Creating wired/wireless network with Airport Express

I've just bought a MacBook, with it I bought an Airport Express.
I have a PC desktop that has a wired ADSL connection.
In the Mac store I was told that I could connect my ADSL modem to my Airport Express and then connect wirelessly from my PC and from my Mac.
I've just got home to discover that my modem connects to my PC with a USB port. I also don't seem to have wireless connectivity on my PC.
So my quesitons are:
1) Do I simply need to buy an ethernet cable to connect my modem to the Airport?
2) Will a wireless dongle, in the back of the PC do the job of giving me a wireless connection, if so, how much does it impede speed?
3) Is there anything I haven't thought about?
Thanks v much
Macbook

Thanks to Parker in particular on this.
The problem is now solved, but only after I went and bought a netgear wireless/router/modem.
As a consequence my previous wired USB connected modem is obsolete, as it seems is my AirportExpress.
Therefore my setup is that the desktop is wired into the router through an ethernet cable. The MacBook is picking up the wireless signal.
So far, it seems to be working satisfactorily.
thanks again

Similar Messages

HT1515 Creating An wireless network with airport express

HI, I want to create second network for children on the second floor, i understand i should connect my existing router to an aiport express using the cable, but witch airport express slot should i use (wan or lan)?

WAN "O" port

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

By creating wireless network with Airport Express, original wireless network stops functioning

I want to use the Airport Express to create a second wireless network downstairs. Upstairs I already have a wireless modem/router (Draytek 2850). The signal downstairs however is to weak. When I create the wireless network on the Airport Express, this works perfectly. However after the creation, the wireless part of the Draytek modem/router stops functioning. The wired part keeps working, but when I connect to the wireless part I access anything. Why is that?
The Express is set to Bridge modus and under TCP/IP I've selected that the IPV4 configurations has to go via DHCP.

I set the Network Name the same as the SSID, security type on the router is Mixed(WPA/WPA2)/PSK, which on the AX is WPA/WPA2 - personal I guess. The password is the same as the DrayTek.
Yes, WPA/WPA2 Personal on the AX is the same as the Draytek's wireless security option.
The radio channel of the Draytek router is 6, the channel of the AX is 11. Do I miss anything here?
No, it looks like you have all of the right settings as far as I can tell ... and you already stated that the AX is in bridge mode, i.e., Connection Sharing = Off (Bridge Mode) ... correct?
If so, I would recommend performing a complete power recycle of your networking components, as follows:
Power-down the DrayTek, and AX. Order is not critical.
Power-up the DrayTek; wait at least 10-15 minutes to allow it to stablize.
Before powering-up the AX, verify that you can gain Internet access via a wireless connection to the DrayTek. If so, continue.
Power-up (plug-in) the AX; wait at least 5-10 minutes to allow it to stablize. It should have a steady green status light. If not, use the AirPort Utility to determine the reasons why it doesn't from the Status page of the Utility.

Establishing a wireless network with airport express

Can someone please help me setting up a wireless network?
I'm using netgear DG834GT and want to set up a wireless network with my airport express. Unfortunately i cannot set it up and need someone to help.
Thank You

If you want to configure an Airport Express to work with the existing wireless network created by your DG834GT wireless router, then follow the advice posted here by David Lovel (the advice is applicable to both Mac and PC users):
David Lovell, "Airtunes for XP with a Wired/Wireless network" #1, 09:05pm Jan 8, 2005 CDT
I hope you really did mean to say you were using an Airport Express. Don't confuse an Airport Express with an Airport Extreme card - the Airport Extreme card is the name of the wireless adapter built into your Powerbook.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

Extending Gen 1 Time Capsule Wireless network with Airport Express N

I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
My setup is as follows:
Time Capsule is connected to Cable modem with the following wireless settings:
Wireless mode -> Create a Wireless Network
Allow this network to be extended -> Checked
Radio Mode ->802.11n (5Ghz N only)
Wireless Security -> WPA2 Personal
The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
Wireless Mode -> Extend a Network
Select the Time Capsule Network
Allow wireless clients -> Checked
Wireless Security -> WPA2 Personal
However after I reset the AE the LED glows Amber and the following problem is reported:
+Wireless Network+
+This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
When I check the Airport->Wireless tab the settings were as before.
Any thoughts on this? Thanks.

Welcome to the discussions!
Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
If so, then move it back another 10-15 feet, etc.
5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
Message was edited by: Bob Timmons

Extending Wireless Network with Airport Express / DLink Wireless

I have a DLink wireless router WBR-1310. I own two Airport Express 802.11n's. Can anyone help me out with how I can properly set-up an extended network with these products? All help is greatly appreciated.

You would need one AirPort Express located near the D-Link router and connected to the D-Link with an ethernet cable. This Express would be configured to "create a wireless network" and "allow this network to be extended"
If you have two areas that need more wireless coverage, you would locate an AirPort Express approximately 1/2 the distance between the "main" AirPort Express and the area that needs more wireless coverage.
Then do the same with the second area that needs more coverage.
Without knowing your room layout, I can't honestly tell you whether you need only one "extending" Express or more than that.
It will help to remember that the "extend" setup works like the hub and spokes of a wheel. Your "main" Express connected to the D-Link would be the "hub". Each of the "extending" Express devices would be at the end of a spoke. The Express devices at the ends of the spokes communicate directly to the hub, not to another Express at the end of another spoke.
So, to work well, hopefully your D-Link router and Express will be located in a central area of your home so the extending devices will work around the perimeter.
I would recommend that you study Apple's support document on extending wireless networks before you make a final decision on what to do.
http://support.apple.com/kb/HT4145
Finally, consider if you can connect the two Express devices you have now back to the D-Link using ethernet cables. This would provide much better performance than a wireless only situation.

Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

Expanding wireless network with Airport Express but without Airport Extreme

Hey guys,
I was wondering if I can expand my wireless network with my Airport Express without Airport Extreme base station. I have a Netgear wireless router. Is it possible? Can you give me tips on how to set it up?
Thanks a lot!
Marc

marcribeiro, Welcome to the discussion area!
No that is not possible. The Netgear is not compatible with Apple's WDS.

How to create a wifi network with airport express in hotel room?

When I'm traveling to hotels that have internet, but not wifi, how do I set up a network using airport express? When I've done this at home, I've used my laptop with the airport utility. Can I do it with just an iPad?

Yes, you can use the Airport Utility for iPad here:
https://itunes.apple.com/us/app/airport-utility/id427276530?mt=8

Extend Wireless network with Airport Express via Cat6 cable to Cisco E4200 router.

Hello there! Totally new to this, but I've been doing a lot of research, and have been getting conflicting answers, so maybe someone can help me out. I've been reading that you cannot wirelessly extend your network unless you have a time capsule or an airport extreme. However on some forms, if you have the airport express hard wired to the router(in my case a Cisco E4200), you should be able to extend your network. Is this accurate? If so, can someone please post steps on how to do this? Thanks!

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

Joining an existing wireless network with airport express

Ok, am almost to the point of throwing my AX across the room
AM trying to join an existing wireless network, its from a 2Wire gateway
one of three things happen
it won't find the AX in the first place
it recognizes it, but i can't connect to it
it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
it doesn't show up in my available wireless networks at all
protected via WEP, and i have tried using all the security options.

The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
Are you using MAC address access control in addition to WEP?
Turn off WEP and see if that makes a difference?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WEP is now considered not to be secure and therefore it is advised you use WPA.
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

Extending Sky Wireless Network with Airport Express.

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Does anybody know if this is possible and if so, can they please advise me how I do this. (I am using Windows 7 on my Dell laptop)

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Unfortunately, the salesman may not have understood your question, or he may have given you incorrect information.
It's possible to have the AirPort Express provide more wireless coverage if you connect it using an ethernet cable permanently to your Sky router.
But, the AirPort Express cannot "extend" the wireless network produced by the Sky by connecting using wireless only. The "extend" feature will only work if you have an Apple to Apple wireless connection. This feature is not compatible with the products of other manufacturers.

Extending Snow wireless network with AirPort Express

I am trying to extend my existing Snow network with an AirPort Express, which I will connect to the Snow (through an unmanaged ethernet switch) via an ethernet cable. I think I know how to do this but if anyone has any hints, they would be appreciated.
In addition to using the AE as an "extender/wireless access point," can I also configure the system to stream AirTunes to the AE through the ethernet cable at the same time?
Thanks

Oops, sorry I misread your post. That should work. Make sure that you disable the "Distribute IP addresses" option on the AX so that it acts like a wireless access point. On the AX, just enable the "Enable AirTunes over the Ethernet port" option on the Music tab.

Creating wired/wireless network with Airport Express

Similar Messages

Maybe you are looking for