Creation of export datasource failed

Hi All.
i copied a bussiness content data source object (DSO) and tried to activate it. it is giving error that
"The creation of the export DataSource failed"
Why ??? where m i going wrong.
Thanks & Regards,
Mo

Hello,
     This is the problem becos the system is unable to create DATAMART for DSO object.  The following reasons might be hindering the creation of DSO.  Please check whether
1)  You have proper authorization to create Datasource/Datamarts.
2)  If so then, check whether DATAMART for the BW Self Source System is properly Installed from Business Content.  (I hope you are working on the version 3.5 or later.. here we need to manually install Aplication Component related to Datamart from Business Content so that Datamart creation never fails after that)
3)  Also check BW Self Source System is properly functioning.
Thanks
Kishore Kusupati
Edited by: Kishore Kumar K on Jul 28, 2008 5:35 AM

Similar Messages

  • The creation of export datasource failed.

    Hi everyone! This is Chong Tao from Central Michigan University and I got one problem recently when I was doing my set-up of the BW course. I actually wanna copy the infocube but when I click the "Generate export datasource", it automatically comes up one error message "The creation of export Datasource failed". What should I do to overcome this problem? Thanks for paying attention to this problem and I need your valuable advice as soon as possible since it is for the student in this SAP BW course.

    Hi,
    I guess your objective is to copy an existing infocube. Right ?
    In that case, Right Click Infocube and use 'copy'. This will create another Infocube with the same structure, but with no data. You can then fill this copy Infocube by cerating transformation between the two infocubes and scheduling through DTP.
    'Generate export datasource'  can normally be done when there are two separate BW systems and you want an Infocube to be a source of data to another Infocube in a different BW system( though it can be used in the same BW system as well).
    Best Regards

  • The Creation of Export DataSource Failed Error while transporting ODS Cube

    Hi  All,
    I am facing this issue from last 1 week.. i had developed an ODS cube in APO-DP BW which will fetch data from SAP R/3 and its working fine in APO Dev Server.  But when i transport this cube into APO PAC(Prodn Server) the below error i am getting..
       Start of the after-import method RS_ODSO_AFTER_IMPORT for object type(s) ODSO (Activation Mode)
       The creation of the export DataSource failed
       Password logon no longer possible - too many failed attempts
       Password logon no longer possible - too many failed attempts
       Error when creating the export DataSource and dependent Objects
       Error when activating DataStore Object ZANAUTSL
    I also updated the transport conversion tables but still problem not resolved.
    Immediate help is hightly appreciated.
    Thanx
    AJ

    Hi AJ,
    Looking at your error, it seems that the RFC user's password is locked and hence connectivity from R/3 towards APO BW is broken.
    You know the name of your export datasource (from R/3 to APO BW). Find out the name of your R/3 source system e.g. PACCLT000, by scrolling to the right against teh export data source.
    Take help of your Basis or EAI team to identify the RFC destination corresponding to the connectivity from the R/3 source system (PACCLT000) to your APO BW system. (If needed ask for help from your BW team, I am not very sure how connectivity would be set up from R/3 to APO BW, I guess this would be independent from CIF connectivity)
    For this RFC connection from R/3 to APO BW, see which RFC user is maintained in SM59 in APO and ask your security team to reset (or unlock) the password of this RFC user in R/3, and then if required update the user password details in SM59 in APO also.
    After this, your issue should get resolved.
    Thanks - Pawan

  • DSO activation failed due to creation of the export datasource failed

    hi experts,
    i am activating DSO, but failed. Cause is "The creation of the export DataSource failed"
    there are many threads in the forum saying restoring the BI myself source system can address it, I tried many times, but failed.
    I used program RSDG_ODSO_ACTIVATE to activate an already activated DSO, it returned same error and the original activated DSO turned into inactivated. So I guess there must be something wrong with the setting.
    please advise, thanks!
    attach error info:
    The creation of the export DataSource failed
    Message no. RSBM035
    Diagnosis
    The system could not create DataSource .
    System Response
    The metadata for a DataSource must be created while the export InfoSouce is being generated. An error occurred at that time.
    Procedure
    Consult the appropriate developer (function module: RSA1_OLTPSOURCE_GENERATE).
    The delta process ODS does not exist
    Error when creating the export DataSource and dependent Objects
    Error when activating DataStore Object ZFIM_D09

    Hi,
    As I read the system RESTORE option should resolve your issue. From RSA1 try to restore your source system and try to active your DSO again.
    Regards,
    Durgesh.

  • Transport Error-The creation of the export DataSource failed

    Hi Experts,
    I am transporting a DSO from DEV to QA in 7.0 system.While transporting the DSo i am getting the below mentioned error.
    The creation of the export DataSource failed
    Reading the Metadata of APMD0009 ...
    Creating DataSource 8APMD0009 ...
    Password logon no longer possible - too many failed attempts
    Password logon no longer possible - too many failed attempts
    Error when creating the export DataSource and dependent Objects
    Error when activating DataStore Object APMD0009
    the request conatins just the DSO and not the Export datsource.i have also tried exporting both together still it failed.
    I have referred OSS note No.597326 for the same.But it didnt helped in resolving the issue.
    Has any one come across this kind of an issue.
    Thanks in advance!!!!!
    Regards,
    Umesh.

    No it didnt seem to work still got the same password error..                                                                               
    Start of the after-import method RS_ODSO_AFTER_IMPORT for object type(s) ODSO (Activation Mode)              
    /     The creation of the export DataSource failed                                                                 
          Name or password is incorrect (repeat lo gon)                                                                
          Name or password is incorrect (repeat lo gon)                                                                
          Error when creating the export DataSource and dependent Objects                                              
          Error when activating DataStore Object 0BBP_BID                                                              
    /     The creation of the export DataSource failed                                                                 
          Name or password is incorrect (repeat lo gon)                                                                
          Name or password is incorrect (repeat lo gon)                                                                
          Error when creating the export DataSource and dependent Objects                                              
          Error when activating DataStore Object 0BBP_QUO                                                              
    /     The creation of the export DataSource failed                                                                 
          User not authorized. Session terminated                                                                      
          User not authorized. Session terminated                                                                      
          Error when creating the export DataSource and dependent Objects                                              
          Error when activating DataStore Object 0PUR_DS03                                                             
    /     The creation of the export DataSource failed                                                                 
          Name or password is incorrect (repeat lo gon)                                                                
          Name or password is incorrect (repeat lo gon)

  • The creation of the export DataSource failed 0FIGL_O06, 0FIGL_O02

    Hello Expert,
    I have an issue with the export data source creation,
    This is the detail,
    Thank you very much in advance for your kind help,
    The creation of the export DataSource failed
    Message no. RSBM035
    Diagnosis
    The creation of the DataSource &v1& was unsuccessful.
    System Response
    Whilst generating the export InfoSource, the metadata for a DataSource must be generated. An error arose when doing this.
    Procedure
    Consult the appropriate developer (function module: RSB1_OLTPSOURCE_GENERATE).

    Niurka,
    Is this datasource for a hierarchy? See if note - 403092 is relevant.
    Viren

  • The creation of the export DataSource failed

    Dear All,
    Can u give me the some information to fix the following error which i got while moving Multicube from Dev sys to Prod. sys. multi cube consits of lot of ODS object as dependent objects.
    Error FYI.
    The creation of the export DataSource failed
    RFC connection to source system PBWCLNT300 is damaged ==> no Metadata upload
    RFC connection to source system PBWCLNT300 is damaged ==> no Metadata upload
    Error when creating the export DataSource and dependent Objects
    Error when activating ODS Object 0CRM_CN2P
    Regards,
    Veeru.

    Hi Srinivas,
    If itz SS problem i can able to transport the other objects like cubes, Info Obj.. etc. only while transporting the ODS obj it is showing
    can u help me on this.
    any way i wil chk with basis team and ask to reset PWD.
    Regards,
    Veeru.

  • ODS activation error( The creation of the export DataSource failed

    Hi Friends,
             i have a problem activating the ODS. after defining the ODS, when i try to activate the following error is occured
    1.The creation of the export DataSource failed
    2.RFC connection to source system BWD100 is damaged ==> no Metadata upload
    3.Error when creating the export DataSource and dependent Objects     
    Any help would be appreciated
    Thanks

    Seems that there are one or more characteristics in the ODS for which one or more attributes may be new or inactive.
    Please see SAP Note 597326..Pasting the content below..Solution steps are also given..
    Symptom
    When you activate or transport ODS objects, the following errors appear in the log:
    "The creation of the export DataSource failed". Message number RSBM 035
    "Error &1 in function module &2". Message number RSBM 006
    "Error when creating the export DataSource and dependent Objects". Message number RSDODSO 169
    "Error when activating the ODS object &1". Message number RSDODSO 168
    Other terms
    RSBM 035, RSBM 006, RSDODSO 169, RSDODSO 168
    Reason and Prerequisites
    A characteristic involved is active but it is using new or inactive attributes.
    Characteristics involved are all characteristics used in the ODS object.
    Solution
    Check all characteristics involved as described in the following:
    Check the Compounding and Attributes tabs in the characteristics maintenance.
    All characteristics here must be active. This is displayed by a green icon.
    If this is not the case for a characteristic involved (a gray icon is displayed on one of the two tabs), activate the characteristic involved. This also activates the inactive dependent characteristics.
    After you have checked and repaired all the characteristics involved as described above, the loading/maintenance of master data should work again.
    cheers,
    Vishvesh

  • Export DATASOURCE failing

    I removed a IO from ODS, This ODS feeds a CUBE
    The transport of ods/avtivation/transfer are successful along with the update rule for cube.
    However the generate of EXPORT datasource for ODS [ from ODS to Cube]is failing with the message DUMP -
    The termination occurred in the ABAP program "SAPLRSAC" in"RSAR_TRANSTRUCTURE_ACTIVATE".
    The comments in failed src code reads like                        
    *if generated ODS InfoSource,                         
    no PSA versioning possible                           
    This is not allowing me to do an init of ODS!
    When i do an INIT I get the followign message -
    There is no PSA for InfoSource '8ZODS' and source system 'QUALITYSYS'
    I tried the reimport ,now the reimport failed with a dump
    Any suggestion and help is appreciated

    I have gone thru the SE38-RSSGPCLA/TRASACTALL but still my 8Zods datasource is not active and its PSA is not active.
    When I do the init for the ODS its says 8zods has no PSA, so I try to generatre export datasource for ODS[which is inactive after trasport] i get a short dump as posted above.
    The change log and theold request[active] are deleted for ODS, BUT the requests do not go away from ODS-manage screen!!
    QUALITYSYS is a copy of PROD and is 3 months back, also we have done many changes to the ods and other datamart kind ods in this landscape after the syscopy.
    Thanks fro all your replies.

  • Generate Export Datasource

    Hi All,
    While activating an ODS object, I got the error “The creation of the export datasource failed”. I tried activating the entire source system and replicated it. But still I am facing this issue. I checked the ODS in RSRV also. There it gave me the error “Number of rows for active program and temporary program are different". I am facing this issue for newly created ODS objects also.
    Can someone throw some light on this?
    Thanks in advance,
    Febina

    Hi Febina Mohanan
    Welcome to the board..
    There are few considerations with your issue
    1)Occured Because of Space issue Just check the space statistics in DB02 with the help of BASIS
    2) Connectivity..
    3) Just try in rsa1 Settings--->display Generated Objects >selct show generated objects->Continue..
    4) Activate u r ds with the programe "RS_TRANSTRU_ACTIVATE_ALL"
    Hope this will help...
    Regards
    R M K
    Assining points is the only way of saying thanx in SDN ***

  • Error in ODS activation/export datasource

    Hello Gurus,
    When I am activating an ODS 0CFM_O01, it gives the foll error. can u pls guide. thanks in advance
    DataSource 80CFM_O01 does not exist in source system BWCLNT700 of version A     
    Error when creating the export DataSource and dependent
    Error when activating ODS Object 0CFM_O01
    rgds

    hi,
    take a look oss note 597326-Activating ODS: Error when creating the export DataSource.
    base on that note, the activation error coz dependent object(s)-infoobjects not active, to eliminate the error we have to first have all the objects active. you may try in business content installation, collection mode 'manual', put 0CFM_O01, grouping 'only necessary objects', right click 0CFM_O01 and choose 'install all below' then 'install'. hope this helps.
    note 597326
    Activating ODS: Error when creating the export DataSource
    Symptom
    When you activate or transport ODS objects, the following errors appear in the log:
    "The creation of the export DataSource failed". Message number RSBM 035
    "Error &1 in function module &2". Message number RSBM 006
    "Error when creating the export DataSource and dependent Objects". Message number RSDODSO 169
    "Error when activating the ODS object &1". Message number RSDODSO 168
    Other terms
    RSBM 035, RSBM 006, RSDODSO 169, RSDODSO 168
    Reason and Prerequisites
    A characteristic involved is active but it is using new or inactive attributes.
    Characteristics involved are all characteristics used in the ODS object.
    Solution
    Check all characteristics involved as described in the following:
    Check the Compounding and Attributes tabs in the characteristics maintenance.
    All characteristics here must be active. This is displayed by a green icon.
    If this is not the case for a characteristic involved (a gray icon is displayed on one of the two tabs), activate the characteristic involved. This also activates the inactive dependent characteristics.
    After you have checked and repaired all the characteristics involved as described above, the loading/maintenance of master data should work again.

  • Error while generate export datasource.

    Hi Experts,
    APO - 3.0A(BW-2.0A)
    In APO while creating generate export datasource for a cube, I am getting the following error.
    Creation of InfoSource 8XXX for target system BW 1.2 failed - Message no. RSBM 026
    Diagnosis - Failed to create InfoSource &v1& for target system BW 1.2.
    System Response -
    The InfoCube cannot be used as a data mart for a BW 1.2 target system.
    Any help is highly appreciated.
    Thanks&Regards,
    VJ

    Thanks Rebort,
    Just now I completed it after searching for OSS note. Anyhow thanks for you help too.
    Now I am facing a different problem. The generated DM infosource is not available under InfoSource - DM.
    I have changed the ODS setting from Hide to Show
    also InfoSources - RC - insert lost nodes..
    no luck.. any suggestion
    Regards,
    VJ
    Message was edited by: Vijay Kumar

  • Generate Export DataSource from InfoCube In Production System

    Software component : BI release 7.0 SP 18
    Dear Gurus,
    we have a strange situation in our production system from a month till now.
    We want to generate an export data source from an infocube to load data into another one but now when we try to generate in prod ( right click on infocube and select "Generate Export DataSource" ) we can't create anymore.
    Following message appears :
    no changes to repository and cross client customizing object allowed
    and the generation is stopped.
    We always did it in production system in the same way as in the other system and then transported the update rule or transformation, but now it seems that is no more possible.
    No setting has been changhed in SCC4 and in object changeability. Maybe is an authorization problem or is due to any other setting?
    Does anybody has a way to solve this problem?
    <removed by moderator>!
    Kind Regards
    Stefano
    Edited by: Siegfried Szameitat on Nov 24, 2008 4:18 PM

    Hi Stefano,
    If you want to generate an export datasource you ask your basis team to open the system so that you can do.
    As per the Sap Best Practise you can do  the export datasoorce in your development system and move it to the quality and after testing you transport to Production.
    Generallly if you can look in to production authorizations you may have only some operation like to display only.SOme times basis may give authorizations like creation of DTP and Infopacks like that.
    Regards

  • Export Continualy Failing

    I am exporting a Feature Doc that is 94min in length, shot in SD and need to have it transferred to Digibeta uncompressed. I have used numerous codecs (SD 10-bit Uncompressed NTSC, SD 8-bit Uncompressed NTSC, Apple ProRes 422 for Progressive material-HQ) and Compressor will begin to export the job, but then eventually Fail. The Console log says:
    Power-Mac-G5 /Applications/Mail.app/Contents/MacOS/Mail: Error: Embedded profile header length is greater than data length.\n
    There also seems to be numerous errors to debug too. Not sure what this means.
    I'm thinking the project is just to big to export? I also tried exporting a 2min clip from the same project with the same codecs and it worked just fine. What is the best way to export this feature without compressing it and crashing altogether? Do I have a system issue that I need to be concerned with? Am I doing this correctly?
    I appreciate your responses! Thank you!

    I have gone thru the SE38-RSSGPCLA/TRASACTALL but still my 8Zods datasource is not active and its PSA is not active.
    When I do the init for the ODS its says 8zods has no PSA, so I try to generatre export datasource for ODS[which is inactive after trasport] i get a short dump as posted above.
    The change log and theold request[active] are deleted for ODS, BUT the requests do not go away from ODS-manage screen!!
    QUALITYSYS is a copy of PROD and is 3 months back, also we have done many changes to the ods and other datamart kind ods in this landscape after the syscopy.
    Thanks fro all your replies.

  • Flash CS6, QuickTime: The export operation failed because it ran out of memory.

    Exporting a QuickTime movie file seems to be an old issue with previous versions too. In CS6 I always get the error message: "The export operation failed because it ran out of memory." I've got tons of memory and have allocated increasing amounts to the cache with no success.
    My small and fairly simple file was created with Flash CS5 which seemed to work fine at the time of creation. I've tried everything recommended online but with no luck so far. BTW, I reinstalled CS5 and tried that too but it just hangs now, and there's no error message.
    Does anyone have a solution?
    (OS X 10.7.4)

    If I may join this discussion...  I loaded up CS6 two days ago and have just completed my first 60 second animation using it.  Like everybody else here, it all went fine until I tried to export it to QuickTime – something that has never been problematic before. 
    I ended up exporting it as a swf and opening that in CS4.  Then I could export it, but the resulting QuickTime movie was over 500 MB in size!  Okay, so then I opened it in QuickTime Pro and exported it from there.  This brought the file size down to a far more reasonable 35 MB, but now the soundtrack has gone!  So now I am having to replace the sound in Final Cut Pro. 
    This is a real palaver – and not conducive to heaping praise on CS6 when questioned.  I note that there is talk of Adobe rectifying this "bug", but it would be really good to hear from somebody at Adobe with:
    a) An apology
    b) An estimated time of delivery
    c) A best practice work round
    But I'm guessing that anybody that works at Adobe will be the last person to read this...

Maybe you are looking for