Creating Cluster Enviroment in BO XI R3.1

Hi all,
I need to create clustered environment in BO XI R3.1 SP3 Windows Server having Oracle 10g database CMC
Apache Tomcat server, can anyone send the document with steps to do it.
Regards,
Shanthakumar

Hi,
this is pointed out in the admin Guide of BOE XI 3.1
Regards
-Seb.

Similar Messages

Unable to create cluster, hangs on forming cluster

Hi all,
I am trying to create a 2 node cluster on two x64 Windows Server 2008 Enterprise edition servers. I am running the setup from the failover cluster MMC and it seems to run ok right up to the point where the snap-in says creating cluster. Then it seems to hang on "forming cluster" and a message pops up saying "The operation is taking longer than expected". A counter comes up and when it hits 2 minutes the wizard cancels and another message comes up "Unable to sucessfully cleanup".
The validation runs successfully before I start trying to create the cluster. The hardware involved is a HP EVA 6000, two Dell 2950's
I have included the report generated by the create cluster wizard below and the error from the event log on one of the machines (the error is the same on both machines).
Is there anything I can do to give me a better indication of what is happening, so I can resolve this issue or does anyone have any suggestions for me?
Thanks in advance.
Anthony
Create Cluster Log
==================
Beginning to configure the cluster <cluster>.
Initializing Cluster <cluster>.
Validating cluster state on node <Node1>
Searching the domain for computer object 'cluster'.
Creating a new computer object for 'cluster' in the domain.
Configuring computer object 'cluster' as cluster name object.
Validating installation of the Network FT Driver on node <Node1>
Validating installation of the Cluster Disk Driver on node <Node1>
Configuring Cluster Service on node <Node1>
Validating installation of the Network FT Driver on node <Node2>
Validating installation of the Cluster Disk Driver on node <Node2>
Configuring Cluster Service on node <Node2>
Waiting for notification that Cluster service on node <Node2>
Forming cluster '<cluster>'.
Unable to successfully cleanup.
To troubleshoot cluster creation problems, run the Validate a Configuration wizard on the servers you want to cluster.
Event Log
=========
Log Name:      System
Source:        Microsoft-Windows-FailoverClustering
Date:          29/08/2008 19:43:14
Event ID:      1570
Task Category: None
Level:         Critical
Keywords:
User:          SYSTEM
Computer:      <NODE 2>
Description:
Node 'NODE2' failed to establish a communication session while joining the cluster. This was due to an authentication failure. Please verify that the nodes are running compatible versions of the cluster service software.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Microsoft-Windows-FailoverClustering" Guid="{baf908ea-3421-4ca9-9b84-6689b8c6f85f}" />
    <EventID>1570</EventID>
    <Version>0</Version>
    <Level>1</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8000000000000000</Keywords>
    <TimeCreated SystemTime="2008-08-29T18:43:14.294Z" />
    <EventRecordID>4481</EventRecordID>
    <Correlation />
    <Execution ProcessID="2412" ThreadID="3416" />
    <Channel>System</Channel>
    <Computer>NODE2</Computer>
    <Security UserID="S-1-5-18" />
</System>
<EventData>
    <Data Name="NodeName">node2</Data>
</EventData>
</Event>
====
I have also since tried creating the cluster with the firewall and no success.
I have tried creating the node from the other cluster and this did not work either
I tried creating a cluster with just a single node and this did create a cluster. I could not join the other node and the network name resource did not come online either. The below is from the event logs.
Log Name:      System
Source:        Microsoft-Windows-FailoverClustering
Date:          01/09/2008 12:42:44
Event ID:      1207
Task Category: Network Name Resource
Level:         Error
Keywords:
User:          SYSTEM
Computer:      Node1.Domain
Description:
Cluster network name resource 'Cluster Name' cannot be brought online. The computer object associated with the resource could not be updated in domain 'Domain' for the following reason:
Unable to obtain the Primary Cluster Name Identity token.
The text for the associated error code is: An attempt has been made to operate on an impersonation token by a thread that is not currently impersonating a client.
The cluster identity 'CLUSTER$' may lack permissions required to update the object. Please work with your domain administrator to ensure that the cluster identity can update computer objects in the domain.

I am having the exact same issue... but these are on freshly created virtual machines... no group policy or anything...
I am 100% unable to create a Virtual Windows server 2012 failover cluster using two virtual fiber channel adapters to connect to the shared storage.
I've tried using GUI and powershell, I've tried adding all available storage, or not adding it, I've tried renaming the server and changing all the IP addresses....
To reproduce:
1. Create two identical Server 2012 virtual machines
(My Config: 4 CPU's, 4gb-8gb dynamic memory, 40gb HDD, two network cards (one for private, one for mgmt), two fiber cards to connect one to each vsan.)
2. Update both VM's to current windows updates
3. Add Failover Clustering role, Reboot, and try to create cluster.
Cluster passed all validation tests perfectly, but then it gets to "forming cluster" and times out =/
Any assistance would be greatly appreciate.

Error while creating cluster view

Hi all,
Requirement is to create cluster view copying cluster view VC_TABWU01 into custom view.
CV VC_TABWU01 has two data base views V_T093C_10 and V_T093U_01 I copied them both in to ZT093U_01 and ZT093C_10 and created a CV Z_TABWU01. Field dependence is set, when I am activating view I am getting message that screen 300 of ZT093U_01 is modified. I changed all possible options as standard view, kindly help me activating cluster view.
Error: The flow logic of the screen ZT093U_01 0300 is not that of a generated view maintenance list screen. Either the screen has been considerably modified manually, or the view which it is based on has no maintainable key.
Thanks
Krishna.

Need to add events in TMG. Solved with help of standard CV

Cluster Installation - SQL 2005 / 2003 - Creating cluster group

Hi All,
I am working on the cluster Installation in our environment and facing some issues at the time of installing first node MSCS Installation. let me summarize the activities done so far
Environment Details
Physical Disk :
G: (Physical Disk - SAN )
I : (Physical Disk - SAN )
C: Local disk
Q: (Physical Disk Quorum - SAN )
F: (Database and logs)
-- > SCS installed locally in the server in G drive
Virtual Hostname and IP : SeparateIP & cluster1
Node 1: Hostname and separate IP
Node 2 : hostname and Separate IP
Installed MSCS service and tested the same - its working fine
Installed SQL 2005 database in cluster mode and its working fine
Started installing SAP
Step 1: Installation of SCS instance in node A (Used F drive) - Successfull Installed
Step 2: Installation of First node MSCS in node A
Here I am facing an issue, in the end phase of the installation it will ask for creating cluster group -- > There I need to define the Global disk as F (Which is defined at the time of installing SCS instance) - But i dont see that disk is available in the drop down box .
Is there any other workaround to bring the Global disk while creating the cluster group (First node MSCS installation)
Looking forward for your suggestions
Thanks and Regards
Vijay

Regret for the late update
112266 solved my problem and In my case, I have bisected the disk as two but in the cluster environment that should not be the case. Ensure the the same in disk management
Regards
Vijay

Pls help in creating cluster view

Pls help in creating cluster view
regards
jindow

Hi,
Please try this and use BSEG as an example.
1. Go to SE12.
2. Enter BSEG
3. Click Display button
4. Go to Delivery and Maintenance' tab.
5. You should be able to see Pool/cluster RFBLG.
6. Double click RFBLG and then click Where-Used list button (CTRLSHIFTF3).
7. Select Table option and click Execute button.
8. System will show all the table that belong to this pool/cluster.
For Pool/Cluster REGUC, it is only used in table REGUP.
Look at the below link
Re: Define view for cluster table?
Regards,
Priyanka.

Create Cluster Wizard in SCVMM 2012 doesn't have IP Address page

i installed the SCVMM 2012 version 3.0.6019.0.
When i use the Create Hyper-V Cluster under Fabric page to create a Cluster.
the Create Cluster Wizard doesn't have the IP Address page to let me input the IP for the Cluster.
after i answer all the wizard, the Install Cluster job shown Error 25325
The cluster creation failed because of error At least one IP address needs to be configured..
so, how to solve it?
thanks alot.

Old thread..
But I got the same problem creating a cluster on SCVMM 2012 R2. To get around it I instead created the cluster using powershell and it worked great:
$HostName1 = "HOST01"
$HostName2 = "HOST02"
$Clustername = "CLUSTER01"
$ClusterIP = "192.168.1.50"
$VMMRunAsAccount = "VMM_AdminAccount"
$credential = Get-SCRunAsAccount -Name $VMMRunAsAccount
$hostsList = @()
$hostsList += Get-SCVMHost -Computername $HostName1
$hostsList += Get-SCVMHost -Computername $HostName2
Install-SCVMHostCluster -ClusterName $Clustername -VMHost $hostsList -RunAsynchronously -Credential $credential -ClusterIPAddress $ClusterIP
_____________________________________ /Michael R

Problem with APEX 4.0 - "ORA-20001: Error with: GRANT CREATE CLUSTER "

I have a workspace which I've succesfully created with schema A.
However when i try to assign an additional schema to it, schema B, I get the following error message :-
"ORA-20001: Error with: GRANT CREATE CLUSTER TO "BI_SOURCES" ORA-01031: insufficient privileges"
i've tried granting "create cluster with admin option' to users A,B,anonymous AND APEX_040000. FLOWS_030000 already has these privileges.
Anybody any ideas ?
regs
johnnie
Edited by: johnnie d on 31-Aug-2011 10:58

I have experience the similiar problem. The error message: Invalid exist/not exist condition: ORA 2001 Query must begin with Select or With.
I have home page and concept review report page below home page. And Concept review form under the report page. The error is display in all of the three pages. I checked carefully and still not able to find where the error come from. Can you please help? All the report region and form region have the select statement, is it from the LOVs? Home
Concept review report
Concept reveiw Form(for detail info)
Thank you!

Can u create cluster and pooled tables in real time

hi
can u create cluster and pooled tables in real time.can u send data base tables name of above one.

Hai Anil
For creating cluster tables first u have to create table pool ...
create a table and specify the fields and other tecnical settings and
then Goto EXTRAS --> Change Table Category and selct the Pooled table and activate it...
Then Create another table And specify the required fileds and also the settings and then
Goto EXTRAS --> Change Table Category and selct the Cluaster table and in Delivery and
Maintainence Properties mention the Pooled table that u created and activate it...
Regards
Sreeni

Cannot create cluster

Hi!
I installed JES2005Q1 AppServer 8.1 and wanted to create a cluster. But:
bash-3.00# ./asadmin create-cluster
CLI001 Invalid Command, create-cluster. Use "asadmin help" for a list of valid commands.
create-cluster is not a valid command. Also commands concerning node agents are missing.
I did not install Pointbase & Samples, might this be the cause for this?
Also in the administration web interface "Clusters", "Node Agents" and "Stand-Alone Instances" are missing in the tree.
thx for any ideas,
Chris

Ok, found it. It was simply the Standard Edition installed, not the Enterprise Edition...

Creating Cluster Fails

When using VMM 2012 R2 to create a cluster we are receiving this error. It goes all the way to step 1.5 Create Cluster and then throws this error. In the past we have created clusters with Failover Clustering and added them back into VMM but
would really like to get VMM to do what it says it can do.
Error (25325)
The cluster creation failed because of the following error: The network name '' is already used in the network..
Recommended Action
Please refer to cluster documentation for resolving cluster problems.
Is VMM trying to write to DNS? We have a DNS name reserved for the cluster address in Infoblox already. What other steps should we try? Our storage is coming from our SAN (IBM V7000) with Fiber and the hosts have the latest SDDDSM installed.
I am stumped currently.

Hi Sir,
>> I changed the DNS IP as for some reason the old IP was responding to ping so will have to track that down.
How are things going now ?
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

How to create cluster table

Hi
this is fazil.
Please tell me any body how to create cluster table.
Thanks & Regards
Fazil
[email protected]

Hi,
1. In the initial screen of the ABAP Dictionary select object type Table, enter a table name and choose Create.
The field maintenance screen for the table is displayed. Table type Transparent table is set as default.
2. Make the necessary entries in the Short description and Delivery class fields on the Attributes tab page. Then define the fields of the table.
Proceed as when creating a transparent table. Save your entries.
3. Choose Extras ® Change table category.
A dialog box appears in which you have to select the table type Pooled table or Cluster table.
4. Choose Select.
You return to the field maintenance screen for the table. Field Pool/cluster name is displayed on the Attributes tab page in addition to the standard fields.
5. Enter the name of the table pool or table cluster to which you want to assign the pooled table or cluster table in field Pool/cluster name
Note that the total key length of a pooled table may not exceed the key length of the associated table pool. The key of a cluster table must correspond to the key of the associated table cluster.
6. Proceed as when creating a transparent table (see Creating Tables). Remember that you cannot create indexes for pooled or cluster tables.
All the attributes of the technical settings can be maintained for pooled tables and cluster tables. Before you can access these attributes, however, you must convert the table to a transparent table.
Rgds,
P.Naganjana Reddy

2012 R2 Cluster - Issues creating cluster

New Dell VRTX server with 2 server blades. Installed Server 2012 R2 on both blades and all working ok.
Ran the 'Validate Configuration' wizard and all ok apart from Storage Spaces, which we won't need as we have hardware RAID.
Then ran create cluster wizard and works ok until it goes to create and then fails:-
Adding special permissions to the computer object failed.
Trying to add 'Full-Access' permissions for security principal
S-1-5-21-1054053922-559824688-2072063007-68696 to computer object
CN=UKWOR-CLUSTER01,OU=Cluster,OU=SERVER,OU=HAR,OU=UK,OU=AVL,DC=xxxx,DC=xxxx,DC=lan
failed. Verify that the user running create cluster has permissions to update
the computer object in Active Directory Domain Services. The parameter is
incorrect.
"CreateClusterNameCOIfNotExists (6888): Configuring Computer Object UKWOR-CLUSTER01 to act as the CNO on DC \\ xxx.lan"
"CreateClusterNameCOIfNotExists (6916): Configuring Cluster CNO resource."
"CreateClusterNameCOIfNotExists (6942): Cannot provide user special permissions to the object.
Error <87> (Step ErrorPutSD)."
"PhaseManager::EndPhase (235): Phase 109
"CreateNetworkName (4618): Failed to create Computer Object for NetName Cluster Name on DC \\ xxx.lan. Error 87."
I've tried this also by pre-creating the computer object (in the right OU and following guides online for setting the permissions, disabling it etc. I do not have Domain Admin rights as we are a large multi-national company. But I can create computer accounts
in my OU and I have given the administrator account that's logged into the servers the same rights on the relevant OU.
Any suggestions or ideas as to what I can do to progress with this as I've run out of ideas :(

Thanks for the info PMThomas,
@Lerun: For us it was permissions as well in the end. A quick fix I found to get arround it until you find the offending AD permissions is to create the new Cluster Computer Object in AD. Disable the account. Then go into security for the
Computer Object and disable inheritance, make sure you choose remove when promted. For us this must have removed the offending AD permissions as we could then create the cluster.
I've not managed to work out which permission it was yet. I guess I could test by removing each of the inheritted permissions one by one until the cluster wizard is successfull.
Heres a link to my post on our troubleshooting process if you fancy a LONG read!!
http://social.technet.microsoft.com/Forums/en-US/8d1c504b-c3fd-4eaf-8309-ef4e9fdbd82f/unable-to-create-a-new-cluster-on-our-domain?forum=winserverClustering

Creating cluster trying to remove disks.

Hi
I am going through the pain of trying to create a whole cloud environment using scvmm2012r2 so that it can then link in to the whole windows azure pack.
I have created what I think is the whole fabric which has been very very painful.
My question when trying to make all that setup work is the following.
When I try and create a hyperv cluster using scvmm I step through the wizard. First issue I have is:
I have defined a logical switch which has three vnics one for host management 2. Live migration. 3. Cluster workload.
When it comes to giving an ip it is only allowing me to select from the host management pool. I would have thought it should have been the cluster or live migration networks.
2nd question is when it gets to the disks to cluster. The servers are connecting to a fibre channel switch so can see other disks that are attached to other clusters. In the interface I can not untick those I don't want as part of this cluster. What have
I done wrong
in the image I have highlighted the disks that I want to remove but I cannot.
If I do this normally through fail over cluster manager then it is no issue.

Hi.
First thing first: when you create a Hyper-V Cluster, you will also create a Cluster Name Object in Active Directory, this will be the access point of this cluster and this also requires an IP adress. This IP adress is then on the management network - where
clients can access the cluster name object (so that VMM (as a client) can access the cluster - and manage the cluster). this is by design. You would leave cluster network and live migration out of this, as this is for internal cluster communication and live
migration traffic.
second, a cluster should only see the disks it should be using, and not any other disks used by other clusters. You must check your zoning here, as this is not best practice. a CSV can't be shared across several cluster.
I would suggest that you clean that up, and if you don'w want VMM to do this for you, you can create the cluster in failover cluster manager, add the required disks and the update the hosts in VMM so that they reflects the cluster you have created.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

SOA Clustering - Create cluster after domain creation

Hi all,
I can't manage to find out how to properly move a standalone soa server into a cluster created after the domain.
I would like to do the following :
1. Create a domain without any cluster --> All soa server deployments target a unique managed server
2. Create a cluster afterwards and associate the soa managed server to it
3. update all targets of soa server deployments to target the cluster instead of the initial managed server
--> I'm looking for a solution to do step 3 in a clean and automated way (That's looks a bit strange and painful to open every deployment and change the target one by one)
I run WLS 10.3.5
Thanks for your help.
Philippe

You can probably try by cloning the server1 to server2 and that way have everything from server1 to be replicated on server2. Once server2 is created, then create the cluster of soa servers and then update the deployments to be deployed on all the members of the cluster rather then individual servers. You can perform these steps from the weblogic console and record the setps to generate WLST script for the same. Once the scripts are created, you can tweak them up a bit to have automated script to perform the steps without human intervention.
-Bikash

How to name elements and create cluster of named elements

I wanted to detail the steps I found, so that others could more easily follow what I found going through these discussions. While there are numerous examples, they lack details such as function names and how to achieve the steps. Most of them seem to cover only arrays. I welcome corrections. I'm not saying this is the best way; it is, however, a simple detailed description of one way to do it.
I wanted to create a cluster of various data types that could then be manipulated by name. Unfortunately, simply wiring an existing cluster to a Bundle by Name.vi does not assign the existing labels of the elements to the name field of the cluster. I don't know why.
1. Create an input cluster with dummy constants of the proper data type for each element.
How do you create an input cluster? Searching functions finds no "Input Cluster" function.
The only way I found was to place a dummy Bundle by Name.vi , right-click at the top of the leftmost of the two rectangles and select Create, then Constant. The result looks like the attached Creating Input Cluster.PNG
You might as well delete the Bundle by Name.vi at this point, because the changes make to the input cluster will only be reflected when it is connected to a NEW Bundle by Name.vi
Next, for my purposes, I needed constants for DBL numeric, string, and array of strings. I started by placing one DBL and one string constant on the block diagram. I copied these to create the ones I needed. Make the labels visible and type in the names corresponding the Bundle Names desired.
Since there is no function called "String Array constant", it is necessary to place the "Array Constant" function on the Block Diagram, then drag a string constant into the empty right hand square of the Array Constant. It immediately changes color to show it is a string array.
Drag each of these constants into the input cluster so that they appear in the order desired. It is a bit of a pain because the square resizes tightly around the existing elements after each insertion. You have to keep expanding the box at the bottom by dragging its sizing handles, so you can be sure each item is added to the bottom of the list. When done, my input cluster looks like Completed Input Cluster.png attached.
2. Place a NEW Bundle by Name.vi on the Block Diagram. Wire the input cluster to the top of the left rectangle of the function. Drag the down sizing handle of the Bundle by Name.vi until all the elements of the cluster are visible. You will see the names and it will look like Bundle by Name with assigned names.png attached.
3. All that remains is to connect the data wires for the individual elements to the left side of each named block and wire the output cluster. The result is shown in Complete design producing cluster of named elements.PNG attached. (Since only three attachments seem to be allowed, this last will be in a follow-up post.)
Attachments:
Creating Input Cluster.PNG ‏3 KB
Completed Input Cluster.PNG ‏3 KB
Bundle by Name with assigned names.PNG ‏8 KB

I wanted to add a brief statement about EDITING cluster controls because newcomers to cluster usage (like myself). The HELP is good on creation but says nothing about modification. While it has been posted other places, I think a "newbie" might appreciate getting this info here.
To edit a cluster control, open the CTL file, then
Add a control by creating the control on the front panel, then save the control.
To remove a a control, delete the control, then save the control file.
(Simple enough)
To modify an existing control
1. Move the control out of the cluster into a blank VI.
2. SAVE the cluster control file (CTL).
3. Modify the control in the blank VI.
4. Drag the modified control back into the cluster control.
5. SAVE the cluster control file (CTL)
NOTE WELL: don't skip step 2.

Creating Cluster Enviroment in BO XI R3.1

Similar Messages

Maybe you are looking for