Create ISO of Windows Server 2012 R2 Physical Server - NOT VM

I have a windows server 2012 R2 installed on a physical server. I have windows patches and other firmware upgrades on it. I would like to create a gold image in the form of ISO, so that i can use this ISO and build my other servers. I have read many many
blogs but none of them have clear steps. I know there are tons of ways to do this for VM, but this is for a physical machine. I have used sysprep, completely messed up my server, i am used there is no warning or anything listed on technet for using this software.
If anyone has able to do this successfully please let me know. Please don't send me instructions for VM, this is not a VM, it is a physical server. Thanks in advance.

Okay, it's been a while since I worked with MDT and my memory was bad. The best thing to do is to download MDT (https://www.microsoft.com/en-us/download/details.aspx?id=40796
for the 2013 version) and its documentation. One of the documents is a Quick Start Guide. It gives you step-by-step instructions on how to do what you are asking. It doesn't make sense to replicate all that content in a forum when there is
already a published document.
Then, if you have problems with performing the tasks, come back to this forum and ask specific questions about the issues you are encountering.
Note, the documentation assumes working with Windows 8.1, but it also says it supports it for Windows Server.
. : | : . : | : . tim
Thanks Tim. I started working on it, i do have few questions:
i) Why do i need 3 machines as per the document "Quick Start Guide for Lite Touch Installation.docx"? I am not quite following here, can i just do it on 2 servers, 1 which will capture the image and server 2 will be used to build using captured image.
ii) I was able to get till Step 41. (page 17 from doc 'Quick Start Guide for Lite Touch Installation.docx'), i do see the ISO created, but it is only 300 MB? My original ISO was 4 gb. I don't think i can just copy the 300 MB iso and build another machine, i
am lost here, any advice is appreciated.
Thanks

Similar Messages

Error in creating Failover Clutser - Windows Server 2012 R2

Hello,
I have created a single node Failover Cluster in Windows Server 2012 R2. When I am trying to add second node to this cluster, it gives the error: “Cluster
service on node Node1did not reach the running state. The error code is 0x5b4. For more information check the cluster log and the system event log from node Node1. This operation returned because the timeout period expired.
The server 'Node1.mydomain.com' could not be added to the cluster.
An error occurred while adding node 'Node1.mydomain.com' to cluster 'My_Cluster'.
This operation returned because the timeout period expired.”
I have attached the screenshots of Event ID.
Firewalls are turned off on both servers (Node1 and Node2). I have successfully created single node clusters on both servers, but when I try to add second node, it
gives error.
Before starting the creation of new cluster I don't forget to Destroy previous cluster and run "Clear-ClusterNode".
Every time they successfully pass the Validate Configuration Test, but give the error on creating failover cluster.
I'm using the service account which has full permissions on CNU and both nodes, plus it has permissions to create computer accounts in AD.
Can anyone please help?
Thank you.
Best regards,
Hasan Bin Hasib

Thank you fellows!
The issue just resolved when I moved the Node1 and Node2 on the same host, and the cluster was successfully created.
After the creation of cluster, as soon as I moved the Node2 to some other host, then the Failover Cluster Manager console started showing Node2 is Down. Error: Cluster node Node2 could not to join the cluster because it failed
to communicate over the network with any other node in the cluster. Verify the network connectivity and configuration of any network firewalls. Event ID: 1653
IP Address of Node1: 172.16.1.186 ; IP Address of Node2: 172.16.1.187
And yes, the ‘Microsoft Failover Cluster Virtual Adapter Performance Filter’ is already disabled on all virtual adapters. All firewalls are disabled, no antivirus installed. I’m using same type of NICs.
I don’t know where the blockage is, and I am badly stuck. Please help.
Thank you.
~ Hasan Bin Hasib

Windows server not shutting down

Hi guys,
We have installed and configured correctly a PI 7.0
system on Windows 2003 Standard Edition X64-bit with SQL Server 2005.
We are on SP12. Everything, SLD, RFC connections work properly.
The problem was that 4-5 days after the installation the Windows Server
started restarting automatically in unexpected time during the day
(unexpected shutdown), even when anybody didn't do anything in the
system.
SAP suggested us to upgrade firmware, network card and
memory, which actually solved the problem.
However, the problem that we are facing right now is that the Windows
Server is not shutting down. That is, we are trying to shut down the
operating system, but it never does so.
SAP suggested us that it could be a service
which is defined as restart ever, and to try commands shutdown -s/-r -t 00 -f
from CMD, but no result. The server is trying to shut down or restart unsuccessfully.
It remains in a grey page and is trying to shut down itself.
This is a production system and we go live on 01/01/2008! Do you have
any ideas?
Best Regards,
Evaggelos

Hi guys,
We have installed and configured correctly a PI 7.0
system on Windows 2003 Standard Edition X64-bit with SQL Server 2005.
We are on SP12. Everything, SLD, RFC connections work properly.
The problem was that 4-5 days after the installation the Windows Server
started restarting automatically in unexpected time during the day
(unexpected shutdown), even when anybody didn't do anything in the
system.
SAP suggested us to upgrade firmware, network card and
memory, which actually solved the problem.
However, the problem that we are facing right now is that the Windows
Server is not shutting down. That is, we are trying to shut down the
operating system, but it never does so.
SAP suggested us that it could be a service
which is defined as restart ever, and to try commands shutdown -s/-r -t 00 -f
from CMD, but no result. The server is trying to shut down or restart unsuccessfully.
It remains in a grey page and is trying to shut down itself.
This is a production system and we go live on 01/01/2008! Do you have
any ideas?
Best Regards,
Evaggelos

Windows server not seeing jdk1.5

Hi, I just installed 1.5 jdk on a Windows server that had 1.4. I changed the PATH to point to the 1.5 \bin, but 1.4 is still showing up when I check java -version.
Why is the system still pointing to 1.4? Thank you.

Check the registry entries. And how did you change the path?

How do I stop Mac creating files on Windows server creating hidden files?

I have my macbook connecting to a windows 2003 server share. Whenever I write a file, either by creating or editing and saving, it creates a hidden file too. I edit filename.doc then I'll also have ._filename.doc in that directory. It's distracting the windows users and causing me to become a little unpopular. How can I prevent those hidden files from being created?

This happens in part with some Mac files that contain both a resource and a data fork. Windows doesn't know how to handle these files and breaks them apart. Also, Mac OS creates certain hidden files used by the Finder that also get transferred but are no longer hidden on Windows because Windows does not recognize the "." preceding a filename as the Unix shorthand for "invisible."
There are a number of free utilities you will find at VersionTracker or MacUpdate that can prevent this and the hidden files from appearing on the Windows drive.
Zipping files before transfer will also prevent the problem from occurring.

Creating Group Policy Windows Server 2008 R2

Hello guys,
I want to implement a group policy/policies across the network to perform the following;
1) Restart users PCs across the network on the last Friday of every month
2) Update the PCs with Microsoft patches or updates if any during the restart
3) Send a notification message on
Wednesdays preceding that Friday to the users, informing them to save their work and close all the programs and files as their PCs will be restarted on Friday.
Any help on this would be greatly appreciated.
Thanks in advance
Cheers

Hi Sudhirhk,
You can configure a GPO via a script or schedueled task of GPP to restart PCs. Please refer to the following similar case:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/3608dd77-3727-4cc6-b3c6-cfcf1a486a2a/restart-computers-via-gpo?forum=winserverGP
What's more, you can also use schedueled task to send notification messages at the appointed time, please refer to the following similar case:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/34f06393-7a8a-4c29-bd2d-726266a55130/scheduled-task-email-notification-server-2012?forum=winserver8gen
In addtion, as for the updating, please refer to the following article:
Configure Automatic Updates by Using Group Policy
Please apply the GPO according to your requirements.
Regards,
Lany Zhang

Windows Server 2012 GPO setting are not apply on windows Xp clients

Hi
I am create GPO on windows server 2012. 300 clients on domain are working fine, GPO setting apply on all windows 7, 8 clients. But 200 clients of windows XP are not working. GPO setting are not applies on XP. I am trying to Group Policy
Preference Client Side Extensions for Windows XP (KB943729) on one window XP client, all GPO servers 2012 setting is working fine. But is not solution. I have 200 clients of windows XP, Please provide batter solution on one click command and apply all 200
XP clients.
Thanks.

Dear,
I have Windows server 2012 , i have install ADDS with Forest functional level 2008 & Domain functional level 2008 .
I have applied GPO to particular OU, when i login to domain user on Windows 7 PC all GPO working fine but when i login on Windows Xp SP3 PC its not applied on XP.
I am facing issue on windows XP clients it is true. Please see this URL address:
http://blogs.technet.com/b/grouppolicy/archive/2009/03/27/group-policy-preferences-not-applying-on-some-clients-client-side-extension-xmllite.aspx
Please provide batter solution on one click command
Thanks.

Using Windows Server 2012 VL Product key with Windows Server 2012 R2

Hi all,
Trying to use a Server 2012 vl product key to active a Server 2012 R2, but running into issues, namely it is not accepting the key. I have read many threads pointing out that different keys are required, but no mention of the process that one needs
to take in order to obtain/swap product keys? Any ideas appreciated? :)

The product key I have is for Windows Server 2012 Standard VL, (It's not a DC).
I have downloaded the evaluation iso for Windows Server 2012 R2 and want to licence it (with a VL), but it is failing with the Windows Server Standard 2012 VL product key.
My question is - am I doing something wrong, or do I need to ask Microsoft to change the product key / buy a new one? - What steps do I need to take?
The product key for WS2012 will not work for WS2012R2. (so, yeah, you're doing that wrong)
WS2012R2 is not a "free" upgrade from WS2012 (it's different to Win8.0 -> Win8.1)
Your WS2012 pkey will work with WS2012. To use WS2012R2 you need a WS2012R2 pkey.
If you want to "convert" an evaluation license install, into a full licensed install, you must match the version (2012 vs. 2012R2) and the edition, and must use DISM as well as the correct pkey.
http://technet.microsoft.com/en-us/library/jj574204.aspx
If you don't have the correct pkey for WS2012R2 already, and you don't have one waiting for you in the Volume Licensing Service Center website, you'll need to purchase a new license for WS2012R2.
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

Rstrui.exe Create a system restore point on windows server 8 standard

Hi,
Before making system changes, I need to create a system restore point on windows server 2008 Standard with SP2 installed., I found where to accomplish that via the UI, but the file isn't found when I search the C:\windows directory on the server.
The executable should be C:\windows\system32\rstrui.exe, unless it was changed for Server 2008. I have system protection turned on for the C: drive.This problem also exists on Windows server R2 enterprise with all updates applied.
I searched the install media (DVD) it wasn't there. I tried the full name (rstrui.exe) as well as truncated versions. I've searched on all of the applicable forums for rstrui.exe and "create system restore point".
Does someone know where I can get rstrui.exe for windows server 8. It's not available on windows server R2 enterprise or essentials either. If there is an alternative method of creating restore points on windows server 8, please point me in the
correct direction. Is it available in any of the variations of windows server 12. I have all of the updates installed when checking for how to create a system restore point or with searching for rstrui.exe. BTW, performing "system backups" or implementing
"previous versions" functionality work just fine.
Thank you in advance,
Steve

Hi Steve,
I replied the same question you posted earlier:
https://social.technet.microsoft.com/Forums/en-US/68352496-2fe8-4320-8848-f22d0d1a6f6b/rstruiexe-missing-unable-to-create-restore-point-windows-server-8-std-r2?forum=windowsbackup
To me it seems that the function is removed in both Windows 2008 SP2 and Windows 2008 R2. Here is my original reply:
I did not find this file either on my new-installed Windows 2008 SP2 system. I assume it is retired in Windows Server 2008 and the function is replaced by Windows Server Backup. I cannot confirm why there is still an option in MSCONFIG which point to
rstrui.exe but I can find the file nowhere. Also this option is removed in Windows Server 2008 R2.
Here link a link for using Windows Server Backup to create system state backup as a restore point:
Recover
the System State
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Trying to download windows server onto my computer.

I was able to burn an ISO for Windows Server 2012, but every time I try to download it says either my pc has encountered a problem and need to shut down or it issues a compatibility report. I follow the directions for report and then my computer reboots.
Could my computer not be able to handle it?

Hi,
Do you mean that you cannot download Windows Server 2012 ISO file on your computer? If so, please try the link below to see if the ISO file could be downloaded correctly:
Download Windows Server 2012
http://technet.microsoft.com/en-us/evalcenter/hh670538.aspx
In the meantime, please provide the detailed information of the error message when you download the ISO file.
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Error install software on Windows Sever 2012

Hello!
I'm using a VPS Cloud. used OS Windows Sever 2012.
I can not install any
software on it. Simple as firefox, error: Cloud not find...runtime or adobe flash player...ect.
Please help me install.
Thank you
Regards
Danny |

So, if I understand correctly, you have cloud hosted servers (Server 2012) and you're trying to manage via ConfigMgr 2012 (install software etc).
1. Are these servers part of your domain?
2. What connectivity is there to the servers?
3. Have you created a boundary for the servers and added to a boundary group?
4. Have you successfully installed a ConfigMgr client and it is reporting correctly?
Gerry Hampson | Blog:
www.gerryhampsoncm.blogspot.ie | LinkedIn:
Gerry Hampson | Twitter:
@gerryhampson

Windows Server 2008 Active Directory Trust

Hi ,
Can anyone help with the answer to the following questions please?
a) Whether Microsoft Windows Server 2008 SP2 Standard Edition support AD trust relationships (one-way; two-way)
b) Whether we can create trust between Windows Server 2008 R2 SP1 and Windows Server 2008 SP2 Standard Edition AD servers?
Thanks in advance.
India1947

Hello,
First of all, please confirm the firewall on the Windows Server 2008, the TCP/IP filter or any 3 party firewall is not blocking the RPC and ICMP traffic between two domain controllers.
1.    Have a test of creating and verifying trust while all firewalls are all disabled. Then re-create and verify the trust to check how it works.
Allowing Inbound Network Traffic that Uses Dynamic RPC
http://207.46.196.114/windowsserver2008/en/library/d37f96c6-c729-4b29-80a9-88db3d97b8631033.mspx
2.    If it still fails, please try to collect the following information for our further investigation:
-      Run "Netdiag /v >>netdiag.txt" on both DCs
-      Network Monitor trace when verifying the trust:
Download the NetMon3.1 from the following link:
http://www.microsoft.com/downloads/details.aspx?FamilyID=18b1d59d-f4d8-4213-8d17-2f6dde7d7aac&DisplayLang=en
1.    Install the NetMon on Windows Server 2008.
2.    In the Microsoft Network Monitor 3.1 window, click Create a new capture tab….
3.    In the new tab, select all the Network Adapter in the Select Networks window.
4.    After that, press F10 to start NetMon.
5.    In the Active Directory Domains and Trusts, try to verify the trust to reproduce the issue.
6.    After that, go back to the Netmon window and press F11 to stop the Netmon on the Windows Vista machine.
7.    Press Ctrl+S to save the Netmon files.
Please send files to [email protected]
Note:
a. Please include the following three lines for this issue in the email body:
Trust Windows Server 2008 and Windows 2000
http://forums.microsoft.com/TechNet/ShowPost.aspx?PostID=3210801&SiteID=17
Miles Li - MSFT
b. We will continue to discuss the issue here in the newsgroup and will NOT reply via emails.
c. Pease post a quick note in the current thread to inform me after sending the email.
Thanks.

Window Server communications from outside of session allowed for root

Hi ,
When I am running the following program, i got the exception as
49:wasp.corp.apple.com_kevinli:/ngs/app/giat/src/java/chart> java MyFrame
kCGErrorRangeCheck : Window Server communications from outside of session allowed for root and console user only
Exception in thread "main" java.lang.InternalError: Can't connect to window server - not enough permissions.
at java.lang.ClassLoader$NativeLibrary.load(Native Method)
at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1586)
at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1503)
at java.lang.Runtime.loadLibrary0(Runtime.java:788)
at java.lang.System.loadLibrary(System.java:834)
at sun.security.action.LoadLibraryAction.run(LoadLibraryAction.java:50)
at java.security.AccessController.doPrivileged(Native Method)
at sun.awt.NativeLibLoader.loadLibraries(NativeLibLoader.java:38)
at sun.awt.DebugHelper.<clinit>(DebugHelper.java:29)
at java.awt.Component.<clinit>(Component.java:506)
at MyFrame.<clinit>(MyFrame.java:6)
import java.awt.*;
import javax.swing.*;
public class MyFrame
public static JFrame f = new JFrame();
public static void main(String[] args)
JFrame.setDefaultLookAndFeelDecorated(true);
f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
//Add the ubiquitous "Hello World" label.
JLabel label = new JLabel("Hello World");
f.getContentPane().add(label);
//Display the window.
f.pack();
f.setVisible(true);
Please send a reply on this.
with regards,
Mohan

Seth,
you may also install the latest update (10.4.6) using the combo file from apple.com.
Mihalis.
Dual G5 @ 2GHz Mac OS X (10.4.6)

Create a customized bootable ISO to install Server 2012 on a physical or VMware server

Management would like us to create a pre-customized bootable 2012 ISO image. I'm using previously created work instructions on how to create a 2008 R2 image which is used to boot on a physical server and also used to deploy VMware servers. We
install some applications that we use in our standard builds and create the ISO.
So for a 2008 image we customize the 2008 server build using using a pre-created Autounattend file.
We install all the applicaitons, remove guids and use a customized unattend to sysprep (/oobe /generalize)
We use a pre-prepared Pre Sysprep PE disk to create the Wim file.
We use DISM to mount the WIM and add drivers.
We use imagex to split the wim file into sim files if the wim file is more than 4GB
We use a pre-prepared Post Sysprep ISO to add the wim or sim files to create the ISO.
Now with the requirement for deploying 2012 we have been asked to duplicate the same process. I'd prefer to use a VMware image, clone or template so we don't have to start the build process all over each quarter as we need to update this image quarterly.
We would use the VM template for VM's (and that's been the easy part). But I'm not sure of all that is required for the physical image ISO. I want to completely remove the physical server out of the picture except for the deployment option
to a physical server. In other words create the wim file from the customized 2012 VM server.
I know we have to get the unattend files from AIK 8 or 8.1 and I think we need to use AIK to get a Pre Sysprep PE and Post Sysprep ISO but an not completely clear how to do this.
Can someone steer me in the right direction or provide any tips or gatcha's?
Thanks!

Hi MHDay,
1.Install the Deployment Tools feature included in the
Windows Assessment and Deployment Kit for Windows 8. 2.Extract your Windows 8 ISO
3. Launch the Windows System Image Manager
4.Under Windows Image right click and select a windows image, navigate to the sources\install.wim file from your extracted ISO or your DVD
5.It will ask you about creating a catalog of the image, say yes
6.Once that is done, under Answer File right click and select new answer file
7.Drag Microsoft-Windows-Shell-Setup_neutral to the "4 specialize" section
    a. Enter your product key
8. Drag Microsoft-Windows-International-Core_neutral to "7 oobeSystem"
    a. Set InputLocale to 0409:00000409
    b.SystemLocal, UILanguage, and UserLocal all to en-US
9. Drag Microsoft-Windows-Shell-Setup_neutral to "7 oobeSystem"
    a. In order to make the installation completely silent and not need any user interaction, under OOBE set each of the following to true: HideEULAPage, HideLocalAccountScreen, HideOEMRegistrationScreen, HideOnlineAccountScreen, HideWirelessSetupInOOBE
    b. Set NetworkLocation to Work
    c. Set ProtectYourPC to 1 (This enables windows update with recommended settings)
10. If you do not specify a local account in the answer file you will be forced to create one during image deployment, so be sure to create a new Local Account under UserAccounts -> LocalAccounts
    a. I have found that you can create a new account that is the same name as one that is already in the image for simplicity
11. If you need to join to a domain, drag Microsoft-Windows-UnattendedJoin_Neutral to "4 specialize"
    a. Set your domain name in JoinDomain, set UnsecureJoin to false
    b. Enter credentials with domain join privileges -- **They WILL be stored in plain text in the file
Save your unattend.xml file. At this point if you are using WDS you can select the image in the WDS console and attach the unattend.xml file to that image.
If you want to slip the unattend.xml file in to the image itself, copy it to c:\windows\system32\sysprep, and run sysprep like this: sysprep /generalize /oobe /shutdown /unattend:c:\windows\system32\sysprep\unattend.xml
For details please refer to
here.
Then you may follow your steps to create ISO file .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Windows Server 2012 Windows Backup failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).

The Volume Shadow Copy service initially was running under the context of System, so we thought that ‘System’ doesn’t have permissions to access network shares.
When the Volume Shadow Copy service was running under the context of System, this was the error logged:
“failed with following error code '0x8078014B' (There was a failure in creating a directory on the backup storage location.).”
Which is likely due to not having permissions to write to the network location.
This is a scheduled backup trying to write to a network location, so we changes the service to run under the context of an account that does have permissions to write to the network share.
  Then the error changed to this:
“failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).”
HRESULT 0x8078006b
DetailedHRESULT 0x8004230f
ErrorMessage %%2155348075
BackupState 12
VolumesInfo <VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0"
BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0"
TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228"
DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0"
FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0"
/></VolumeInfo>
We aren’t really seeing anything that gives any hint on what the issue is.
Any ideas? Thanks in advance!

We are trying to back up folders/files from 2 local drives (C: & D:), both of which have only 10% space used, and 100 GB free.
We are attempting to back the files up to a Remote Shared File (and there is 100+ GB free space out there).
  If we try another network location, we receive the exact same error.
This is Windows Server 2012, not running Hyper-V and is a physical server not a VM.
Thank you for the link.
Looking in:
Event Viewer / Application and Service Logs / Microsoft / Windows / Backup / Operational
But it doesn’t seem to give any more details:
Log Name:
Microsoft-Windows-Backup
Source:
Microsoft-Windows-Backup
Date:
7/8/2013 8:00:12 PM
Event ID:
5
Task Category: None
Level:
Error
Keywords:
User:
SYSTEM
Computer:
servername.edu
Description:
The backup operation that started at '‎2013‎-‎07‎-‎09T02:00:06.273000000Z' has failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).
Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Backup" Guid="{1DB28F2E-8F80-4027-8C5A-A11F7F10F62D}" />
<EventID>5</EventID>
<Version>3</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2013-07-09T02:00:12.872602100Z" />
<EventRecordID>30</EventRecordID>
<Correlation />
<Execution ProcessID="3028" ThreadID="3996" />
<Channel>Microsoft-Windows-Backup</Channel>
<Computer>servername.edu</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BackupTemplateID">{A421E864-A115-4288-8D12-F4878CF8A248}</Data>
<Data Name="HRESULT">0x8078006b</Data>
<Data Name="DetailedHRESULT">0x8004230f</Data>
<Data Name="ErrorMessage">%%2155348075</Data>
<Data Name="BackupState">12</Data>
<Data Name="BackupTime">2013-07-09T02:00:06.273000000Z</Data>
<Data Name="BackupTarget">\\servername\BACKUP</Data>
<Data Name="NumOfVolumes">2</Data>
<Data Name="VolumesInfo"><VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0"
IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem
Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0"
NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /></VolumeInfo></Data>
<Data Name="SourceSnapStartTime">2013-07-09T02:00:06.289250300Z</Data>
<Data Name="SourceSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="PrepareBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PrepareBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="TargetSnapStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="TargetSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="DVDFormatStartTime"><TimesList></TimesList></Data>
<Data Name="DVDFormatEndTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyStartTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyEndTime"><TimesList></TimesList></Data>
<Data Name="BackupPreviousState">2</Data>
<Data Name="ComponentStatus"><ComponentStatus></ComponentStatus></Data>
<Data Name="ComponentInfo"><ComponentInfo></ComponentInfo></Data>
<Data Name="SSBEnumerateStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBEnumerateEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SystemStateBackup"><SystemState IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="BMR"><BMR IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="VssFullBackup">false</Data>
<Data Name="UserInputBMR">false</Data>
<Data Name="UserInputSSB">false</Data>
<Data Name="BackupSuccessLogPath">
</Data>
<Data Name="BackupFailureLogPath">
</Data>
<Data Name="EnumerateBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="EnumerateBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupFlags">0x9</Data>
<Data Name="ComponentInfoSummary"><ComponentInfoSummary ComponentInfoArrayPresent="1" TotalComponents="0" SucceededComponents="0" /></Data>
</EventData>
</Event>

Create ISO of Windows Server 2012 R2 Physical Server - NOT VM

Similar Messages

Maybe you are looking for