CR52-A2 CD-RW (track following error???)

I have a 52x24x52x, burn some discs and now y get TRACK FOLLOWING ERROR every time i tried to burn, what is it????
I use nero and, i see the possible problems, but nothings happen.
Somebody knows the problem.

Are you using the latest firmware 180D? If not, try that first.
Otherwise it's probably the 180D firmware that's the problem. When I flashed to it, the drive refused to read my CD-RWs any more (Verbatim 16-24x / Fujufilm 4x), even though 180D's meant to increase CD-RW compatibility. Had to flash back down to 161D to fix the problem.
Can get firmware here
h**p://forum.rpc1.org/dl_firmware.php?category=6&manufactor=21

Similar Messages

I keep getting the following error message when I try to update my itunes, "There is a problem with this windows installer package. Aprogram run as part of the set up did not finish as expected. Contact your support personnel or package vendor."

I keep getting the following error message when I try to update my itunes, "There is a problem with this windows installer package. Aprogram run as part of the set up did not finish as expected. Contact your support personnel or package vendor."

Yes, I had found a similar solution also. I'm running XP Pro, SP3. I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair. Then run the 10.5 exe.
While the programme updated from version 8 of iTunes, my new iTunes is now a mess. Not all of my music was in the same folder previously but it all showed up on iTunes. Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing. I haven't begun to work on that.

Track Initalization Errors

Hello. I know there have been topics posted about this, however, none seem to answer my problem. I am using iDVD 6 with the Reflection Black theme. Unlike the other threads I have seen, the movie I am exporting into iDVD is a Quicktime movie from a Final Cut Pro project. I followed the instructions from Apple and successfully imported all my chapter markers automatically. Previewing the project works great too. However, when it comes time to burn, after waiting about 15-20 minutes for the computer to finish rendering my menus, once iDVD gets to the "Burn" step, I immediately get a message that says I have a Track Initialization error. It then said to try reencoding my assets. I did that, tried again, and I get the same message. I am using a MacBook Pro and have over 20 GB of free space. The size of my 10 minute Quicktime movie is 4.7 GB, but I assume that the file size goes down after being converted into MPEG 2. I have also tried to burn with other themes, even ones from the original iDVD, and that doesn't help. The only time I had a successful burn on my new computer was when I filmed a short 10 second movie in iMovie from my iSight. I don't think that is the problem though because on my G4 Desktop with iDVD 3 Quicktime movies from FC Pro burn fine. I have also tried burning to a disk image. Maybe Apple pulled iDVD support for FC Pro 3 in the newer iDVDs? Thanks for the help.
MacBook Pro 15" Mac OS X (10.4.6) 1 GB RAM, Bootcamp, iLife 06

all my chapter markers automatically.
Did you put a chapter marker at the very beginning?
These are "The Rules" for chapter markers in iMovie:
Make sure no chapter markers are within two seconds of the start or end of the timeline. Make sure no chapter markers are within a transition. Make sure no chapter markers are within two seconds of the end of a transition.
I have also tried burning to a disk image.
You get the same message creating a disk image?

Processing data for a remote command failed with the following error message: Error occurred during the Kerberos reponse.

Hi!
We have 5 Exchange 2013 servers and when I’m trying to run a script that includes the cmd-let Get-MessageTrackinglog with StartDate = the first of the month and with EndDate = the end of the month I get the following error message after
a couple of hours. The script is run on the server SERVER01 and goes through the Message Tracking logs of all Exchange servers. I have tried the script on other servers and get the same result.
Processing data for a remote command failed with the following error message: Error occurred during the Kerberos reponse.
[Server=SERVER01, TimeStamp = 918/2014 19:32:34]
For more information, see the about_Remote_Troubleshooting Help topic.
    + CategoryInfo
: OperationStopped: (server01.domain.com:String) [], PSRemotingTransportException
    + FullyQualifiedErrorId : JobFailure
    + PSComputerName
: server01.domain.com
I have gone through “about_Remote_Troubleshooting Help topic”, but can’t find anything related to my issue. There is nothing in the Application or the Windows PowerShell log either.
/Henrik

Hi Henado
Check the time on your Exchange server(s) relative to the DCs and ensure they are in correct sync
Use another account which is assigned the Organization Management permission and log to to the server run the command in shell and see the results
Run
Add-PSSnapin -Name Microsoft.Exchange.Management.PowerShell.E2010
Set-Adserversettings -ViewEntireForest $True and then run message tracking command and see the results
If none of the above helps you may need to remove and re-install the WinRM and see the results
Good Luck :)
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you Check out my latest blog posts on http://exchangequery.com

User Tracking - Application error: URN_NOT_FOUND

hello
running ciscoworks 3.2 on Windows 2008 SP2 - installed apps are:
1. Campus Manager 5.2.1
2. CiscoView 6.1.9
3. CiscoWorks Assistant 1.2.0
4. CiscoWorks Common Services 3.3.0
5. Device Fault Manager 3.2.0
6. Integration Utility 1.9.0
7. Internetwork Performance Monitor 4.2.0
8. LMS Portal 1.2.0
9. Resource Manager Essentials 4.3.1
When I run a quick report in Campus Manager (User Tracking > Reports) I get the following error appearing in a window:
Application error: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!.
Acquisition is working fine – on completion it states how many new hosts have been discovered but I get the above error when I try running a report.
Reloaded server but problem persists. I’ve attached the output of pdshow and the cmapps log - any advice/guidance appreciated.
Thanks
Andy

Hello,
I have the same problem.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Tabla normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
LMS2.6
could anybody help me?
I attach the ctm_config.txt file.
Thanks

LMS 2.6 User Tracking - Application error: URN_NOT_FOUND

Hi,
When I run a quick report in Campus Manager (User Tracking > Reports) I get the following error appearing in a window:
Application error: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!.
Could anybody help me?
I attach the ctm_config.txt file
thanks

From which directory did you get this ctm_config.txt? I need to see the ones under NMSROOT/MDC/tomcat/webapps/campus/WEB-INF/lib and NMSROOT/MDC/tomcat/webapps/cmapps/WEB-INF/lib.
Since this is LMS 2.6, I also need to see the output of the pdshow command.

When I try to unzip the files I get the following error msg "checksum error in adbeapecore.dll"

when I try to unzip the files I get the following error msg "checksum error in adbeapecore.dll"

Hi,
We are tracking this issue at:
http://forums.adobe.com/message/4286522#4286522
Please follow the steps and update thread if your issue is resolved.
Regards,
Ashutosh

Proportional valve and following error problem

Hello, I have a problem with using a NI-7344 card and controlling a proportional valve and hydraulic cylinder.
Everything is working fine in regards to motion and velocity control.
The problem I have is with the following error and halt command. When the cylinder is moving I mechanical disconnect my linear encoder ( 20 pulses/mm) expecting for the following error flag to immediately stop the motion once the value of the following error has been reached. The total stroke is 1016 mm.
What I observe is that the hydraulic cylinder will continue to move for about 20mm when my following error has been set to 50 counts (which should mean 20pulses x 4 / 50 = 1.6mm). I am moving at a rate of 10mm/s
I have also observed that the faster the velocity the smaller the error I see with respect to the cylinder stopping when the encoder is discounted. I am moving at 60mm/s when that happens.
The reason I am discounting the encoder is to try to simulate a partial stuck mechanical system.
Another note is that when ever a "Stop" or "Halt" command is issued in MAX or in our own code the cylinder will stop immediately, so it has nothing to do with the "Kill" command that is issued when a following error has occurred.
Any thoughts on this one?

I think we need to keep in mind that this is a valve that when power is shut off from it, it closes immediately and no motion occurs, not like a motor that could run on a little.
We have issued Kill, Stop, and Halt commands with the same result; the cylinder stops dead in its tracks, no inertia, no nothing. It is only when the encoder stops counting ( because we have mechanical disconnected it from the cylinder, not electrically) will it continue moving for 10- 20 mm after the error flag has been raised.
I'm starting to question the PID loop response. When a PID controller sense's that it's feedback is not keeping up with the demand, isn't it normal for it to increase the output to try to correct the problem. Then my following error kicks in and shuts down the axis? Resulting in a greater error than what was set in the following error parameter. Why this error in motion decreases with a increase velocity, I haven't figured out yet.
Anyway, keep the suggestion coming, someone has an answer to this.
Thanks.

This page contains the following errors:

More and more often I'm getting this message in Safari. I don't recall every getting this message at all until recently and every day it seems to have more and more. What's the issue and is there anything I can do about it?
This page contains the following errors:
error on line 1 at column 1: Extra content at the end of the document

Hi,
www.logitech.com/revolution works fine on my version of Safari (2.0.4 v419.3) so it's not specifically a Safari bug as such.
One quick test you can do to help narrow down things is to try Safari in another user account.This will help us to know whether your problem is local to your account or system wide. If you don't have another account you can use System Preferences -> Accounts -> [+] to create a test one (and [-] to remove it if needed)
For your your internet connections are you using any proxies? (You can check in the System Preferences -> Network pane)
Also, what Safari add-ons have you both added in the past? Maybe we can track it down to a common add-on between you both.

Block change tracking file error

Hi,
when i selected
"enable block change tracking for faster incremental backups" option under Backup setting policy, and apply it, i get following error
error: "since the database area is not set you must specify a block change tracking file"
how can i fix this error.
1. is it better to provide a block change tracking file, if then how do i do it.
else
2.how can i set a database area
Thanks,
Philip.

Hi Anita,
i have 2 more problems which i have explained below.
1. i am running my oracle 10g in linux and after starting the listener, when i try to start the database using
"dbstart" command, i get following error
"Failed to auto-start Oracle Net Listener using /ade/vikrkuma_new/oracle/bin/tnslsnr"
i really have no idea what is this error and how to solve this erorr. Can you please help me. i have also posted a separate forum for this with the heading as
"dbstart" command error
2. my tnsservice name works sometimes and some other times it does not work at all.
at sqlplus prompt when i login as
sys/pwd@orcl as sysdba
sometimes it works fine, other times it gives me error similar to -- protocol could not identify this service name.
Thanks,
Philip.

No tracking and error displayed when launching AICC content in IE11

I am publishing a course to AICC format using Captivate 5.5. When I launch the course in SCORM Cloud using IE11, the following error is displayed:"ERROR - LMS did not return a valid status code." The course loads in the background, but tracking doesn't work.
Note - I've also downloaded a trial version of Captivate 8, created a short demo file and I get the same error on SCORM Cloud using IE11. This appears to be an IE11 only issue - works fine in Chrome and Firefox.
Thanks in advance for your help.

Gary White wrote:
> True. However, a doSomething() or die("Some message");
will display Some
> message if the function fails, regardless of
display_errors.
No, it won't - at least not in this case.
I didn't notice it first time, but there's no closing
parenthesis after
the database name, which causes a parse error. Even when you
correct
that, the problem that Mick spotted causes another parse
error. Both
parse errors prevent anything appearing onscreen if
display_errors is off.
There are at least three mistakes in that script. The one I
spotted, the
one that Mick spotted, and the closing parenthesis that I've
just
noticed. The following might work:
<?php
DEFINE ('DB_USER', 'manda');
DEFINE ('DB_PASSWORD', '*****');
DEFINE ('DB_HOST', '**.***.**.***');
DEFINE ('DB_NAME', 'products');
$dbc = @mysql_connect (DB_HOST, DB_USER, DB_PASSWORD) OR die
('Could not
connect to MySQL: ' . mysql_error() );
@mysql_select_db (DB_NAME) OR die ('Could not select the
database; ' .
mysql_error() );
$search=$_POST["search"];
//get the mysql and store them in $result
//change whatevertable to the mysql table you're using
//change whatevercolumn to the column in the table you want
to search
$result = mysql_query("SELECT * FROM products WHERE item
number LIKE
'%$search%'");
//grab all the content
while($r=mysql_fetch_array($result))
//the format is $variable = $r["nameofmysqlcolumn"];
//modify these to match your mysql table columns
$image=$r["title"];
$item_number=$r["message"];
$title=$r["who"];
$description=$r["date"];
$price=$r["time"];
//display the row
echo "$image <br> $item number <br> $title
<br> $description |
$price <br>";
?>
David Powers, Adobe Community Expert
Author, "Foundation PHP for Dreamweaver 8" (friends of ED)
Author, "PHP Solutions" (friends of ED)
http://foundationphp.com/

IDoc Tracking: RSEIDOC2_CALL_VIA_RFC_DOCNUM error

Hello!
With SP19 there is a new IDoc Tracking functionality available. You can click on an IDoc number in IDX5 and it takes you the IDoc monitoring in the sending or receiving system. However, for some SAP systems I get the following error:
Error during remote call of method RSEIDOC2_CALL_VIA_RFC_DOCNUM in system <SM59 Destination>, message
Message no. IDOC_ADAPTER840
If I test the SM59 destination with Test -> Authorization it is successful. What do I need to configure to make it work?
Regards, Tanja

Hi,
Even though both are on same patch ..level..
please check the ALE settings..
In general..from Note..
In the ALE tools, a RFC connection is established to other systems at different points. Instead of a normal ALE IDoc transfer, this concerns synchronous calls that partly execute a dialog message in the target system.
Examples are distributing a distribution model view, ALE-CCMS monitoring or IDoc tracing.
Additional key words
ALE synchronous RFC RFC_DATA_DETERMINE_FOR_CHECKS
Cause and prerequisites
The standard system only allows for RFC destinations of type R/3 - R/3.
However, with regard to the Business Connector and in the era of connections via the Internet, for example, it might be useful and necessary to allow for other RFC types.
Nevertheless, this requires carrying out enhanced troubleshooting because other connections are more difficult to monitor and might display special error messages or not provide a dialog logon
Also see the below links..may be usefull..
http://help.sap.com/saphelp_erp2005vp/helpdata/en/d4/0d67e4d85511d2a6080060087832f8/content.htm
http://help.sap.com/saphelp_erp2005vp/helpdata/en/29/b134ce5cf311d289770000e8216438/frameset.htm
http://help.sap.com/saphelp_erp2005vp/helpdata/en/be/38f0d8cbfe11d2a5f80060087832f8/frameset.htm
Points rewarded if it is usefull..
Regards
Chilla..

Get the following error when trying to sync itunes to Nano itunes could not coppy " Song" to the ipod because unknown error occurred (-5000). Any ideas?

Get the following error when trying to sync itunes to Nano itunes could not coppy " Song" to the ipod because unknown error occurred (-5000). Any ideas?

Try my script FindTracks. Select a few of the missing files to start with then run the script. Choose No at the first prompt so that you can check how it works track by track, then confirm or edit the location of the media folder where your files are. Once you are happy with how it behaves let it process larger numbers of tracks automatically.
tt2

Issue Tracking List Error

Hello All,
I've created an Issue Tracking (Task) List for our company with a customized view. I had to change the width of one of the columns (Description) in SharePoint Designer in order to accommodate a large amount of text. I changed the default
view to this new, modified view.
Now each morning, the first person that accesses the list receives the following error:
Unable to display this Web Part. To troubleshoot the problem, open this Web page in Microsoft SharePoint Foundation-compatible HTML editor such as Microsoft SharePOint Desinger. If the problem persists, contact your Web server administrator.
Correlation ID: 6a01a375-2bc5-4ee0-b169-042da4858956
Could this be of my customized column width, and if so, how can I keep the customized column width without getting the error!
Thanks!!

Hi Benjamin,
The error can be caused by many reasons, so you need to check the ULS log for detailed error message.
For SharePoint 2010, by default, ULS log is at C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\LOGS.
In the meanwhile, you can clear the configuration cache for SharePoint to see if the issue still occurs.
To clear the configuration cache, please follow the link below:
http://blogs.msdn.com/b/jamesway/archive/2011/05/23/sharepoint-2010-clearing-the-configuration-cache.aspx
Please also check if the issue is caused by the KB2844286 Security Update on SharePoint 2010 as Cameron suggested.
Best regards.
Thanks
Victoria Xia
TechNet Community Support

Affiliate Tracking Security Error

Hello,
I have to integrate a tracking pixel into a flash-website.
My Solution was to do this with an URLLoad Request.
Code:
Security.loadPolicyFile("crossdomain.xml"); var url:String = "http://www.affiliate-geber.de/event.php?pid=1234&eventid=9898&referenz="+orderID+"&betrag="+nettoValue; var request : URLRequest = new URLRequest(url); request.method = URLRequestMethod.GET; var loader : URLLoader = new URLLoader(); loader.load(request);
I tried it also with URLVaraibles and allowDomain but all times I get the follow Error:
Error #2048: Security sandbox violation: http://www.myseite.com/flash/main.swf?version=1316675857 cannot load data from http://www.affiliate-geber.de/event.php?pid=1234&eventid=9898&referenz=0815&betr ag=1.99.
As Response I should only get “200 OK”, no Data.
Thank you for your help.

This is resolved.
I have copied the crossdomain.xml file to tomcat Root folder
and the issue is resolved.

CR52-A2 CD-RW (track following error???)

Similar Messages

Maybe you are looking for