maybe you are looking for