CPI1.3: WLC Configuration Archive - Failure
Good day, everybody!
I try to make Configuration Archive for Wireless Lan Controller. WLC managed without any mistaces, SNMP v3 and SSH v2 have already configured.
But, when I start Configuration Archive task and check Status in Jobs Dashboard - I always have Failure, like this:
Does anybody know why I can't normally save configuration? Thanks for advices!
In the Jobs Dashboard I choose Configuration Archive Results - Failure and see Fetch Running information:
SNMP: Failed to establish SNMP connection to 10.0.10.101 - Cause: Device is Unreachable. Check the ReadOnly community string. SNMP: Failed to establish SNMP connection to 10.0.10.101 - Cause: Device is Unreachable. Check the ReadOnly community string.
But I don't understand, why Check the ReadOnly community string? I use SNMP v3!
For example, I've successfully got Configuration Archive from c3560G by using same SNMP v3 and SSH parametres.
Does anybody have ideas?
Similar Messages
-
Configuration archive after configuration change
Hello,
I'm assuming this can work with switches, routers, and controllers. I'm running PI 2.1 and am trying to get the configuration archive functionality working. I have both of these options checked under System Settings > Configuration Archive:
:: Archive configuration out-of-box
:: Archive configuration on receiving configuration change events
On the IOS device, these settings were configured for syslog/snmp:
logging buffered 100000
no logging event link-status
logging trap notifications
logging facility local6
logging source-interface Loopback0
logging <Prime IP>
snmp-server community ***** RW 13
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host <Prime IP> version 2c *****
I do not see any syslog messages in PI under alarms/alerts and the configuration never gets archived. I haven't run tcpdump yet to determine if PI is receiving these traps but I was hoping it was something simple I was overlooking. Thanks for any assistance that can be provided.Thank you for the reply. To answer your question, yes. Community information matches with PI credentials.
I actually did get it to work yesterday. I did original testing on a 1921 router which is still not working, but when I tried configuring the same information on some switches (3750's) it worked. I thought routers would be configured the same - are there hardware limitations to this?
I look in the built-in CLI template 'Configure Logging' in PI and it only has switches and WLCs as available devices to push out to but I don't know what to make of it. -
Export Wired Device Configuration Archive in Prime 2.1
Hi,
we have prime 2.1 lifecycle with 50 node license. I'm trying export device configuration archive (not controllers), but I couldn't find any solution for this. now I found "controllers configuration backup" in the setting>background task menu, but this is for wireless devices(WLC). please help me where I should find the solution.
Kind Regards,
NedaAnyone ?
./bump -
PI2.1 : Cannot make Configuration Archive : Fetch Runing/Start Fail
Hello,
I cannot make a configuration archive with PI2.1.
I'm using PI2.1 to control WLC.
When I run Configuration archive, it says Fetch Running: "Unkown error", Fetch Startup "Unknown Error", Fetch VLAN "Unknown Error".
What should be the reason?
I can enter in the WLC, configure it from PI, but cannot make "Archive Config"
Please help.
Regards,Please check the following:
SWIM and Configuration Archives support for Devices during Cisco Prime Infrastructure releases—Table 4 outlines the devices that the software image management and configuration archives support during the various Prime Infrastructure releases.
Table 4 SWIM and Configuration Archives support for Devices during Prime Infrastructure Releases
Devices
Prime Infrastructure Releases
Cisco 4400 Wireless LAN Controller1
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco 5500 Series Wireless LAN Controllers
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco WiSM1 Controller
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco 2106 Wireless LAN Controller1
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco 2504 Wireless LAN Controller
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco 2800 and 3800 Series Integrated Services Routers
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco Flex 7500 Series Wireless LAN Controller
1.2, 1.3, 1.4, 2.0, and 2.1
Cisco 8500 Wireless LAN Controller1
1.4, 2.0, and 2.1
Cisco Virtual Wireless LAN Controller1
1.4, 2.0, and 2.1
Cisco WiSM2 Controller
Not supported
1.Prime Infrastructure 1.4 does not support SWIM in Cisco 2106/4400/8500/WiSM2/Virtual WLC.
Hope that helps. -
OCS 2007 R2 Response Group Configuration Tool Failure
Hello there.
We are bringing back to life an old OCS installation. Customer performed a clean AD reinstall and we are in the process of re-installing OCS 2007 R2. All seems to work fine, except the RGS. When accessing the web tool we get this error:
Response Group Configuration Tool Failure
An unknown error occurred. The operation cannot complete successfully. Please contact the administrator if this problem persists.
Click here to return Home.
the Event viewer for application on the FE shows:
Event code: 3005
Event message: Excepción no controlada.
Event time: 13/05/2014 12:13:01 p.m.
Event time (UTC): 13/05/2014 06:13:01 p.m.
Event ID: a74ea242095f4e8099bca266a7a5cc83
Event sequence: 8
Event occurrence: 1
Event detail code: 0
Application information:
Application domain: /LM/W3SVC/1/ROOT/Rgs-1-130444779241580315
Trust level: Full
Application Virtual Path: /Rgs
Application Path: C:\Program Files\Microsoft Office Communications Server 2007 R2\Web Components\Acd Files\
Machine name: OCSR2-FE02
Process information:
Process ID: 6504
Process name: w3wp.exe
Account name: domain\RTCComponentService
Exception information:
Exception type: COMException
Exception message:
Request information:
Request URL: https://ocspool.domain.com:443/Rgs/Deploy/Default.aspx
Request path: /Rgs/Deploy/Default.aspx
User host address: 172.16.6.32
User: domain\user
Is authenticated: True
Authentication Type: Negotiate
Thread account name: domain\RTCComponentService
Thread information:
Thread ID: 9
Thread account name: domain\RTCComponentService
Is impersonating: False
Stack trace: en System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
en System.Management.ManagementObjectCollection.ManagementObjectEnumerator.MoveNext()
en System.Management.ManagementObjectCollection.get_Count()
en Microsoft.Rtc.Acd.Management.OcsApplicationContactSetting.Select(String condition)
en Microsoft.Rtc.Acd.Web.UI.WorkflowTemplate.GetContactObject()
en Microsoft.Rtc.Acd.Web.UI.WorkflowTemplate.AddedControl(Control control, Int32 index)
en ASP.deploy_default_aspx.__BuildControl__control15(Control __ctrl)
en Microsoft.Rtc.Acd.Web.UI.TemplateHelper.InstantiateWorkflowTemplate(AcdWorkflow workflow, ITemplate template, ControlCollection controlsToAddTo, String resourceClass, String templateResourcePrefix)
en Microsoft.Rtc.Acd.Web.UI.AcdWorkflowList.CreateChildControls()
en System.Web.UI.Control.EnsureChildControls()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Control.PreRenderRecursiveInternal()
en System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
Custom event details:
on the OCS logs I have:
Unhandled exception occurred in the Response Group Service Configuration Tool. The operation could not complete successfully.
Requested URL: /Rgs/Deploy/Default.aspx
User / Host making the Request: domain\user/ 172.16.6.32
Unhandled exception: System.Web.HttpUnhandledException - Se produjo una excepción de tipo 'System.Web.HttpUnhandledException'.
Inner Exception: System.Runtime.InteropServices.COMException
Cause: An unhandled exception occurred.
Resolution:
Check the exception.
Windows server is installed in spanish, if you wonder why the mix in languages.
We have been battling with this error for the last 2 weeks. Any help is greatly appreciated!
FRHi,
Please check the configuration of the Response Group Service with the help of the link below:
http://technet.microsoft.com/en-us/library/dd441277(v=office.13).aspx
Please check the OCS components that are required to implement the Response Group Service below:
Application Server and Response Group Service
Language pack
Administrative tools
Web Components Server
Internet Information Services
Microsoft Office Communicator 2007 R2
You can try to use the workflows that you crated to validate the deployment.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Cisco PI 2.0 Configuration Archive fails Nexus 5000
Hi,
we recently upgraded Cisco PI from 1.3 to 2.0 and i thought this problem would be solved but it did not. I have added two Nexus 5548 switches that i can monitor and configure through Cisco Prime but im not able to read the running och startup config to the Configuration Archive. When i run the job i get the following error:
"fig from device: java.net.SocketTimeoutException: Read timed out"
Current NXOS: 5.2(1)N1(2a)
Before i proceed troubleshooting i just would like an answer if it should be possible to archive configs from Nexus to Cisco Prime Infrastructure?
Cheers! // Mattias AnderssonThanks for the quick reply! Well, i did some more troubleshooting and i noticed that through Ethanalyzer and inspected the telnet packets that Prime tries to set the terminal lenght and width before it shows the running-config but it fails as it is in the default role of priv-0, and therefore gets % Permission denied. So, it times out after 2,5 min.
I added these two lines and worked like a charm!
role name priv-0
rule 12 permit command terminal length *
rule 11 permit command terminal width * -
PI 2.0 configuration archive problems
Hi,
I've got 2 problems with archiving device configurations in Prime Infrastructure 2.0.
1. Configuration archive job status is Completed and Last run status is Success
Looking at Configuration archive results, I see this:
Fetch Running: Success
Fetch Startup: Success
Fetch VLAN: Unsupported operation
Fetch Modules: N/A
Archive: Success
It's a Cisco 7200 router.
Looking at its Configuration archive, I can see just the running config. Startup config is missing.
2. Configuration archive job status is Completed and Last run status is Partial-Success
Looking at Configuration archive results, I see this:
Fetch Running: Success
Fetch Startup: Success
Fetch VLAN: Unsupported operation
Fetch Modules: N/A
Archive: Error in archiving for device '3663756'
It's a Cisco 6500 FWSM.
Looking at its Configuration archive, I can't see anything, it says 'No data available'. Both running and startup configs are missing.
Do you have some ideas what is wrong here, why can't I see the configurations?I've found the reason why this is happening. In the case when startup and running configs are identical (disregarding lines like 'last configuration change', 'ntp clock-period',...), Prime doesn't show startup config under Configuration Archive, it
just shows the running config. -
Wireless Design - WLC Configuration
Soon to be working on a design for a Wireless installation across one of our buildings. The wireless survery has been completed, and we'll be installing 175 APs, across the 3 floors of the
building.
With regards to the back-end WLC setup, I have a few queries around the WLC configuration. We're looking at implementing the 4400 series of devices, and due to us having nearly 200 APs, we'll need at least 2 x 4404 or 4 x 4402 - I'm assuming its simpler to have fewer devices to make management simpler.
Also, looking at the Cisco reference material, they recommend that a 4404 can support up to 100 APs, with regards configuring the ports on the box, would I need to configure LAG across the WLC
ports in order for it to accomodate all of the Access Points. If we were to go with a scenario of using 2 x 4404 devices, would we be in a position whereby if we lost a Controller, we'd lose
all of the Access Points associated with that Controller? In order for us to have full resiliency, we'd need an additional 4404 controller for the APs to failover on too?
From a licensing perspective, we'll be purchasing a licence to cover 200 APs.
TIADo you think that the phone carrier change the Android OS kernel and removed the proxy setting option before they sell it to consumers? If it's so why would they do such thing?
As far as I'm aware, no. Phone carriers don't care about wi-fi proxy. They won't make any money if they do and they equally won't make money if they don't. This "proxy" issue came straight from the developers of the Android OS themselves. It's been highlighted since day one of the Android release. This is why some browsers have incorporated proxy settings to their application because the Android OS developers are not interested to fix this shortfall.
RE: iPhone and iPad users if you use Windows proxy server and intergrated Windows authentication is enabled the credential should not be prompted for user if it's already entered in their devices.
Unfortunately, I don't have the details with me right now but I'll try to see if I still have this information when I go back to work. -
Configure archiver to read from both redo log members
Hi, We have moved our Data Warehouse to a new SAN. The luns for the redo logs are getting hit heavily. Just trying to find out if on AIX it is possible to configure archiver so that it reads from both members, current iostat data shows reads of the redo logs are only happening against the first member of each group and none against the second member. Thanks Tom Cullen
See a recent discussion on this issue :
Redo log Doubt
Hemant K Chitale -
Cisco Prime Configuration Archive on Interface Flap
Hey All,
We've been using Cisco Prime 2.1 for a bit now and I have a question about the configuration archive based on change events. Will Cisco Prime go and attempt to perform a config backup based on an interface flap? Looking at the audit logs it appears that it does that (see attachment). Is this a default behavior and does anyone see any benefit to this? It seems like if an interface is flapping it will continuously log into the device to see if the configuration has changed.
BrianHi Brian,
I don't think configuration achieve can be triggered due to interface flap ,however if there is any change in the configuration yes PI can do the config Archive
Go to Administration > System Settings > Configuration Archive
Archive Configuration on receiving configuration change events? Check box this option
Thanks-
Afroz
***Ratings Encourages Contributors ***** -
Cisco Prime Infrastructure release 2.1 configuration archiving on CISCO WiSM2
Hi all,
Just wondering Cisco Prime Infrastructure release 2-1 support configuration archiving on CISCO WiSM2?
CISCO release 2.0 mentioned that it doesn't support configuration archiving for WiSM2 but release 2.1 doesn't mention anything on it.
Please assist.No, it is not supported even for PI 2.1
-
Cisco Prime Infrastructure Scheduled Configuration Archive not executing
We have a deployment of Cisco Prime Infrastrcuture 1.3 (1.3.0.20).
Configuration Archive is a feature that collects and archives the device configurations i.e. cisco switches.
You have an option to schedule this to run, say daily, weekly etc. Once scheduled you can see it in the "Jobs Dashboard" and with the "next start time" of what you configured. I have a situation whereby the time it is suppose to start - it doesnt - howevere flags the job as a "success". Not newe device configurations are archived and the "next start time" remain the same. Its almost like it is failing to execute, but some other process under the hood thinks that it was been executed correctly?
Any ideas or experience that could help here would be appreciated!Some extra info that has just come to my attention. At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x. I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2). I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure. But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
HQ-NCS1/admin# show application
NCS Cisco Prime Network Control System
Is that normal? Maybe this is my problem. Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System? When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine. -
WLSE Configuration archive download SNMP timeout
HI, I´m new to WLSE. My AP´s are already discovered and managed, but when I try to download the configuration archive from them, the Job Always fail with a SNMP timeout error message. This problem occur in the upgrade firmware job too.
Whe I go to reports, device center, I can see the AP configuration, but in the configuration>archives>view archive I have nothing.
I appreciate your helpYou can configure the timeout value by selecting Firmware > Advanced Parameters. From this option you can change the "Per device job operation timeout value" to a higher value
-
Cisco Prime Configuration Backup -Failure
My Customer use Cisco Prime Ver 1.4 U2
it Background Task in Configuration backup is show failure all Device
but I can Audit or syn config from WLC is success but config backup not success
i need workaround prove issue ?
ThankAre they reachable? do the controller have proper READ_WRITE community string? can you issue debug transfer tftp enable on controller and see the output
-
Guest wireless WLC configuration doubts
Hi Experts,
I have one WLC which is configured as a Foreign controller and other is configured with Anchor which is connected in DMZ ( behind firewall ) ...
I have one more Anchor controller which is physically connected to other remote office ...
As of now ,All guest clients are connecting to remote site anchor controller which is suppose to connecte locally configured anchor controller.
Can anybody suggest me ... what configuration or settings i need to look into so that guest clients can be connected to locally configured Anchor controller.
Please suggest me ....So you want the remote Anchor controller to be treated as a backup. Right ?
In my knowledge, that's not possible to use only one anchor controller at one time. since we have to enter the Anchor controller details in the foreign controller. So if we enter both the Anchor controllers in the Foreign controller they will start load balancing.
Other process is - make a manual entry in the Foreign controller at the time of primary anchor controller failure so that the traffic start moving to remote anchor controller. This is a work around.
Otherwise I don't know if there are any settings which can be done at the Primary Anchor controller to switch to backup controller in the event of failure.
Maybe you are looking for
-
Error while generating Data provider
We are facing a weird issue while using Design Studio 1.2. Locally the tool works fine but when we use it from BI-Launchpad or through BI Enterprise it gives intermittent error "Error while generating Data Provider" Same setup works fine in our Valid
-
If I buy my ipad online will my $50 gift card come with it?
So I'm planning to buy a ipad but as I read if I buy one of the qualifying products or ipad I can get a $50 apple gift card. Will I get the gift card with my ipad or should I go to my nearest apple store and buy ipad and get the card. Oh and can the
-
Help, can anyone understand "finder.crash.log"?
I've had a problem for a day now... my Macintosh HD couldn't open for a while without crashing the finder (everything on desktop disappearing... then back). Then I made some adjustments, and now the HD will open... but if I switch to view as "list"..
-
Why does Flash add points when I "Undo"?
I converted a bitmap to vector. I am removing all the useless extra points which get created in that process. Occasionally I will mis-click and end up moving or deleting a shape. When that happens I want to use "undo". But ctrl-z and undo from th
-
Can I share files from other programs or just Adobe apps files. I work with Final Cut and Premiere X.? Need to share files up to 6GB. I need to know if the 20 gb limit is about all that I share, or if it's just about whatis in the clouds. If I take,