Creating two vlan in AP 1131

I need to create two vlan data and voice, with SSID, when I create two vlan with 31 for data 103 for voice with two different SSID, what ever vlan I created first is get broadcast, second one is not get broadcast, please let me know what I am missing.
Security is in open mode.

Hi Bala,
Have a look at this recent post from Dan @ Cisco. He nicely addresses this question;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Security%20and%20Network%20Management&topicID=.ee6e8c0&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cd4109c/2#selected_message
Hope this helps!
Rob

Similar Messages

Two VLANs on one switch port?

Currently we have the following
Cat 4003 with VLAN trunking turned on to multiple switches. Each port in those exterior switches is assigned to a vlan(we have about 60 different vlans).
What I would like to do is on those exterior switches have two vlans assigned to it.
We'd like to create a single IP Phone VLAN(let's call it 999) that can span our entire enterprise and would have dhcp deployed on it.
Each port is connected to an IP phone which has a 2 port switch in them. One port to the wall, one to the pc.
The switch ports on those phones support vlan tagging
How would setup an exterior switch to access 2 vlans that connect to 2 port switch on an IP phone?

To facilitate ease of deployment, use VTP so that you can centrally create the vlans and propagate to each exterior switch. Now I believe you already do have a layer 3 engine or router that does routing between all these vlans. What switches are used on teh exterior ? This is to find out if voice vlan support is available.
In cat switches, voice vlan is created using command,
set port auxiliaryvlan vlan
In IOS based switches,
int fa0/1
switchport mode trunk
switchport trunk encap dot1q
switchport trunk native vlan
switchport voice vlan
switchport priority cos extend 0
or
int fa0/1
switchport mode access
switchport access vlan
switchport voice vlan
I am not sure about support of voice/aux vlan in 4003. We will have check your other switch models/ software versions to determine support for this command.

How can i use IDSM-2 in inline mode for more than two VLANs?

can i use the IDSM-2 in inline mode to be ips to more than two VLANS
like this or it isn't
intrusion-detection module 5 data port 1 access-vlan 10,20,30,40,50
intrusion-detection module 5 data port 1 access-vlan 100,200
thank u all for your help

The IDSM-2 ports need to be configured as trunk ports with multiple vlans rather than as access ports.
http://www.cisco.com/en/US/partner/products/hw/vpndevc/ps4077/products_configuration_guide_chapter09186a00807517eb.html#wp1068377
And instead of creating an inline interface pair by pairing Gig0/7 with Gig0/8 within the IDSM-2 configuration, you would create inline vlan pairs.
With an inline vlan pair you pair 2 vlans on the same interface.
You can have up to 255 inline vlan pairs on each interface (assumining you keep the total traffic from all of the pairs within the IDSM-2s performance limit of around 500Mbps)
How to create inline vlan pairs:
http://www.cisco.com/en/US/partner/products/hw/vpndevc/ps4077/products_configuration_guide_chapter09186a00807517bb.html#wp1047852
The other aspect you need to be aware of is that not all IOS versions will support configuring the IDSM-2 data ports as trunk ports for inline vlan pairs.
Your best bet is to use 12.2(18)SXF4 or a later version on the 12.2(18)SXF train.
The 12.2(33)SR train does not currently support the trunk feature for the IDSM-2.

Small network, two VLANs, need some guidance

Hello. Big-time newbie here. I have a Cisco 2801 router and a few Cisco SG200-26 switches. I need to configure two VLANs: vlan10 for public wifi access and vlan20 for private staff use. I have fa0/0 configured with IP 192.168.1.2/24. This interface will be connected to an AT&T DSL gateway for Internet service. I have fa0/1 configured with IP 172.16.1.1/16. The goal is to provide Internet access to both VLANs, but no routing between VLANs. I am also enabling a DHCP pool of 172.16.10.0/22 intended for use on vlan10 (public wifi access) and another DHCP pool of 172.16.20.0/24 for vlan20 (private staff). I assume fa0/1 has to be configured for dot1q trunking and connected to a switch port also configured for trunking, yes? I also have WAPs that will need to serve up both VLANs. The WAPs I have are 121 and 2600 series. I assume I will be creating two SSIDs - one for each VLAN, yes?
I am looking to keep this as simple as possible.
What else do I need to consider? thank you in advance for your guidance.

thanks for ur valuable reply.
u r right that whenever we create a new db, oracle always assigns a new dbid. which will be different from the id of backupset db.
kindly explain me steps to perform, whether it is duplicate db case or standby.
how rman will recoganize the backupset.

Creating multiple vlans across multiple switches

Hi All,
How should I create multiple vlans across multiple switches?
For instance, I have two (primary/redudant) layer 3 (core) switches and four layer 2 access switches (Cisco 2960) for the hosts, and given these are the vlans/subnets to be created. Should I do it in the core switches only and it would just propagate through the access via VTP? Just trying to practice and learn.. Any help will be greatly appreciated:)
VLAN 100: [DHCP-workstations]
172.26.4.0/24
172.26.5.0/24
VLAN 200: [Servers]
172.16.1.0/24
172.16.2.0/24
VLAN 300: [Printers]
192.168.129.0/24
192.168.130.0/24
VLAN 800: [Management for switches/routers]
10.160.1.0/24

Hi
You will have the SVI on the core. Set a VTP domain, make one of the cores as VTP server and rest of the switches as VTP clients. Once you do this, you won't have to login into each switch and create a vlan locally. The vlans will be automatically advertised from the VTP server to all the VTP clients.
Thanks
Ankur
"Please rate the post if found useful"

Creating multiple vlans on a 877

Hi,
I want to create a default, voice and access vlan on a 877, but just one vlan comes up. On the other two vlan inetrfaces is the protocol down. I guess this has something to do with bridging. I've tried that already, but I can't find documentation about this. Can someone tell me how to bring up the other two vlan interfaces?

You need a trunk in case you are passing multiple VLANs on the port. However, in your configuration you do not need a trunk because each port is assigned to one VLAN.
IN order for all VLANs to go UP all you interface should be Physically and Porotcol UP. Check that all your Fast Ethernet Interfaces are UP.
Let me know how it goes,

Two VLAN`s on Small Business 200(8ports) and 500 (24ports)

Hello,
Im having troubles enabling two different VLANs on a locally static network.
The entire network is setup with only static ips and no DHCP server or router on this network. The network has just been handling fire units so a central station can watch if the fire units are online.
Now we want to establish a second VLAN on theese switches for other units like security on doors etc. Is this possieble without a router? The two vlans does not need to reach eachother.
I have checked many videoes online and such, but i dont seem to get the interface enabled to two different ip vlans at once.
I have managed to create different vlans, and assigning them to ports. But not defining two different ip subnets on the vlans.
I have also trouble setting the system clock permanently. Everytime i reboot the switch, it seems to be going back to factory, even thou. ive updated firmware to latest and also applied the changes.
Anyway, would much appreciate a answer regarding the vlan configuration.
Thanks
Thomas

Leo has given you some excellent advice ie. you cannot choose a kit list until you have a design. It just doesn't work the other way around. If you don't have the experience to design the solution then you can't really be choosing the kit. Otherwise when you do hire your consultant he might well be constrained by the kit already chosen and you will not get the best solution for your needs.
Please don't take any of this the wrong way. NetPro is a great forum for helping people out with technical and design issues with Cisco equipment but there are times when NetPro is not the best solution and this is one of them. We could each give you a kit list of what we "think" is the best solution but that really should come from the designer.
Jon
Leo - will you please stop losing your points oops, and now they are back again

After Enabling trunking and two VLANs on switchports - clients don't receive IP Addresses

Hello all and thanks for your help and expertise. Here's my scenario:
I have approximately 35 Ruckus APs in a building which has multiple VLANs. The switches are Cisco 3560G. I want to segment the wireless traffic onto a dedicated wireless VLAN (218). I created two scopes in DHCP to service the APs and wireless clients. The APs should get their IP addresses on VLAN 1 (VLAN 1 scope in dhcp.) The clients should get their IP addresses on VLAN 218 (VLAN 218 scope in dhcp). I utilized the following commands to accomplish this goal, unsuccessfully.
Example: on port gi0/5
1 - switchport trunk encapsulation dot1q
2 - switchport mode trunk
3 - switchport mode access
4 - switchport trunk allowed vlan 1,218
Problems: 1) The APs are not getting an IP address on the default or native VLAN 1 unless I configure an IP Helper. Please note we have another building where a consultant set this configuration up (and it works) but I don't see an IP helper set when I check the config for VLAN 1.
2) The wireless clients do not get an IP address on VLAN 218, even if I set an IP helper address. In the other building - there is an IP helper set on VLAN 218 so I'm not sure what I missing or if something else is configured.
I would greatly, greatly appreciate if someone could tell me what I'm missing here. Is there something else I have to do to ensure clients on vlan 1 and 218 are able to obtain dhcp addresses in the config of the switch? Do I have to further configure vlan 1 or 218? I'm enabling the correct encapsulation, trunking the ports, and setting the vlans. What am I missing here relative to APs and clients getting dhcp addresses. Anyway your help is much apprecaited.

You need vlan 218 on all switches and allowed on all trunks that need to pass traffic for that vlan.
You don't have to add it explicitly to STP as it should be run anyway but if you manually set STP priorities for other vlans you should probably do if for this vlan as well.
Shouldn't stop it working though.
If you manually assign a vlan 218 IP to a client can it ping the SVI IP ie. it's default gateway and if so can it ping devices in other vlans ?
Jon

I am a teacher that has 3 personal devices and then 8 I use at school. How can I create two differnt accounts?, I am a teacher that has 3 personal devices and then 8 I use at school. How can I create two differnt accounts?

I'm an elementary teacher that uses 9 of my ipad 2's at school and I personally have an iPhone, iPod, and iPad.
How do I keep the accounts separate? I tried to create two apple ID's, using my home and school e-mail, but that isn't working. I don't know how to
keep the two separate the two. Do I need to use a different name on the account?

ktuttle64 wrote:
I tried to create two apple ID's, using my home and school e-mail, but that isn't working.
It should work. That's how you do it.

I created two new albums in my photos on my iPhone. They do not show up on my ipad2. How do I get them on my iPad also

I Created two new albums in my photos. On my iPhone but they do not show up on my iPad.2. How do I get them to show up on my iPad also

Hello abaneki,
Thank you for using Apple Support Communities.
For more information, take a look at:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Have a nice day,
Mario

I want to use two separate Lion Time Machine backups and use them to create two separate profiles on one new computer

This is something I need to do temporarily but I must do it.
I have an iMac 27 (end of year 2009) I5. It has 1 TB internal and I want to replace it with a 2 TB internal.
I have time machine backups on an external hard drive that has been connected via Firewire.
I have another iMac (my son's)Imac 24 Intel Core 2 Duo that has it's own separate Time machine backup to it's own separate firewire connected external drive. Both machines are completely up to date with the latest version of Lion and all other necessary software updates.
When the internal hardrive is replaced - I want to use my latest time machine backup to create one profile on the imac and then use my son's latest time machine back up for a second profile. The end goal being to have everything from my current set up ie: apps, documents, itunes, etc existing in one profile and everything in my son's current set up existing in the other profile. We can both be administrators for the time being as well. I should note even though we both have some of the same apps, we both also have other apps that the other does not.
My profile will be using about 900 gigs of total space.
My son's profile will be using about 250 gigs of total space.
This is temporary until the new iMac is released. Then I will want to transfer my profile to that leaving my son's intact on the iMac 27 I5.
I realize that during the temporary period that Time Machine will be making backups of this entire two profile setup, which I am now understanding as I write this will create a new issue for me when I want to transfer only my profile to the new computer as well. But one bridge to cross at a time, I guess.
I need to do this because we must bring his current computer to my father - as his iMac G5 is inoperable. We have been doing this round robin hand me down in our family since IMac DV special edition :-)
Any insight on this would be greatly appreciated. And any other suggestions as well.
Thanks very much.

Hey Shootist000, Thanks for the replies. First off, I am actually okay if we both have each other applications so I am not concerned about that. It is still unclear from what you have said as to whether I can in fact, use these two separte time machine backup to create two separate profiles on the new hard drive. If that in fact can be done, then - will it create two copies of the apps we both have in the ROOT of the drive as well as placing all the ones we each have separately?
And reading your second reply, makes me think that maybe the partition is the way to go to begin with and then down the road - after I am in the new iMac, I could reformat the iMac 27 with only one partion and restore my son's latest back prior to the reformat thus giving him full access to the 2 TB of the drive.
If this is still making sense, does this mean :
replace the 1TB with a 2TB - but have it partitione - 1.5 TB & 500 GB.
Install(Restore using Time Machine) my latest back up prior to the 1.5 partition
Install (Restore using Time Machine) my son's latest back up prior to the 500 gig partition
Lastly, in order for us both to be using the partioned computer - I am assuming Switch user can no longer be used - so would we need to restart and select our respective partions in order to use the computer? And if so, how would we each be able to be using time machine to back up - two separte external hard drives - with each one dedicated to only one partition? Or ?
Thanks so much.
Ironically, I am only trying to do this so that I don't need to manually install all his apps, setting, games, blah blah for this temporary period. :-)

My wife and I decided to both buy Iphones do I put them both under the same apple ID, or do I create two different apple ID's and two differnt icloud accounts?

My wife and I decided to both buy Iphones do I put them both under the same apple ID, or do I create two different apple ID's and two differnt icloud accounts? We want to be able to share my itunes library on both our phones and sync our calendars, but I don't want every update and reminder that my wife puts in her phone and I know she doesn't want every reminder I put in my phone.

What you need to do is both use the same Apple ID for iTunes content, but separate Apple ID's for everything else. So, you keep your existing Apple ID. If not a verifiable email address, you will need to create a new Apple ID for yourself. You also create an Apple ID for your wife, again a verifiable email address. You use the existing Apple ID for all iTunes content. The new Apple ID's for iCloud, iMessage, FaceTime, etc. Here's how to create an Apple ID:
https://appleid.apple.com/cgi-bin/WebObjects/MyAppleId.woa/wa/createAppleId?loca lang=en_US
Use multiple devices on one computer:
http://support.apple.com/kb/HT1495

How to create two or more JVM in one machine ?

Hi to some background ,I want to invoke RMI call to a server ,and I have written the following client code ,that access a getCounter()to show the incremented static variables value ,each time calling the getCounter() will increment the static variable by 1.That code is deployed in the server.
PDOS_Remote_Interface service1 =(PDOS_Remote_Interface)Naming.lookup("rmi://x.xxx.xxx.xxx/REMOTE_SERVICE");
String s1= service1.sayHello();
int cont1 = service1.getCounter();
System.out.println(">>>>>> "+s1);
System.out.println(">>>>>> cont1 "+cont1);
PDOS_Remote_Interface service2 =(PDOS_Remote_Interface)Naming.lookup("rmi://y.yyy.yyy.yyy/REMOTE_SERVICE");
String s2= service2.sayHello();
int cont2 = service2.getCounter();
System.out.println(">>>>>> "+s2);
System.out.println(">>>>>> cont2 "+cont2);
This is working fine with even two different server (I mean in two physically different machine(x ip and y ip) ,there ip are different )
with following output :
Server Says Hai!
cont1 0
Server Says Hai!
cont2 0that is static variable is not shareing as they are in two different server
Now My problem:
I want to hit the one and only server ,In this case Service1 and Service2 are getting the remote instance from only one machine .And when I am doing that I am getting the static variable incremented ,That is following output
Server Says Hai!
cont1 0
Server Says Hai!
cont2 1Is this possible to create two JVM instance in a particular machine ..??
I mean I want the first output (both static variable shows 0)in second implementetion (using only one machine )???

Yes, but the naming service is only going to accept one registration for a given name.

My boyfriend and I have our own iPhones but share an iPad. How do we create two different profiles or user accounts, etc?

My boyfriend and I have our own iPhones but share an iPad. How do we create two different profiles or user accounts, etc?

Unfortunately, at the moment you cannot create two user profiles on one iOS device.

I have a new iMac and i created two libraries on iTunes. how do i copy songs from one library to the other?

I have a new imac. I created two libraries, one for me, one for my kids. how do I copy songs from one library to the other library?

Not easy unless you're just content with adding some files to the other as new files but lose playlists for those files, and playcount, and ratings, etc. If you're okay with that, you can drag the media folder from one library to the other. If you use default settings and want to duplicate the media, just drag it. If you want to add the media but leave it where it is currently located, hold down the option key while dragging to the library window.
Otherwise:
PowerTunes - http://www.fatcatsoftware.com/powertunes/ (commercial software)
syncOtunes - http://homepage.mac.com/oligrob/syncOtunes/syncOtunes.html

Creating two vlan in AP 1131

Similar Messages

Maybe you are looking for