Creation of Daily Inspection Lots

Dear Experts,
   I am new to this area. I have a req.
Against a particular PO we will be receiving 50 to 100 truck deliveries. For each delivey we will be doing inspection i.e daily.
By the end of the month we enter the average value for the whole month in SAP. Because of this we will not be able to take full report from SAP and distribute to Production Section. We are still doing this activity in excel.
Kindly let any one explain on how to do this activity ona daily basis in SAP.
thanks

You can have various ways to do it.
1.Create a material in SAP
2.activate QM view for this material & activate 01 inspection type.
3.for each PO as you said you have 50 to 100 deliveries.So whenever you get receipt (migo) ,Inepction lot will be get created for 01 inspection type.
4.lot size will be equal to Goods receipt size.
5.Take Usage decision for the material in sap through QA32.
6.At month end you can run report QA32/QA33 for getting the total receipt.
7.You can use reports like
   MCXC : Material Analysis (Month wise)
   MCXI : Material analysis
I hope this will help as this can be one of the way..........

Similar Messages

  • Auto creation of calibration inspection lot thru maint. planning/scheduling

    Hi
    I have to schedule calibration inspection of a few equipments in such a way that system automatically create inspection lot & calibration order daily.
    Whether user enter calibration result or not, inspection lots in future should be created automaticallly.
    I created a single cycle plan using IP41 and start the schedule using IP10, the system created first inspection lot automaticaly but always require me go to to scheduling and save the plan again if I want to create next inspection lots. How can I configure/set the system in such a way that it creates inspection lots/calibration order automaticaly
    Plz also tell after taking usage decision of inspection lot whether I need to do some act on calibration order such as technical completion or business completion.
    Thanks in advance
    Edited by: Chris SAP on Jul 5, 2010 9:56 AM

    HI Chris,
    During calibration order  creation only inspection lots are generated.
    Manual order creation
    Run Tcode IP30 deadline monitoring to create order if it is due date the order will be generated with inspection lot.
    Automatic order creation
    Create a batch program to run IP30  daily giving inputs needed so that the order will be generated daily.
    Usage decision is completion of inspection lot
    Technical completion and business completion is for order completion. Technical completion is needed to schedule the job correctly.
    Regards,
    Alagesan M

  • Creation Equipment Trigget Inspection Lot

    My customer Need to start the cycle with Creation of equipment and trigger inspection lot automatically contains the number and details of the equipment how can we do this?

    How to create Inspection lot for Equipment without task list & order for the Equipment??
    No inspection lot could be generated for order
    Message no. IW217
    Diagnosis
    An inspection type has been defined for the order type in question. An inspection lot should be generated when the order is released. No inspection point field combination has been defined in any of the maintenance task lists used in the order. This is why no insepction lot can be generated.
    Procedure
    If an inspection lot is to be created, the order must contain at least one procedure which was taken from a maintenance task list and which has been define for one of the inspection point field combinations. This must be done before the order is released.
    This is the information message you will get while releasing the order without task list or with task list which is not having inspection point.

  • Creation of Recurring Inspection Lots with Serial numbers

    Hello,
    We have the following scenario at our client :
    <i>MIGO_GR</i> is used to create GR for materials with Serial number requirement. The serial numbers can be generated automatically or manually entered on the screen. At this point of time, the Shelf Life expiry date & Next Inspection date are calculated based upon the Production date. The Batch gets created with Next Inspection date, Inspection Lots are created and the Serial numbers are assigned by the system. The stock moves into QI.
    The stock is moved from Quality restricted to Unrestricted stock via <i>QA11</i>. The serial numbers are handled by the system or can be managed on screen.
    Transaction <i>QA07</i> (Deadline Monitoring of Batches) is used to create Recurring Inspection. QA07 gives error message IO304 that "<b>Only 0 serial numbers entered instead of 1</b>". The problem is that system doesn't pick up the corresponding serial numbers.
    OSS # <u>497845</u> mentions that Transaction QA07 can not handle serial number. The serial numbers are very critical to the business process.
    Has anyone come across this situation before ? Please suggest solution or workaround. I tried using BAdI "<b>INSPECTIONLOT_UPDATE</b>" & was able to create Inspection Lots with serial number assignment, also manipulated Batch to change the Next Inspection date. The problem is Material Movement (322) Document does NOT get created.
    Also tried implementing BAdI as per OSS # <u>608830</u> but doesn't give desired results.
    Any help is greatly appreciated.
    Best Regards,
    Homiar Kalwachwala.

    Hello all,
    Just wanted to bring this on top to be noticed.
    Would appreciate any help, suggestions...
    Regards,
    Homiar.

  • Creation of one inspection lot for more than 1physical sample

    hello SAP,
    we have one common question.I have created 3 physical sample 20000006,2000007,2000008 and now i want to create one inspection lot for these 3 physical sample through QPR5 Transaction but system is generating each inspection lot for each physical sample which is wrong process. this is common scenario for most of the industry.SO please clarify and provide the solution

    Hi,
    I hope this solution gives some way out for you to solve your problem . I assume the sample is for  the same material , phy. sample type and category
    Create a new physical-sample drawing with refernce to :
    Using this function, you can create a new physical-sample drawing (with one or more physical samples) that references:
    An inspection lot
    A production order or process order
    A production version
    You use this function to create physical samples that have not been planned in a sample-drawing procedure and which you can draw from a production process according to your specific needs. In an inspection during production, for example, you can draw physical samples from the process on the basis of time or quantity (for example, a physical sample every three hours or for every 1000 liters of material produced). You can freely specify the inspection-relevant operations in which you want to inspect the physical samples for the new physical-sample drawing.
    please do let us know wether you were able to create one inspection lot .Or else please ellaborate the question step wise t-code and functions Will try to find a solution .
    cheers
    kp
    source of information : SAP

  • Inspection lot creation after receipt of certain quantities?

    Gurus,
    My user requires the creation of an inspection lot of 1 piece after the receipt of 200 pcs in stock as a kind of audit. This is not a goods receipt feom production as it will be done for each piece. .but was is needed is an event to create a lot woth piece for after receiving 200 pcs ( these receipts most provably will be on different days & in different material documents)
    Can I apply this requirement through sap standard or user exit ar abap?
    Thanks in advance,

    Hi,
    Rephrasing it,
    each piece will be assigned to a batch in a one to one relationship
    One piece represent one batch, Correct? And when GR is done against production for this batch, you get an inspection lot. QA personal do the inspection and material moves to Unrestricted stock.
    Beside, the goods receipt from production that will be performed as mentioned, the user may re-inspect one piece already present in the unrestricted use as a kind of audit. the user wants this auditing lot to be generated automatically for every 200 pieces instead of creating it manually.
    After the initial inspection is over and material is lying into Unrestricted, user would again inspect each of them and need automatic creation of inspection for every 200th piece/ batch. Correct?
    Is this what you are looking for?
    If that is the case, I don't think automatic lots can be created since there is no movement involved. User is simply doing retesting but nothing in system then how would SAP understand that an inspection lot is required?
    Even if some development is done to generate an inspection lot for every 200th batch received into Unrestricted, you would still need an inspection type to be activated against the material and some movement to be triggered.
    ntn

  • Avoid creation of Inspection Lot by MIGO

    Hi All,
    In some cases I want to avoid the creation of an Inspection Lot, It can be done by configuration.
    How can I do that?.
    I was thinking to change the "Status GR Doc." but In the badi MB_MIGO_BADI that field can by changed.
    Please any help??

    Hi,
    Check tcode OMJJ. Set a movement, and go to 'deactivete QM inspection..' and change the flag 'QM not active'. Read the documentation and the help on F1.
    I hope this helps you
    Regards,
    Eduardo

  • Source inspection - inspection lot skip for certified vendor

    Hii,
    I have a requirement in which during source inspection, the inspection lot should not be created if the Vendor is certifed. I have made the following settings:-
    1. In Vendor Master, maintained the Actual QM system in control-reference data.(QM system marked for skip in customizing)
    2. In Material Master-
        - Activated QM Proc- QM control Key -Delivery release
        - Target QM system
        - Inspection type for source inspection activated in inspection set up
    3.In Quality Info Record for Vendor,Material,Plant combination-in Inspection Control tab-
        - Maintained the existing QM system & validity
        - Selected 'No Inspection' in Insp. control
        In Vendor source inspection tab maintained the inspection type & lead time.
    Inspite of the above settings, I can see this PO (for vendor,material,plant) in the source inspection worklist(QI07).
    Please suggest as to which setting I might be missing.
    Thanks!!!
    Regards,
    SV

    Hi,,
    You have to go T code QI07
    where give input Vendor ,Material plant,
    Delivery dateopening peroid
    Then execute the transaction .
    Select line item click oninsp lot & save.
    Where you have trigger lot for the same then only lot will get genarated.
    Regards
    SANIL
    This confugaration required if you have option if lots get rejected.
    Quality management-QM logistics-QM procurement -Control key
    Define control key;
    GR/Source inspection control;
    GR for rejection; three option is available
    1.source inspection has no effect on goods receipt
    2.Creation of new inspection  lot
    3.Goods receipt not allowed
    Regards
    SANIL
    Edited by: Sanil Vadke on Mar 12, 2010 7:29 AM

  • QM- HOW TO RELEASE INSPECTION LOT

    HI GURUS.
    I HAVE A PROBLEM,PLEASE HELP ME OUT;
    GURUS, I WANT TO KNOW THAT HOW CAN I RELEASE THE INSPECTION LOT; SO THAT I CAN TRANSFER THAT QUANTITY FROM  QA TO UNRESTRICTED USED;
    PIYUSH SINGH

    First things first.
    The inspection lot when created takes the default values from the material master setting like whether the inspection is to be triggered.
    Once the inspection lot is created and after you change the material master or info records then it will not be refected in the inspection lot.
    So important thing is to get the state of quality system when the inspection lot was created to solve the problem.
    Go the transaction code [QA02] and see the requirements in the inspection specifications tab whether the Task List/ Specification button is enabled or not. If it is enabled means characteristics are not yet assigned. Press the button. If it dosnt work by pressing, it means no corresponding task list or material characteristic as specified in the materail master - Quality management Screen - Corresponding inspection type values. Even if you make changes now it wont be reflected in the lot. So get the settings at the time of creation of the inspection lot. And create the required task list [QP01] or material specification [QS61]. If already the task list / material specification button in disabled means the characteristics are picked.
    Now goto transaction [QE51N] and specify your plant and material and generate the list of open lots
    Select your lot and record the characteristics
    Not you need to valuate and close each characteristic.
    Save the data and come out of the trasaction after all the characteristics are recorded.
    Proceed to TCODE QA11
    Take a usage decision, save the data and quit the transaction.
    Now check whether the lot status is changed or not
    Please tell me if it dosnt work

  • Enhancement for QA01 (Inspection Lot)

    For creation of new inspection lot via QA01; upon saving, user wants to disable printing of the inspection lot form (sapscript using standard print program 'RQEEAS20') when the system status 'QALS-KZSKIPLOT' = 'X'. May I know how should I go about to start? (if user exit? which user exit?)

    Hello,
    Here i suggest you that if you are using Exit for UD then in that only just apply one code where program first will check the QAMR/QASR etc. all result table field w.r.t inspection lot and if fields found empty means no data or RR then system wont pass UD code for UD posting.
    Or just make first MIC as required MIC and apply the code in that first MIC, if that MIC value is blank then again system wont allo UD.
    Secondly, Status profile maintenance is also an another stdn way to execute the requirement.
    Regards

  • Outbound trigerring for Inspection Lots

    Hi Friends,
    I am working on QM. I have to trigger inspection lots data in the form of an outbound idoc. I need to find out any creation/change in inspection lots data.
    In this scenario the inspection lots will be created/changed when:
    1) there is a creation/change (QA01, 02)
    2) Production orders are released (CO02, 05)
    3) GR done (MIGO), stock posted in QI.
    Has anyone worked on such a requirement earlier? Any suggestions on flow-logic for picking up the inspection lots data in a custom wrapper program?
    Thanks in Advance...
    Birendra Chatterjee

    Hi,
    you should be able to create inspection lots when executing                 
    BAPI_GOODSMVT_CREATE. See for example the attached note 536769 that         
    is about wrong status in the inspection lot created in this way.                                                                               
    Please review your data used for testing this BAPI. 
    Best Regards,
    Arminda Jack

  • Inspection lot number not recorded in production order

    Experts,
    when I release a production order, the inspection lot is created correctly (type 04 - early lot creation) but the inspection lot number is not recorded in the production order. Why not?
    Rgds

    Dear,
    Only 03 type will be recorded in header, not 04. It is normal

  • How can I generate automatic inspection lots every 15th day

    Hello,
    My client receives chemicals (Raw Mat) every day. Incoming inspn is done only for physical spec and Usage deciison is taken on same day itself.
    As he is getting raw mat from good vendors, he usally do chemical analysis every 15th day.
    Whats the best way for me to map this process of generating inspection lot on every 15 day. initial incoming lot we cant use as he already taken UD on that.
    15 day chemical analysis dont have any impact on qty posting as Raw mat usally will be consumed.
    Is there anything other than manual lot. I welcome all ideas.

    In this case your looking at a pooled sample of the approx. 15 batches of material that were received in.  Correct?
    If you are batch managed, then no.  Since the sample is a composite sample, you can't link it to anything else really and you don't have a batch number to enter into the inspection lot upon creation.  First, you'd have to create a dummy batch to hold the results.  Which you could do maybe by date if your system allows external batch numbering.
    Then you could at least manually create the inspection lot.
    The is no true "event" to trigger the creation of the inspection lot as there is when you do a GR.  The only why you could trick the system would be if your were willing to maintain a separate storage location, and do a stock posting to it of the sample quantity each day.  Then you could have an inspection plan that would create a skip lot each day.  On the 15th day it would become required.  You would probably utilize a copy of movement type 411 for this and use that custom one to make the moves. 
    The problem with this is then you'll have to write off that little bit of material at some point for accounting purposes.
    Another option.. you could create dummy batch and set a 15 day inspection interval on it.  Use deadline mointoring to create the lot one day in advance of expiration.
    One more option:  Use standard calibration inspection to set up a calibration program.. I.e. recalibate every 15 days.
    Craig
    Edited by: Craig Snyder on Mar 25, 2008 1:08 PM

  • Inspection lot creation

    Dear Experts,
    Reqiurement as follow :
    We have four plant like 1000,1001,1002,1003,1004
    System creates inspection lot when we do GRN against in stock transfer PO when STO from
    1000 to 1004, 1001 to 1004, 1002 to 1004, 1003 to 1004, as we have activated inspection type 08,01 in MMR.
    My requirement is system should not create inspection lot when STO from 1003 to 1004 only.
    We can not deactivate inspection type as we need inspection lot when STO from other plant.
    Please help in this scenario.

    In QM, we can deactivate the quality for certain movement type.That means though QM is active in material master, if we are using any movement type for which QM is not active, it will not generate the inspection lot. For STO from plant 1003 to 1004, use the movement other 101 i.e copy of 101.
    Copy 101 movement say as 901.Using following path deactivate QM for this new movement type 901.
    SPRO - QM - Q. Insp - Insp lot creation - Insp for goods movement - Deactivate insp for movement type. Select the indicator "QM not active".
    Now use movement type 901 for STO from plant 1003 to 1004.
    Vishal Jonnalwar

  • Change of Inspection Lot Specifications at the time of lot creation

    Hi,
    We are using In-process inspeciton.
    At the time of Production Order release an Inspection Lot is created automatically.
    We want the Lot Specification values to be changed based up on the Configuration of the Sales Order.
    Is there any User Exit or BADI  that can be used for this purpose?
    Ramakanth

    Hii,
    Lot specifcation values cannot be changed once inspection lot is created. If u know specification only after creation of inspection lot then u include unplanned inspection charcteristics. Here u can define spec after lot creation also.
    with regards,
    K.Lokesh.

Maybe you are looking for