Crap! Did I damage my firewire port?

Previous owner of a PC laptop and 4-pin FW that connected my m-audio fw-410. Needed to use the adapter to power the device.
Got my MBP with 6-pin and have been using the fw-410 but still connected to the adapter. I've heard that this is necessary when using phantom powered mics.
However, just poked around the m-audio website and found an article that specifically warned against using the adapter with apple computers that have 6-pin.
Would this instantly ruin my gear or port or is it precautionary due to an outside possibility of damage?
How would I know?
Here's the m-audio message:
- DO NOT USE the power supply when using your M-Audio FireWire audio interface with Apple computers!
The 6-pin FireWire port on your Mac supplies your M-Audio FireWire interface with power. Connecting a second power source (6-pin FireWire port AND Power Supply) can cause a variety of problems from installation failure to device damage. The power supply is intended for use when connecting to 4-pin FireWire ports that do not supply bus power. Apple Macintosh computers do not use this type of FireWire connectors and for this reason, you should never use the power supply with a Mac.

I guess it is. It still recognizes drives and still pumps sound through the device. I suppose that stupid me can assume it's okay and I dodged a bullet?

Similar Messages

I have a mid 2007 iMac w/ mac OS X Lion 10.7.5. My time machine (LaCie) is not responding through firewire port (since day one). Did an update mess this up?

I have just recently realized that my time machine has not backed up in a couple of weeks. I am using a LaCie external hard drive that I purchased with the iMac and has been plugged into the firewire port since day one. When I try to establish a connection it only gives me airport utility. When I look through network connections it shows that my fire wire is not connected or at least it doesn't find anything connected.
I have also been getting a start up disk message off and on that I need to close applications due to no more memory? (or something similar to that).
Just curious what might have changed. Did an update re configure something? Are these two issues connected?
I have always loved my Mac for the fact that it just always worked. I'm not super savvy with computers and the settings so I'm not the kind that just goes in to tweek things. This is the first real issue that I have had with it. I would think that it was the fact that I upgraded to lion but I did that quite a while ago.

Hello,
It isn't the fw in Network you want o use or look at, that's for something completely different.
My first suspect is the Power Adapter on the LaCie has gone.
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware>Firewire, what is listed there?
Reset the Firewire bus
If your Firewire or USB isn't recognizing any device. A solution which has worked for some whose hard drive became invisible in 10.4 was simply to follow these four steps to reset the Firewire/USB bus:
1. Shut the machine down.
2. UNPLUG the power lead to the computer and any firewire/USB drive or devices.
3. leave it for 10 minutes.
4. Connect back up and reboot.
http://www.macmaps.com/firewirebug2.html

G4 firewire port is damaging external drives

My 400 MHz G4 tower has suddenly started killing the firewire ports on my external drives (four in total). I found out I have what is known as a "killer firewire port". Has anyone else ever heard of this and If so can I fix this problem by simply installing a new firewire port PCI card on my G4?

Hi
If a firewire port or connector is poorly manufactured or excessively worn due to lots of plugging and unplugging, it is possible for a power pin in the port to connect to a data pin in the connector, frying whatever's attached to the other end of the cable. Assuming the problem lies with the port and not the connector, a PCI card should solve the problem. I'm not sure whether you've tried using different cables to rule out the connector. You could see how much you can waggle the connector in the port (with everything switched off at the wall socket).

Firewire Port out to lunch! Formac Studio goes with it! Help!

There was a nasty thunderstorm last night in my area. My computer was off the entire time, but upon restarting hours later, I found both my firewire ports out. This morning, one of them came back to life- but when I plugged my Formac studio into it- it no longer is recognized. I tried a few different attempts to get the other port back into action- but no luck. Anyone with suggestions? Anyone have a similar problem with Formac Studio going dead (I did email Formac as well)
Thanks, Matt

I was having problems with my Formac, iSigh and 8 FW drives.
G5 2x Gighertz, 4gig RAM, two internal drives and the above.
Everything would work until I put the computer to sleep, upon wake-up, neither the isight or the formac would produce an image. Both were just black screens. I would have to unmount the drives, disconnect and reconnect all firewire to make them work again.
I have two firewire hubs, one connecting the isigh and the formac (connected to the FW 400 port) and the other to the 8 drives (connected to the FW 800 port).
After trying just about every combination between the iSight and the Formac, I used a different cable than the original cable with two magnets which the Formac uses and connected it to the Hub with the 8 FW drives. This got me to the point where all I had to do was reset the Formac and both the Formac and iSight would work without disconnecting and reconnecting all the FW devises.
But it also got me thinking what would happen if I used the Formac FW cable to connect the hub to the FW400 port. Maybe that cable would help stabilize the connection... Since it came with the Formac, maybe it would work better for video, right? Well, I connected the Formacs cable to the hub and to the FW400 port. The computer immediately shutdown! After that, neither the 400 nor the 800 ports work. The hub smelled like burned circutry and 3 of the 8 drives have damage to the file structure.
Needless to say I am fumming! What the **** is this cable from Formac? Why does it have what appears to be two magnets? and why would they sell this cable that has the potential to damage an entire system costing thousands of $$s?
I'm doing a file recovery now, but don't have my hopes high on that...
If this cable caused all this, Formac should be put out of business!

Firewire ports not responding to external drives.

I have a LaCie 250 gig and it was working fine until I plugged a power book into one of the firewire ports. Not only did my G4 not recognize the power book, it also stopped recognizing my external drive.
The .mac site said to unplug everything and restart the computer to reset the firewire ports. Which I did and nothing changed. Figured it was a lost cause so I used the USB instead.
Then, one day, I tried it again to see what would happen and it worked. The firewire went back to normal and everything was fine.
The other day, I plugged my Canon XL2 into the firewire port and it shut everything down again. So, now I'm without firewire and back to USB for my external drive.
The firewire DOES turn on the drive, it just doesn't recognize that there's anything plugged in.
Thoughts?

1. Shut-down your Mac, and unplug the power cord
2. Turn the power off on your external FireWire devices
3. Unplug the FireWire devices from the Mac
4. Wait for 5 min.
5. Plug the power cord to your Mac only
6. For PPC Macs: Restart the Mac while holding the Option-Apple-O-F, and keep holding until you get the ">" prompt, then release the keys
7. At the ">" prompt type:
      reset-nvram and hit the Return key
      set-defaults and hit the Return key
      reset-all and hit the Return key
the last command will restart your mac
8. Shut down your Mac
9. Connect all your FireWire devices to the Mac and turn them on
10. Restart your Mac.
All your FireWire devices should reapear, if not repeat the procedure
How to avoid the issue :
The only really proven way to avoid burning up a FireWire port is to connect all devices and to turn them on PRIOR turning on the Mac. Likely, one must unplug them and turn them off AFTER the Mac has been turned off. If you need to connect another device, then you're on for a shutdown of your machine...  It's a tad annoying but it guarantees that the FW ports won't be damaged.  Be careful when using self powered devices such as webcams, iPods, hard drives or hubs, as they can destroy the port pretty easily. Another thing is to avoid daisy-chaining hard drives.
When the FW port doesn't respond anymore :
In this case, peripherals won't be mounted upon plugging, and won't be displayed in Apple's System Profiler. The self powered devices will still be fed by the port, but won't respond either.  It happens that the PHY just hangs after a surge or a random problem. Once hung, the port will not respond any longer, it is possible to reset the component by going through the following steps :
1° boot the PPC mac in Open Firmware by holding [ Apple key - Option - O - F ] after the startup chime.  2° you'll get to a command prompt. the keyboard mapping will be QWERTY, so pay attention when you type the following :  RESET-NVRAM (enter)  RESET-ALL (enter)  3° Now the mac should restart itself and the port should function properly again.  If it still doesn't work, then it means that the PHY is damaged.
http://www.hardmac.com/articles/16/
From Kappy post:
922 is only used in dual drive cases to provide a "build-in firmware RAID support"
912 or 912+ is FW800, the "+" means USB2
911 is FW400
924 adds eSATA support along with FW400/800
MacSales, OWC Tech Support library is where I would go first, as they do tend to have or links to, firmware updates for Oxford.
From Wiebetech:
I just upgraded my Mac OS, and now I'm having trouble with my FireWire device. What can I do?
A: With nearly every OS update Apple releases, some external drives are not recognized after the update. The typical symptom is that the device will not mount but the volume is visible and grayed out in Disk Utility. This means that the device is working properly, but the OS does not recognize the volume as mountable. Sometimes the drive does not show up at all.
The first thing to do is to see if repairing Permissions with Apple's Disk Utility First Aid feature solves the problem. If not, try repairing the disk with First Aid. Another possible solution is to zap the PRAM. This is done with a keyboard command while rebooting. Restart your computer and hold down the Command, Option, P and R keys. Consult the Apple web site for details.
If this does not work, then try pushing the PMMU reset button on the logic board. Consult the Apple web site for locations of the button for your Mac. If the drive still does not show up, shut down, disconnect all peripheral devices, and boot from the Mac OS Installation CD. The later the OS version, the better. Do not reinstall the OS, but when the Installer is loaded up and ready to begin, go to the File menu and use the Disk Utility program. Connect the drive that is having problems, then start the Disk Utility application. If you see the external drive and it is not grayed out, you know the drive is okay. Run Disk First Aid on it anyway. Then run it on your internal boot drive while you are at it. When done, unmount the external drive and UNPLUG it! Then restart the Mac.
When the Mac has restarted and is running on the internal boot drive, reconnect the external drive.

BSODs lock ups and flakey firewire port - help ??

Okay I'm really getting fustrated over this laptop it's nearly 2 weeks old
and I've already had 2 BSODs the odd crash where the mouse moves but nothing
else around it works so a forced reboot was needed.
Today I had a BSOD all i did was run some untility from the taskbar called
network doctor or something.
error message:
PAGE_FAULT_IN_NONPAGED_AREA (no address information supplied)
STOP: 0x00000000050
someone suggested that I may have a memory problem or my page file is corrupt.
anyway here's a run down on what i've installed so far with my laptop.
- Installed all XP security updates and patches
- Installed Firefox 1.0.1 (don't trust IE6.0 yet)
- Installed iriver download manager (my mp3 player)
- Installed winamp 2.0 and Creative Notebook Cam.
I've ran a forced boot chkdsk and no problems found.
Another thing I found interesting was nearly everytime my laptop bsods I usually
find a a yellow marker over my 1394 net adapter (firewire port) in device mananger
("cannot start device") don't know if that's related or not. A reboot seems to
clear this yellow marker but I am rather unhappy BSODs are no laughing matter.
My laptop model is the Equium A60-181 (Intel P4 HT 3.2Ghz 512Mb RAM)
Anyone else had similar problems or recommendations?
cheers,
Richard S.

Hi Richard
I understand you that you are unhappy with this all problems but there can be a lot of reasons for that. In my opinion this can happened because of some unnecessary update or some drivers installed by third-party software that you installed on your notebook.
Please reinstall OS using Recovery CD. After firs boot check in device manager if there is some hardware problem. If not you than try to start Config free (Connectivity doctor) and some other Toshiba tools to check if everything is ok.
If everything is ok try to install SP2 if you dont have it on your machine (just SP2 and not separately updates and patches). I am not sure but some of A60 are delivered with SP2.
Install all your programs slowly and follow carefully what happened after every step that you done.

Why would the Firewire Port and/or External DVD-RW suddenly not work?

Hi, it's me again. I swear, I must be destined to just use Windows machines...
Anyways, I have a used/refurbished iBook G3 500MHz 320MB RAM Dual USB (1 Firewire)laptop running OS 10.2.8 that I bought a few months ago. I went and purchased an external Firewire/USB 2.0 DVD-RW drive as I only had a CD-ROM drive on my machine and I wanted the option to burn CD's or watch/read data from DVD's (I know that with my slow processor writing DVD's -other than data- would be a stretch and have other machines to do that with anyways so it wasn't a concern really). I received it and installed it, also installed the free version of Toast that came with it, and the drive worked fine. I have not needed to use the drive since then and have not used the laptop much at all since then really, but I do need to say that I did end up adding a new user account, though I can't remember if I changed the original Admin account and then still have the one I created myself when I first started the laptop after I bought it (had a fresh install of Jaguar on it, but I have no disk to re-install with if needed) or if I created a separate (new) account and ended up deleting the Original Admin accout (I know in Windows, you cannot delete the original Admin account but I do not know if that is the same for OSX or not). I did this as I wanted a master Admin account that I just wouldn't really use and then wanted the other as my main account (and use it to connect to my home windows network) and for some reason it would not let me put a check in the box to allow that account to do so (from either Apple or my user accounts) and so I know that my main user account now is set up to allow it (was it the old Apple user account or a new one, I can't remember- sorry).
Ok, so that is the back story to my problem, which happens to be this:
I just bought a new chip of RAM (512MB to make it a machine with 576MB RAM total) and as I had been looking at getting OSX Tiger (but didn't want to do it without the extra ram and had been considering Panther instead as well), I thought it was necessary if I wanted to not bog down my machine. I bought the Install Disks on DVD for Panther, as well as an upgrade disk (DVD again) for Tiger, therefore letting me use the External Firewire DVD-RW to install Panther, and if I liked I could go ahead and upgrade to Tiger (and if I didn't like it too much, or it slowed things down too much etc, then I could always go back to panther and have both available for future options). The extra RAM coming in handy here definitely.
So I was going to install the RAM today, and decided to go ahead and test out the External DVD to make sure it could boot from it (before making any changes to my system) and then go and install the RAM, and after that, install Panther to start... But I plugged all the cords and cables in, used my laptop with AC power even, and I could not get the External to show up at all... (kinda like the very current post right below mine but for the G4- it worked before, but now the firewire External just does not show up).
I only have USB 1.1 on this laptop obviously, and I don't even know if you could do a boot from an external with USB 2.0 if my laptop had it (the DVD player does). I was recommended to boot with an external firewire DVD or firewire to another machine with DVD capabilities to do the install. So my problem right now is getting slightly bigger, as of course, I can't seem to momentarily find the stuff that came with the External (spare USB cable to check and see if the laptop will recognize it at least with that and to show it is the firewire that is not working properly, or the disk that I used to install it -might have been only used to install Toast free version if it didn't need any drivers, but I don't know where that or the instructions for installation sheet currently is -- I am looking for it, but I have switched bedrooms just last week and I also seem to be missing a few other Windows laptop disks as well so there is a good chance that they are all together, I just need to figure out where, heh.)
I am waiting currently before installing the memory, though if I don't get the External working tonight, I may go ahead and do it first as at least I will have more memory on my laptop then, until I can get other stuff functioning and be able to do the Panther install.
But my main question is, is there something that would cause an installed external to suddenly not show up in OSX? Since I hadn't used it since that one day, and it was unplugged from the laptop itself, would that end up doing it, or more likely, the changing of the user accounts (though I have been trying to test it with different types of media and through both of my user account (which are both "admin" ones), though I do still have one of those being an account that was on there when the External DVD was first installed, so it really shouldn't have done this at all (one would think). So how big of a chance is it that the firewire has somehow gone dead and this is the main culprit to my wasting the past 4 hours on this???
I am currently scavenging around for an extra USB cable to try and test the External that way and will post the results when I can... I love the look and idea of macs, now I have a mac and want to upgrade it even, but why is it that whenever I attempt to use it after having not used it for a bit (and try to make the iBook feel better by using it more as I am sure it feels sad and alone sitting on the shelf while my Windows Laptop gets more attention), or try to fix it when it can be made better (and therefore used more often), the mac (all macs really), just seem to get all pissy and cause problems and make me spend hours upon hours trying to get things to work again??? You have to admit it, I am "mac cursed"... sigh I can program in 4 or 5 computer languages and am very advanced at many tech things (the ones I am not as good at I am still usually Average or Medium skilled) so it makes me wonder why I have so many tech problems with Macs when they are supposed to be the "easy" OS to use...

Actually, I think I have it all working now. After going back to the Plextor Website, I found out that the switch between the USB and 1394 ports only gets activated (switched over to the other) with you turn the device off first, move the switch and then turn it back on. I was sure that I had done this with the ibook, but maybe not as when I went back and did it with first the USB and then the Firewire cables, it did work. I definitely knew that I had not done this with the Windows laptop, the reason it would not have the USB work for me on it.
but back to the iBook, I was confused as it was only showing up as a DVD-ROM (which I guess is what they do until you actually open up the burning software to then be able to burn to it), and it also had the wrong Model #, which after more research, showed that it was the Internal DVD drive model version (PX-708A) compared to the actual model version (PX-708UF) which is the USB/Firewire (External) model. The firmware was really out of date as well (from June 2004 I think, v1.06) and they had v1.12 from Spet/Oct 2006 available so I went to get that (which was a hassle). They had nice easy Windows self extractor/installer packs, and then the BIN files for use for all systems (Sun OS/ Mac OSX/ Mac OS/ Linux etc as well as usable for Windows), and those needed a special Firmware Updater Application which was OS specific. Only I had the hardest time trying to get the OSX one as it would send me to a FTP site and not give me any clues as to which file(s) I needed to get and the Mac OS version was just for older 9.2 or below versions and didn't want to install under the OS Classic mode.
I ended up using my windows computer which made it easier to view with the FTP stuff as I have FireFTP in Firefox, and downloaded the files I thought I needed (to test out), and then realized my silliness, and just downloaded (as well) the Windows Auto Extractor/Installer as the Firmware is the same for all OS's, just the way to install/update it was different... So I hooked the DVD drive to my PC and updated the firmware, checked it out on here before moving it back to the ibook, where I checked that it still worked and had the new update version showing, which it did, and now I have my fully working and newly updated drive ready for the OSX installations... I had attempted to update my Jaguar system as well while online, but it had no new updates available (I guess those were all mostly Tiger updates that were just recently released).
I am now off to install my additional RAM, and after checking that it all shows up correctly, I will go ahead and do the Panther Install (and test it out and see if I like it or not).
For anyone that currently uses Panther on any mac, are there still any major problems I should know about before hand, or know about things that they have mostly fixed (like the issues with Firewire ports and External Drives that they had around the time Panther was first released for example)???
Thanks to all that helped... I now know to attempt an "eject" of any external HD (which I do have one that I will setup to use after I get Panther on the ibook) or CD/DVD drive instead of just unplugging the USB/Firewire cable.

Full Firewire Port Failure (three different machines : iMac Intel, iMac G5, Black Macbook)

I'm experiencing a failure of all FireWire ports on all of my three machines. I believe this problem began with a faulty external, FireWire powered hard drive from G-Tech. Here are all my specs, followed by a rundown of the order of events that has lead to this situation, followed by the various troubleshooting I have done.
Equipment :
iMac Aluminum Intel - 24" Mid 2007 - running OsX 10.5.8 - currently 1 FW400 and 1 FW800 ports disabled
iMac G5 - 20" - running OsX 10.5.8 - currently 2 FW400 ports disabled
MacBook - 13" black Early 2008 - running OsX 10.5.8 - currently 1 FW400 port disabled
2 500GB G-Drives (by G-Tech) - AC powered
1 5TB G-RAID Drive (by G-Tech) - AC powered
1 250GB G-Drive Mini (by G-Tech) - FW powered
Initial Setup :
1 500GB G-Drive connected directly to iMac Intel via FW800
1 500GB G-Drive connected to first 500GB G-Drive via FW800 (daisy chained)
1 250GB G-Drive connected to second 500GB G-Drive via FW400 (daisy chained)
1 5TB G-RAID connected directly to iMac Intel via FW800>400 adapter
Sequence of Events :
I had transferred some files to my G-Drive Mini in order to move them to my MacBook from my iMac Intel. I copied the files to the G-Drive Mini and ejected it normally and plugged it into my MacBook via FW400. The drive would not mount, and the power indication light would not go on. After experimenting with various connections and cables I was able to get the drive to power with FW400 and USB connected at the same time, but the drive would still not mount.
I then plugged the G-Drive Mini back into the 2nd 500GB G-Drive as it was previously connected via FW400. This action caused the G-Drive to immediately reboot and eject itself from my iMac Intel.
I then attempted to plug the G-Drive Mini into my older iMac G5 via FW400. Immediately upon plugging in, the computer shut down, and would not restart.
At this point I kind of started to freak out. I was unaware of the extent of the damage, but was upset that the FW powered G-Drive Mini had shutdown my iMac G5. I contacted G-Tech Support and they offered to replace the drive and instructed me how to manually reset the computer's SMC by opening up the iMac and finding the Cuda switch. This worked and the computer was able to start and function again, but the FW400 port seemed to be disabled.
I then tried to swap out configurations and drives on my iMac Intel to see if there was any cable problems, but doing so, slowly rendered all my FireWire ports useless. It's almost as if the act of plugging in the FW-powered G-Drive Mini started a kind of shortout chain reaction. I soon learned that none of my hard drives would connect to any of my three machines, with any kind of cable combination via FW400 or 800.
I am currently able to connect my 5TB G-RAID drive to any machine via USB, as well as my G-Drive Mini. I am unable to access the other two external hard drives, as one has only FW400 and 800 ports and the other's USB connection is not functional as well on any machine.
Troubleshooting Steps Taken :
I have on all machines, reset the SMC in the following methods. iMac G5 - manually, by opening the case and pressing Cuda switch. iMac Intel - unplug, hold power button, restart method. MacBook - unplug, hold power button, restart method.
I have also on all machines, reset the PRAM by the Cmnd + Opt + P + R method at startup.
I have also unplugged all cables / removed battery, from all machines and left alone for a period of at least 12 hours, then re-plugged in each device one at a time.
I have also restored my hibernate mode (through Terminal) on my iMac Intel to mode 3 and also turned on Virtual Memory in system preferences and set hibernatemode to mode 7, the restarted and attempted to plug in devices. The reason I even began to deal with the hibernate mode was because I had around the same time my ports began malfunctioning, installed the DeepSleep widget, which allows you to control your computer's hibernate mode. I thought that tweaking with this setting may have made my computer incapable of recognizing devices that were plugged in. I have since uninstalled the widget and experimented with different hibernatemodes to no avail.
I also have Repaired Disk Permissions and Repaired Disk on all my machines, from within my Admin User as well as from the OsX Install Disk.
Sometimes in my System Profiler (like right now for example on my iMac Intel) my computer is "Unable to list FireWire devices," but sometimes, no warning message comes up and it simply displays the appropriate Bus speed.
I also conducted a system restore using a backup from my 5TB G-Raid Drive via USB, to a date before these problems started, but my ports are still not working.
Summary :
I am looking at a situation where all my FW ports on all my computers appear to be disabled, and possibly also on my four external hard drives, with one possible USB port malfunction on one external drive. The only root of this seems to be a malfunctioning FW-powered external hard drive.
Is this possible? Has this happened to anyone else before? G-Tech assures me that it is impossible for my 250GB G-Drive Mini to draw enough power from a computer to permanently disable any ports, but I have tried all of the FW port problem troubleshooting steps and am at a loss.
I do not have AppleCare and would like to avoid bringing two iMacs, a MacBook and four hard drives to the Apple store and take my chances with the geniuses.
I would appreciate any help or advice you all have. Thanks for reading and for your support!

Ok. So if that was too confusing, I've re-labeled this post with letters for my hard drives and some mapping of the connectivity configurations I have attempted.
Equipment :
iMac Aluminum Intel - 24" Mid 2007 - running OsX 10.5.8 - currently 1 FW400 and 1 FW800 ports disabled
iMac G5 - 20" - running OsX 10.5.8 - currently 2 FW400 ports disabled
MacBook - 13" black Early 2008 - running OsX 10.5.8 - currently 1 FW400 port disabled
1 500GB G-Drive (by G-Tech) w/ no USB port - AC powered : A
1 500GB G-Drive (by G-Tech) w/ USB port - AC powered : B
1 5TB G-RAID Drive (by G-Tech) - AC powered : C
1 250GB G-Drive Mini (by G-Tech) - FW powered : D
Initial Setup :
C > FW400-800 adapter > iMac Intel
D > FW400 > A > FW800 > B > FW800 > iMac Intel
Sequence of Events :
D > FW400 > MacBook
I had transferred some files to my G-Drive Mini D in order to move them to my MacBook from my iMac Intel. I copied the files to the G-Drive Mini D and ejected it normally and plugged it into my MacBook via FW400. The drive would not mount, and the power indication light would not go on. After experimenting with various connections and cables I was able to get the drive to power with FW400 and USB connected at the same time, but the drive would still not mount.
D > FW400 > A > FW800 > B > FW800 > iMac Intel
I then plugged the G-Drive Mini D back into the 2nd 500GB G-Drive A as it was previously connected via FW400. This action caused the G-Drive to immediately reboot and eject itself from my iMac Intel.
D > FW400 > iMac G5
I then attempted to plug the G-Drive Mini into my older iMac G5 via FW400. Immediately upon plugging in, the computer shut down, and would not restart.
At this point I kind of started to freak out. I was unaware of the extent of the damage, but was upset that the FW powered G-Drive Mini D had shutdown my iMac G5. I contacted G-Tech Support and they offered to replace the drive and instructed me how to manually reset the computer's SMC by opening up the iMac and finding the Cuda switch. This worked and the computer was able to start and function again, but the FW400 port seemed to be disabled.
I then tried to swap out configurations and drives on my iMac Intel to see if there was any cable problems, but doing so, slowly rendered all my FireWire ports useless. It's almost as if the act of plugging in the FW-powered G-Drive Mini D started a kind of shortout chain reaction. I soon learned that none of my hard drives would connect to any of my three machines, with any kind of cable combination via FW400 or 800.
D > USB > AnyMachine
C > USB > AnyMachine
I am currently able to connect my 5TB G-RAID C drive to any machine via USB, as well as my G-Drive Mini D. I am unable to access the other two external hard drives, as one has only FW400 and 800 ports (A) and the other's USB connection is not functional as well on any machine (B).
Troubleshooting Steps Taken :
I have on all machines, reset the SMC in the following methods. iMac G5 - manually, by opening the case and pressing Cuda switch. iMac Intel - unplug, hold power button, restart method. MacBook - unplug, hold power button, restart method.
I have also on all machines, reset the PRAM by the Cmnd + Opt + P + R method at startup.
I have also unplugged all cables / removed battery, from all machines and left alone for a period of at least 12 hours, then re-plugged in each device one at a time.
I have also restored my hibernate mode (through Terminal) on my iMac Intel to mode 3 and also turned on Virtual Memory in system preferences and set hibernatemode to mode 7, the restarted and attempted to plug in devices. The reason I even began to deal with the hibernate mode was because I had around the same time my ports began malfunctioning, installed the DeepSleep widget, which allows you to control your computer's hibernate mode. I thought that tweaking with this setting may have made my computer incapable of recognizing devices that were plugged in. I have since uninstalled the widget and experimented with different hibernatemodes to no avail.
I also have Repaired Disk Permissions and Repaired Disk on all my machines, from within my Admin User as well as from the OsX Install Disk.
Sometimes in my System Profiler (like right now for example on my iMac Intel) my computer is "Unable to list FireWire devices," but sometimes, no warning message comes up and it simply displays the appropriate Bus speed.
I also conducted a system restore using a backup from my 5TB G-Raid Drive C via USB, to a date before these problems started, but my ports are still not working.
Summary :
I am looking at a situation where all my FW ports on all my computers appear to be disabled, and possibly also on my four external hard drives (A, B, C, D), with one possible USB port malfunction on one external drive (B). The only root of this seems to be a malfunctioning FW-powered external hard drive.
Is this possible? Has this happened to anyone else before? G-Tech assures me that it is impossible for my 250GB G-Drive Mini D to draw enough power from a computer to permanently disable any ports, but I have tried all of the FW port problem troubleshooting steps and am at a loss.
I do not have AppleCare and would like to avoid bringing two iMacs, a MacBook and four hard drives to the Apple store and take my chances with the geniuses.
I would appreciate any help or advice you all have. Thanks for reading and for your support!

Firewire port not working Mac Mini (G4 1.25ghz)

Hi,
The firewire port isn't working on my mac mini, I've tried several devices, but none are connecting. I was wondering if anyone else was having this issue and possibly a solution. The only software installed on the computer since the firewire worked last was Apple updates, so maybe other mini's lost firewire somewhere along the way.
Thanks, and Thanks
W

This worked from Smokerz in the Power Mac G4 forum:
1. Shut-down your Mac, and unplug the power cord
2. Turn the power off on your external FireWire devices
3. Unplug the FireWire devices from the Mac
4. Wait for 5 min.
5. Plug the power cord to your Mac only
6. For PPC Macs: Restart the Mac while holding the Option-Apple-O-F, and keep holding until you get the ">" prompt, then release the keys
7. At the ">" prompt type:
reset-nvram and hit the Return key
set-defaults and hit the Return key
reset-all and hit the Return key
the last command will restart your mac
8. Shut down your Mac
9. Connect all your FireWire devices to the Mac and turn them on
10. Restart your Mac.
Works fine now thanks Smokerz!!!!!
also repaired permission and reset PRAM, nothing worked until I did this.
W

My MacBook Pro can't find the FireWire port

My MacBook Pro (OSX 10.6.8) can not find the FireWire port. Until now there hasn't been any problems using the FireWire, but now it just deny any knowledge of it, so to speak.
The audio device lights up when I connect it to the MBP (yes, I did connect it when in off-mode), so it seems to work in a way.
Does anyone recognize this problem and knows how to solve it?
/JohanLaMar

Have you tried following through the trouble shooting tips in this knowledge base article on Firewire?

How can I tell if my firewire port is faulty?

I recently cannot import video from my canon elura 100 which connects using a 4-6pin firewire cable. I thought maybe it was the cable so I grabbed my brother's black macbook and it seems to import fine, it still isn't 100% smooth like I think it should be but when I plugged the camera back into my black macbook, the video that was being imported just kept freezing and it seemed warped. I tried this process a few times and kept getting the same results. I feel as though I may have a firewire port issue. How could I check on my own. I know that when I use my firewire 410, I have no problems so I don't know what could be wrong. Any help?

Did any of your problems start with Snow Leopard, is your brother's machine running the same version of SL.
Over in the audio forum there are those having some problems with their firewire interfaces. (glitches, static...etc)
pancenter-

Imac G5 won't start with Isight plugged into the firewire port.

I went to turn on my Imac today and it wouldn't start. After checking all the usual culprits (power strip, outlet and power chord) which were not the problem, I proceeded by unplugging all the external devices from the back ports. After unplugging the computer for a few seconds and plugging it back in (which I read resets any power issues), it turned back on. I plugged my Isight camera back in and turned it on and the computer suddenly shut off. I reproduced this quite a few times and it did the same thing. It won't even turn on if any device is plugged into the firewire port. Does anyone have a clue of what this conflict could be or experienced anything similar.
I would greatly appreciate any input.
Thanks in advance,
Daniel

Welcome to Discussions - try resetting your PRAM, if that doesn't work, I'm afraid there is something wrong with your logic board, where the firewire bus is located. The best thing to do would be to take it in for servicing.

How to transfer files from an iMac without upgraded Migration Assistant to a new iMac that doesn't have a firewire port?

Hello.
I just purchased a new iMac. He's awesome. However, he didn't come with a Firewire port. (Bummer, because I have one from the last time (2007) I had to transfer stuff from my iBook...)
When I turned him on, he wanted to use Migration Assistant to transfer files from the older iMac; she doesn't have the most updated Migration Assistant, though. (She works just fine, but she only has Snow Leopard.)
Okay, so what I'm wondering is if I just have to use a huge external hardrive to move everything? If I do that, will my programs (Microsoft Office) move? I fear they won't move/transfer that way. Ugh.
PLEASE HELP.
Ideas? Advice?
Thank you in advance!

Firewire 800 (what the new iMac has) is 9 pin. FireWire 400 is 6 pin (what your old iMac has). Hopefully you didn't damage your new iMac by trying to insert a FW400 cable into its FW800 connector. The numbers are important in the case of the ports. They don't interchange!!! Get the proper cable or risk damaging your new iMac.

Firewire port does not always work to import movies from video camera

I've been having issues with my Mac Pro lately, it is an 06 model. Opening up iMovie and starting the import process for video from my Canon camera, the software will not recognize that the camera is connected.
In system profile I do see that the camera is connected via the fire-wire port and shows the correct name, etc.
After a bit of troubleshooting, restarting software, I unplugged the fire-wire connector that is part of the dongle coming from the 23" cinema display and the camera appeared like it should.
System profile indicated that the fire-wire connection from the 23" display was unknown. I do know that I can plug other items into the display and they work fine.
Rebooting the Mac Pro did not have any effect either.
Granted, it is working, but I wish I did not have to unplug the cinema display port each time I want to do this.

The firewire port on the Display does not have enough internal power requirements to support some devices. Try the firewire port on the back of the Mac Pro. If you are using a firewire repeater then don't connect it to the Display firewire port, use the Mac pro.

IMac firewire port is not working

iMac firewire port is not working
Hi everybody, Happy New Year.
I am a 72 years old semi-newbie in video editing, because Iedit only 1 or may be 2 movies a year since 2007 and I have only very little computer knowledge.
I received a new 27” iMac as a birthday gift 14 months ago. About 10 months ago, with help, I successfully use the Migration Assistant to transfer some datas from my old power G4 to the iMac including two Final Cut Express projects. I had one project successfully done; burned to DVD and I save it with Print To Video. Last week, I have my second project done, I burned the sequences into DVD but unable to do a Print To Videodue to the iMac is not communicating with my Sony camcorders DCR VX1000, this is the same camcorder I used on the last job which was working a couple of months ago.As a result, I try to switch the Easy Setup with different Format and different Use; I refresh the Canvas window; I did a Mix down; move the Screen Saver to NEVER as well as the Energy Saver set to NEVER SLEEP. I also trashed the preferences (plist) folders; run the Utility repair, I replaced the firewire cable (4 pines – 9 pines 800), but nothing work. Up to this point, I think that there is no signal from the firewire port to the camcorder because I understand when the sequences is ready, the firewire is connected between the computer and the recording camcorder, the Print to Video is activated, then the word DV- IN should be seen on the recording deck screen. This time, I don’tread such words on the recording screen. Therefore, I think there’s no out going signal from the iMac to the recording camcorder and the iMac is not receiving signal from the recording camcorder. At this point, I try to connect my iMac to the power G4 to see if I can do some data transfer. Follow the procedures, I hook up the data transfer cable between the G4 and the iMac, I can the fireswire icon moving on the G4 screen but no indication on the iMac screen (there should be some indications in the source bar), this shows me the iMac did not recognize the G4 which worked on previous data transfer. It looks to me the firewire port on my iMac is dead. What has gone wrong? Could I accidentally disabled the firewire port by some magic keystroke? (i.e. accidentally fat finger some thing to make it stop working? Oh, by the way, during the playing around, went to the Final Cut tool bar, I click the View >Video Out > Digital Cinema Desktop Preview – Main, the result was a black screen and the esc key was my rescuer - LUCKY LUCKY! Are there any other trouble-shooting techniques to apply before bringing to shop? Please help!
Sorry for such a long statement, forgive me for unable to make it shorter. Thank you for your patience. Thanks to all the folks in this board for being so helpful.
p.s.

Not sounding good.
If the system Profiler does not see it then there is a basic communication problem between camera and the Mac.
I'm thinking the Firewire port is the culprit as some 800 ports were faulty.
I'd suggest taking the Mac, cable and camera to your nearest Authorized Apple Service Centre and get them to diagnose the issue. eg. let them try to connect the two devices.
Right (control)click the Sequence icon in the Browser and select Item Properties, do the same for a clip.
You can also post screen shots for the Properties.
Al

Crap! Did I damage my firewire port?

Similar Messages

Maybe you are looking for