Creating a Separate Wireless Network With no Ethernet

Hello-
I am attempting to set-up my Airport Express with my receiver and speakers in order to play music wirelessly. I have successfully done so when I choose "Join an Existing Wireless network", but I have noticed that this bogs down my wi-fi network speeds tremendously.
So, instead, I attempted setting-up the Airport Express as its own wireless network in order to bypass my DSL-based, wi-fi network completely. But, when doing so, I am being forced to connect to my DSL via ethernet.
Is there a way arpund this? Or, is there a way to stream music via the airport express in a way that won't interfere with my DSL wi-fi network (or affect its speed)?
Thanks in advance!

The AirPort Express Base Station (AX) does NOT require an Internet connection in order for it to provide a standalone wireless network for streaming.
The AX would not get a Public IP address, but it would have a Private IP address of 10.0.1.1 ... and it would be providing wireless clients connected to it with Private IP addresses in the 10.0.1.2 - 10.0.1.200 range.
I just verified that this works. Please double-check your settings to see if you may have missed something.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Create a wireless network
Wireless Network Name: <enter a desired Network Name or SSID>
Radio Mode: <leave the default or select a desired radio mode>
Channel: Automatic
Wireless Security: <select the desired wireless security type>
Internet > Internet Connection
Connect Using: Ethernet
Connection Sharing: Distribute a range of IP addresses
Internet > TCP/IP
Configure IPv4: Manually
IP Address: 10.0.1.1
Subnet Mask: 255.255.255.0
Router Address: 10.0.1.1
DNS Server(s): <leave blank>
Domain Name: <leave blank>
Internet > DHCP
DHCP Beginning Address: <leave default or change to a desired starting address>
DHCP Ending Address: <leave default or change to a desired ending address>
Music
Enable AirTunes (checked>
iTunes Speaker Name: <leave default or enter a desired speaker name>
Advanced > Logging & Statistics
Allow SNMP (unchecked)
Your AX will still report at least three errors: 1) Configuration of WAN, 2) SNMP over WAN, and 3) Double NAT. These can all be safely ignored to stop the AX's status light from flashing amber in this configuration.

Similar Messages

How to use Airport Extreme to create a second wireless network with different IP addresses behind an existing modem/router?

Hi,
I have an existing modem/router from my ISP that does DHCP and NAT with base IP 192.168.1.1 distributed in the wireless network. I use this wireless network for our private devices. I could turn off the DHCP server in this first router, but there isn't a separate setting to turn off NAT.
I want to connect my Airport Extreme (4th gen) to this existing router to create a separate wireless network for visiting guests, where IP addresses of 10.0.0.0 etc. are used. So I do not want to use the Airport Extreme in bridge mode, as I would like to keep the devices on the first network 'invisible' for those on the second network. (P.S. when connected in bridge mode, the Airport works well and can distribute a network with a different name from the first. It's just that I would feel more comfortable about our privacy if the Airport were to distribute a different IP range. False security, maybe?)
I've tried doing this by 'Sharing a public IP address' in Airport Utility's Internet tab, leaving TCP/IP's setting to 'via DHCP', setting DHCP addresses to start with 10.0.0.2 up to 200 with all else blank, and not using a standard host nor NAT-PMP in the NAT tab.
When I do this the Airport complains of a 'double NAT issue'. Internet connectivity seems to be OK, but when switching between the two networks on my Mac I get complaints about my IP address being in use by another device intermittently.
Can anyone help in how to get the 'double NAT issue' resolved?
Thanks!

So if someone is connected to the modem/router network they will be able to see the HD I will have put in to the AirPort Extreme?
As I said above.....since the modem/router and AirPort are bridged, devices on the modem/router wireless will be able to "see" devices on the AirPort wireless, and vice versa.....
If they can see the HD connected to the AirPort Extreme, will they be able to access it
Yes, unless you plan to password protect the drive connected to the AirPort Extreme.
or will they still need the password needed to get onto the AirPort Extreme network?
The modem/router and AirPort Extreme are bridged. They are on the same network. All devices are on the same network when the modem/router and AirPort are bridged. Not sure how else that I can say this.
Also, because it is bridged, I shouldn't have any problems accessing the HD I will have connected to the AirPort Extreme from an external location?
Accessing devices from a remote location is never easy....and a topic for a different post/discussion. If you have a "static" Internet IP address from your provider, and have all the details on how to forward ports on your modem/router, you are off to a good start.
Apparently there is some addressing issues because devices can be seen as "Double IP" because the modem/router would have allocated IP's as well as the AirPort allocating IP's thus making connections slower until resolved
When you "bridge", all IP addresses are issued by one device. There will be no conflicts on the network, since they are bridged.
Once again, in very simple terms, you have two doors (access points) that open into the same room (network). One "door" is the modem/router and the other "door" is the AirPort Extreme. They are on the same network....("room") because they are bridged.

Creating a seamless wireless network with 2 AExpress units

I have 2 Airport Express units in different parts of my house. I have struggled for YEARS trying to get them to create one seamless wireless network with the same name that I could float between. I have never been able to get that to work. anyone?
I know that some of the problems MAY have to do with the non-apple router settings, but I just have never gotten a clear response form anyone about weather it is doable, and/or worth doing. I would settle for 2 seperate wireless networks that didn't compete with each other and/or constantly need re-booting to stay active. I am generally the most tech savvy person I know and am consulted on IT by friends and colleageus regularly, but I just cannot figure this one out..
I am totally capable of setting this up, both in the router and the AE units, if someone can just tell me that;
1) yes it is possible and it will work, and
2) just set it up like this...

Thanks for the clarification. Check your AirPort Express devices one at a time, but other than different device names to avoid confusion.....AirPort Express 1, AirPort Express 2....for example, the settings should look this:
Open AirPort Utility , select one AirPort Express, click Manual Setup
Click the Wireless tab below th row of icons
Wireless Mode = Create a wireless network
Wireless Network Name = Your choice
No check mark needed next to "Allow this network to be extended"
Radio Mode = 802.11n (802.11 b/g compatible) a good choice, but you can choose other combinations by holding down the option key on your Mac while you click on the selection box
Channel = Automatic
Wireless Security = WPA2 Personal an excellent choice if all of your devices are compatible with this setting
Wireless Password = Your wireless password
Confirm Password
Click the Internet icon
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings
Configure AirPort Express 2 exactly the same way and Update to save settings
Then, power down the entire network.....all devices....order is not important
Wait a moment, then start the modem/router first and let it run 2-3 minutes by itself
Start each AirPort Express the same way
Start each other network device one at a time about a minute apart
Check for proper network operation
IF....you did not have your AirPort Express devices in Bridge Mode before.....that is the reason why you are having issues now and also is the reason why the "roaming" network was not working.....assuming that there was a reasonable overlap in wireless coverage between the 2 Express devices, of course.
If you want to try the "roaming" setup again, assign the exact same wireless network name, security and password to both Express devices and confirm again that both are setup in Bridge Mode as the very last step before you click the Update button in AirPort Utility.
Power down the entire network and start up in sequence as well as in the example above.

Can I create two separate wireless networks?

At this time I am using my own wireless router Netgear WNDR3700. Works well.
I would like to add second router (Dlink DIR825) but not as repeater or access point.
Can I connect both directly to to Cat 6 coming from OMT thru the Ethernet switch creating 2 separate networks?
With its own SSID's and use the second network to connect in the garage where my signal is week from the netgear. Is it possible?
Solved!
Go to Solution.

PGJK wrote:
Somebody on this forum a few weeks back said this could be done.
If it can it would be a violation of your TOS as for it to work you would havve to be acquiring two dhcp addresses from the VZ network.
Tech support told me that installation of router downstram of ActionTec router does not violate TOS. It merely remove Verizon support & ActionTec's router from the loop for Internet services, and of course its no longer Verizon's problem should any problems arise on the installed router or it's network (CAUTION: this is done at your own risk). In theory that could be hardwired or wireless. Those services which retain connection from the ONT to Verizon's ActionTec router will similarly retain viable Verizon responsibility and FIOs support.
I don't think he's connecting his router to a VZ router.
I think he's suggesting connecting a switch directly to the ONT and then 2 routers to the switch. That will give him 2 VZ DHCP addresses

Can't create a working wireless network (with AEBS N station)

I have a new Airport Extreme Base Station (802.11n), firmware 7.2.1 and a PowerMac G4 running Leopard, with the built-in Ethernet port dead, fried by a storm.
I installed a PCI Gigabit network card which works great. I have a static IP, and no more DSL modem. I am connected directly (via fiber) to my ISP. I purchased the AEBS N to create a wireless network for my iPhone and my laptop(soon to come). But after "successfully" setting up the base station with my IP settings I cannot connect to Internet. I believe that the base station or the actual firmware is not "smart" enough to "look" to anything else but the built-in Ethernet port. It simply tells me that there is nothing connected to the WAN port (even-though I was able to upload all the settings to the AEBS)
AEBS Settings: Create a wireless network,Share an IP address, router mode and Mac connected via DHCP. The wireless network is visible by clients , but they also can't connect to the Internet.
What is wrong? Should I set AEBS in BRIDGE mode? Can someone, please help?
Thank you in advance!

Duane, Thanks for your reply!
I used to be connected via a DSL modem, but now, my ISP removed the modem saying is no longer needed and I am connected only to a wire.(so that means I am part of a LAN I guess) They say is fiber optic up to my block of flats. They have a box on the staircase from where multiple wires goes to apartments! I believe lies a switch in there...!All I know for sure is that I have a static IP and all these numbers I uploaded to the base station! All I have is the amber flashing light and the "nothing connected to the WAN port" msg.
I tried to set the device in bridge mode, but no luck! No Internet!When I connect directly to my mac everything is fine!
They said no problem if I want to put a wirless router in the house!Should I ask them for any specific settings?
Repeat: The Ethernet port I use is from a PCI card. The built in Ethernet is dead! Can this be a reason?
Please let me know if you need other details!

HT2421 If I attach a hard drive to the USB port, can I access it from the wired network, while simultaneously creating a separate wifi network with NO access to the hard drive?

I already have a wireless network (call it Network A) with connectivity to various wired and wireless devices. I have a USB hard drive that I directly attach to my MacBook Air. I use it for Time Machine backups and general storage. I would like to move this drive to an AirPort Extreme. I would like to continue to be able to reach it via Network A, but also use the AirPort to create a guest Network (Network B). I don't want the guest network to access the hard drive.
Now, I know I can plug a hub into the USB port and put (I hear up to 3) hard drives on it. Can I determine which ones are accessable by Network A, and by Network B?
Bonzo...

Several things to consider.
You cannot create a wireless network for guests if the AE is bridged. It has to be the main router in the network.
You cannot use the existing TM backups on the USB drive.. if you plug into a network it will need to be wiped.. and only AC model can produce reliable TM backups.. the earlier models are not reliable for TM backups.
See http://pondini.org/TM/Airport.html
These two factors alone may be enough to make you reconsider.
If you can create a guest network.. and you can overcome the limitations of airdisks.. then any person on the guest network should not be able to access the disk drive.. but if you wish to go ahead Bob Timmons might be able to confirm it.. I stay away from USB drives on routers.. I do not and will not use a router as a NAS.. it is underpowered and simply unsuitable long term.. a cheap single disk NAS is many times faster.. more reliable.. and has a marvellous thing called backup.. no USB disk or even internal disk in a TC can back itself up. .nor can TM backup network drives.. so any data you store on a USB drive is going to be gone one day.. unless you go to great lengths to back it up .. to where.. another USB drive plugged into another router somewhere.. the definition of slow.. should be copying files between two usb drives in an apple network using wireless. You will experience new levels of pain and suffering.. likened to the belly of the Sarlacc.

Troubling extending wireless network with Time Capsule and Airport Extreme

I am trying to set up and extend a wireless network in my house, but it’s not working right. I have two Airport/Capsule units in the house:
2TB Time Capsule (Dual-Band II)
1 Airport Extreme (Dual Band)
I have the Verizon Fios router as my gateway to the internet, and also as my DHCP server. I have also tested the ethernet ports in my house to verify that they work, and that I can get a DHCP-issued IP address.
Now, my Verizon router has WiFI, and it’s still on. I am not using it though except to troubleshoot. So far as I understand, this should not cause a problem.
Base station setup
So I setup the TC to Create A New Wireless Network, on the ethernet network it’s on (Dlink switch plugged into Verizon router). I set it up in Bridge Mode (as opposed to having it dole out IPs, since the Verizon router does this already). The TC gets a valid IP, and my wireless device connect to it without a problem. I have checked “Allow this network to be expanded” under Wireless settings.
Extended station setup
The AE Dual-Band is plugged into the Ethernet, and is reset to Factory Settings. I name it “Airport Extreme 2” and I chose “I want Airport Extreme to join my current network.” The other two options are: “I want to create a new wireless network” and “I want to replace and existing base station or wireless router with Airport Extreme.”
I chose to “join,” I select “I want to connect Airport Extreme to my network using Ethernet to extend my existing wireless network.” The other options are to disable wireless entirely, or to “wirelessly join my current network.” On the next page it asks me to select the device or network that the Airport Extreme will connect to using the Ethernet. I set it to the Time Capsule.
Results:
Access near the Airport Extreme 2 is incredibly slow. Speedtest shows I am getting less than 1Mbps. Worse yet, my mail client won’t connect. It just times out.
What I had hoped was that the AE would connect via Ethernet to the network, and just bring the wireless network to the other side of the house. Instead it almost seems as though it is just re-amplifying the TC’s signal. Otherwise, why is performance so bad?
Thanks to anyone with some insight here!

Hello Kennuff. Welcome to the Apple Discussions!
Since you have the ability to connect all of the routers by Ethernet, there is no need to configure the Time Capsule (TC) & 802.11n AirPort Extreme Base Station (AEBSn) for a dynamic WDS (aka, extending a network). This option is only when the routers do NOT have an Ethernet connection between them.
Instead, you want to configure the TC & AEBSn in a "roaming" network. I suggest starting by performing either a "hard" or "factory default" reset on both.
Next be sure that both the TC & AEBSn are on the same Ethernet subnet coming from the Verizon-supplied router.
Configure the TC & AEBSn as follows:
AirPort Utility > Select the TC or AEBSn > Manual Setup > AirPort > Wireless
o Wireless Mode = Create a wireless network
o Allow this network to be extended: <not checked>
o Radio Mode: <leave the default or if you require a specific mode make sure both routers are configured the same>
o Wireless Security: <configure both routers the same>
AirPort Utility > Select the TC or AEBSn > Manual Setup > Internet > Internet Connection
o Connection Sharing = Off (Bridge Mode)

Need to create a Separate Wifi Network @ Office

At my small biz, I have AT&T (formerly Bellsouth) High Speed DSL... Runs into a Motorla DSL Modem for the Internet connection, then to a Cisco PIX for our Firewall. I can hang an Airport off the network, but our iOS devices can't pull Exchange Email if connected to the wifi.
So I'd like to hang the Airport off the DSL Modem... I first tried with an old Airport Express, wifi network was fine, but couldn't get Internet no matter how I set it up. The DSL Modem is making the connection, but I'm unsure how I create the Separate Wifi Network with the Airport connected directly to it.
I'm going to use a Time Capsule A1254 rather than the Airport Express... a little direction would certainly help.
Thanks! Scott

The Motorola is a Netopia 3347-02-1022 gateway device. We do authenticate with PPPoE, which is being managed on the 3347. We have a static IP, the PIX gets the internet from the 3347, our domain controller handles DHCP.
I assume that you are getting a single static Public IP address from your ISP and that is is "applied" to the 3347 gateway's WAN interface ... correct? I am also assuming that the 3347 is handling the NAT service with your DC handling DHCP for the issuance of Private IP addresses on the local network.
The AirPorts are consumer-grade routers and do not offer any VLAN functionality ... other than the Guest network feature of the 802.11n Extremes and Time Capsules. As such, any VLAN-type network "subnetting" would not be possible. At best, you can enable NAT & DHCP in combination to allow the wired/wireless networks behind the AirPort's NAT to have a different Private IP address range. Note: There is no option to disable DHCP separately with the AirPorts. You basically have three options: 1) NAT & DHCP enabled, 2) NAT disabled & DHCP enabled, or 3) Both NAT & DHCP disabled. These options are controlled with the Connection Sharing option on the Internet Connection tab of the AirPort Utility.

Network diagnostics asks for password for wireless network with no security

hi
I am trying to connect my Mac Pro to a wireless network which has no security settings. Other Macs in the house connect to the network with no problem, but the Mac Pro doesn't. I am setting up a new network as I have moved house. In the previous house the wireless worked fine on the Mac Pro.
When I click on the Airport Icon in the menu bar, the search wheel shows and it finds the network, but when I click on the name of the network typically it doesn't connect. Occasionally it does connect, and I briefly have internet access, but then the number of bars on the Airport Icon gradually reduce and then I can't connect again.
When I run Network Diagnostics from Safari, it finds the network also, but then typically asks for a WEP password for the Wireless Network when I haven't added any security to the network (occasionally it doesn't ask for a password and I can connect briefly)
I have tried resetting my Time Capsule and creating a new wireless network with a different name, but still experience the same issues.
I wonder if someone has any ideas as to what might be going on, and how I might be able to troubleshoot this.
Thanks
Nick

It is one of mine. Yes. It connects to it no problem, just doesn't connect to the actual internet. Network diagnostics has all green lights until the ISP and/or Internet point. If I walk through diagnostics, it will get to the point where it says that the network requires a WEP password. I don't know why it does that because my network is not password-protected (husband claims it doesn't work well with his VPN system to get into work network). If I leave it blank, the connection will work. Eventually, after the computer is put to sleep, I will have the same problem upon waking up. I just tried renaming the network and removing all preferred networks and rebooting. Let's see how that works.

HT1178 Do I want to create a new wireless network or join my current network? I can't connect an ethernet cable to the Mac / printer and to the wireless modem at same time - in two different rooms.

I am trying to set up Time Capsule so that I can do my first backup (after 1 1/2 years!) with Time Machine. I have read other forums, but in each case they instructions eventually do not apply.
I have connected my TC to my existing wireless router. This sits in a bedroom and cannot be moved as a rental home.
I have plugged in the TC and updated the software.
Now - do I want to A Create a New Wireless Network (remember I can't connect the TC to Mac using an Ethernet cable). B Replace an existing base station or wireless router with TC (only intend to use for TM as don't know other benefits as of yet). or C want TC to join current network.
Thinking C. If I choose C, it then asks A TC to wireless join current network (NO as already connected using Ethernet). B want to connect TC to my network using Ethernet to extend my existing wireless network. C want to disable the wireless network on this TC and connect it to my computer or network using Ethernet - CANNOT do this as devices can not be in the same room.
Or do I want to create new wireless network - first set of questions - choice A? What is the benefit to creating a new one when I won't be in this rental house for longer than 18 more months??
Please help and quickly! Thanks!

Let me suggest some things.
But first ask exactly what wireless router you have now and what type of broadband service?
Are you happy with the wireless on the current router? If so, then you can plug the TC straight into whatever computer you have by ethernet, short 1M cord with no connection to the network. And use it without affecting your existing network at all. This is trivial setup.
Although you don't say exactly what Mac and printer you are using, is it a desktop? Laptop it is definitely easier not to plug it in, but a desktop you can plug in the TC and it will all sit happily together.
How is the printer connected and to what?
I am not sure why you need such quick help.. this is all minor setup stuff.. and 18months in todays world is like permanent man.
Your multiple A, B, C are more confusing than helpful.
The best choices without more info.. are to replace the existing wireless router with the TC. ie your option B.. but how to do this depends on the type of connection. Is it cable or adsl? Can you easily bridge the existing modem router.. if that is what it is?
Think carefully in the ideal world what would you like..
and what do you have..
We can probably suggest ways and means to fit what you like to what you have.. without introducing a stack of options that are doing your head in.

I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM. My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore. Connected those drives to TM via firewire and could see the drives and access them.
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc. I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads. Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system. I really didn't want to monkey around too much with my system. But are there other options to connect the new TC. Can't find info anywhere for this and called apple who gave me the info above. after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light or repair it in disk utility if it should become corrupted.
For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working. Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
Now a rant. I can't believe in this wireless age that Apple would make a product that cant join a wireless net work. The apple rep said i could return it and look for the previous TC that would join an existing wireless network. Are we going backwards?
Thanks!
lennydas

Ok... it is getting a bit clearer but there are still some questions.
I connect to the internet via airport only and it is pretty fast.
I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc.
I think this is mistaken.
Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
If the computer is close it will be faster than the FIOS.
You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC. the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
Thanks again!
You cannot extend to a non-apple wireless router.
You cannot use join a wireless network because when you do the ethernet ports will be cut off.
But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
Join in the express is the only apple router that still allows an ethernet connection.
For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

Unable to create a wireless network with my airport express. Please help!

I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
Tom

Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Creating a Separate Wireless Network With no Ethernet

Similar Messages

Maybe you are looking for