Creating a Temperature setpoint Profile Automatically

Hello!!!
I would like to get some help in the following. I am using the PID setpoint profile vi to control a furnace. Usually the temperature setpoint profile that I use is a cluster of time and temperature with values that I put manually. I wonder if it possible to create a temperature profile automatically (setting only the final temperature, of course keeping constant the temperature increase rate). What I really want is to have a front panel where the furnace operator will set only the final temperature (of course I would have considered a constant temperature increase rate)
Thank you in advance

Hi Thorfano
Can you describe your temperature profile in detail. If you have a linear system, you should be able to just place a setting in your PID and the feedback will cause the necessary gains to reach this.
Thank You
Eric Reid
National Instruments
Motion R&D

Similar Messages

Importance of precise colour temperature when creating dual-illuminant DNG profile

I own an X-Rite ColorChecker Passport and would like to use it to create a dual-illuminant profile for my camera (and every lens combination) to use in LightRoom.
After extensive research I have a few lingering questions:
1)      How important is it to nail the colour temperature. Do you *absolutely have to* photograph the ColorChecker under Illuminant A and D65, respectively, down to the last Kelvin?
2)      If I don’t nail it down that precisely, will the resulting profile be any less accurate?
3)      If getting the respective colour temperatures exactly right is indeed that important, is it OK to use 2 diffused and gelled speedlites with Lee/Rosco color correcting gels to illuminate the Colorchecker? (The Lee / Rosco gels do not have the exact CTO gel for the 2850K specified in the DNG specification for Illuminant A, but it gets close)
4)      If it will really aid profile accuracy, how does one get hold of reliable/certified light bulbs that produce the required colour temperatures? (I’m in the UK)
Your advice will be greatly appreciated.

The exact color temperatures (in Kelvin) are not that important within the standard daylight range (above 4000 K), because large number changes in color temperature actually represent small differences as far as camera color profiles go.
What is more important (rather than the exact number) is the spectral characteristics of the illumination. This isn't easy to characterize for the end user, but you can think of it in terms of bulb type. Most compact fluorescents are spectrally very different from actual daylight (even if the bulb is indicated as being "full spectrum"), for instance. My recommendation is to create a profile for the type of lighting you will be under, rather than trying to match the exact numbers.

To create the follow up transaction automatically on status change in sap crm?

To create the follow up transaction automatically on status change in sap crm? If yes, how to make the setting for this?

Hi vishal,
As per the requirement transaction type is activity(ACTI) & sales order(TA). when the take order objective is complete system automaticaly craete a new activity of tele sales call or metting with wholesaler.
this is requirement of client.
now i am already create all type of transaction types of activity & sales order & create follow up transaction also. i have doam already create action profile also but when i am assign this action profile to transaction & try to create an sales order no follow up transaction could be create automatically. i think the condition is not right so please help me out in this. what should be the start & schedulec condition for this scenerio

Hi,for gererating parter profiles automatically usint t-code bd64.

hi.
i wonna send idoc from ecc to xi.
and i am gonna use filter function of distribution model (bd64) to filter idoc according to the certain criteria i defined.
i have created model view in the ecc.
but there are not the string "No filter set" under my message type,so i can not double click it to create a filter.
why?
and that i have successfuly distributed it to xi ,because i have seen the identical model view in the xi.
next,
i am gonna generate parther profile automatically.
so,
i choose menu item "environment--> generate parter profile" using bd64 in XI to open a screen,and fill partner system,clicked execute button.
but a message occurs on the screen:
No message have been defined for the selection conditions in the model.
what' s wrong with the problem?

> i am gonna generate parther profile automatically.
>
> so,
>
> i choose menu item "environment--> generate parter profile" using bd64 in XI to open a screen,and fill partner system,clicked execute button.
>
> but a message occurs on the screen:
>
> No message have been defined for the selection conditions in the model.
>
>
> what' s wrong with the problem?
Not sure if I catch on, did you run bd64 on XI? ... Generally, after you have created model view on sender R/3 system, you should save it. Then, chose a model view for which you want to generate a partner profile and go to the menu "environment--> generate parter profile". Then partner profile will be generated.
Regards,
Jakub

Error while creating Rough cut planning profile

Facing the following error while creating rough cut planning profile (mc35) in SOP for product group. "Work center x plant y does not exist for task list type 3". pls advise- do i need to create tsk list for product group? pls advise with tcode to be used.

pls check the (task list ) usage you have maintained in the Work center.
In OP45 , pls ensure that for the usage ,
task list type 3 (Rough cut planning profile) is included.
If it is not included there , pls include the TL type 3 for your usage and now the prob will get solved.
Regards.,
Sheik

Error creating a new user profile service application: The specified database is not a valid synchronization database

When trying to create a new user profile service application on a new SharePoint install I get the following error:
"The specified database is not a valid synchronization database"
The installation then fails and does not create the third database.
I found some threads with similar problems but it involved upgrading an existing db. In this case we want to create a new one. Here is the relevant ULS log info:
Starting schema provisioning of SynchronizationDatabase 'SP15_TEST_ENT_SyncDB'
Provisioning the SP15_TEST_ENT_SyncDB database with the script at C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\15\Template\SQL\SPS\drop_procs.sql.
Provisioning the SP15_TEST_ENT_SyncDB database with a script stream.
Ensuring that the SP15_TEST_ENT_SyncDB database exists . . .
The SP15_TEST_ENT_SyncDB database does not exist.
It will now be created.
Setting the AutoClose option to False on the database SP15_TEST_ENT_SyncDB.
Setting the ArithAbort option to True on the database SP15_TEST_ENT_SyncDB.
Setting the TruncLogOnChkpt option to True on the database SP15_TEST_ENT_SyncDB.
Starting schema evaluation of existing SynchronizationDatabase 'SP15_TEST_ENT_SyncDB'
Validate Database: validating sync database
Validate Database: validation failed: Error code -2
Application error when access /_admin/NewProfileServiceApplicationSettings.aspx, Error=The specified database is not a valid synchronization database
at Microsoft.Office.Server.Administration.SynchronizationDatabase.Provision()
at Microsoft.Office.Server.Administration.UserProfileApplication.Provision()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.DoCreateApplication()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.OnOkButtonClick(Object sender, EventArgs e)
at System.EventHandler.Invoke(Object sender, EventArgs e)
at System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument)
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
Microsoft.SharePoint.Administration.SPDatabaseException: The specified database is not a valid synchronization database
at Microsoft.Office.Server.Administration.SynchronizationDatabase.Provision()
at Microsoft.Office.Server.Administration.UserProfileApplication.Provision()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.DoCreateApplication()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.OnOkButtonClick(Object sender, EventArgs e)
at System.EventHandler.Invoke(Object sender, EventArgs e)
at System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument)
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
Getting Error Message for Exception System.Web.HttpUnhandledException (0x80004005): Exception of type 'System.Web.HttpUnhandledException' was thrown. ---> Microsoft.SharePoint.Administration.SPDatabaseException:
The specified database is not a valid synchronization database
at Microsoft.Office.Server.Administration.SynchronizationDatabase.Provision()
at Microsoft.Office.Server.Administration.UserProfileApplication.Provision()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.DoCreateApplication()
at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.NewProfileServiceSettingsPage.OnOkButtonClick(Object sender, EventArgs e)
at System.EventHandler.Invoke(Object sender, EventArgs e)
at System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument)
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.HandleError(Exception e)
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest()
at System.Web.UI.Page.ProcessRequest(HttpContext context)
at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)
I Tried to create another one under a different name (databases also) and I get the same error.
The SharePoint instance has the march mandatory update installed. The sql instance we are using is an existing SQL cluster for other SharePoint poc's.
Has anybody seen this issue before?

I had the same problem and could not figure out what was wrong for the longest time. I then had the idea to check in the model system database to see if there were any extra custom tables in that database. Any tables that are in the model database
are put into any new database when it is created. I had some custom tables in the model database so I deleted the custom tables in the model database and deleted the failed user profile service application and its databases and then tried to recreate
the user profile service application again and it worked with no errors

Error while creating rough cut plannin profile using Info structure

Hi,
I got the following error while creating rough cut planning profile for Info structure,
Capacity planning is not possible for this info structure S504
Message no. MA489
Diagnosis
In the planning parameters for info structure S504, no key figure for capacity planning has been entered.
Procedure
If you want to capacity planning to be possible for this info structure, you need to enter a capacity key figure in the planning parameters for the info structure in the Implementation Guide.
The info structure which i used here is created by me. Can any one help me to overcome this error
Waiting for your replies
G.Muthamil Murugan.

Hi addy,
Thanks for your reply. I have maintained the following Info structure which I created,
Under characteristic I have maintained the following,
1.Sales Organisation.
2.Sales group
3. Sales office
4. Distribution channel
5.Division
6.Material
Under Key figure I have maintain the following,
1. Order items
2. Production
3.Sales
4. Stock level
5. Target stock level
6. Day's Supply
7. available capacity
8.Target days supply
I don t know where i did mistake. can you correct me.
Regards,
Muthamil Murugan.G

Creating a new application profile

Hi Hyperion Gurus,
Need your advice on an issue we are facing now:
In our current application (HFM 11.1.2.2. EPMA), we have created our application profile with only English as the language. We have 3 applications residing on our current profile.
We now have a requirement as to include Japanese as a language. I am aware that I can not make changes to the alias dimension in the existing application. This means that we will have to create a new application profile.
My question is: What will happen to the existing shared library that we use for our current applications? When I create a new application will it impact the old ones?
Any thoughts and ideas are greatly appreciated!
Thanks,
Steffi.

Hi Thanos,
so I did create a new application profile and included the languages I needed. And when I created the application, the Alias dimension is blank.
Here are the steps that I followed:
1. Create a new application profile from the desktop client.
2. Opened work space and created New application from Administer > Consolidation Administration.
3. Registered the application to Shared Services.
4. Transformed the classic app to EPMA in order to use the Shared library
Not sure what I am missing. I have attached a screenshot of the dimension library from my new application.

Creating a New Document Profile CS5

I have created a New Document Profile that I want to use as a base when starting Ilustrator work. I cleared pallettes colors, brushes, symbols etc and created 3 new common layers etc. When I select my file from the New Document Profiles pull down menu the Layers pallette opens with only a blank Layer1 .The work on my custom Layers that I would like as masters is gone.

Where did you save the new file?
Looks like you're right. Seems only way is to Save the file as a Template file and use New from template from the file menu.

How do i create a 2nd user profile that is very different, on same machine?

Greetings,
On my Mac Book Pro, I have created a second user profile that I will also use. But I want it only to load with no history of what I have done on my current profile on this same macbook pro. Want also a fresh instance of Firefox. Do you follow what I am trying to do?
thanks

Yes, should be straight forward...
System Preferences>Accounts, unlock the lock, click on the little plus icon, fill in the username & password, log out & into the new account.

How to create a project in PS automatically wen it is created in cProjects.

Hai experts,
How to create a project in PS automatically wen it is created in cProjects.
After creating project in cProjects wen i flagged to transfer it is not transferring to PS...
How to achieve this...
Thanx in advance...

hi
Try with following settings if you have not done:
1) In define project type, for for accounting integration , select scenario as: Accounting integration in my SAPERP and type of transfer as : Always Automatic when saving
2) For Define object link for object type , define proxy class for WBS element and Project definition(PS)
Also define RFC for Single object Controlling on WBS element in Object types for object links.
3) For Accounting integration in Make general settings, for your project type select frame09 for your object type single object controlling on Internal order
4) Define CO scenario CPR2 with Strategy sequence as SAP040 in period end closing, costing sheet as standard and Costing variant as PC02(Internal Order)
5) In CO scanrio maintenance view, for your project type select contolling method as Internal Order( Project Definition, Automatic)
With these settings I am able to create a PS project from cProject when I save a cProject.
Regards,
Niraj

Creating the job to execute automatically the program RSWUWFML2

Hi guys,
Iu2019m setting up the job to send Workitems to internet periodically with the program RSWUWFML2, when I create the job It ask me for a responsible user in the u201Cstepu201D, this user is going to be the one to execute this job, I usually call this user u201CWORKFLOWu201D and I need to set the Email account (Workflow) for this user (Tcode SU01) because on this Email account the system will be sending a kind of log for the workitems sent to users and which of them have been opened by the user.
The question I have is in SU01 which u201CROLESu201D have to be set for this user to be able to make all the thinks to send the workitmes to the users and send this Email as a log and make all the things related to execute the RSWUWFML2 report.
Tanks a lot

>
FelipeUribe wrote:
> Hi Ravi, tanks a lot for your answer, The problem using user WF-BACH as a user to be placed in the Job (Tcode SM36 -> Step u2026 field u201CUser = Background User Name for Authorization Checku201D) is that I get an error because this user canu2019t be a u201Ccommunicationu201D useru2026.the Tcode SWU3 create this user WF-BATCH automatically with this features.
Hi Felipe
Here's Help from the user type field in SU01 for B it says,
System 'B'
Use the system user type for internal system processes (-> background processing) or system-related processes (-> ALE, workflow, TMS, CUA).
Dialog logon (using SAP GUI) is not possible.
A user of this type is excluded from the general settings for password validity. Only user administrators can change the password using transaction SU01 (Goto -> Change Password).
Multiple logons are permissible.
I have checked one of our productive systems and it is set to B for WF-BATCH. The error message you get is because your WF-BATCH is a C type.
Hope this helps.
Good Luck
Ravi

BUG: Access Connect Abort, when I create a new network profile.

Where can I report bugs?
My system is windows xp sp2 on X60.
I have been using AC-4.42(Access Connection) for a long time. And before, there is no problem when I added new network profile into it.
But yesterday, I wanted to add a new profile into it. I opened the "create profile" window and input the name of the new profile (I have two network adapters, wired and wireless. So by default, the both are selected. And I left the default selection unchanged.), then "Next". The 2nd window is about wireless config, I configured everything, then go on "Next", at this moment, an error occured and AC aborted with four error windows. The titles of those windows are "ACMainGUI.exe error" and "ACMainGUIWnd: ACMainGUI.exe".
Then I did it again, I opened the "create profile" window, and this time, in this (1st) window, I changed the selection of network adapter, besides inputing the name of the new profile. I only selected the wired adapter, and then "Next". Sadly, this time the 2nd(next) window did not appear(pop up) at all. Instead, those four error windows poped up one by one. AC aborted again.
I repeated the above operations many times, and everytime, AC aborted.
So I went to the online "support and download" to look for some updates about AC. And I found AC-4.52 with luck. After downloading and installing, unfortunately the problem still exists. AC-4.52 still aborts when I create a new network profile.
So now, what to do. I have no ways. I am expecting the developers could note this problem and fix it and give me a newer update as soon as possible.
Sigh...

I have exactly the same issue. Next to the actions mentioned by ixbm I have also fully uninstalled and reinstalled the AC-4.52, but this didn't help.
Any idea on how to solve, installing older version?
regards,
Bart

How do I create a new lens profile?

How do I creat a new lens profile for a Canon EF135mm f/2 and EF200 f/2.8 in lightroom 3.3?

Hi Simon,
Thanks for your reply. I figured it out, I downloaded the new version of Raw 6.3 and now I have the lens profile and others such as crop constraint and
chromatic abrerrations. I was looking for these items in Photoshop Raw
Thanks,
Aideen
If I understand you correctly, you found and downloaded a lens profile that matches your camera and lens, and you don't see the profile in LR?
1. Make sure that you relaunch LR after you downloaded the lens profiles.
2. The type of lens profiles (raw or non-raw) matches your image type (raw or non-raw). Namely you can only apply raw lens profiles to raw image files and vice versa for the non-raw profiles.
-Simon
>

Create two different printer profiles in ePrintCenter.

Dear,
I want to create two different printer profiles: one "color" printer and one "black & white" printer.
In the ePrintCenter you can only create one kind of profile. (Associated with one e-mail address)
Is it possible to set this up?
Regards.
Printer: HP OfficeJet 6500A

Hello skeg,
At this point there is not a way to create two different profiles on an account in ePrintCenter. The only way to switch between the two would be manually on the "ePrint Settings" within ePrintCenter.
If you were trying to do this from an iPhone or Android phone it would be possible to download the HP ePrint home & biz app which would allow you more options regarding printing in color and paper size and type.
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Creating a Temperature setpoint Profile Automatically

Similar Messages

Maybe you are looking for