Creating Two Networks with Different Securities and Double NAT Error

I have a Time Capsule which is connected to my cable modem and an AirPort Extreme connected to my Time Capsule via the WAN port. I configured the AEBS to create a wireless network using WEP (I have a few devices that don't support WPA) so I can use two different wireless securities. The AEBS flashes the amber light and once I connect to its network, the AirPort Utility states that it has a "Double NAT" issue. I used my iPhone 5 to connect to the AEBS network and I can access the Internet just fine.
Is this issue one that can be resolved? If so, how? Or do I ignore the issue? If I ignore, what are the implications?
Thanks!

You need to configure the AEBS in Bridge Mode to eliminate the Double NAT error, which is slowing down your connection...and may likely cause other issues depending on how the network is configured.
If you do not know how to do this, we need to know what operating system you are using on the computer that is being used to configure and setup the AEBS.

Similar Messages

Can I sync two iPads with different users and email addresses on the same computer

Can I sync two IPads with different users and email addresses on the same computer.

yes, just make sure you turn off auto-sync to keep everything organized before you try syncing
on a pc
edit > preferences > devices - 'prevent ipads, iphones, and ipods from syncing automatically' needs to be checked

Two phones with different contacts and one computer?

how do i go about syncing two phones, with different contacts, to one computer?

If you are using Microsoft Outlook and syncing different contacts is your concern, you can set up a new Contacts folder for your iPhone (like "Jeff's Contacts") and set iTunes to sync that folder only to your iPhone. Create a second new Contacts folder for the other iPhone's contacts and do the same thing. Works great for my iPhone and my wife's iPhone, both synced to our home computer.

I installed my new iMac with my Macbook Pro 2008 backup and created a network with the iMac and now the Macbook Pro cannot get internet.

I installed my new iMac with my Macbook Pro 2008 back up. I created a iMac network with Airport extreme, but now my Macbook Pro cannot get internet. any ideas on why or what to do about it.

Hello 1BillyMac,
It seems you have a network conflict that isn't allowing your MacBook Pro to connect to the internet. This may be caused by both computers sharing identical network settings. You may want to consider creating a new network location on your MacBook Pro to assign new network settings. The following article will instruct you on how to do that:
OS X Yosemite: Add a network location
A network location is a group of network settings
A network location is a group of network settings for your various network services (Ethernet or Wi-Fi for example).
If you often change network settings, you may find switching between locations quicker and easier than repeatedly modifying individual groups of settings.
For example, you might want to make a location for “home,” where you connect to the Internet with a telephone modem, and a location for “office,” where you connect to your company network and the Internet using Ethernet or AirPort.
Choose Apple menu > System Preferences, then click Network.
Click the Location pop-up menu, choose Edit Locations, then click Add .
Enter a name for the location, then click Done.
Enter settings for each network connection service you want to use in that location.
After you create your locations, you can switch all of your network settings by clicking the Location pop-up menu and choosing a different location.
Thank you for contributing to Apple Support Communities.
Cheers,
Bobby_D

Is two networks with different WEP/WPA encryptions possible?

Hello I have the wireless wrh54g in my desktop pc using the WPA encryption and I have a laptop which can only accept WEP. How can I add another network in the Preferred Networks with the WEP encryption to accommodate my laptop? Please advise. Thanks. Menk
Solved!
Go to Solution.

The wireless security settings only apply to wireless links to the router, i.e. wireless computers or other wireless devices. Through these wireless links those devices connect to the LAN and through the router to the internet.
The wired ports on the router connect to the same LAN. Wired computers connect through the LAN and the router to the internet. There are no specific security settings for those wired ports. However has physical access to the router and those ports has access to the LAN. The wireless security settings have nothing to do with the wired ports. For instance, you could connect a wired network printer to one of the ports. You can also connect a desktop with a ethernet card to one of the ports. The desktop and a laptop connected wireless to the router can use the network printer. Both can also access the internet through the router.
Message Edited by gv on 09-25-2008 05:44 PM

Hi, my Macbook recently created a network with my name and password on accident. As i deleted this and tried to connect to my wifi, it didn't allow me to see or connect to my wifi router. Not sure what to do about this.

Hi, I recently unknowingly made a network for my wifi at my home. I deleted it because I didn't want to have a password on it because I live at home. When i tried to reconnect to the wifi, it didn't even show up in my wifi options. Can't connect to it or anything. Any help here?

"A lot of the time it just pops up on its own."
It will pop up if it detects there is an update and you haven't set it not to pop up automatically. You may need to reset the AE back to factory spec and set it up again. Read the manual for the reset.

How to create a contract with one supplier and two dealers?

Hi Gurus,
I have a contract with a supplier (eg. Apple), but the products and services are supplied by two dealers.
The supplier is the manufacturer and with whom the negotiation of prices is made.
The dealers are those who make the delivery of the products and services and who the payment is done.
How can I create a contract with these characteristics in SRM 7.0?
I don't want to create two contracts with same products and services for two suppliers (Dealer_1 and Dealer_2).
How can this be handled through business partner type "Vendor"?
In "Partner" section in "Header" --> "Basic data", I can only add 1 vendor.
The system is:
Component software: SRM_SERVER
Release: 700
Level: 0008
Support package: SAPKIBKV08
Thanks in advance and best regards,
Alonso Valenzuela

Hi Wadim,
I have a similar requirement to create order lines in an existing contract with reference using BAPI_CUSTOMERCONTRACT_CHANGE. The order lines get created in the contract. However, the condition types from the order line which i'm referencing are not getting referenced and are not getting added in the Contract's line after referencing.
Did you come across any such issue ? If yes , could you suggest the solution ?
Regards,
Venkat.

Can I backup two devices (with different documents) to one iCloud account? For example: iPad and iPhone, not everything is synced between the two, but I would like to backup each (seperately in the cloud), is this possible?

Hello Apple Community,
Can I backup two devices (with different documents) to one iCloud account?
For example: iPad Air and iPhone 5, not everything is synced between the two, but I would like to backup each (seperately in the cloud). Is this possible?
This way when I change from an old ipad to a new, I can restore with the ipad backup, and when I change from an old iphone to a new, I can restore from the
iphone backup.
Thank you in advance!

Terminology check here. Do you really mean a "CD"? There's a difference in Cloud behavior between content from a physical CD you ripped (which only has Cloud content if you have iTunes Match) and an "album" you bought from the iTunes Store.
Read references for Home Sharing.
iTunes: How to share music and video - http://support.apple.com/kb/HT2688 - about Music Sharing and Home Sharing
Home Sharing Support page - http://www.apple.com/support/homesharing/
iOS: Setting up Home Sharing on your device - http://support.apple.com/kb/ht4557 - "With Home Sharing in iOS 4.3 or later, you can stream your entire iTunes library over your home Wi-Fi network from your Mac or PC right to your iPhone, iPad, or iPod touch."
The above can get pretty complicated. You are probably best off by syncing both devices to a single library and/or updating the libraries on both computers to have the same content.

I have 2 apple id's with different apps and data saved under each. It's very annoying so now I want to create a new id with my primary email address I use now. If I do that is there any way to transfer all my saved apps and app data like game saves etc?

I have 2 apple id's with different apps and data saved under each. It's very annoying so now I want to create a new id with my primary email address I use now. If I do that is there any way to transfer all my saved apps and app data like game saves etc so I don't lose all of that information and can easily switch to a singular apple id?

Apple does not transfer content bought with one Apple ID to another Apple ID. Apple will not merge two Apple IDs.
If most of your content was bought with the Yahoo! Apple ID but you now want the Gmail address for your Apple ID, the trick will be to change the address used for the Yahoo ID with the Gmail address. However, to do that you must first free the Gmail address from that other Apple ID. Use the instructions from Apple to substitute another address that is not used as an Apple ID for your Gmail address in the Apple ID with the Gmail address. Then, when the Gmail address is no longer used in an Apple ID, you can use the same instructions to substitute the Gmail address for the Yahoo address in the Apple ID with the Yahoo address.
Changing the email address you use for your Apple ID -
http://support.apple.com/kb/HT5621

I have two users with different music on each itunes and i can only use one library, how do i use both for one iTouch?

i have two users with different music on each itunes and i can only use one library, how do i use both for one iTouch?

Chris, I believe this link may have the information you're looking for. Welcome to discussions!
http://docs.info.apple.com/article.html?artnum=300432

HT4528 Can I put the same information on two different i-phones with different numbers and different ID's?

Can I put the same information on two different i-phones with different numbers and different ID's?

Yes and no it really depends on what information you are putting on the devices.

I have 2? How do I sync selected photos from my IPad to my IMac w/o losing all photos on my IPad and getting the phoos o my IMac. ou see I have two IMacs with different sets of photos. Also want to convert all Apple works docs to pages docs on my IMac.

I have 2? How do I sync selected photos from my IPad to my IMac w/o losing all photos on my IPad which will be replaced with the photos on my IMac.You see I have two IMacs with different sets of photos. Also want to convert all Apple works docs to pages docs on my IMac. Is there and app available to do the former. many thanks. b

The iPad and related software is designed to sync with only one computer. I suggest transferring the photos from one of your iMacs to the other so that all photos are on one Mac. Same for all other files you want to sync over.
To get those AppleWorks files to the iPad you'll have to determine if Pages will open them. If it will then use the file sharing feature of iTunes to copy them to Pages on your pad.
If Pages will not open the AppleWorks files directly you'll have to save them in some format that Pages will read. These include but may not be limited to Pages and Word formats.

I have published two different blogs with different usernames and passwords

I have published two different blogs with different usernames and passwords. When I want to publish one, it goes through the whole process of publishing the other blog as well - and takes too long.
How can I publish each blog separately?

I have published two different blogs
I think you need to ask in the iWeb forum rather than this one (for iWork/Numbers):
http://discussions.apple.com/forum.jspa?forumID=1309

[svn:bz-trunk] 13716: since include-read-only is a server global setting, we can't have two channels with different value.

Revision: 13716
Revision: 13716
Author:   [email protected]
Date:     2010-01-22 09:26:12 -0800 (Fri, 22 Jan 2010)
Log Message:
since include-read-only is a server global setting, we can't have two channels with different value. remove the test for the include-read-only false. update the service-config.xml as well.
Modified Paths:
    blazeds/trunk/qa/apps/qa-regress/WEB-INF/flex/services-config.mods.xml
    blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ReadOn lyTest.mxml

You can give this a try on your Ultimate machine. While these are said to be for Vista, I used it on my Win 7 machine just fine and it fixed the problems I was having. Hope it works for you.
The problem is that Vista, by default, will only use NTLMv2 for authentication, which is not supported by Mac OS X's Windows Sharing service.
The other problem is the Minimum Session Security for NTVLM SSP based Clients.
To get around this:
1.     In Vista, open the Control Panel
2.     Switch to "Classic" view
3.     Double-click Administration Tools
4.     Double-click Local Security Policy
5.     Or Secpol.msc
6.     Expand "Local Policies" and select "Security Options"
7.     Alternate : Type secpol.msc to get editor up then
8.     Locate "Network Security: LAN Manager Authentication Level" in the list and double-click it.
9.     Change the setting from "Send NTMLv2 response only" to "Send LM & NTLM - use NTLMv2 session if negotiated"
10.     Network Security: Minimum session security for NTLM SSP Based (including secure RPC) Clients
11.     Change the setting from "require 128 bit" to unchecked (No Minimum)
12.     Click OK
the real difference between vista and windows 7 procedure is 10 and 11

Create two or more data sources and mapping to DSO

Hi,
I´m using SAP Netweaver BI 7.0.
If there are two or three data sources which have to be mapped to DSO which field from Data Sources has to be mapped to which field in DSO?
Is it possible to have only one DSO or should it be three DSOs because of the three Data Sources?
The thing is I have created one view out of three tables. For the view I have created one DSO. Everything worked fine. But now the requirements have changed because of currencies.
The view I have created is now mixing currencies because in the view is only one currency field, which is filled from the three tables. Two tables have different currencies and one table has one currency.
The one currency of the one table is important and should stay like it is.
I´m thinking about something like three different currency key fields in DSO which are mapped from data source. Also for every field of data source mapping with corresponding field in DSO.
Some hints? I have found articles in SDN about creating data sources and so on but they don´t help me in this matter.
Thank you in advance!

Thank you guys for explaining! I´m new to SAP BW and trying to better understand.
I`ll try it also with the view. It sounds "easier".
But if I´m doing it with the 3 data sources, that means that for each currency field of the data source I will need an corresponding currency field in the DSO for mapping.
Is it possible to have 3 times the 0Currency field in the DSO and each data source currency field will be mapped to the DSO?
If that would work the 0Currency has to be contained in the key figures.
But if the 0Currency is contained in each key figure will the assignment of currency work correct?
+For example:+
Data Source1:
Turnover in Euro.
(All currency is in Euro)
Data Source2:
Profit in Dollar.
Profit in Euro.
Profit in Yen.
Profit in different currencies available.
Data Source3:
Sales in Dollar.
Sales in Euro.
Sales in Yen.
Sales in different currencies available.
For mapping from DataSources to DSO if it is possible to have 3 times 0Currency in DSO:
Data Source1 currency fiield ---> DSO 0Currency
Data Source2 currency fiield ---> DSO 0Currency
Data Source3 currency fiield ---> DSO 0Currency
Does it make sense?

Creating Two Networks with Different Securities and Double NAT Error

Similar Messages

Maybe you are looking for