Cpuinfo showing only one processor

Hey guys, I just got a new motherboard( cheapass Biostar P4M80-M4) and I'm having problems getting SMP working/figuring out if its working. Doing a `cat /proc/cpuinfo` shows that I only have a processor 0. I am absolutely sure that this processor supports hyperthreading. Hyperthreading is enabled in BIOS and POST confirms this by saying that an HT processor is detected and HT is enabled. The noapic kernel flag is not being set. Booting into DSL shows that I have 2 processes. Any thoughts or ideas? Thanks.

oh yeah i forgot to mention that I'm running stock kernel 2.6.21.
$ dmesg | grep -i processor
Intel MultiProcessor Specification v1.4
Processor #0 15:3 APIC version 17
Processors: 1
Detected 3089.608 MHz processor.
Checking if this processor honours the WP bit even in supervisor mode... Ok.
CPU: Physical Processor ID: 0
Total of 1 processors activated (6186.46 BogoMIPS).
so it is only bringing up one processor?
Last edited by _adam_ (2007-06-13 18:20:59)

Similar Messages

/proc/cpuinfo shows only 1 core on dual-core CPU [SOLVED]

I've recently gone from Arch i686 to Arch x86_64, and now /proc/cpuinfo shows only one core even though it's a dual-core CPU.
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 23
model name : Intel(R) Core(TM)2 Duo CPU P8400 @ 2.26GHz
stepping : 6
cpu MHz : 2266.542
cache size : 3072 KB
physical id : 0
siblings : 1
core id : 0
cpu cores : 1
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc up arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm tpr_shadow vnmi flexpriority
bogomips : 4534.96
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
Have anyone experienced similar problems on x86_64?
Could it possibly be a kernel related error?
/AcId
Last edited by AcId (2010-09-08 21:33:27)

dmesg shows some iterensting info about "Unsupported number of siblings" ?
dmesg | grep CPU:
SMP: Allowing 1 CPUs, 0 hotplug CPUs
setup_percpu: NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 29 pages/cpu @ffff880001800000 s88832 r8192 d21760 u2097152
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
CPU: Unsupported number of siblings 2
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
weird, boot CPU (#0) not listed by the BIOS.
Brought up 1 CPUs

When I open up iphoto and click on the events tab then double click on an event, it used to show minis of all the photos in that event. Now it shows only one photo at a time. How do I get it back? Can you help?

When I open up iphoto and click on the events tab then double click on an event, it used to show minis of all the photos in that event. Now it shows only one photo at a time. How do I get it back? Can you help?

On the bottom bar of the window (on the left iPhoto 11, on the right in other versions) note the slider. Drag it left.
Regards
TD

How to show only one element in drop list(common VO)

Hi All,
I'm using 11g adf jdev.
I have a common view object VO. In this VO one attribute is dropdown list , which i commonly used in some jsf pages .
Now in one particular jsf page i want show only one element in the dropdown list .
how can i handle with out distrib'g the common VO.
THANKS IN ADVANCE

BTW, why you want to display only one item in the list.
If you are sure that the list will be having only one item, why don't you have it as inputText/outputText
How do you filter out the item to be displayed in the list? If that filtering is done on listdatasource bound to the list, the list will automatically show only one item(i.e, the filtered item)
HTH
Sireesha

I added a custom ringtone . Then later I tried to add another three set but now after sync . Am not able to get rid of the first one... It's still there as my custom ringtone. But my iPhone in iTunes shows all four... But the phone shows only one...?

I added a custom ringtone . Then later I tried to add another three set but now after sync . Am not able to get rid of the first one... It's still there as my custom ringtone. But my iPhone in iTunes shows all four... But the phone shows only one...?

Paul--you are a life-saver!! Worked great. I did have to look around to make sure I was getting 4.9 instead of 4.7 (even when the file was named 4.9 at techspot.com), but I finally got the right file, did the install as you suggested, and everything is now fine. One note, though, that I haven't seen mentioned in any of this thread: when I first tried to open up iTunes after getting back to 4.9, the following message appeared: "The file iTunes Library.itl cannot be read because it was created by a newer version of iTunes." I merely went to the old .itl file that was created when I did the update to iTunes 5, renamed it, moved it over to my now new 4.9, and iTunes opened fine. My library was a few days out of date, because of the few days' lag from the time I did the iTunes update, but that was easily taken care of, and everything's now working fine. Thanks again!!!

How do you show only one caller's video display wi...

How do you show only one caller's video output with four people sharing a video call? i.e. the call originator wants to show a DVD video on a TV screen and the other callers want to view the video on full screen not just one fourth of their screen.

Thought I'd try this just in case they are stripping out attachments.
Gary Grow
6457 Audubon Sq Dr N
Mobile, AL 36695
Email: [email protected]
Cell: (251) 422-8817
The American Creed by William Tyler Paige
I believe in the United States of America as a government of the people, by the people, for the people; whose just powers are derived from the consent of the governed, a democracy in a republic, a sovereign Nation of many sovereign States; a perfect union, one and inseparable; established upon those principles of freedom, equality, justice and humanity for which American patriots sacrificed their lives and fortunes. I therefore believe it is my duty to my country to love it, to support its Constitution, to obey its laws, to respect its flag, and to defend it against all enemies.

Customize the legend of a pie graph to show only one series

Is there a way to show only one series in the legend though the pie graph displays more than one series?
Any help is greatly appreciated
Thanks
KK

Here is an example that changes the scale of a graph. I think it is what you are looking for. Post back if it is not.
Bob Young - Test Engineer - Lapsed Certified LabVIEW Developer
DISTek Integration, Inc. - NI Alliance Member
mailto:[email protected]
Attachments:
Update_graph_scale.vi ‏40 KB

All my saved layers disappeared. Shows only one locked black layer.with red sripes

All my saved layers disappeared. Shows only one locked black layer.with red sripes

Apple changed the save behaviour several times in the past few versions of MacOsX - there is a good article about this:
http://www.macobserver.com/tmo/article/os-x-mountain-lion-how-apple-rescued-save-as
The trouble is, you should (I know, not much of a help to you at this point) always create backups AND work with versions. So save many versions (x1, x1a, x2, x2a, etc), because when you work within one master file you run the risk of these type of accidents and there is always a tiny change your file becomes corrupt for some external reason. You never know. Disk space is cheap, losing your work is often a real hassle, and can become very problematic when dealing with clients.
So, save many versions, and make backups of your work. And never NEVER open your original files in any other software - always use a duplicate. You never know what that software might do to your files.
Anyway, have you tried searching for the file name on your mac? Maybe, just maybe there is a duplicate lying around somewhere with the layers intact.

Can inherited events be used with only one processor?

Hi friends!
The question is quite simple: I have one parent event and several events which inherit from the first one. Every inherited event has its own properties and also the inherited properties (which have public visibility in the parent class so that the inheritance is automatic). I pass events to the CEP processor but it only works with the parent class and doesn't with the child ones. I mean, I'm using only one processor and only one CQL sentence.
Is it neccesary to configure one processor for every inherited event?
Thanks!

Hi friend!
Here you are:
<?xml version="1.0" encoding="UTF-8"?>
<beans xmlns="http://www.springframework.org/schema/beans"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:osgi="http://www.springframework.org/schema/osgi"
xmlns:wlevs="http://www.bea.com/ns/wlevs/spring"
xmlns:jdbc="http://www.oracle.com/ns/ocep/jdbc"
xmlns:spatial="http://www.oracle.com/ns/ocep/spatial"
xmlns:application="http://www.bea.com/ns/wlevs/config/application"
xsi:schemaLocation="
http://www.springframework.org/schema/beans
http://www.springframework.org/schema/beans/spring-beans.xsd
http://www.springframework.org/schema/osgi
http://www.springframework.org/schema/osgi/spring-osgi.xsd
http://www.bea.com/ns/wlevs/spring
http://www.bea.com/ns/wlevs/spring/spring-wlevs-v11_1_1_3.xsd
http://www.oracle.com/ns/ocep/jdbc
http://www.oracle.com/ns/ocep/jdbc/ocep-jdbc.xsd
http://www.oracle.com/ns/ocep/spatial
http://www.oracle.com/ns/ocep/spatial/ocep-spatial.xsd
http://www.bea.com/ns/wlevs/config/application
http://www.bea.com/ns/wlevs/config/application/wlevs_application_config.xsd">
     <bean id="myConverter" class="com.bea.wlevs.adapter.example.mesevents.MeSEventsAdapter"/>
     <wlevs:adapter id="jmsInbound" provider="jms-inbound">
          <wlevs:listener ref="mesEventsChannel" />
          <wlevs:listener ref="inputPetitionChannel" />
          <wlevs:instance-property name="converterBean"
               ref="myConverter" />
     </wlevs:adapter>
<wlevs:event-type-repository>
<wlevs:event-type type-name="MeSEvent">
<wlevs:class>com.bea.wlevs.event.example.mesevents.MeSEvent</wlevs:class>
</wlevs:event-type>
<wlevs:event-type type-name="InputPetition">
<wlevs:class>com.bea.wlevs.event.example.mesevents.InputPetition</wlevs:class>
</wlevs:event-type>
</wlevs:event-type-repository>
<wlevs:channel id="mesEventsChannel" event-type="MeSEvent" advertise="true">
<wlevs:listener ref="mesEventsProcessor"/>
</wlevs:channel>
<wlevs:channel id="inputPetitionChannel" event-type="InputPetition" advertise="true">
<wlevs:listener ref="mesEventsProcessor"/>
</wlevs:channel>

<wlevs:processor id="mesEventsProcessor" />
<wlevs:channel id="mesEventsOutputChannel" event-type="MeSEvent" advertise="true">
<wlevs:listener>
<bean class="com.bea.wlevs.example.mesevents.MeSEventsBean"/>
</wlevs:listener>
<wlevs:source ref="mesEventsProcessor"/>
</wlevs:channel>
<wlevs:channel id="inputPetitionOutputChannel" event-type="InputPetition" advertise="true">
<wlevs:listener>
<bean class="com.bea.wlevs.example.mesevents.MeSEventsBean"/>
</wlevs:listener>
<wlevs:source ref="mesEventsProcessor"/>
</wlevs:channel>
</beans>
It says the following:
As you can see there are two input channels which are both connected to the JMS adapter as well as only one processor which is connected to the input channels and to the output channels. It is supposed that each event goes through each input and output channel but it fails and says the following:
Channels mesEventsOutputChannel and inputPetitionOutputChannel from the same query must have the same event type.
InputPetition is MeSEvent's child. It inherits all MeSEvent's preperties.
Does anybody know what is happening?
Thanks!

Why can't i send multiple files through airdrop ? , it accepts but shows only one photo

why can't i send multiple files through airdrop ? , it accepts but shows only one photo

Hello there Laurengrayce,
I message all of the time and I want you to do the same, to anyone you would like! Demmo provided a good suggestion of having this person check their services and ensuring they're setup as a 10-digit number, but I would like to provide some of my own suggestions.
If they are in fact already setup as a 10-digit number, I would recommend deleting this persons contact from your phone as well as the entire messaging thread (long press and hold on thread to delete). Readd them to your contact list and try again.
Please advise if this continues and they've already checked with their provider.
Thanks,
MelissaM_VZW
Follow us on Twitter @vzwsupport

My iPhone show only one image Conect USB to iTunes (on PC).What i doing??

My iPhone show only one image: Conect USB to iTunes (on PC), and I do not restart my iPhone.What i doing?

Hello 2000Skyfall,
It seems your device may be stuck in recovery mode. At this point your device may need to be restored. Have you created a backup at any point via iCloud or iTunes? The following article provides details on recovery mode:
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
Get more help
Learn what to do if you don't see your device in iTunes for OS X, or in iTunes for Windows.
If you put your device into recovery mode by mistake, restart it. Or you can wait 15 minutes and your device will exit recovery mode by itself.
Thank you for contributing to Apple Support Communities.
Cheers,
Bobby_D

My Power Mac Dual 1.8 shows only one CPU under the hardware tab is this OK?

I thought it should say two CPUs.
Thanks

I'd love to help you but you should elaborate a little bit. If you're talking about the icon, it will only show the one icon for both processors. If you're talking about the processor palette, that's a different issue.
Did you happen to install the Apple CHUD (Computer Hardware Understanding Development) Tools? The CHUD tools feature the ability to turn off individual CPUs while the system's running, and if that's the case, the System Information would be changed to match the current CPU count.
If you've never used Apple's CHUD Tools, then either the information is flawed or one of the CPUs failed.
Message was edited by: timeconsumer

Preview shows only one page of article

I have a 23-page portrait-only article for which I can preview only one page. Normally it is the first page, but if I click on any other page, the preview shows that page -- but the slider on the bottom of Content Viewer shows only the first page regardless of what page is in the preview window. I'm a newbie at this, and this is my second article; the first one worked just fine. Put them together in a folio, in either order, and the "normal" one shows all pages, and the other shows only page 1. Any thoughts?
Jose

Silly newbies... I read some of the layout options in Plain English. Apparently, if the article isn't set to "horizontal swipe only" it's on vertical swipe only, not "optional." The Aha! moment came from accidentally brushing the mouse so that the preview scrolled upward, revealing the pages hidden below. Now I get it.

How do I show only ONE iCal calendar at a time?

I'm using iCal to manage several different calendars on different websites and also have different calendars of my own. Currently they all show in iCal and this is getting very difficult to manage. How do I adjust iCal to show only the events associated with one calendar, e.g. the calendar I have clicked on, rather than all of them? Do they all have to show?

Thanks - that's better than nothing, but switching them off/ on is still a bit fiddly as I will want to update different calendars frequently.
I was hoping that it would be possible to set it up to simply show the calendar you had clicked on on at the moment, and also to set a default set of calendars to be on as a group (i.e. those I use to organise my own time).
With one click I could then go from my personal calendars to one used for an external website and back again.

Show only one mail acct messages at a time?

Is there a way to show only messages from one email acct and not the combined messages from the linked accts in the new Mavericks update using Mail App? I would like to be able to see only messages from one acct and not them all combined together.

Thank you! I feel like an idiot bc I didn't even see the triangle. The new look just threw me off. Thank you!

Cpuinfo showing only one processor

Similar Messages

Maybe you are looking for