CPU speed MSI GX620

I have a MSI GX620 as you can see in the title, I installed CPU-Z to read my CPU speed, multiplier etc.
It has a P7350 processor, that should do at least 2 GHz, though when i check it at CPU-z it says i have a speed of 1850 MHz with a multiplier of 6, this all is with the turbo button on.
Before I've had a reading of 2.3 GHz with 7.5 multiplier, that is more like the way i want it, how do i get my CPU to work faster? When I'm playing a game it's at 100% CPU usage but my laptop won't push the multiplier to 7.5 for better results.
Thanks in advance for any replies.

Your CPU is in "standby" mode when you are not doing anything, therefore it underclocks itself. When you play your games, it goes back to its full clock speed. If your CPU is always 100% when gaming it is because the CPU is not able to keep up with the game . Remember, a laptop always has alot less performance than a desktop computer.

Similar Messages

Cpu speed is clocked down during heavy use (msi x79a-gd45) ?

Hi
I overclocked my cpu, intel i7 3930K, 32 gb ram win 7 on msi x79a-gd45
cpu base clock : 100
adjust cpu ratio 42
intel turbo disabled
dram freq @1600
cpu core temp 1.290
hyper thread enabled
Everything else is auto
This pc is running at 4.2 in general but when I do render type heavy cpu rendering cpu speed starts going down to 2900, they oscillate betwen 4200 and 2900/2700. I am trying to get it start around 4000. TO me it is kind of pointless that the cpu would clock down when I need them not too. I do not mind if they are clocked down when they are not in use.
I have 750 W with corsair hydro h60
I asked this issue before but I was not able to resolve. I am hoping that someone else might be able to help me out here .
thanks

Quote from: PirateDog on 07-December-13, 17:08:38
Yes, with a Turbo OC on the Core Ratios (set them all to 44X) in CPU Features sub menu plus the CPU V. and CPU Ratio must both be set to Auto. EIST and C1E enabled. Enhanced Turbo enabled. Overspeed Protection disabled.
If the mainboard also has the VDroop option, then set it to 100%. Have you tried the CPU Ratio OC at 44X with the CPU V. in Auto already? If it is stable, then no need to try the Turbo method of OC. With CPU V. in Auto, you can enable EIST and C1E and get power saving features to work. CPU V. must be in Auto for the voltage to decrease at low use or idle (33C).
Hi PirateDog
Thanks for your reply, very helpful
So I now have
Cpu base 100
ratio 44
EIST enabled (intel turbo disabled, enhanced turbo disabled)
Dram auto
Cpu Core V auto
C1E Enabled
C-State disabled
Cpu Phase Control Disabled
VDroop +%100
This setup seemed to push my average cpu temps by around 7C degrees, so I am around 64C if all are at max. I am not sure if this issue is from another place but worth mentioning. I am not sure if this is still in the good range. On the other hand this setup seems to lower my average idle temps couple degrees.
Before I was using
Cpu base 100
ratio 44 Cpu Core V auto
Dram 1600
and everything else was either disabled or set to auto
Any further recommendations?
thanks

MSI GX620 Cooling Problems

hello everyone!
i bought my MSI GX620 notebook at christmas and till now everything worked really fine. about a week ago i noticed that games,after running about 15-20 minutes, start to run slower, feels like fps would drop around 20. my first thought was the vents got too much dust, so i removed carefully the back of the notebook, so i could clean the vent a bit, but still, i got the same issues. i checked with Everest, the GPU temp is 65°C (149 °F), the CPU temp is 55°C (131°F) while doing just simple browsing. this i think is just fine. but when i start any game ( with low PC requirements too ) the GPU has 91°C and the CPU is 80°C and the framerates just drop after 15-20 mins from about 60-100 to 10-20fps. and that just started some days, maybe a week ago.
can anyone tell me what should i do or try?
thanks , and sorry for my bad english
snuzzie

I've been having the same problem with my GX630. The thing must be really clogged because it gets extremely hot after about five minutes of moderate graphics gaming and slows to a chugging crawl. I'm assuming that the plate on the bottom of your machine is the same as on the GX630, and is pretty large with a little indent for where it's supposed to come off. Did you manage to do this?
I took out all the screws and tried to pry it open but gave up for fear of breaking the whole dang thing.
Anyone have experience doing this?

Newbie: My CPU speed is wrong!

I have a KT3 Ulta-ARU motherboard and an Athlon 1400Mhz CPU with a 266MHz FSB. My diagnostics tools tell me my CPU is running at 1GHz though.
I can't get FuzzyLogic or the other MSI tools to work on my computer any more as they inevitably seem to just stop working and I can't uninstall them either. So how in the BIOS do I fix my CPU speed?
I know this is a dumb question but I just can't figure it out after reading the manual or searching around the site.
Thanks!

No I typically have trouble with the MSI tools. I do a clean install of WinXP Pro, and install the tools from the CD. Then I run LiveUpdate, and invariably one tool conflicts with another, or it tries to update one but can't uninstall it, or both. So I've just given up. My computer is due for an OS reinstall soon anyways.
I just got an MSI GeForce4 TI 4200 video card a week ago too so I would like to have the MSI tools working!

Max cpu speed

My son has a compaq with a msi 6090 v3.0. The online manual says that it will support 2600+ or higher processor. But the MSI website says it will support 2200+ or higher. Doesn't sound like a big deal, but when i clicked on the relevant link entitled 'cpu support' it it had a "no" next to any processor with a higher speed than 2200+. Does anyone have any idea what the max cpu speed is that can be supported by this particular motherboard?
Thanks for any help.

CPU support for 6390 both 2 version is reported by BIOS ver:
BIOS Version:6390 ver1: W6390VMS.150 (ver. 1.50)
6390 ver2: W6390VMS.210 (ver. 2.10)
latest version on BIOS for 6390 ver1 is Version 1.8
latest version on BIOS for 6390 ver2 is Version 2.6(Update Description Support Duron Applebred FSB133 CPU)
if you update with latest BIOS for your mobo you may support higher CPUs
BIOS link here: http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=80&kind=1

Measuring CPU speed in OS X

Is there a way to measure actual CPU speed on OS X? I have tried MSI tools and that doesn't work (at least the version I installed doesn't work, if anyone has a download link that works I would be willing to try it) Any other ideas, I would be very grateful if anyone has a trick that works to view my current CPU speed in GHz. Thanks in advance!

Kappy wrote:
If you can't figure out how to clean the vents then you shouldn't own a computer.
Oh I know how to clean them, it's being allowed to easily clean them without tearing open a warranty/AppleCare covered machine is the problem.
There should be a little door underneath that one can open and clean each of the grills so they don't get clogged up.
What I can't figure out is why these grills are located AFTER the fans and before exiting the machine,
What's the grills there for? To keep out bugs? LOL
Figure the smarter thing to do is make a door or rubber sleeve that blows opens under fan pressure so it blows the dust out, not trap it inside.
When the fan stops, the door/sleeve closes keeping bugs out.
Planned obsolence built in.

What is the max supported CPU for MSI 865PE-NEO2-LS?

Can someone please tell me what is the max supported CPU speed for the MSI 865PE-NEO2-LS? I have a P4 2.8@800Mhz, but was told that with a BIOS upgrade this motherboard can achieve up to 3.2? Is that right, or can it support higher speeds such as the 3.4+
Thank you!

Hello,
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=433&kind=1
I think A6728IMS.210 means BIOS 2.1 so it may already work with the 3.2Ghz CPU.
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=433&kind=1

K8T Neo-FIS2R V1.0, CPU Speed Problem

Hi, I got a Athlon64 3500+ (NewCastle) and K8T Neo-FIS2R V1.0 MotherBoard
Just downgrade my bios from 9.2 to 3.3 since the 9.2 bios does not show the correct +3v voltage in the core center and the website is recommending that old version of Athlon should use 3.xx bios.
But the problem occurs, the core center now shows the cpu speed is 1xx rpm and keep sending alarm. I use other software to check the fan speed and it is 2xxx rpm. The temp of the cpu is between 33 to 43 'C.The temp of the case stays at 42 'C. The voltage of the CPU is 1.52-1.53V. One time, somehow the temp of the cpu went up to 50'C but the fan is not turning faster to cool down the CPU. No matter what models (Cool&Quiet or User) I choose in the core center, it just did not go faster. Finally, I have set full speed of the fan in the core center to increase the speed of the fan.
My PSU is Enermax 450W, and I used 5V for my three case fans since they are really noise.
Any problems with my system or computer, or any recommemdation?
Sorry for my English, but I am doing my best.

Everest just has no readings that work for us. They never supported our board. None of the software gets a correct read on our 3.3v so no there is no answer. I have tried them all as have others. If reading the 3.3v is that important to you use a meter.
I have yet to ever trust Core Center. It lies. Keep in mind just how many MSI products it is used in. So far it has yet to be that accurate in any Via Based MSI product. Search the forum here for it. No one seems overjoyed with CC.

Help me i've got a problem with my cpu speed

I have bought prince of persia 2 and after the installation i want launch it but it indicates me I haven't the minimal configuration for the cpu speed(it's indicated 800mhz)
my config:
k8n neo platinum
amd 64 2800+ (fsb 200mhz and multiplier 9x in the bios 1.4)
1gb ddr 400
ati radeon 9800pro 128mb
i look for and i find : cpu-z indicates 200mhz for the fsb and 4x for the multiplier
the same thing when i launch corecenter
please help me

ok you're right i restore the correct frequency
thank you thank you thank you
but it's nevertheless strange my multiplier moved from 4x to 9x on account of cool and quiet

How to get statistics (or precise data) about cpu speed and RAM

My problem is I want to determine the CPU speed of the computer is running the applet.
I know there's no way to obtain in a simply (and standar) way this property, so I've thinked about generating statistic methods for do it (something like executing a loop a defined iterations)
My doubt is what to put inside this loop, beacuse I would like to know just not CPU speed (or satistics about it), I need also free RAM statistics, so I've thinked there would be some specific java instructions to give a relationship of these data I need.
My question is if someone has done (or has thinked about) this kind of classes before me, and can tell me what is the best way to make the same.
Tanks

http://www.javaworld.com/javaworld/javaqa/2002-11/01-qa-1108-cpu.html
http://java.sun.com/products/jdk/1.2/docs/guide/jvmpi/jvmpi.html#hprof-cpu

T430 CPU speed question

Hi,
I recently bought a T430 advertised as having this cpu:
Intel Core i7-3520M Processor (4M Cache, up to 3.60 GHz)
However in my control panel the i7 cpu shows up as 2.90 GHz. Can anyone please tell me if there is some option to increase the speed in the BIOS or similar? Many thanks.
Michael.

michaelmartin wrote:
Intel Core i7-3520M Processor (4M Cache, up to 3.60 GHz)
However in my control panel the i7 cpu shows up as 2.90 GHz. Can anyone please tell me if there is some option to increase the speed in the BIOS or similar? Many thanks.
Michael.
The CPU can dynamically change speed in order to conserve power. If you have a CPU speed monitor you can see these transitions routinely. Here are some samples showing my T430s (i5-3320M up to 2.60GHz) taken about a minute apart:
Cheers... Dorian Hausman
X1C2, TPT2, T430s, SL500, X61s, T60p, A21p, 770, 760ED... 5160, 5150... S360/30

MSI GX620 Tv-tuner

Hi!
Now I bought MSI GX620-063 notebook.I tried to install the tv-tuner,but I couldn't do it.I found the Tv-tuner antenna interface in the notebook...I read the instructions,this is optional....Does any Tv-tuner belong to the notebook or not?
Thanks for the help in advance ...

You need to ask your reseller, was the TV tuner listed in their specs?

Program taking up all of CPU Speed

Hello,
I have been lucky not to have to use the forum, until now. I recently installed a program called Garage Sale. I decided not to use it and deleted it (drug it over to trash from the finder window). Well,(now at least a week later) I turned on my computer this morning and it was running really really slow. I was finally able to get into the activity monitor and was able to find the problem. A piece of Garage Sale was still running (Garagesalehelper) and it was taking up to 65 - 80% of my CPU Speed. How to do I get rid of this thing? Thanks for any and all help.
Imac G5 Isight 512MB 180GB HD 10.4.9 Mac OS X (10.4.9)

Welcome to Apple Discussions, JoeCat24
To stop the offending process immediately, you can highlight "Garagesalehelper" in the main Activity Monitor window and then click the red "Stop Process" button. However, this fix is only effective until you restart your Mac or the application.
To get permanent relief, you must properly uninstall Garage Sale.. I do not use Garage Sale, so I cannot give you specific, step-by-step instructions. You will need to find the proper uninstall instructions. Some applications come with an uninstaller. Others list all the files that must be removed along with their locations
If you still have the Garage Sale installer or Readme files, check there to see how to properly uninstall. If you do not have this information, you may need to download the installer again to see if uninstall instructions are available there. Sometimes it is simpler to reinstall the application and then use the Help files to find out how to properly uninstall.
If none of those things work, I suggest that you contact the software developer and ask him for instructions on how to uninstall his app.
If this GarageSale is the app causing your problems, the developer offers email support via his "Contact & Support" link.
Jim

Firefox wants newer Flash player but my machine doesn't meet Flash 10.2 CPU speed

Just installed Firefox 3.6 and it says I need to update Flash player plug-in, but my machine doesn't meet the current Flash player 10.2 system requirements, ie for CPU speed. My CPU is 1.7 GHz. New Flash wants something like 2.4 GHz. I have 128 MB of dedicated graphics.
IE does display flash content, using Flash active X plug-in, 10.0.32.18
Otherwise like Firefox.

Update to the latest version of Flash that is compatible with your system. (probably 10.1 r102) After that ignore Mozilla's messages about needing to update Flash.
IE uses a different version of Flash (ActiveX) than other browsers use (Plugin), so it's like comparing apples and oranges.

HOw do I find out Ram, JVM version, CPU speed in Solaris 8?

I need to find the following in Solaris 8:
RAM
Java Virtual Machine version
Sun Version
CPU speed
How many CPU's
Available disk space
What are the commands to find this information out?
Thanks!

RAM --> % /usr/sbin/prtconf | fgrep -i 'memory size'
Java version --> % java -version
Sun version --> % uname -a
CPU speed --> % /usr/sbin/psrinfo -v
How many CPUs --> % /usr/sbin/psrinfo | wc -l
Available disk --> % df -k
You may also want to look at the man pages for each
command I've given.

CPU speed MSI GX620

Similar Messages

Maybe you are looking for