CPU will not boot up

CPU will not boot up. When the power button is pressed, either from a cold boot, power off or from a reset, the hard drive begins to operate, then you hear 4 beaps a pause of about 5 seconds and then the fan races.

You may have to repurchase some programs if you can't recover their registration codes, etc... Try though some of the data recovery techniques outlined on my backup FAQ*:
http://www.macmaps.com/backup.html
Also try replacing the clock battery.
- * Links to my pages may give me compensation.

Similar Messages

Satellite M40x will not boot up after CPU upgrade test

I have an M40x Laptop. I took the CPU out of it to replace it with another to test the computer booted up fine so I shut down and took it out and put it's original CPU back in, and it would not boot. Now it will not boot up at all with either of the CPU's all. When I turn on the power all I get is a white screen for a few seconds and the laptop shuts itself back down. Both the CPU's are good because I have since tested them in other computers to make sure that was not the problem.
Anyone have any ideas on what is causing this??

Im not surprised.
As far as I know Toshiba does not support any CPU upgrades and it's not advisable to do something like that.
Its a fact that the CPU replacement on the notebooks is not easy and mostly not recommended.
The processors used in portables are connected to the system board using a process called TCP (Tape Carrier Package). This is a permanent connection method and is used in the interests of miniaturization and heat dissipation.
Did you assign the new heat paste? Its necessary and important if you want to connect the CPU again.
So possibly this is a reason for the no booting.
I think more details you will get from the service guys in your country

Will not boot up on 1st try

Hey everyone,
I am having a strange problem, My computer will not boot up on the 1st try after it has been shut off for 2 hrs or more. Here are my specs and then I will go into more detail. I like to use pictures because some of the terminology escapes my vocabulary.
MSI P6N Diamond LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard
Intel Core 2 Duo E6850 Conroe 3.0GHz 4M shared L2 Cache LGA 775 65W Dual-Core Processor
ZALMAN CNPS9700 LED 110mm 2 Ball CPU Cooler
2 X Seagate Barracuda 500GB 7200 RPM SATA 3.0Gb/s Hard Drive In Raid 0
XFX GeForce 8800GT 512MB 256-bit GDDR3 PCI Express 2.0 HDCP Ready SLI Supported Video Card
Kingston HyperX 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
BFG Tech 800W Power Supply>>+3.3V@24A,+5V@30A,+12V1@20A,+12V2@20A,+12V3@20A, +12V4@20A,[email protected],[email protected]
2 X LITE-ON 16X DVD±R DVD Burner
SONY Black 1.44MB 3.5" Internal Floppy Drive
COOLER MASTER Stacker 830 Evolution Black Aluminum ATX Full Tower Computer Case
Logitech Z-5300 Speakers 5.1
Samsung SyncMaster 204B monitor
Logitech G5 mouse
Windows XP home, SP2
Build Date 11/26/2007
Problem:
After being shut off for more than 2 hours my computer will not boot up on the 1st try. It goes to a message that says"Reboot and select proper boot device or insert boot media in selected boot device and press a key". I shut it down using the power button, wait for the hard drives to stop spinning, and then hit the power again and it starts up just fine. It will restart just fine also as many time as I want to restart it, after it has been running in windows. Once it is running, it runs terrific, no problems at all.
If you go right into the bios after sitting for a while you see this in the boot sequence, notice there is no hard drives(Nvidia Stripe)in the boot sequence.
After shutting it down and starting right back up this is what you see in the boot sequence. This pic is from a different time, thats why the boot sequence is different.
Here is a short youtube video (2:10 sec) made to help show the problem. (I called it a Cold boot Storage problem for another thread) just ignore that.
Things I have done to try to solve the problem:
1. Update the bios
2.I have moved the boot sequence around, Foppy1st, or CD 1st, ect. and even disabled the [USB:HP Photosm] in the boot sequence, Hard Drives are 1st now.
3.Replaced the Mobo Battery thinking that it was not remembering the boot sequence
4.Checked that the Hard Drives are connected to the correct plugs (6-7) on the motherboard, and that the raid connector JP1 was shorted out for Raid 0 and the blue indicator light was flashing.
* Just a note in this area. I did set up the Raid 0 with a tech from MSI because I was having an issue with the initial set up, and I did use the Nvidia raid drivers that came with the motherboard. Pchas01 in another thread thought that this could be part of the issue because it is not necessary to load the drivers when you set up the Motherboard in the Raid mode.
F10 and look in the Raid Array
5. Pulled the jumper off of JP1 and it just went to the "Reboot and select proper boot device or insert boot media in selected boot device and press a key" screen much faster, but would never boot up after 5 tries. Put the jumper back in and started up on the 2nd try like the normal problem.
6.Went into the On-Chip ATA devices in the bios and Changed the Raid Mode to an IDE, I cannot F10 and get into the Raid Array now, but I guess that is normal.
Now this is what my boot sequence currently looks like.
That is the point that I am right now. It runs great, games are awesome on it. Its just does not want to start up on the 1st attempt.
Thanks for any help on this
Chris aka Fritzpeed novice builder

Thanks for the reply,
I started with the easy fixes first, changed the sata cables, and tried different power supply connectors. Both tests had same results, still boots up on 2nd try. I did not know how soon the problem would re-occur after it has been shut down, my shortest time so far is 25 minutes.
Quote
Why only one RAID channel is enabled? Array can't be detected in that way...
Well right now, it is not even set up that way, in my #6 problem solving, it was suggested that I turn the Raid Mode off and try [IDE] to see if that made a difference,"because I don't need Raid enabled for the hardware raid". It did not, it only booted to the "Reboot and select proper boot device or insert boot media in selected boot device and press a key" window about 60 seconds faster. It is currently set up in this way.
This is how it looks in my On-Chip ATA Devices
How do I check this?
Quote
Does the problem persist when you use Silicon RAID instead Nvidia RAID?
I am still working on getting the seagate diagnostics to work, I am getting an error message before I can even test them.
I do have another question. Why is my HP Printer showing up in the Hard drive test, and also why is it showing up in my boot sequence, is this normal?
And speaking of boot sequences I got in there again just now and saw 2 [USB:HP Photosm]
Thanks again, still working on testing hard drives.
Chris

IMac will not boot from any mode except Target Disk

I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot, and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
I reformatted the HD and installed 10.7 again, it still freezes up at the same point.
I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
UPDATE...
Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own. I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
I did manage to have it start one time got a copy of the the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
Specs...
The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
Error Report…
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

Here is the complete error log...
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80602db800 : 0xffffff801a41d5f6
0xffffff80602db870 : 0xffffff801a4b7b95
0xffffff80602dba40 : 0xffffff801a4ce4ad
0xffffff80602dba60 : 0xffffff7f9bab8654
0xffffff80602dbb60 : 0xffffff7f9baa218c
0xffffff80602dbbb0 : 0xffffff7f9baa20e2
0xffffff80602dbbd0 : 0xffffff7f9ba73554
0xffffff80602dbc00 : 0xffffff7f9aa8d470
0xffffff80602dbc40 : 0xffffff7f9aa8d3df
0xffffff80602dbc60 : 0xffffff7f9aa926ec
0xffffff80602dbcf0 : 0xffffff7f9aa8af20
0xffffff80602dbd20 : 0xffffff7f9aadacc7
0xffffff80602dbd70 : 0xffffff801a833b9b
0xffffff80602dbdc0 : 0xffffff801a862d57
0xffffff80602dbe30 : 0xffffff801a497cef
0xffffff80602dbe80 : 0xffffff801a420abd
0xffffff80602dbeb0 : 0xffffff801a410448
0xffffff80602dbf00 : 0xffffff801a4195fb
0xffffff80602dbf70 : 0xffffff801a4a5ad6
0xffffff80602dbfb0 : 0xffffff801a4ced13
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
         com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
         com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
            dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12B19
Kernel version:
Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
Kernel slide:     0x000000001a200000
Kernel text base: 0xffffff801a400000
System model name: iMac8,1 (Mac-F227BEC8)
System uptime in nanoseconds: 26349024446
last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
loaded kexts:
com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
com.apple.driver.AppleHDA          2.3.0f2
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.filesystems.autofs          3.0
com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.AppleMuxControl          3.2.6
com.apple.driver.AppleBacklight          170.2.3
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.GeForce          8.0.0
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ApplePolicyControl          3.2.6
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleIRController          320.15
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.1
com.apple.driver.AppleFWOHCI          4.9.5
com.apple.driver.AppleUSBHub          5.1.6
com.apple.driver.AirPortBrcm43224          600.36.17
com.apple.iokit.AppleYukon2          3.2.3b1
com.apple.driver.AppleAHCIPort          2.4.0
com.apple.driver.AppleIntelPIIXATA          2.5.1
com.apple.driver.AppleUSBEHCI          5.1.5
com.apple.driver.AppleUSBUHCI          5.1.5
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.driver.DspFuncLib          2.3.0f2
com.apple.iokit.IOAudioFamily          1.8.9fc9
com.apple.kext.OSvKernDSPLib          1.6
com.apple.kext.triggers          1.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.nvidia.nv50hal          8.0.0
com.apple.NVDAResman          8.0.0
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.3.0f2
com.apple.iokit.IOHDAFamily          2.3.0f2
com.apple.iokit.IOSurface          86.0.2
com.apple.iokit.IOBluetoothFamily          4.0.9f8
com.apple.driver.AppleGraphicsControl          3.2.6
com.apple.iokit.IONDRVSupport          2.3.4
com.apple.iokit.IOGraphicsFamily          2.3.4
com.apple.driver.AppleSMC          3.1.3d11
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.iokit.IOUSBHIDDriver          5.0.0
com.apple.driver.AppleUSBMergeNub          5.1.5
com.apple.driver.AppleUSBComposite          5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOATAPIProtocolTransport          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          5.0.0
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOAHCIFamily          2.2.0
com.apple.iokit.IOATAFamily          2.5.1
com.apple.iokit.IOUSBFamily          5.1.6
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.18
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
Parallel ATA Device: MATSHITADVD-R   UJ-875
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
USB Device: Trackball, 0x046d (Logitech Inc.), 0xc404, 0x1d120000 / 4
USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

X79A-GD65 (8D) will not boot with 4930K or 3930K

Short version:
My system will not boot but gets stuck at "09 Power on South Bridge Initialization"
Detailed description:
I just bought this system and am when I tried to start it it got stuck at "09 Power on South Bridge Initialization". I have removed everything that is not necessary (gfx-card, HDDs, etc.) and only have the CPU and one memory stick inserted (in slot 1 as per the manual). I have also unplugged and put back all power cables from the PSU several times. I have also tried using BIOS A and B.
As I read on this forum that a BIOS update was needed for IVY-Bridge CPUs I bought a 3930K today to see if I could get the system up and running but it still gives me the same error code.
My board serial number is 601-7760-010B1312109204, assuming it is manufactured 1312 = December 2013.
I don't know the BIOS revision as I have never managed to get past the 09 status code.
Any ideas on what the problem could be?
Bought this monster PC as I have a delivery for a client in need of some RAM-heavy processing, so am really starting to feel stressed out about this by now.
Thanks in advance!
System details:
- MSI X79A-GD65 (8D) X79 S-2011 ATX
- INTEL CORE I7 4930K 3.4GHZ 12MB S-2011
- INTEL 530 80GB SATA SSD MLC RESELLER KIT
- INTEL 530 480GB SATA SSD MLC BULK (4 of these)
- FRACTAL DESIGN INTEGRA R2 750W
- ASUS GEFORCE GT 210 1GB DDR3 PCI-E VGA/DVI/HDMI SILENT
- KINGSTON 64GB 1600MHZ DDR3 ECC REG CL11 DIMM (4X16GB) W/TS (two kits, 128GB in total, don't really need ECC but that's what I could find needing 16GB sticks)

even compared to just 10 years ago sales staff have became really dumb as there just hiring people who do not care about anything as long as they get there cut of a sale (usually all they know is basic Consumer parts they stock) and nearly non of them unless they specialize in that level of equipment will have 0 idea what they work with on a pro level part (ECC memory tends to be used on servers and Professional workstations so if they do not use that type of gear then they probably have no idea what ECC really is at all)!
also in that time some major things have happened especially with computer parts like the memory controller moved from the Chipset to the CPU same with the SATA controller , onboard GPU (thats now on the CPU and some have it some don't) and alot of other things and I guess that the people you dealed with had no idea the memory support has very little to do with the board (all the board can do is have BIOS Timing sets now and lists of parts it supports) and is now to do with the CPU alot more as it has the important stuff on it (there very close to a SOC (System On Chip) now)!
if you plan on building another computer remember to do some research yourself before you get a CPU as it is nearly the most important thing of all and they have different features tied to them and do not expect sales guys to have a idea unless there also a Technical support staff member too and work on computers that are of the same class your trying to make and have at least used the same level gear (usually if your doing something like that find a friend who is a computer nerd tell him what your trying to do and get him to help you choose all the parts)!
let me know how it goes when you get the Xeon and have it installed?

T61 will not boot with nvidia quadro 140m driver

Hi all,
A couple of weeks ago, after allowing MS update to install some FTDI driver updates, my system will not boot up and hangs shortly after the initial vista loading screen. The screen goes black with some HD activity and eventually reboots. After trying a couple of restore points with no luck, I started to remove the latest driver updates and other software to my system again with no luck.
If I uninstall the nvidia driver and use the Standard VGA driver, it will boot and come up properly. I've done a bunch of web searches and searches on this site and can't find my exact circumstances. Its hard to believe that it could be a hardware issue since it started after a software update, but since it hasn't been a problem for anyone else, I'm just not sure at this point.
I've tried earlier versions of the nvidia driver, removing other drivers and services trying to find a coincidence, but nothing seems to work. I'm kind of at a loss at this point. Does anyone have some suggestions?
Thanks in advance,
Dave

More info on my system:
OS Name    Microsoft® Windows Vista™ Business
Version    6.0.6001 Service Pack 1 Build 6001
System Model    6459CTO
System Type    x64-based PC
Processor    Intel(R) Core(TM)2 Duo CPU     T8300 @ 2.40GHz, 2401 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date    LENOVO 7LETC5WW (2.25 ), 11/14/2008
SMBIOS Version    2.4
Installed Physical Memory (RAM)    4.00 GB
Also, does anyone know if using the Standard VGA Display driver without problems on this system means that the video card hardware is working? In other words, I'm trying to rule out a hardware problem with my nvidia quadro 140m card, so if the system works fine with the standard vga driver, would that mean the hardware on the card is ok?
Thanks,
Dave

I have a Macbook pro 4,1 My Battery would not charge after only 23 cycles. I tried the battery update now my macbook will not boot. it has a kernel panic Unable to find driver for this platform:

Macbook 4,1
Early 2008 15" macbook pro
Running Snow Leopard
the Battery was not working after only 23 cycles
I tried the Battery update and now it will not boot at all
I really do not want to loose my data on the drive
panic message is
Unable to find driver for this platform: "ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Please help

Panic Message
panic(cpu 0 caller 0x000x563ebd) : Unable to find driver for this platform:
"ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Debugger called: <panic>
Backtrace (CPU 0), Format - Frame : Return Address (4 potential args on stack)
(7 lines of hex)
BSD Process name corresponding to current thread: Unkonwn
Kernel version:
Darwin Kernel Version 10.8.0" todays date ; root:xnu-1504.15.3~1/release_I386
I tried to boot from CD can, but i dont want to loose any information.
Tried disk tools
Hardware test
Tried to check if it was memory sticks failing or battery , nothing else plugged in
if i boot holding Apple key and S
I get additional warnings about AppleACPIPlatform and not being able to load Kext

Xserve will not boot up, all lights flash rapidly

Just bought a lightly used Intel Xserve. This unit was in a business that failed, and was set up, but never used. Was powered off and unplugged for approximately 18 months. When we tried to plug it up to check it out & configure it, we noticed the following:
System will not post and won't boot
Hard drives do not appear to spin
CD Drive appears to have no power - will not grab disk
All fans do work, and run on high RPM
All lights on back of server and front of server, as well as next to SDRAM slots, and on back of main board flash / flicker (regular quick flashes, no pattern evident). The only light that does NOT come on at all is the light next to the power button.
Anyone heard of a similar condition? Is this server toast?
Thanks,
Rob Hogan

I'm sorry to say I don't have a solution, but I can commiserate.
I have a G5 and two G4's, and so far within a few days / couple of weeks of getting them home and getting them up and running, they seem to fail.
Usually spectacularily.
The G5 operates very much as yours in that power on, fans rev high, and no post or other activity; I don't get any system light status action however other than flashing. I've replaced CPU's and logic board on this.
The single CPU G4's does much the same, but this I've had up and running and then it went down when I upgraded the memory to max (very careful to make sure it was within Apple spec's), and despite swappinbg the original memory back in,nothing.
My latest, a dual core G4, was bought in working order, and I upgraded this from 10.4 to 10.5. Running nicely as a internet gateway. Went away for weekend so put it into sleep mode. Came back, power button on front panel stopped working, and one of the raid slices on the system drive failed.
Tried to repair this and system now no longer boots, but freezes on loading OS (spinning disc stops in mid spin) and it will not boot from installation disc via firewire or internal DVD drive (swapped in a replacement to ensure it works). The installation disc stops at the apple splash screen, but goes no further.
I can, helpfully, get into Open Firmware mode, so something is working on some level. Sadly, I can't seem to find a copy of the Apple Hardware Test for this machine (see my post on this) to check it out.
I can tell you that I'm getting very adept at working with Xserve hardware, if not very effectively.
My working hypothesis on this is that there is some issue with these units being used 27/7x365 for however long, and then being left 'off' for a prolonged period.
Thinking that whilst they are designed to operate reliably as constantly on and working under load, so facet of being 'off' breaks 'something'.
If really pushed to go out on a limb, I'd theorise that under load the electronics/IC's settle into position, but then when switched off things cool down, contract, and causes weaknesses in electrical connections to occur. When next used, these then start to fail, giving a pattern of initial operability followed by delayed failure with a cascade of increasingly servere symptoms until terminal failure is reached.
But that is wild, uneducated, conjecture.
So, no help, but I comiserate.
XD Andy
btw, is anyone has some useful advice for me on where to find the AHT 2.0.1 for Xserve or even just the part number ... ... ...

Power mac G5 turns on but will not boot up

Hello,
I have the last power mac G5 quad core made before apple switched over to intel. I have not used he computer in about 3 month and it worked fine when I put it into storage but when I tried to turn it on today it will not boot up.
There is constantly a yellow light on near to where the RAM snaps in even when the computer is off. (this is the 3rd light up from the bottom and the only on that is on at this point)
When I press the power button a red light turns on for about one second. Next to this light are the words LED806 Checkstop and it is offset to the right of the other lights a little bit when looking into the side panel of the computer. This light also lights up briefly when I press the power button to turn off the computer.
After pressing the power button another red light turns on just above the yellow light that is always on and the screen is still black. Then the screen eventually turns grey with the apple logo as it normally looks except some of the pixels are off colored a bit in square patterns across the screen. When this happens a green light turns on just below the yellow light. Now there are three lights on all at once.
Next the screen briefly turns light blue and then a little darker shade of blue and the computer will not boot up or go any further than this point.
Can anybody tell me what is going on here and is there any way to fix this?
Is there any way to reset or reboot the computer this the install disk?
Distortion on the startup screen (hard to see in this photo)

Hi Mike,
LED 1—CPU A: red—contact Apple or an Apple Authorized Service Provider
LED 2—Overtemp: red—contact Apple or an Apple Authorized Service Provider
LED 3—Power On: red—the main power is on
LED 4—Trickle: yellow—Power Mac G5 is plugged into the wall correctly
LED 5—Open Firmware good: green—no problem
LED 6—CPU B: red—contact Apple or an Apple Authorized Service Provider
LED 7—Checkstop: red—contact Apple or an Apple Authorized Service Provider
Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
http://eshop.macsales.com/item/Newer%20Technology/CR2032/
How to reset the SMU/PMU on a Power Mac G5 (Late 2004) or Power Mac G5 (Late 2005) ...
http://support.apple.com/kb/HT1436

My MacBook Core 2 Duo will not boot up. In safe mode I see keychain problems and Mach 1102.

My MacBook Core 2 Duo will not boot up. In safe mode I see keychain problems and Mach 1102 and it keeps circling through the same error. Also the screen is so faint (pressing the F1 and F2 keys don't do anything). I got this from a friend and he didn't have any of the original discs. Any suggestions? From what I've read it's a problem with a recent update. I've never had a Mac so I'm trying to learn and fix it.

I just had an issue like this. I was able to boot up with an external firewire drive, although it was a lot of trouble. I think doing an option boot finally worked; holding down the option key, I eventually got to see the firewire drive was bootable, and booted from it.
I put the thing in verbose boot mode (command - v , I think; but please look it up. I have no Mac books at work to check). In verbose mode, you could see that the hard drive could not mount; the OS tried to do fsck, but it failed around 2/3 of the way, and the CPU was halted.
I was occasionally able to boot normally, but never in safe or single user modes; these do a disk test first, which invariably failed.
I could see from the system and console logs when I managed to get the firewire boot going that there were repeated errors trying to access drive s03, the internal SATA drive. The logs on the SATA drive showed huges numbers of errors. At a wild guess, for some reason a lot of sectors went bad all at once. There had been a some erratic behavior before, but I'd put that down to the single processor G5 problems. (these were non video related, just freezes).
Applecare wanted me to carry the huge thing into the local Apple store, but I persuaded them to just send me a replacment hard drive, which they did. The new one works perfectly.
PowerMac G5 1.8 SP (late 2004), 1.42 mhz 14 iBook Mac OS X (10.4.3) both with 1.5 GB Ram

New system will not boot up.

I am in the process of building a new system and it will not boot to the post. The power gets to the cpu fan and case fan for about 5 seconds then shguts off. I have to clear cmos to get the same response. Please help, I have pulled everything from the case and tried to boot with just the cpu and memory. Same result.

Quote
Originally posted by FastEddie
The Antec Bug involves their True Power line of psu's and involves a problem with the +5vsb. It's caused quite a few problems with many different boards, from stability issues, to boot issues, to freezing in cmos setup issues. Here's a couple links:
Antec Problems with Neo 2 Platinum
Antec RMA
Read these through.
Would be nice if you guys had different psu's to try.
I recently had the "reboot loop during startup" problem with an Abit AI7 and the Antec TruePower 480. However, the problem didn't start to occur until several months after it was new. After replacing the PS with a 430 amp Enermax the problem went away.

System will not boot or POST

I have a Pavilion A8 Vision that will not boot or complete POST and does not communicate in any way. Fans are on, sounds from drives seems like beginning of POST. I have removed and replaced RAM with other piece - no change. When RAM is out of motherboard system will report 5 long beeps and repeat the beeps for 4 to 5 times. Need help and/or advice on replacement of components.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your computer is not able to start up properly, and that it is emitting a BIOS beep code. I would be happy to assist you in this matter! According to the information in this resource on BIOS Beep Codes, 5 long beeps indicate that 'fatal errors related to the operation of critical motherboard components - such as teh CPU' have become defective. To correct this issue, I recommend contacting our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
www.hp.com/contacthp/
I hope this helps!
Regards

System will not boot up

MB: KT6 Delta-LSR
CPU: XP2500 Barton
GFX: Asus V9520 Magic/T 128mb
RAM: 1028 pc3200 ddr400 (2x512) Geil Branded
HDD: Maxtor 40GB 2mb Buffer
Put it all together formatted the HDD, installed windows, network was working perfectly. (on ASUS via600 board)
Next day turn it on and nothing, zilch not even a flashing cursor top left of screen, dont even boot to DOS. screen is completely blank.
Tested CPU, GFX, RAM and PSU in another base unit and they work fine, yet put them all together and nothing.
1st I thought it was the mainboard so I sent the ASUS board back and ordered the KT6 Delta nice looking board. But still exactly the same problem.
Lights on case are lit all fans are turning ect yet still the system will not boot up i dont even get a flashing cursor top right of my screen.
There is no light with this mainboard for some reason.
All components work when fitted to another mainboard in a different case.
NB: one thing I have noticed is that there are two power sockets on this board,
1. The usual 20 pin socket (which I am connected to)
2. A 4 pin socket near to the CPU (whilst my PSU has a plug that will fit this sockect also, I am unsure as to connect instead of/as well as or leave unplugged.

Like I have stated before, it is the compatibility issue related towards your chip fsb and your memory fsb. I know that not everyone has money to go buy another stick of memory, I don't. But maybe you could exchange from the place you bought and say that it was a mistake? The cheapest route without getting the fsb chip to match the fsb of the memory stick is to get PC2700 memory. Have you tried going for this yet? I'm sure that your motherboard may not be shot, my board didn't get shot after trying to the two different fsb. You have to understand, motherboards are picky when it comes to running the hardware. If there is a conflict, it won't run right, I could run at a lower fsb and get it to work fine, but it wasn't at it's full potential, and I wasn't going to waste my time trying to find the fsb that would work correctly. So, I just let my friend have the stick back. This is why I'm asking you to try a lower speed stick of memory, because I have experienced this. But so far you haven't even seemed to notice my replies, could you take a quick overview of what I have said? Sorry if I come off as rude, just I am taking the time to write these replies and really am trying to help from my knowledge base. I have experienced this type of problem of what you are talking about personally.
Ok, so maybe I might not know it all, seeing that other people replying here have the same mb spec and chip fsb and memory like your trying to run, they might know more when it comes to that area for sure, just I didn't have luck trying to run a faster stick of memory compared to my chip, even though my board could run it, I couldn't get it to work, at all. I would just get a black screen, I thought I shot my GPU. Then I reset CMOS and the bios would flash, then when it would start pulling from harddrive, boom, black screen again. I had my friend tinker with my volt. to the right volts of the memory stick, still couldn't get nothing. This is why I am a little skeptical about you being able to run it at all in the long run. Hopefully you can find a way, maybe it is your manufacturer of your stick, but my conclusion is, if it isn't going to work with one, or two of same speed, try lowering it. Like I said, I tried it on this setup right now, and I didn't have to replace the chip or mobo, or gpu, so those should be fine.

Installed todays security update, computer will not boot, down

I installed todays security update. now my G3 600mhz 14" iBook, running 10.3.9, will not boot.
I have had several symptoms throughout the day. A couple of times it sat there for about an hour with a blank screen. It came up several times with the message to type "mac-boot" ( I may be remembering the syntax wrong) I tried that, I also tried typing "shut-down" at that point.
Later it came up to my background screen bout would do nothing and go no further. Now it is siting there with a OS 9 folder icon in the middle of the screen and sometimes the icon alternates between a face and a question mark in the middle of the icon.

Robert,
I sympathize with your plight. I had a similar problem with my G4 AGP (Sawtooth). Like a dummy, I installed Security Update 2006-004. Upon reading posts about Apple updates on this board, it seem that the knlowledgeable ones wait until the unsuspecting ones walk on the landmines that Apple builds into the upgrades before trying it themselves.
I had exactly the same problems that you describe. Since I believe that my G4 has an extended warrantee, I called Apple Phone Support. The gentleman after listining to my plight, told me that he could not help me because my Mac was a "VINTAGE" model, no longer supported by Apple. How is that for an answer. I guess that now that Apple switched to Intel, all Motorola chips become "persona non-grata".
Anyway, I remember that something like this happened to me some years back with another "upgrade". I believe that basically, the problem is due to the fact that Apple does not make provisions for third party products installed in a Mac. Last time, it was the video card (ATI) that had to be removed in order for the upgrade to work. This time, I had to remove my 2 GHz. Giga Design CPU and put back the measly 400 MHz. Apple CPU. Then I was able to boot normally. I then re-installed the Giga drivers and everything went back to normal. Since I am getting old, and it is recommended for persons of my age to engage in mental exercises, I believe Apple is trying to help me by having my brain work overtime (not to mention the 5 terror-filled hours I spent to resolve the problem.
I suspect the update writes to or resets your PRAM or other non-volatile memory. Does your G3 iBook have any non-Apple components? If so, I suggest you remove it or them. Beyond that, I cannot help you, except to suggest that you reset the PRAM.
I now have transferred most of my data to a fast, trouble-free (relatively) PC. Since in the future, all Macs with have Intel chips, there will be no reason for me, after about 30+ "vintage" years to buy Apple. Of course, just as Apple touts that its OS can run on a PC, PC owners will (are already) running Mac OS on their PC.
Nick

Help! Computer turns on but then will not boot up - Please Help!

I have no idea what happened to my Apple. Someone please help me. My powerbook currently is running on no battery (recall victim) and now the entire computer is no longer functioning at all. I installed iTunes 7.0 and then the trouble began. I had to restart the computer, so I did that and then the computer just wont boot up. It goes to the grey screen which shows the Apple symbol and occurs right before my log in then just continues to read. The green light for the battery is function and nothing at all is working. The computer simply will not boot up, I have tried unplugging it for the night and then rebooting it and nothing. Please someone help, what has went wrong?

You mentioned in your other thread that you had trouble with a cpu(0) hardware error trying to use the hardware test disk. Is this the hardware test disk which came with that particular machine? If not, then you need to find the original hardware test disk that came with that machine. If the restore disks that say 12" Powerbook include the words hardware test, use those instead and follow these directions:
http://docs.info.apple.com/article.html?artnum=86287
If you are using the correct hardware test disk and you get a cpu(0) error using it, then the machine has a hardware problem.

CPU will not boot up

Similar Messages

Maybe you are looking for