Create VTEDS using 9237 + HBM U93 Bridge Sensor

Hi LabView Community!
I'm using LabView 2010 for a short time now, especially trying to set up a monitoring solution for some machines in automotive bodyshop.
My problem is following, i will use TEDS Sensors to make the calibration first (on a own calibration stand) with LabView, to use this in production lines. So i got different sensors, especially for now a HBM U93 5kN Bridge Sensor (Full Bridge 350 Ohms, 0,5mV/V), which got a "Hardware TEDS" in form of a DS2433 EEPROM, but it is build in 1-wire technic, where i got no access with my 9237 Bridge module (works only in 2 wire or Class 2 technic).
In general, i understand how LabView works with TEDS, i can create VTEDS files, read them and use them to set up a measurement-task. For later i'll use this VTEDS files to write them (if any hardware from NI, or i use other) on the sensors EEPROM.
But to calibrate the sensors, i don't understand, how i get the measured electrical values (AI+ / AI-) out of my 9237. I can use and i use the MAX explorer to calibrate the "null" value of the sensor, but where can i access the electrical value at this point (or the divided Value of , to write it in my TEDS file for my 0 N value? The same problem is to calibrate it with a physical, known force (with a reference sensor), i can't find the place where i can get the electrical value out of the 9237. Shunt calibration doesn't work anyway, i tried here all things that were described in forums or somewhere else from NI. I tried always the "calibration table", but until now i didn't correctly understand how this one is to use in the right way.
It would be very helpful for me, if i'd know, where the electrical or representative values are accessible to calibrate the sensors!
thank you very much!
regards, Dennis

Hi,
This could maybe help you:
Continuous Wheatstone Bridge Measurements with Calibration - NI 9237
https://decibel.ni.com/content/docs/DOC-12258
Regards
Florian Abry
Application Engineer Group Leader
NI Germany

Similar Messages

HT201269 My iphone contacts are not updating to Icloud, I can create a contact in Icloud and it will update to my phone but I cannot create a contact on my phone to have it update in the cloud, I am using Itunes as the bridge

My iphone contacts are not updating to Icloud or Outlook, I can create a contact in Icloud/Outlook and it will update to my Iphone but I cannot create a contact on my Iphone to have it update in the Cloud/Outlook, I am using Itunes as the bridge. I originally installed the Icloud manager to sync my contacts to Cloud/Outlook, but I did not like the functionality, when I uninstalled the Cloud manager and and installed Itunes I noticed that the none of my contacts in the phone updated to Outlook.
Thanks in advance.

Hi Cyclops12,
Welcome to the Support Communities!
The article below may be able to help you with this.
iCloud: Troubleshooting iCloud Contacts
http://support.apple.com/kb/ts3998
Cheers,
- Judy

How can I create my own shortcuts in Adobe Bridge?

Hey everyone,
This is my first post here on the Adobe forum and I've been searching for my question without an adequate answer, therefor I turn to you. My question is if it's possible to create my own shortcuts in Adobe Bridge. I would like to get a shortcut for the label "To do" (purple) since it's the one I use the most. Thanks in advance, and happy new year!
/Konrad

iOS Dev Center - Apple Developer
iOS Developer Program - Apple Developer

Creating portals using webcenter/jdeveloper deployment issue

Can we deploy portals created using webcenter/jdeveloper to earlier non -jdeveloper oracle portals or rather the portal pages? Basically I am asking this because we are using new technology for us being webcenter and trying to make it backwards compatible with the oracle portal pages for certain projects rather then recoding.
Edited by: user609513 on Dec 4, 2008 4:42 PM

Hi,
Portal 10.1.4 has WSRP and JSR 168 Standards compatibility, this means that you WebCenter portlets (which are JSR portlets) can be deployed to Portal 10.1.4 pages.
The page definitions and security will have to be re-created, but all your logic(portlets) will be reused.
Another alternative is to use the JSF Portlet Bridge feature of Oracle WebCenter to wrap your whole WC application into a portlet and deploy it into portal, check this document:
http://www.oracle.com/technology/products/webcenter/pdf/owcs_10132_cm_jsf_bridge.pdf
Regards,
Juan

Error while creating stock using tcode: MB1C

Error while creating stock using tcode: MB1C
The Error is: Check table T004F:entry G006 does not exist

Hi ,
Please check the FSV (field status variant) for your company code in OBY6 .
then go to transaction code OB14 --> enter the FSV --> Check if field status group G006(Material account) is maintained there or not.
if not please maintain it.
Thanks & Regards
Anshu

Logical error in creating tables using db link in solaris

Hi,
While creating table using the syntax create table newtab...as select * from tab@dblink .. I am facing a problem. The newtab table created is having a structure different (from datalength point of view of varchar2 and char datatypes) from the source. The data length is getting tripled i.e. if a column a is varchar2(20) in tab then it is becoming --- a varchar2(60) in newtab. This is happening in solaris environment when the two databases are in 2 different servers. Please let me know if there are any patches to resolve the problem.
Thanks
Arnab

ORA-02019: connection description for remote database not foundHave you used this database link successfully for some other queries?
The error posted seems to indicate that the DB Link is not functional at all. Has it worked for any other type of DML operation or is this the first time you ever tried to use the link?

How to save report in PersonalCategory after creating it using java panel?

Hi,
Anybody knows How to save report in PersonalCategory after creating it using java panel?
I dont want to save it in public folder. I want to save report (webi) in user's personal category.
can anybody send me source code?
It will help me a lot.
Thanks in advance
Amol Mali

Hi teda,
i'm assuming that you have seen my post that i did successfuly save report in user's personal category.
Actually the report is created in webi java panel using RE SDK and is saved in Report Sample Folder then i'm saving it in user's personal category by following code
string query = "Select SI_PERSONAL_CATEGORIES From CI_INFOOBJECTS Where "
                     + "SI_INSTANCE=0 And SI_ID=" + reportID;
                InfoObjects infoObjects = infoStore.Query(query);
                InfoObject infoObject = infoObjects[1];
                Webi wreport = (Webi)infoObject;
                ObjectRelativeIDs personalIDs = wreport.PersonalCategories;
            /personalIDs.Add(Convert.ToInt32(categoryID));
               infoStore.Commit(infoObjects);
But the report is presents in the Folder also and in user's personal category also.
I dont want the report to be in the folder (Report Sample) if i saved it in user's personal category.
How can i do that?
any idea.
Please help me.
Thanks in advance
Amol Mali
Edited by: amol mali on Jan 9, 2009 7:55 PM

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?
I have tried back ups and restoring, resetting, and even updating the pages app. And nothing has worked.

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?
I have tried back ups and restoring, resetting, and even updating the pages app. And nothing has worked.

Why Dynamic Parameter is not working, when i create report using stored procedure ?

Post Author: Shashi Kant
CA Forum: General
Hi all
Why Dynamic Parameter is not working, when i create report XI using stored procedure ?
Only i shaw those parameters which i used in my stored procedure, the parameter which i create dynamic using stored procedure
is not shown to me when i referesh the report for viewing the results.
I have used the same procedure which i mention below but can not seen the last screen which is shown in this .
============================================================================================
1. Select View > Field Explorer2. Right-click on Parameter Fields and select New from the right-click menu.3. Enter u201CCustomer Nameu201D as the name for your parameter4. Under u201CList of Valuesu201D select u201CDynamicu201D5. Under the Value column, click where is says u201Cclick here to add itemu201D and select Customer Name from the drop-down list. The dialog shown now look like the one shown below in Figure 1. Click OK to return to your report design.
Dynamic Parameter Setup6. Next, select Report > Select Expert, select the Customer Name field and click OK.7. Using the drop-down list beside select u201CIs Equal Tou201D and using the drop-down list, select your parameter field (it should be the first field). 8. Click OK to return to your report design and see the parameter dialog.The parameter dialog will appear and show you a dynamic list of values that is updated each time your run your report. It couldnu2019t be easier! In our next tutorial, we will be looking at how to use this feature to create cascading parameter fields, where the values are filtered by the preceding selection.
Dynamic Parameters in Action
My question is that whether dynamic parameter is working with storedprocedure or not.
When i added one table and try to fetch records using dyanmic prameters. after that i am not be able to find the dynamic parameter option when i referesh my report.
One more thing when i try the static parameter for my report, the option i see when i referesh the screen.
Please reply soon , it's urgent
Regards
shashi kant

Hi Kishore,
I have tested the issue step by step by following you description, while the first issue works well in my local environment. Based on my research, this can be caused by the lookup expression or it indeed return Male value based on the logic. If you use the
expression below, it will indeed only return the Male record. So please try to double-check the record in the two datasets and the expression in your environment:
=lookup(first(Fields!ProgramID.Value,"DataSet1"),Fields!ProgramID.Value,Fields!Gender.Value,"DataSet2")
As to the second issue, please try to use the following expression:
=Count(Lookup(fields!ProgramID.value,fields!ProgramID.value,fields!Gender.value,"DataSet2"))
Besides, if this issue still exist, in order to trouble shoot this issue more efficiently, could you please post both the .rdl file with all the size properties to us by the following E-mail address? It is benefit for us to do further analysis.
E-mail: [email protected]
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

Creating Report using EPM Functions with Dynamic Filters

Hi All,
I am new to BPC, In BPC 7.5 i seen like we can generate EPM report using EVDRE function very quickly and easy too. Is the same feature is existing in BPC 10.0 ? if no how can we create EPM reports using EPM Functions with Dynamic Filters on the Members of the dimension like in BPC 7.5.
And i searched in SDN, there is no suitable blogs or documents which are related to generation of Reports using EPM Functions. All are described just in simple syntax way. It is not going to be understand for the beginners.
Would you please specify in detail step by step.
Thanks in Advance.
Siva Nagaraju

Siva,
These functions are not used to create reports per se but rather assist in building reports. For ex, you want to make use of certain property to derive any of the dimension members in one of your axes, you will use EPMMemberProperty. Similary, if you want to override members in any axis, you will make use of EPMDimensionOverride.
Also, EvDRE is not replacement of EPM functions. Rather, you simply create reports using report editor (drag and drop) and then make use of EPM functions to build your report. Forget EvDRE for now.
You can protect your report to not allow users to have that Edit Report enabled for them.
As Vadim rightly pointed out, start building some reports and then ask specific questions.
Hope it clears your doubts.

How to create invoice using bapi base on delivery number with example

hi,
Pl give me one example to create invoice using bapi base on delivery number (PGI).

Use this code
* Pass the delivery no to the FM to create the invoice
      wa_vbsk-smart = u2018Fu2019.
        wa_komfk-vbeln = nast-objky. u201CuF0DF-----delivery number
        APPEND wa_komfk TO it_komfk.
        CLEAR wa_komfk.
*    To fill the message structure
*        l_wa_error-vbeln_vl = nast-objky. " Delivery No.
*        l_wa_error-fkart = wa_ztab-bil_doc_type." Billing Doc type
        CALL FUNCTION 'RV_INVOICE_CREATE'
                EXPORTING
*                 delivery_date             = 0
                 invoice_date              = v_date u201C<- date
*                 invoice_type              = '    '
*                 pricing_date              = 0
                 vbsk_i                    = wa_vbsk
                 with_posting              = u2018Du2019
*                 select_date               = 0
                 i_no_vblog                = ' '
                 i_analyze_mode            = ' '
                 id_utasy                  = ' '
                 id_utswl                  = ' '
                 id_utsnl                  = ' '
                 id_no_enqueue             = ' '
                 id_new_cancellation       = ' '
**             IMPORTING
*               VBSK_E                    =
*               OD_BAD_DATA               =
*               DET_REBATE                =
                TABLES
                  xkomfk                    = it_komfk
                  xkomv                     = it_komv
                  xthead                    = it_thead
                  xvbfs                     = it_vbfs
                  xvbpa                     = it_vbpa
                  xvbrk                     = it_xvbrk
                  xvbrp                     = it_vbrp
                  xvbss                     = it_vbss
*               XKOMFKGN                  =
*               XKOMFKKO                  =

Error while creating Resource using GDS

Hi
Iam trying to create Resource using GDS and it is throwing me error
clresource: (C189917) VALIDATE on resource egateq00-haegate_reg-res, resource group egateq00-rg, exited with non-zero exit status.
clresource: (C720144) Validation of resource egateq00-haegate_reg-res in resource group egateq00-rg on node uhegateq02 failed.
clresource: (C891200) Failed to create resource "egateq00-haegate_reg-res".
This is the command I executed
rclresource create -g egateq00-rg -t SUNW.gds
-p Scalable=false -p Start_timeout=120 -p Stop_timeout=120 -p Probe_timeout=30
-p Port_list="23001/tcp" -p Start_command="/egateq00/scripts/reg_START.sh" -p Stop_command="/egateq00/scripts/reg_STOP.sh"
-p Probe_command="/egateq00/scripts/reg_PROBE.sh" -p Child_mon_level=1 -p Network_resources_used=egateq00-lh-res -p Failover_enabled=FALSE
-p Stop_signal=15 egateq00-haegate_reg-res
The log under /var/cluster/logs/DS says following
07/01/2008 17:56:43 uhegateq02 START-INFO> scha_resource_open failed [14]. Keeping the old Log_level value
07/01/2008 17:56:43 uhegateq02 START-ERROR> Cannot access the start command </egateq00/scripts/reg_START.sh> : <No such file or directory>
07/01/2008 18:13:23 uhegateq02 START-INFO> scha_resource_open failed [14]. Keeping the old Log_level value
07/01/2008 18:13:23 uhegateq02 START-ERROR> Cannot access the start command </egateq00/scripts/reg_START.sh> : <No such file or directory>
However, I can open these scripts and run it from anywhere. I also tested these scripts and they all work fine. They are all set to chmod 777 , so everyone should have execute permission
Iam not returning any return value from these Start and Stop script , is that the why it is failing
thanks

Hi
I disabled the PMF as described on the http://blogs.sun.com/TF/entry/disabling_pmf_action_script_with. This is what I did
1>Added following line in the top of my Start script
while getopts 'R:G:' opt
do
case "${opt}" in
R) RESOURCE=${OPTARG};;
G) RESOURCEGROUP=${OPTARG};;
esac
done
sleep 60 &
/usr/cluster/bin/pmfadm -s ${RESOURCEGROUP},${RESOURCE},0.svc
2>While creating the resource , I used property for Start_command="/egateq00/scripts/reg_START.sh -R %RS_NAME -G %RG_NAME"
Now , after doing this , My RG is not getting lost. Also , in the message file I do not see the errors of "Start script failed to stay UP"
However, My Application is not started either.
This is what the message file says
Jul 3 16:43:32 uhegateq01 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <gds_validate> completed successfully for resource <egateq00-haegat
e-reg-res>, resource group <egateq00-rg>, node <uhegateq01>, time used: 0% of timeout <300 seconds>
Jul 3 16:43:32 uhegateq01 Cluster.CCR: [ID 973933 daemon.notice] resource egateq00-haegate-reg-res added.
Jul 3 16:43:32 uhegateq01 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <gds_svc_start> for resource <egateq00-haegate-reg-res>,
resource group <egateq00-rg>, node <uhegateq01>, timeout <120> seconds
Jul 3 16:43:32 uhegateq01 Cluster.RGM.rgmd: [ID 252072 daemon.notice] 50 fe_rpc_command: cmd_type(enum):<1>:cmd=</opt/SUNWscgds/bin/gds_svc_star
t>:tag=<egateq00-rg.egateq00-haegate-reg-res.0>: Calling security_clnt_connect(..., host=<uhegateq01>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, .
Jul 3 16:43:35 uhegateq01 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <gds_svc_start> completed successfully for resource <egateq00-haega
te-reg-res>, resource group <egateq00-rg>, node <uhegateq01>, time used: 2% of timeout <120 seconds>
Jul 3 16:43:35 uhegateq01 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <gds_monitor_start> for resource <egateq00-haegate-reg-re
s>, resource group <egateq00-rg>, node <uhegateq01>, timeout <300> seconds
Jul 3 16:43:35 uhegateq01 Cluster.RGM.rgmd: [ID 252072 daemon.notice] 50 fe_rpc_command: cmd_type(enum):<1>:cmd=</opt/SUNWscgds/bin/gds_monitor_
start>:tag=<egateq00-rg.egateq00-haegate-reg-res.7>: Calling security_clnt_connect(..., host=<uhegateq01>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1
, ...)Jul 3 16:43:35 uhegateq01 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <gds_monitor_start> completed successfully for resource <egateq00-h
aegate-reg-res>, resource group <egateq00-rg>, node <uhegateq01>, time used: 0% of timeout <300 seconds>
4>Also , in the /var/cluster/logs/DS , I see the Start script started succesfully
07/03/2008 16:43:32 uhegateq01 START-INFO> Start succeeded. [egateq00/scripts/reg_START.sh -R egateq00-haegate-reg-res -G egateq00-rg]
5>Also , in the /var/cluster/logs/DS , I see the Probe script returning 0 , but this is wierd because it should return Non zero number. When I run the Probe script from the command line , it is returning me non zero value when the application is down
07/03/2008 16:43:35 uhegateq01 PROBE-INFO> The GDS monitor (gds_probe) has been started
07/03/2008 16:44:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:44:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:45:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:45:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:46:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:46:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:47:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:47:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:48:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:48:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:49:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:49:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:50:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:50:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:51:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:51:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:52:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:52:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:53:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:53:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:54:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:54:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:55:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:55:35 uhegateq01 PROBE-INFO> The probe result is 0
07/03/2008 16:56:35 uhegateq01 PROBE-INFO> Probe has been executed with exit code 0 [egateq00/scripts/reg_PROBE.sh]
07/03/2008 16:56:35 uhegateq01 PROBE-INFO> The probe result is 0

Error while creating Routing using LSMW

Hi Guys ,
I am trying to create LSMW using Direct Input Method .
My structures are ::
RC271_DS Work center structure for direct input (for datasets)
RC27M_DS Material master view DIRECT INPUT routing for datasets
PLKO_DI_DS Header structure for direct input (for datasets)
PLPO_DI_DS Routing/item structure for direct input (for datasets.
I getting correct data from multiple flat files .
It's converting the data also .
But while executing start direct input method i am getting the followig error ....
You cannot edit the task list object with activity type
Please let me know problem guys .
Regards,
Raj

Hi Naveen,
It means you have to assign the task list type to material type ZPRD. Then it will carry its job:
The path is:
Go To-> SPRO-> IMG Activity-> Production-> Basic Data-> Routing-> General Data---> Define Material Type Assignments. T-Code: OP50
I hope it will work.
Regards,
Madhu.G

Error while creating BOM using BAPI 'BAPI_BOM_UPLOAD_SAVE'

Hi All,
We are getting an error as 'Data is incomplete' while trying to create BoM using the bapi 'BAPI_BOM_UPLOAD_SAVE', if the item contains Item category as 'T'. But for other item category like 'L' or 'N', the bapi is sucessfull.
The values that we pass to fill the item category 'T' are operation, item_cat, bom_itm_no, COMPON_QTY, FIXED_QTY as 'X', UNMEAS as 'ST', ITEM_TEXT1 and ITEM_TEXT2.
Anyone who has faced same problem or has a solution to the problem, kindly provide a solution.
Regards,
Vijay

The error you receive is because of different config for different Item Categories. Find out from the functional team what fields have they kept mandatory for the item category 'T'. You may not be passing one of those fields in the BAPI.
Try creating a BOM manually for item category 'T' and you may figure our which field you are missing.

Error while creating AW using DBMS_LOB with XML..

Hi All,
I am trying to create AW using DBMS_LOB package with XML,
while creating AW,i am facing the following error.find the code also below :
declare
xml_awcreate_clob clob;
xml_awcreate_st varchar2(4000);
begin
DBMS_LOB.CREATETEMPORARY(xml_awcreate_clob,TRUE);
dbms_lob.open(xml_awcreate_clob, DBMS_LOB.LOB_READWRITE);
dbms_lob.writeappend(xml_awcreate_clob, 48, '<?xml version = ''1.0'' encoding = ''UTF-8'' ?>');
dbms_lob.writeappend(xml_awcreate_clob, 43, '');
dbms_lob.writeappend(xml_awcreate_clob, 63, '<AWXML version = ''1.0'' timestamp = ''Mon Feb 11 13:29:11 2002'' >');
dbms_lob.writeappend(xml_awcreate_clob, 15, '<AWXML.content>');
dbms_lob.writeappend(xml_awcreate_clob, 25, ' <Create Id="Action41">');
dbms_lob.writeappend(xml_awcreate_clob, 19, ' <ActiveObject >');
dbms_lob.writeappend(xml_awcreate_clob, 163, ' <AW Name="NEW_XML_AW" LongName="NEW_XML_AW" ShortName="NEW_XML_AW" PluralName="NEW_XML_AW" Id="NEW_XML.AW"/>');
dbms_lob.writeappend(xml_awcreate_clob, 19, ' </ActiveObject>');
dbms_lob.writeappend(xml_awcreate_clob, 11, ' </Create>');
dbms_lob.writeappend(xml_awcreate_clob, 16, '</AWXML.content>');
dbms_lob.writeappend(xml_awcreate_clob, 8, '</AWXML>');
dbms_lob.close(xml_awcreate_clob);
xml_awcreate_st := sys.interactionExecute(xml_awcreate_clob);
end;
ORA-21560: argument 2 is null, invalid, or out of range
ORA-06512: at "SYS.DBMS_LOB", line 833
ORA-06512: at line 12
Any idea or thought on this would be appreciable.
Thanks in advance.
Anwar

Did you change any of the text in the lob write statements ?
I believe you get this error if you increase the number of characters without increasing the 1st argument which looks as though it represents the number of characters

Create VTEDS using 9237 + HBM U93 Bridge Sensor

Similar Messages

Maybe you are looking for