Create NT Group Failed
Hi There,
On OutlookSoft 4.2 SP6
I have restored a backup on a new server, and all processed fine.
I have changed a user on eAdmin for the user, and try to process the user sheet again, but get the following error.
CreateNTGroups:Failed to create ""WinNT://ERROR/servername/usergroup"" User Group
I get this error for all the groups.
I have deleted the groups, and can see that the database tables gets updated, and if I put the group back the database table gets updated again. But the error still comes up.
This cause the users not to log onto the system.
Any ideas what I can have a look at?
Regards
Henry
Sorin --
I have the same problem in v4.2. Are you suggesting deleting the roles in Analysis Services and then reprocess security? Or do you mean delete the existing groups on the Server for the security groups?
I am processing security using the original creator/install account and I verified that it's in the OLAP Administrators group.
Thanks,
Bob
Similar Messages
-
Hello
I'm setting up a DPM server (2012 R2) at a remote site; everything goes well with no issues until a protection group is created, at which point I get the following error;
Create protection group: Protection Group 1 failed:
Error 360: The operation failed due to a virtual disk service error
Error details: The system cannot find the file specified
Recommended action: Retry the operation.
The environment is as follows;
- Virtual Machine Running Server 2008 R2 Fully updated
- Storage Pool is an iSCSI connection Thick Provisioned 1TB GPT and shows in Disk Management with no issues.
- Have connected to Session 0 (console)
- Error log shows The provider did not receive a Plug and Play service notification for the volume. volume=10 for the VDS Dynamic Provider
Can Anyone Help?
Thanks
.Adam LangdonHi,
Disk defrag is initiated when a volume shrink is attempted. See if there is any problem defragging a volume and correct any problems doing that.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
This posting is provided "AS IS" with no warranties, and confers no rights. -
Error in Creating the Oracle Fail Safe Group during installation on MSCS
Hi All,
I am installing ECC 6 dual stack on MSCS.
I have done steps till CI installation as per installation guide.
I am gettig the following error in the step "Creating the Oracle fail safe group" while changing physical hostname into the virtual databse hostname using configtool in secure store parameter jdbc/pool/<SAPSID>Url as per the installation guide.
"Error occurred while working with configuration(scanning)
MSG:Error while connecting to the database"
I think it is not accepting the virtual hostname.
In our scenario CI is running CI node and DB instance is running on DB node.
I have followed the steps as per the installation guide.
Please let me know how to resolve this issue.
Database - Oracle 10g,OS is Windows server 2008 enterprse edition.
Regards,
Dinakar
Edited by: mutnuru dinakar on Jun 1, 2011 1:39 PM
Edited by: mutnuru dinakar on Jun 1, 2011 1:40 PMHi,
Thanks for your reply.
1) did you stop the CI before making the modifications as stated in the installation guide?
Yes
2) is your database currently running on the same physical cluster node as your CI?
No.Database instance is running on DB node and CI is on CI node.
3) is your database online?
Yes,it is up and running
Please let me know if there is anyway to resolve this issue.
Regards,
Dinakar -
How to create a group of some of the items of a page programatically.
Hi,
I am able to create a group of all Items of a page successfully. But I want to create a group of some of the item of the page.
Below is my code snape:
InterfacePtr<ICommand> groupItemsCmd(CmdUtils::CreateCommand(kGroupCmdBoss));
ASSERT(groupItemsCmd);
if (!groupItemsCmd) {
return;}
InterfacePtr<IGroupCmdData> groupCmdData ( groupItemsCmd, UseDefaultIID());
groupCmdData->Set(itemsOnPageNew);
ErrorCode status = CmdUtils::ProcessCommand(groupItemsCmd);
if (status != kSuccess){ASSERT_FAIL(
"kGroupCmdBoss failed");
break;}
So how I can create UDList of some of the control of the page .
Any help will be appreciable.
Thanks,I have done below code to get tag name but xmlReferenceData object is blank so tagname is blank.
UIDRef pageItemRef=itemsOnPage->GetRef(pageItemIndex);
InterfacePtr<IXMLReferenceData> xmlReferenceData(pageItemRef, DefaultIID());
ASSERT(xmlReferenceData);
if
(!xmlReferenceData) {
break
XMLReference ref = xmlReferenceData->GetReference();
PMString tagname=this->AsString(ref); -
How to create a group of e-mail addresses
Hi,
I need to create a group of recipients (mailing list) using a list of e-mail addresses. I guess I need to use the Address Book, but I could not find the correct way to copy/paste the entire block of addresses. The only way I found was to insert each address, one by one. This drives me crazy because I have to insert some dozens of addresses. Any suggestions? ThanksThis would be an ideal use of Address Book's File > Import...
From Address Book's help:
To import contacts:
Export addresses from another application in a supported format.
Before exporting tab-delimited or CSV files, you may want to note the order of the information fields. If the file doesn’t contain labels, you can refer to your notes to manually identify the fields in a later step.
If the application you’re exporting from supports it, export vCards that include multiple contacts to speed up importing. For example, in Outlook select all of your contacts and choose to forward them as vCards. Send the email message, which includes a vCard attachment for each selected contact, to yourself on your Mac computer. In Mail, save the vCard attachments, and then use Address Book to import them.
Verify the exported .txt or CSV files using a text editor such as TextEdit.
Make sure there are no line breaks within a contact’s information, which can cause the import to fail. Remove any line breaks you find.
Make sure that fields in a .txt or tab-delimited file are separated by a tab, and fields in a CSV file are separated by a comma, instead of by quotation marks or another character. Do not include spaces before or after tabs and commas.
Make sure all addresses have the same number of fields; add empty fields as needed.
In Address Book, choose File > Import, select the file you want to import, change the encoding if necessary, and then click Open.
If you’re importing a text file, review the field labels Address Book will use for the information. You can change field labels, or choose to ignore or not import fields.
If the first card contains headers, review the headers to make sure they are correctly labeled or marked as “Do not import,” and make changes as necessary. Any changes you make to this card are made in all of the cards in the file. To exclude the headers card from being imported, select the “Ignore first card” checkbox.
Use the arrows to browse information in the file to determine if fields need to be relabeled or not imported.
To change a label, click the arrows next to the label and choose a new label from the pop-up menu. If you don’t want to import a field, choose “Do not import.” -
Use Granfeldts Create Object to create dynamic groups
Trying to use Sorens Granfeldts, Create Object WF activity to create dynamic groups.
In a standard function evaluator activity I generate the Filter as [//WorkflowData/Filter]
The "string" I set it to is:
<Filter xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Dialect="http://schemas.microsoft.com/2006/11/XPathFilterDialect" xmlns="http://schemas.xmlsoap.org/ws/2004/09/enumeration">/Person[ObjectID
= /*[ObjectID = '8dfcb5e8-ff01-400c-8ca7-2a0002d2d2d4']/ComputedMember]</Filter>
In the CreateObject activity I then just have [//WorkflowData/Filter],Filter among the initial values.
The creation works if I remove this attribute so the rest of the attributes seems to be working.
The creation fails however end I get the error below in the Forefront Identity Manager event log.
System.NullReferenceException: Object reference not set to an instance of an object.
at Microsoft.ResourceManagement.WFActivities.Resolver.GetDisplayStringFromGuid(Guid id, String[] expansionAttributes)
at Microsoft.ResourceManagement.WFActivities.Resolver.ReplaceGuidWithTemplatedString(Match m)
at System.Text.RegularExpressions.RegexReplacement.Replace(MatchEvaluator evaluator, Regex regex, String input, Int32 count, Int32 startat)
at System.Text.RegularExpressions.Regex.Replace(String input, MatchEvaluator evaluator)
at Microsoft.ResourceManagement.WFActivities.Resolver.GetStringAttributeValue(Object attribute)
at Microsoft.ResourceManagement.WFActivities.Resolver.ResolveEvaluatorWithoutAntiXSS(String match, ResolverOptions resolveOptions)
at Microsoft.ResourceManagement.WFActivities.Resolver.ResolveEvaluatorForWithAntiXSS(String match, ResolverOptions resolveOptions)
at Microsoft.ResourceManagement.WFActivities.Resolver.ReplaceMatches(String input, Boolean useAntiXssEncoding, ResolverOptions resolveOptions)
at Microsoft.ResourceManagement.Workflow.Hosting.ResolverEvaluationServiceImpl.ResolveLookupGrammar(Guid requestId, Guid targetId, Guid actorId, Dictionary`2 workflowDictionary, Boolean encodeForHTML, String expression)
at Microsoft.ResourceManagement.Workflow.Activities.ResolveGrammarActivity.Execute(ActivityExecutionContext executionContext)
at System.Workflow.ComponentModel.ActivityExecutor`1.Execute(T activity, ActivityExecutionContext executionContext)
at System.Workflow.ComponentModel.ActivityExecutor`1.Execute(Activity activity, ActivityExecutionContext executionContext)
at System.Workflow.ComponentModel.ActivityExecutorOperation.Run(IWorkflowCoreRuntime workflowCoreRuntime)
at System.Workflow.Runtime.Scheduler.Run()
Have anyone used this WF activity to create dynamic groups and can tell how to set the Filter?Hey Kent!
I did the same thing, with Søren`s Create Object WF. I did it like this on the filter part:
<Filter xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Dialect="http://schemas.microsoft.com/2006/11/XPathFilterDialect" xmlns="http://schemas.xmlsoap.org/ws/2004/09/enumeration">/Person[(Department = '[//Target/ObjectID]')]</Filter>,Filter
The whole thing looks like this:
(I use Function evaluator to generate a AccountName for groups based on a clean version of DisplayName).
[//Target/DisplayName],DisplayName
SEC_[//WorkFlowData/CleanAccountName],AccountName
[//Target/Manager],Owner
Security,Type
DOMAIN_STRING,Domain
Universal,Scope
[//Target/DisplayName]_SecGroup,Description
[//Target/Manager],DisplayedOwner
None,MembershipAddWorkflow
True,MembershipLocked
[//Target/CleanAccountName],MailNickname
<Filter xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Dialect="http://schemas.microsoft.com/2006/11/XPathFilterDialect" xmlns="http://schemas.xmlsoap.org/ws/2004/09/enumeration">/Person[(Department = '[//Target/ObjectID]')]</Filter>,Filter
Regards, Remi www.iamblogg.com -
Problem creating cache group for a table with data type varchar2(1800 CHAR)
Hi,
I am using TimesTen 7.0 with Oracle 10.2.0.4 server. While creating Cache Group for one of my table I'm getting the following error.
5121: Non-standard type mapping for column TICKET.DESCRIPTION, cache operations are restricted
5168: Restricted cache groups are deprecated
5126: A system managed cache group cannot contain non-standard column type mapping
The command failed.
One of my filed type in oracle table is Varchar2(1800 CHAR). If I change the filed size to <=1000 it (E.g. Varchar2(1000 CHAR)) then the Create Cache command works fine.
MyDatabase Character Set is UTF8.
Is it possible to solve without changing the filed size in the Oracle Table?
Request your help on this.
Thanks,
SunilHi Chris.
The TimesTen server and the Oracle Client is installed on a 32-bit system.
1. ttVersion
TimesTen Release 7.0.5.0.0 (32 bit Linux/x86) (timesten122:17000) 2008-04-04T00:09:04Z
Instance admin: root
Instance home directory: /appl/TimesTen/timesten122
Daemon home directory: /var/TimesTen/timesten122
Access control enabled.
2. Oracle DB details
SQL> select * from v$version;
BANNER
Oracle Database 10g Enterprise Edition Release 10.2.0.3.0 - 64bi
PL/SQL Release 10.2.0.3.0 - Production
CORE 10.2.0.3.0 Production
TNS for Linux: Version 10.2.0.3.0 - Production
NLSRTL Version 10.2.0.3.0 - Production
Oracle Client - Oracle Client 10.2.0.4 running in a 32 bit Linux/x86
3. ODBC Details
Driver=/appl/TimesTen/timesten122/lib/libtten.so
DataStore=/var/TimesTen/data
PermSize=1700
TempSize=244
PassThrough=2
UID=testuser
OracleId=oraclenetservice
OraclePwd=testpwd
DatabaseCharacterSet=UTF8
Thanks,
Sunil -
Rs-ora:resource group failed to start on chosen node; it may end up failing
I have configured two node failover cluster environment using netra a/d 1000 storage. When I try to deploy oracle server application it throws the following error
rs-ora: resource group failed to start on chosen node; it may end up failing over to other node(s)
I created metaset and gave one raw did disk to that metaset.
I created logical hostname resource, ha-storage plus resource. Later I brought the resource group to online using following command
#clrg online emM rg-ora
Later I created oracle cluster resource using following command.
#clrs create -g rg-ora -t SUNW.oracle_server -p ORACLE_HOME=/global/oracle/product/10.2.0/db_1 -p ORACLE_SID=infra -p Alert_log_file=/global/oracle/product/10.2.0/db_1/admin/infra/bdump/alert_infra.log -p Connect_string=sysdba/dbadmin1@infra -p Resource_dependencies=rs-ora-has rs-ora
node1 - Validation failed. ORACLE_HOME /global/oracle/product/10.2.0/db_1 does not exist
node1 - ALERT_LOG_FILE /global/oracle/product/10.2.0/db_1/admin/infra/bdump/alert_infra.log doesn't exist
node1 - PARAMETER_FILE: /global/oracle/product/10.2.0/db_1/dbs/initinfra.ora nor server PARAMETER_FILE: /global/oracle/product/10.2.0/db_1/dbs/spfileinfra.ora exists
node1 - This resource depends on a HAStoragePlus resouce that is not online on this node. Ignoring validation errors.
rs-ora: resource group failed to start on chosen node; it may end up failing over to other node(s)
The status of oracle resource shows as follows.
Resource Name Node Name State Status Message
rs-ora node1 Start failed Faulted
I used solaris 10 update 6 patch level is Generic_137137-09, Oracle version 10.2.0, Sun clusters 3.2 update1. Following are the vfstab and /var/adm/messages of both nodes.
Node1#grep ora /etc/vfstab
/dev/md/oradg/dsk/d300 /dev/md/oradg/rdsk/d300 /global/oracle ufs 5 no logging
Node2#grep ora /etc/vfstab
/dev/md/oradg/dsk/d300 /dev/md/oradg/rdsk/d300 /global/oracle ufs 5 no logging
Node1#more /var/adm/messages
Oct 17 05:19:17 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_prenet_start> for resource <ha-
host-1>, resource group <rg-ora>, node <node1>, timeout <300> seconds
Oct 17 05:19:17 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hafoip/hafoip_prenet_start>:tag=<rg-ora.ha-host-1.10>: Calling security_clnt_connect(..., host=<node1>, sec_typ
e {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:17 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_prenet_start> completed successfully for
resource <ha-host-1>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <300 seconds>
Oct 17 05:19:17 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hastorageplus_prenet_start> for resour
ce <rs-ora-has>, resource group <rg-ora>, node <node1>, timeout <1800> seconds
Oct 17 05:19:17 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hastorageplus/hastorageplus_prenet_start>:tag=<rg-ora.rs-ora-has.10>: Calling security_clnt_connect(..., host=<tes
tlab5>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:18 node1 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<2>:cmd=<null>:tag=<rg-
ora.rs-ora-has.10>: Calling security_clnt_connect(..., host=<node1>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<0>, ...)
Oct 17 05:19:18 node1 Cluster.RGM.rgmd: [ID 316625 daemon.notice] Timeout monitoring on method tag <rg-ora.rs-ora-has.10>
has been suspended.
Oct 17 05:19:20 node1 Cluster.Framework: [ID 801593 daemon.notice] stdout: becoming primary for oradg
Oct 17 05:19:21 node1 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<3>:cmd=<null>:tag=<rg-
ora.rs-ora-has.10>: Calling security_clnt_connect(..., host=<node1>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<0>, ...)
Oct 17 05:19:21 node1 Cluster.RGM.rgmd: [ID 316625 daemon.notice] Timeout monitoring on method tag <rg-ora.rs-ora-has.10>
has been resumed.
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hastorageplus_prenet_start> completed successful
ly for resource <rs-ora-has>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <1800 seconds>
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_start> for resource <ha-host-1>
, resource group <rg-ora>, node <node1>, timeout <500> seconds
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hafoip/hafoip_start>:tag=<rg-ora.ha-host-1.0>: Calling security_clnt_connect(..., host=<node1>, sec_type {0:WEA
K, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_start> completed successfully for resourc
e <ha-host-1>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <500 seconds>
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_monitor_start> for resource <ha
-host-1>, resource group <rg-ora>, node <node1>, timeout <300> seconds
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hastorageplus_start> for resource <rs-
ora-has>, resource group <rg-ora>, node <node1>, timeout <90> seconds
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 510020 daemon.notice] 46 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hafoip/hafoip_monitor_start>:tag=<rg-ora.ha-host-1.7>: Calling security_clnt_connect(..., host=<node1>, sec_typ
e {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hastorageplus/hastorageplus_start>:tag=<rg-ora.rs-ora-has.0>: Calling security_clnt_connect(..., host=<node1>,
sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_monitor_start> completed successfully for
resource <ha-host-1>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <300 seconds>
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hastorageplus_start> completed successfully for
resource <rs-ora-has>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <90 seconds>
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hastorageplus_monitor_start> for resou
rce <rs-ora-has>, resource group <rg-ora>, node <node1>, timeout <90> seconds
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/
lib/rgm/rt/hastorageplus/hastorageplus_monitor_start>:tag=<rg-ora.rs-ora-has.7>: Calling security_clnt_connect(..., host=<tes
tlab5>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:25 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hastorageplus_monitor_start> completed successfu
lly for resource <rs-ora-has>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <90 seconds>
Oct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <bin/oracle_server_validate> for resour
ce <rs-ora>, resource group <rg-ora>, node <node1>, timeout <120> secondsOct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<1>:cmd=</opt/SUNWscor/
oracle_server/bin/oracle_server_validate>:tag=<rg-ora.rs-ora.2>: Calling security_clnt_connect(..., host=<node1>, sec_type
{0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <bin/oracle_server_validate> completed successful
ly for resource <rs-ora>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <120 seconds>
Oct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <bin/oracle_server_init> for resource <
rs-ora>, resource group <rg-ora>, node <node1>, timeout <30> seconds
Oct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</opt/SUNWscor
/oracle_server/bin/oracle_server_init>:tag=<rg-ora.rs-ora.4>: Calling security_clnt_connect(..., host=<node1>, sec_type {0
:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:38 node1 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <bin/oracle_server_init> completed successfully f
or resource <rs-ora>, resource group <rg-ora>, node <node1>, time used: 0% of timeout <30 seconds>
Oct 17 05:19:38 node1 Cluster.CCR: [ID 973933 daemon.notice] resource rs-ora added.
Oct 17 05:19:39 node1 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <bin/oracle_server_start> for resource
<rs-ora>, resource group <rg-ora>, node <node1>, timeout <600> seconds
Oct 17 05:19:39 node1 Cluster.RGM.rgmd: [ID 751138 daemon.notice] 47 fe_rpc_command: cmd_type(enum):<1>:cmd=</opt/SUNWscor
/oracle_server/bin/oracle_server_start>:tag=<rg-ora.rs-ora.0>: Calling security_clnt_connect(..., host=<node1>, sec_type {
0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 17 05:19:48 node1 SC[SUNWscor.oracle_server.start]:rg-ora:rs-ora: [ID 876834 daemon.error] Could not start server
Oct 17 05:19:48 node1 Cluster.RGM.rgmd: [ID 938318 daemon.error] Method <bin/oracle_server_start> failed on resource <rs-o
ra> in resource group <rg-ora> [exit code <1>, time used: 1% of timeout <600 seconds>]
Node2# more /var/adm/messages
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 529407 daemon.notice] resource group rg-ora state on node node2 change to RG_PENDIN
G_OFFLINE
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource rs-ora-has state on node node2 change to R_MON_STOPP
ING
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource ha-host-1 state on node node2 change to R_MON_STOPPI
NG
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_monitor_stop> for resource <ha-host
-1>, resource group <rg-ora>, node <node2>, timeout <300> seconds
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hastorageplus_monitor_stop> for resource <
rs-ora-has>, resource group <rg-ora>, node <node2>, timeout <90> seconds
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 268902 daemon.notice] 45 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/lib/
rgm/rt/hafoip/hafoip_monitor_stop>:tag=<rg-ora.ha-host-1.8>: Calling security_clnt_connect(..., host=<node2>, sec_type {0:WEAK
, 1:STRONG, 2:DES} =<1>, ...)
Oct 14 20:20:04 node2 Cluster.RGM.rgmd: [ID 510020 daemon.notice] 46 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/lib/
rgm/rt/hastorageplus/hastorageplus_monitor_stop>:tag=<rg-ora.rs-ora-has.8>: Calling security_clnt_connect(..., host=<node2>, s
ec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hastorageplus_monitor_stop> completed successfully f
or resource <rs-ora-has>, resource group <rg-ora>, node <node2>, time used: 0% of timeout <90 seconds>
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource rs-ora-has state on node node2 change to R_ONLINE_UN
MON
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource rs-ora-has state on node node2 change to R_STOPPING
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 784560 daemon.notice] resource rs-ora-has status on node node2 change to R_FM_UNKNO
WN
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 922363 daemon.notice] resource rs-ora-has status msg on node node2 change to <Stopp
ing>
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hastorageplus_stop> for resource <rs-ora-h
as>, resource group <rg-ora>, node <node2>, timeout <1800> seconds
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 510020 daemon.notice] 46 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/lib/
rgm/rt/hastorageplus/hastorageplus_stop>:tag=<rg-ora.rs-ora-has.1>: Calling security_clnt_connect(..., host=<node2>, sec_type
{0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_monitor_stop> completed successfully for reso
urce <ha-host-1>, resource group <rg-ora>, node <node2>, time used: 0% of timeout <300 seconds>
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource ha-host-1 state on node node2 change to R_ONLINE_UNM
ON
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hastorageplus_stop> completed successfully for resou
rce <rs-ora-has>, resource group <rg-ora>, node <node2>, time used: 0% of timeout <1800 seconds>
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource rs-ora-has state on node node2 change to R_STOPPED
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource ha-host-1 state on node node2 change to R_STOPPING
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_stop> for resource <ha-host-1>, res
ource group <rg-ora>, node <node2>, timeout <300> seconds
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 784560 daemon.notice] resource ha-host-1 status on node node2 change to R_FM_UNKNOW
N
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 922363 daemon.notice] resource ha-host-1 status msg on node node2 change to <Stoppi
ng>
Oct 14 20:20:05 node2 Cluster.RGM.rgmd: [ID 510020 daemon.notice] 46 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/lib/
rgm/rt/hafoip/hafoip_stop>:tag=<rg-ora.ha-host-1.1>: Calling security_clnt_connect(..., host=<node2>, sec_type {0:WEAK, 1:STRO
NG, 2:DES} =<1>, ...)
Oct 14 20:20:06 node2 ip: [ID 678092 kern.notice] TCP_IOC_ABORT_CONN: local = 192.168.032.244:0, remote = 000.000.000.000:0, s
tart = -2, end = 6
Oct 14 20:20:06 node2 ip: [ID 302654 kern.notice] TCP_IOC_ABORT_CONN: aborted 0 connection
Oct 14 20:20:06 node2 Cluster.RGM.rgmd: [ID 784560 daemon.notice] resource ha-host-1 status on node node2 change to R_FM_OFFLIN
E
Oct 14 20:20:06 node2 Cluster.RGM.rgmd: [ID 922363 daemon.notice] resource ha-host-1 status msg on node node2 change to <Logica
lHostname offline.>
Oct 14 20:20:06 node2 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_stop> completed successfully for resource <ha
-host-1>, resource group <rg-ora>, node <node2>, time used: 0% of timeout <300 seconds>
Oct 14 20:20:06 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource ha-host-1 state on node node2 change to R_OFFLINE
Oct 14 20:20:06 node2 Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource rs-ora-has state on node node2 change to R_POSTNET_S
TOPPING -
Create SCOM Group with dynamic members about 10minutes !
in our SCOM 2012 SP1 (CU3) environment with about 800 Windows Agents.
OperationsDB on a Windows Cluster (2 physical server with 2 processors (six cores). Datawarehouse on separate cluster.
When i create a group with dynamic members, it took about 10min. During this period all the consoles are busy and freezing.
Is that normal ?
Regards
Lehugoon the management server i got follow eventlog error durung this time:
OpsMgr Management Configuration Service failed to execute 'ConfigStoreStatsUpdate' engine work item due to the following exception
Microsoft.EnterpriseManagement.ManagementConfiguration.DataAccessLayer.DataAccessException: Data access operation failed
at Microsoft.EnterpriseManagement.ManagementConfiguration.DataAccessLayer.DataAccessOperation.ExecuteSynchronously(Int32 timeoutSeconds, WaitHandle stopWaitHandle)
at Microsoft.EnterpriseManagement.ManagementConfiguration.SqlConfigurationStore.ConfigurationStore.ExecuteOperationSynchronously(IDataAccessConnectedOperation operation, String operationName)
at Microsoft.EnterpriseManagement.ManagementConfiguration.SqlConfigurationStore.ConfigurationStore.WorkItemCompleted(IConfigServiceEngineWorkItemHandle workItemHandle, IConfigServiceEngineWorkItemResult workItemResult)
at Microsoft.EnterpriseManagement.ManagementConfiguration.Interop.SharedWorkItem.ExecuteWorkItem()
at Microsoft.EnterpriseManagement.ManagementConfiguration.Interop.ConfigServiceEngineWorkItem.Execute()
System.Data.SqlClient.SqlException (0x80131904): Sql execution failed. Error 50000, Level 16, State 1, Procedure WorkItemMarkCompleted, Line 61, Message: Failed to report work item completion. Work item with id 1888748 is not assigned to service instance 'XXXXXX\Default'
at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning()
at System.Data.SqlClient.TdsParser.Run(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj)
at System.Data.SqlClient.SqlCommand.FinishExecuteReader(SqlDataReader ds, RunBehavior runBehavior, String resetOptionsString)
at System.Data.SqlClient.SqlCommand.CompleteAsyncExecuteReader()
at System.Data.SqlClient.SqlCommand.EndExecuteNonQuery(IAsyncResult asyncResult)
at Microsoft.EnterpriseManagement.ManagementConfiguration.DataAccessLayer.NonQuerySqlCommandOperation.SqlCommandCompleted(IAsyncResult asyncResult) -
How Create LDAP Group Inside Active Sync Form?
I have an Active Sync form that is working well to synchronize (and slightly massage) data from an Active Directory source to a Sun Directory Server destination.
I need to synchronize group information from AD to DS. It must automatically create groups during the Active Sync processing. It can't be done externally using another scripting language; it must be done within IdM.
I have the following code...
<Action id='0' application='com.waveset.provision.WorkflowServices'>
<Argument name='op' value='createResourceObject'/>
<Argument name='object'>
<Object>
<Attribute name='resourceId' value='DS'/>
<Attribute name='resourceName' value='DS'/>
<Attribute name='resourceType' value='LDAP'/>
<Attribute name='objectName' value='abcd'/>
<Attribute name='attributes'>
<Object>
<Attribute name='cn' value='abcd'/>
<Attribute name='groupType' value='abcd'/>
</Object>
</Attribute>
<Attribute name='objectType' value='group'/>
<Attribute name='objectId' value='CN=abcd,ou=Groups,dc=blah,dc=com>
</Object>
</Argument>
<Argument name='objectType' value='group'/>
<Argument name='resourceId' value='DS'/>
</Action>However with that code inside the <Field><Expansion>...</Expansion><Field> section the group is not created. I've enabled tracing and as best I can determine the code isn't even executed.
I have created resource schemas for accounts[DS].ldapGroups and accounts[AD].groups and that works well. I can read group memberships from those lists. However I can't simply append to those lists to automatically create groups (which would be nice). That's why I've gone down this path of attempting to create the groups programatically.
I've scoured the groups and the course notes and found nothing relevant here. The examples all refer to creating the groups within an interactive form. I'm trying to do the same within the <Field> section of an Active Sync form.TTSLSAB wrote:
Hi Vladimir,
can you please tell me what should i import in the java class inorder to avoid the below error (session) for the line
Resource resource = (Resource)session.getObject(Type.RESOURCE, resId);
ResourceAdapter ra = ResourceOp.findAdapter(resource, session.getCache());Error, which i am getting is
Exception in thread "main" java.lang.Error: Unresolved compilation problems:
session cannot be resolved
session cannot be resolvedsession is your LighthouseContext handle so depending on how you are implementing the class you quoted, you will either need to pass it in, for example via the invoke tag from your form/workflow, or get your own - don't know how this is done but I'm assuming authenticating to IdM would have to be done.
For all those interested, I have implemented the Java code snippet listed by Vladimir in XPRESS.
idmSessionHandle - is the LighthouseContext for the current session
currentOUDN - is a string representing the AD DN of the OU to be created
<defvar name='resourceAdapterHandle'/>
<set name='resourceAdapterHandle'>
<invoke name='findAdapter' class='com.waveset.provision.ResourceOp'>
<ref>resourceObject</ref>
<invoke name='getCache'>
<ref>idmSessionHandle</ref>
</invoke>
</invoke>
</set>
<defvar name='newOUGenericObject'/>
<set name='newOUGenericObject'>
<new class='com.waveset.object.GenericObject'>
<map>
<s>objectId</s>
<ref>currentOUDN</ref>
<s>objectType</s>
<s>Organizational Unit</s>
</map>
</new>
</set>
<invoke name='createObject'>
<ref>resourceAdapterHandle</ref>
<ref>newOUGenericObject</ref>
<new class='java.util.HashMap'/>
</invoke>
[...]Although the above works well, to create OUs in AD, I have not yet tested its real life application with regards to the initial mass loading of users (from LDAP (auth source) to IdM to AD) and ActiveSyncing. My concerns are two threads attempting to create the OU at roughly the same time, the first succeeds, and second one fails because AD will reply with the fact that the object already exists. The workaround would be to do a recheck of the existence of the OU, after a failure was encountered. This ties into exception handling in general in this approach.
If anyone can contribute exception handling and possibly a create with retries approach, to the above code, I'd appreciate it.
Cheers. -
Create Response groups multiple reponse groups using CSV file
Hi Champs,
We have good amount of response groups has to be created, I try to write the script but failed. Can any one help me to create Response groups through script.
In below script agents should be taken from CSV file.
Import-Module Lync
$serviceId="service:"+(Get-CSService | ?{$_.Applications -like "*RGS*"}).ServiceId;
$ag = New-CsRgsAgentGroup -Name "agent group" -Parent $serviceId;
$ag.Description = "Contain the agents";
$ag.ParticipationPolicy = "Formal"
$ag.AgentAlertTime = "20"
$ag.AgentsByUri.Add("sip:[email protected]")
$ag.AgentsByUri.Add("sip:[email protected]")
$ag.AgentsByUri.Add("sip:[email protected]")
Set-CsRgsAgentGroup $ag
Regards
VijendharYou also need to create queue and workflow. Please check how to create Response Group using Lync Server Management Shell at
http://blogs.technet.com/b/csps/archive/2010/09/15/rgscreateresponsegroup.aspx.
Lisa Zheng
TechNet Community Support -
Create Local Group on Member Servers
Guys,
I have put together below script (thanks to everyone for posting great scripts). I have copied some part of the script from the forum examples.
This script will take Input, create Domain group and add that domain group to the number of member servers listed in the text file.
So far so good, my this script works fine.
Question - I need to add functionality in the script to create new local group on member servers using same variable and Add the Domain group (created using same variable) in the newly created local group on member servers.
I also want to have an output file for the failed hosts.
Appreciate your help.
==============================================
# input
$Name = Read-Host "Write Policy Name"
#Create Domain User Group
NEW-ADGroup -Name ${Name}_UserGroup –groupscope Global -path "ou=Test,DC=Lab,DC=Local" -Description "${Name} Domain users Group"
#Read Servers from the Text File
$Servers = Get-Content c:\temp\${Name}_Servers.txt
#Initialize the Domain Group Object
$DomainGroup = [ADSI]"WinNT://Lab.local/${Name}_usergroup,group"
#Add Domain group to the local Remote Desktop Group on member servers
ForEach ($Server in $Servers) #Loop through each server
#Get Local Group object
$LocalGroup = [ADSI]"WinNT://$Server/Remote Desktop Users,group"
#Assign DomainGroup to LocalGroup
$LocalGroup.Add($DomainGroup.Path)
==============================You don't need scripts to manage local groups.
Group Policy can do this for you.
-- Bill Stewart [Bill_Stewart] -
hello,
when i try creating projects in Project center am posted on with this error.
Your new XXXX workflow has been created successfully, but
failed to publish and will not be listed in the Project Center.For more information on the failure, visit the My Queue Jobs page or contact your administrator.
Any help would be appreciated!!!!!
Thanks regards, Vignesh.hello Rouyre,
Thanks for ur reply
Am using
Microsoft Project Server 2013
15.0.4420.1017
Yes! It is Custom EPT with Custom Workflow(Declarative Workflow) built through VS2012
after associating the Site workflow with EPT i try creating Projects using my Custom EPT since then am posted on with this error.
ULS Error:Log
07/04/2014 10:21:38.03 Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Queue
ad3fy Critical
Standard Information:PSI Entry Point: <unknown> Project User: <unknown> Correlation Id: <unknown> PWA Site URL: SA Name: <unknown> PSError: <unknown> A queue job has failed. This is a general
error logged by the Project Server Queue everytime a job fails - for effective troubleshooting use this error message with other more specific error messages (if any), the Operations guide (which documents more details about queued jobs) and the trace log
(which could provide more detailed context). More information about the failed job follows. GUID of the failed job: 39cd36d6-3603-e411-b33e-00155d00091f. Name of the computer that processed this job: 3eebbc1d-7558-4050-bf5d-d985b23b89f5 (to debug further,
you need to look at the trace log from this computer). Failed job type: ReportWorkflowProj...
2c1ea19c-5849-002d-b89f-50aaf0a752fd
07/04/2014 10:21:38.03* Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Queue
ad3fy Critical
...ectDataSync. Failed sub-job type: ReportWorkflowProjectDataSyncMessage. Failed sub-job ID: 1. Stage where sub-job failed: (this is useful when one sub-job has more than one logical processing stages).
2c1ea19c-5849-002d-b89f-50aaf0a752fd
07/04/2014 10:21:38.03 Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Queue Jobs
ad3fy Medium
Error is: GeneralQueueJobFailed. Details: Queue Attributes: 39cd36d6-3603-e411-b33e-00155d00091f 3eebbc1d-7558-4050-bf5d-d985b23b89f5 ReportWorkflowProjectDataSync ReportWorkflowProjectDataSyncMessage 1 2c1ea19c-5849-002d-b89f-50aaf0a752fd
. Standard Information: , LogLevelManager Warning-ulsID:0x000DD158 has no entities explicitly specified.
2c1ea19c-5849-002d-b89f-50aaf0a752fd
07/04/2014 10:21:38.03 Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Project Server Database
ah91z Medium
Successfully got the connection string (database name=[ProjectWebApp_Practice], id=1f6004ae-5d8a-41d2-81f9-e424a31484aa, type=Consolidated). Requested access level=ReadWrite: Data Source=XXXX;Initial Catalog=ProjectWebApp_Practice;Integrated Security=True;Enlist=False;Pooling=True;Min
Pool Size=0;Max Pool Size=100;Connect Timeout=15
2c1ea19c-5849-002d-b89f-50aaf0a752fd
07/04/2014 10:21:38.04 Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Queue Jobs
ad3fz Medium
PWA:http://XXXX:10000/PWAPactice, ServiceApp:Project Server Service Application, User:PROJECTSERVER\system, PSI: [QUEUE] receiver http://XXXX:10000/PWAPactice: Group 3bcd36d6-3603-e411-b33e-00155d00091f type = ReportWorkflowProjectDataSync aborted at
Message 1, LogLevelManager Warning-ulsID:0x000DD159 has no entities explicitly specified.
2c1ea19c-5849-002d-b89f-50aaf0a752fd
07/04/2014 10:21:38.04 Microsoft.Office.Project.Server (0x1840)
0x06B8 Project Server
Queue Jobs
ad3f2 Medium
PWA:http://XXXX:10000/PWAPactice, ServiceApp:Project Server Service Application, User:PROJECTSERVER\system, PSI: [QUEUE] receiver http://XXXX:10000/PWAPactice: Group 3bcd36d6-3603-e411-b33e-00155d00091f correlation 82705dc5-3603-e411-b33e-00155d00091f
type = ReportWorkflowProjectDataSync failed at Message 1 Errors: GeneralQueueJobFailed, LogLevelManager Warning-ulsID:0x000DD15C has no entities explicitly specified.
2c1ea19c-5849-002d-b89f-50aaf0a752fd
Thanks regards, Vignesh. -
Can not create a group and new users
Good afternoon, colleagues. it is impossible to create a new group and user Pomoz exchange. When trying to select a unit search unit freezes. The logs an error. I do not understand that and what to do. Prompt please. Exchange 2013 and Windows server 2013.
Current user: 'Domain/Company/Emploees/TestUser'
Web service call 'https://exchange.domain:444/ecp/DDI/DDIService.svc/GetList?reqId=905048&schema=OrganizationalUnitPicker&msExchEcpCanary=VVsOZo1K90K_uKYTCFp2jYhxN2V-3dAIUvbEO3KxoMWlqNJV8dPZMZYp4YB7VQ88iXbFzoGR-sI.(https://exchange.domain.ru/ecp/DDI/DDIService.svc/GetList?reqId=905048&schema=OrganizationalUnitPicker&msExchEcpCanary=VVsOZo1K90K_uKYTCFp2jYhxN2V-3dAIUvbEO3KxoMWlqNJV8dPZMZYp4YB7VQ88iXbFzoGR-sI.)' failed with the following error:
System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Collections.Generic.KeyNotFoundException: The given key was not present in the dictionary.
at System.Collections.Generic.Dictionary`2.get_Item(TKey key)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.BuildOUTree(DataTable dataTable)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.GetListPostAction(DataRow inputRow, DataTable dataTable, DataObjectStore store)
--- End of inner exception stack trace ---
at System.RuntimeMethodHandle.InvokeMethod(Object target, Object[] arguments, Signature sig, Boolean constructor)
at System.Reflection.RuntimeMethodInfo.UnsafeInvokeInternal(Object obj, Object[] parameters, Object[] arguments)
at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture)
at Microsoft.Exchange.Management.DDIService.Activity.DoPostRun(DataRow input, DataTable dataTable, DataObjectStore store, Type codeBehind)
at Microsoft.Exchange.Management.DDIService.Workflow.Run(DataRow input, DataTable dataTable, DataObjectStore store, Type codeBehind, UpdateTableDelegate updateTableDelegate)
at Microsoft.Exchange.Management.DDIService.WSListDataHandler.ExecuteCore(Workflow workflow)
at Microsoft.Exchange.Management.DDIService.WSDataHandler.Execute()
at Microsoft.Exchange.Management.DDIService.DDIServiceHelper.GetListCommon(DDIParameters filter, SortOptions sort, Boolean forGetProgress)
at SyncInvokeGetList(Object , Object[] , Object[] )
at System.ServiceModel.Dispatcher.SyncMethodInvoker.Invoke(Object instance, Object[] inputs, Object[]& outputs)
at System.ServiceModel.Dispatcher.DispatchOperationRuntime.InvokeBegin(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage5(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage31(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.MessageRpc.Process(Boolean isOperationContextSet)
at System.RuntimeMethodHandle.InvokeMethod(Object target, Object[] arguments, Signature sig, Boolean constructor)
at System.Reflection.RuntimeMethodInfo.UnsafeInvokeInternal(Object obj, Object[] parameters, Object[] arguments)
at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture)
at Microsoft.Exchange.Management.DDIService.Activity.DoPostRun(DataRow input, DataTable dataTable, DataObjectStore store, Type codeBehind)
at Microsoft.Exchange.Management.DDIService.Workflow.Run(DataRow input, DataTable dataTable, DataObjectStore store, Type codeBehind, UpdateTableDelegate updateTableDelegate)
at Microsoft.Exchange.Management.DDIService.WSListDataHandler.ExecuteCore(Workflow workflow)
at Microsoft.Exchange.Management.DDIService.WSDataHandler.Execute()
at Microsoft.Exchange.Management.DDIService.DDIServiceHelper.GetListCommon(DDIParameters filter, SortOptions sort, Boolean forGetProgress)
at SyncInvokeGetList(Object , Object[] , Object[] )
at System.ServiceModel.Dispatcher.SyncMethodInvoker.Invoke(Object instance, Object[] inputs, Object[]& outputs)
at System.ServiceModel.Dispatcher.DispatchOperationRuntime.InvokeBegin(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage5(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage31(MessageRpc& rpc)
at System.ServiceModel.Dispatcher.MessageRpc.Process(Boolean isOperationContextSet)
System.Collections.Generic.KeyNotFoundException: The given key was not present in the dictionary.
at System.Collections.Generic.Dictionary`2.get_Item(TKey key)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.BuildOUTree(DataTable dataTable)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.GetListPostAction(DataRow inputRow, DataTable dataTable, DataObjectStore store)
at System.Collections.Generic.Dictionary`2.get_Item(TKey key)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.BuildOUTree(DataTable dataTable)
at Microsoft.Exchange.Management.DDIService.OrganizationalUnitPickerService.GetListPostAction(DataRow inputRow, DataTable dataTable, DataObjectStore store)
Help me (Hi,
I would like to verify which group you are creating, distribution group or security group? What's more, please take your time to post the cmdlets you used for my further research.
Here are some helpful articles for your reference.
Manage Distribution Groups
http://technet.microsoft.com/en-us/library/bb124513(v=exchg.150).aspx
Manage Mail-Enabled Security Groups
http://technet.microsoft.com/en-us/library/bb123521(v=exchg.150).aspx
Hope it helps.
Best regards,
Amy
Amy Wang
TechNet Community Support -
Hi, I've used four different Groups when emailing for the past few years, and suddenly they have stopped working. I've tried creating new Groups but that doesn't work either. I haven't changed or done anything different and it is driving me mad......can anyone help, please?!
Thanks for that information!
I'm sure I will be calling AppleCare, but the problem is, they charge for the phone calls don't they? Because I don't have money to be spending to be on the phone with a support service.
In other things, it seemed like the only time my MacBook was working was when I had Snow Leopard without the 10.6.8 update download that was supposed to be done to prepare for OS X Lion.
When I look at the information of my HD it says that I have 10.6.8 but that was the install that it claimed to have failed and caused me to restart resulting in all of the repeated problems.
Also, because my computer is currently down, and I've lost all files how would that effect the use of my iPhone? Because if it doesn't get fixed by the time OS 5 is released, how would I be able to upgrade?!
Maybe you are looking for
-
Table of accounting assignment in sales order
Hi, can anyone show me the table where i can find the accounting assignment in sales-oder position. We have some position which have an entry on accounting assignment in sales order which is an quotation. thanks. Regards, Dieter
-
Some artists not displaying in iTunes browser but load fine under search
I'm having an odd problem with iTunes that has been digging under my skin. Some of my Artists aren't displaying under the Artists pane in the browser. An example of this is my Eazy-E collection. If I serac for Eazy-E all of the songs display and the
-
Need to use a webservice, which expects a Java Forminput class, in Apex
Hi, I'm fairly new to webservices in Apex but have successfully created and used one. We now need to use a webservice that was created for a legacy system and expects a Java Forminput class as its second parameter. msg = webServ.request_Str(sessionId
-
Hi, I tried to run one simple RMI application.. I got the RMI Server running... But While running the client I got the following Exception... java.rmi.MarshalException: error marshalling arguments; nested exception is: java.net.SocketException: Broke
-
The exception error,didn't catch the connection of null user name,help!
help me ! I use the occi and vc to execute a program, when i use a NULL database name or use a NULL user name to connect the oracle,the statement "try...catch(SQLException ex)" didn't catch the error,how i can do? who can tell me how to change the co