Creative sound blaster x-fi platinum is

hey guyswill my new creative sound blaster x-fi platinum be able to connect to my motherboard?firstly, i dont think the cable that comes with the card will connect to my motherboard, is that true? it is an A8N-SLi Premium?also, even if i dont use the front plate, how do i get the soundcard itself to work? I install the drivers but when i try to run the audio console it says "the audio device supported by this application is not detected - the application will exit"any ideas because for this much money if it doesnt work that would suckthanks guys!bobso

ok i've done what you said.i disabled the onboard chipset and put the card in the outermost slot and the soundcard works nowhowever, i tried to connect the front panel and had issues. i used a completly blank IDE cable that has no 'key' pins (only red ribbon on pin ) and once connected (power and everything) when the computer boots it doesnt get past the IDEchecklist thing - i know it is the front-panel at fault because when i disconnect the IDE cable from the mobo then it gets past that point and does the IDE check...do you think the front-panel is at fault or the IDE cable... it is a very old cable that has been stored in an old box with lots dust...really not sure, would like a hand thanks!bobso

Similar Messages

Creative Sound Blaster Audigy ZS And Vista Driver installation prob

HI!
I encounter Installation problems with that file:
Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit XP and Windows Vista Pack .04.0077
I Use Vista 64Bit Ultimate and when I try to install this package I have an error message after my language selection. Is there a known issue for this
Thanks!
Julien

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

Sound blaster Audigy 2zs platinum setup with creative inspire 5.1 digital 5

what should the setup be for the sound blaster Audigy 2zs platinum and the reati've inspire 5. digital 5500 because with the decoder in i only get center fl fr on games. i dont get sound from the rear speakers.but when i take the decoder out and just plug the 3 leads straight into the back of my sound card i get 5. any help plz.i done a thx sound test with the decoder in it does fl i can hear it but i can hear the center as well
and no sound comes out on the 2 rear speakers when doing the test.but when puting the 3 cables straight into the back of the sound card i runed the test and i could hear all the speakers fine even the rear speakers any help plz is this ment 2 happen or do i have to change some settings thanks for any help plz help me thanks.

I Have had a problem for ages. I have the Audigy 2 ZS Platinum and Inspire 5. digital 5500.
I have copied the advice I received/didnt recieve from creative.
Best of luck
Dear Martin
Thanks for your reply
I am sorry for the problem you are facing.
To achieve outputs from all the speaker during speaker test, you will need to have an analog connection, or digital DIN connection.
That will be possible if you connect the three line out jacks on your soundcard, to the three audio input (analog jacks->green,black,orange) on your speaker, if it has this connection. Or, you may connect them using Digital DIN, if they have this connection.
If you are using digital connection (coaxial, optical), there will be no way to achieve sound output from all the speakers during 5. speaker test, as they carry stereo signal.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe:
Original Message Follows:
Hi
I understand you must be busy, so no problem.
No I do not hear EAX when in Pro-logic mode. I only hear (depending on the game in question)
Half life two: front left-right and centre. NO rears
Fear: Front, left, right, & centre. No rears
Farcry Front left, right & centre. No Rears
When I run your speaker test HISSSSS, No Rears, no front left or right
Beats me?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 24 January 2006 5:44
To: Martin
Dear Martin
I apologize for the delay on the answer.
If you select Dolby Prologic mode on the decoder, are you able to listen
the game audio, with EAX, in all of the speakers?
Regarding to the optional bay dri've, you can purchase it from ou
Best Regards
(Mod Note: Name Removed)
Original Message Follows:
Hello
Your email was helpful, unfortunately, not for my unit, you see I would
have
connected the Jack leads in by now if the inspire had Jack lead inputs
as
you describe
Please don't think I am being sarcastic, but from reading the
correspondence
below it would seem as if your department is having difficulty
understanding
my problem.
Also it would seem your department doesn't have the necessary technical
information on your very own product, so to help with your dilemma I
have
taken photos of the input/outputs on the Inspire unit.
You will clearly see the inspire has no inputs other than Coaxial and
Optic.
This leaves me back to my last post. I think the solution would be for
me to
purchase the correct processor, which would have come with the original
sound card had I not been a little tight on the money front.
I have attached a photo of the sound card with the processor, I would
love
to buy this processor but find myself unable to locate this product on
your
web site. Would you possibly be able to send me the correct link to this
item so I can buy this Processor Please?
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 8 January 2006 0:3
To: Martin
Subject: RE: CLE -
Dear Martin
Thanks for your reply
Your soundcard is Audigy 2 ZS
Your speaker is Creative Inspire 5. Digital 5500
You will need to have a 3:3 cable(with the color green, black, orange)
to connect your soundcard to your speaker, to achieve the 5. effects
with games.
Below is the connection:
- Connect line out jack of Audigy 2 ZS
to 'Front' of Creative Inspire 5. Digital 5500 using the green color
connection
- Connect line out 2 jack of Audigy 2 ZS
to 'Rear' of Creative Inspire 5. Digital 5500 using the black color
connection
- Connect line out 3 jack of Audigy 2 ZS
to 'Center/Subwoofer' of Creative Inspire 5. Digital 5500 using the
orange color connection
Once you have done the correct connection, play the game DOOM3.
Ensure you have selected either the EAX or surround option in the game
settings.
Does it work?
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
You have lost me. Your sound card clearly states that I can have EAX
surround decoding from the sound card I have purchased.
All of the games on your web site claim to give me an environmental
effect
that will blow my mind, hence EAX.
All I have done wrong is NOT buying your decoder that comes with the
sound
card. My mistake.
All I want to do is re-address this issue and buy the correct
decoder/processor.
Can you point me to the correct link on your web site so I can buy the
correct decoder/processor?
As for the PCM out of the above cables, this foxes me as my other
equipment
only use Optical cabling on my Lexicon processor and from that I have DD
7., DTS 7. and meridian 5. lossless.
My issue is more to do with NO EAX from the rear and centre channels
while
in-game.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 09:3
To: Martin
Subject: RE: CLE - Technical Support Request (KMM887805I6636L0KM)
Dear Martin
Thanks for your reply
All commercial digital connection eg. optical or coaxial cable will only
carry PCM stereo signal. If you want to output the signal to a surround
5. with extra EAX environment effects, it will not be possible at all
since it is only restricted to stereo channel signal.
As per current industry limitations, we are bound to follow the standard
one-signal output for all our SPDIF and Optical output jacks. This is
something that is currently shared by all vendors for all products.
Please note that all games are not dolby digital, even they are , it
will require certain motherboard to encode it to dolby digital signal,
which our soundcard does not support.
You can only use analog connections to gain true 5. surround for
gaming..
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
Hi Joong
I don't fully understand your email, but I do get the gist of what
you're
saying and understand I need to connect the analogue cable to fully
appreciate the sound in EAX.
Would you be able to tell me what product I could buy from your
catalogue
which would marry up with the sound card I have, as I understand now
that
the Inspire 5. will not do the job.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 04:00
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8875697I6636L0KM)
Dear Martin
Thank you for the reply.
Computer games written with support for 3D audio do not require a Dolby
Digital Interacti've Content Encoder (DICE) to output multichannel sound,
with no exceptions. Sound devices that support the real time encoder
technology from Dolby will simply receive the multichannel wave file
output and encode it in real time to a somewhat modified Dolby Digital
bitstream. Creative does not support the Dolby Digital Interacti've
Content Encoder on any of its sound cards.
The only difference between a Sound Blaster card and an audio card that
has a real time encoder, is that you can make a one-wire, digital
connection from your audio card to your home theater receiver and enjoy
discrete multichannel sound from the game. However there will be a
continuous, slight delay, known as "latency", as the encoder is creating
and transmitting the bitstream, and of course the compression scheme
being used is "lossy" (i.e. not bit-accurate).
If you want to enjoy 3D audio in 3D enabled PC games in multichannel
surround sound with a Sound Blaster card, it is recommended that you
connect the analog outputs of the sound card directly to the analog
inputs of the receiver. This will require 3 cables for 5. surround
sound, one for front right and left, one for rear left and right, and
another one for front center and subwoofer. Though it requires more
cables than a real time encoder system, it will not have any latency
issues. When connecting PC audio to a home theater receiver, Creative's
latest sound cards such as Sound Blaster Audigy, Sound Blaster Audigy 2
are likely to provide higher quality audio than any Dolby Digital real
time encode system available for the PC today.
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Please do not use this link to submit technical queries
Original Message Follows:
Hi
One particular game which has "in-game" DD is Farcry; I used this as my
benchmark disc for DD and to push my Nvidia 7800 GTX GPU's (I have tried
it
on friend's machines and they get the full surround effect so I Know
this
version is ok. I also have ALL of the game patches & updates.
I would like to point out that while playing Doom 3, Half Life 2,Fear,
Colin
McRae rally 04,FIFA 2004,Meddle of honour pacific assault, Rome, Shadow
ops, All these games have EAX HD, which is enabled within the options
menu
"in-game", But I do not get ANY use out of the rear's and I might as
well
listen in stereo.
No, inspire 5500 does not automatically switch while "in-game" when DD
is present as you would expect, but does if it was a Movie, which makes
me
think the DD stream isn't getting to the processor.
I originally thought I could put all this to rest if I could buy the
control
panel that would have come with the Sound card if I had not tried to
save
money, but every time I search your accessories site I get completely
lost,
it really isn't user friendly, the sub-menus are very time consuming and
point you in the wrong direction because they are not categorised as Joe
public would understand
I downloaded your TEST Movies and creative demo player utility, ran it
but
still no EAX HD or DD if that were present.
I want to put this card and Processor into my boys computer (which is
the
same Spec as mine and I will update to the FX series, but I am unwilling
if
I cannot find a logical reason why this set-up cannot work first.
Would it have anything to do with the pins on the Digital out on the
sound
card plug, the one I bought and was attached to the last email? Only
sending
certain channels down to the processor?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 5 January 2006 08:09
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8868993I6636L0KM)
Dear Martin
Thanks for your reply
Your speakers are fine as you mentioned that there is sound from all the
speakers when you are playing movie.
May i know what game are you playing when there are no sound from the
rear speakers?
Have you done the appropriate settings in the game to achieve the 5.
sound?
Is there any game patches that you will need to update?
Does the Dolby Digital LED light up when you are playing the game?
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Servic
Original Message Follows:
Hi
I am sorry; I should have said the Inspire 5. was model number digital
5500
S/N SW330030026.
The inspire has these connection on the back of the processor
>From top/back of unit
Audio Outputs
Front
Rear
Centre/subwoofer
Audio inputs
Audio line in
Coaxial
Optical
DIN
The Din to a remotely located Subwoofer which has the speaker leads
inputting into it. Plus power.
Attached is the creative view of the controls menu and I have attached
the
invoice I was sent, it shows the lead I was told to fit.
As I said, I can now hear DD5. while within a movie from ALL speakers
BUT
no sound from rears during IN GAME DD5.
I do not use this PC for films only games.
Regards
Martin
If you are having a digital connection, it is normal for only get only
front left/right is you use the speaker test option.
http://us.creative.com/support/kb/article.asp?l=3&sid=4858
Speaker test only outputs from two front speakers?
You mentioned that that you are unable to get any sound from the rear
speakers when playing game right? May i know are you using a digital
connection? May i know what speaker settings have been made under
Creative Speaker settings?
Do get back to me on the above.
Thanks
Original Message Follows:
Operating System: Windows XP Professional x64 Edition
Creative Model Number: SBO 350
Computer Brand/Model: home made
Processor/CPU: AMD 64
Memory: Gig DDR 4
BIOS Type/Revision: 5. 39
System Board/Chipset: ASUS A8N-SLI Deluxe
Detailed Problem Description:
I have the above Sound card.
I also own Inspire 5. amp/processor
I Wanted to save money by connecting above sound
card to amp/processor
Connections on sound card made life very difficult
I contacted Creative for help. you told me to buy
an RCA to mini jack cord which also has other connections, from your
web site, (I tried to find
the product number for you, but your sub-menu
system is so poor I couldn't locate the RCA/mini
3.5 /to phono link for you) this cord connects
directly into the digital in, on the sound card (3.5 Mini jack) to the
coaxial input on the
inspire 5. amp/processor.
I have enabled ALL sp-diff settings and digital in
setting on every program/utility/kitchen sink and all.
I have an SP-Diff wire from DVD burner to creative
sound card, and yes its enabled and digital only
is selected.
I can play a DVD and see the inspire 5.
automatically change from Pro-logic to Dolby
digital when it See's an AC-3 stream.
when I try and play ANY game you say has EAX
,2,3,4 I cannot get any sound from my rear
speakers (see above in Dolby Digital ALL speakers
work correctly)
when I enter the set-up menu within the creative
software you supply with the sound card and select
5. speaker, digital only, test the speakers via
the white noise function, all i hear is left and
right noise. no centre, no rears.
I phoned you tech support line, the boy on the
phone didn't have much of a clue about your
product and I had to tell him what connections sit
on the inspire 5. series amp/processor.
I want to build another PC for my son, I want to
add the FX series sound card and amp, but i am not
willing to buy anything until i feel you have
helped me to solve this problem first.
please can you help, I am at the end of my tether
with this sound card.
kind regards
Martin Waite
Message Edited by Daniel-CL on 0-28-2006 :36 PM

My Past, Present & Future with Creative Sound Blaster cards

I wrote a small product review of a Z-series card i regrettably purchased and creative responded. I replied to them and copied+pasted it here. First and foremost please understand this is just an open letter talking about my love for and mostly positive experiences with the Sound Blaster line of cards since the mid-late 1990s.
Attached is an annotated picture of almost all the Creative hardware I've bought over the years.
Take a good long look at that picture. Think about how many songs have been played through those devices, think of how many movies have been heard through those devices, think of how many games made me jump out of my seat from sound effects heard through those devices, and lastly think how many thousands of hours this amounts to.
STOP READING and LOOK at that attached PICTURE.
I use the word 'almost' because it does not include the card I recently purchased off e-bay, which was listed as (and was) mint condition new, and cost me $250.... a Sound Blaster X-Fi Titanium Fatal1ty Champion Series card.
If the direction Creative is going to continue to go is the direction that it's been going over the past handful of years this will be the last Creative product myself or anyone i influence or make purchasing decisions for will ever buy. Being in my mid 30s I'd say you'll miss out on at least another 20-30+ years of future product purchases.
Below is my address of your reply to my review of your product in a piece by piece layout:
"Based on user feedback we've done the following:
- Take up less disk space"
I run two 128GB SSDs in a hardware based (LSI Logic 8704ELP) raid-0 array so the disk footprint of drivers and software is important to me but whatever space you reduced your driver to is trivial.
%ProgramFiles(x86)%\Creative\(ALchemy, AudioCS AutoMode Switcher, Console Launcher, Shared Files, ShareDLL,THX Console, Volume Panel)
in total take up about 100MB of space. reducing this means NOTHING because it does not allow for more hefty software (Games or Design/Drafting/3D-Modelling Software) to be installed. Now if say your driver and software had a 1GB footprint and you reduced it to 500MB that would be significant because 500MB is enough space to account for one or 2 of average installation footprints of the products in the Adobe Creative Suite. Reducing the size from 100MB to 25MB/50MB/75MB is moot.
"- Optimized controls for touch screens"
This point is amusing, why? because you are making the same mistake Microsoft made with Windows 8 & Metro. Most people who buy a creative sound card are putting it in a PC and do not have a touchscreen. I don't manage a lot of computers but the ~200 i am responsible for bypassed Windows 8 (maybe even Windows 9, we'll see) and either moved from Windows XP to Windows 7 or they will be staying with Windows 7 for the foreseeable future. The touch centric design of Windows 8 is a significant part of this decision despite all the things Microsoft did that i think are steps forward (like better native support for multiple display devices to name one example).
"- Streamlined the interface so it's easier to navigate (removed "modes" and have all controls available regardless what you want to use the card for)."
Dumbing-down a product to reach a greater audience is walking the fine line of Quality vs. Quantity. Why you've sacrificed significant Quality to increase Quantity i do not know. While I will agree making 1 interface instead of 3 can be a potential step forward you did more than streamlining the user interface- you removed prominent, useful, and important features.
"- Better tie in with the Windows audio sub-system."
Through out the decade the only problems I experienced with Windows and my Creative products i can count on one hand. The first would be when Microsoft abandoned DirectSound and moved to an UAA based audio stack in Vista forward and your company dropped the ball and Daniel_K picked it up and made working drivers for your products and you went after him... I was one of the people who used his working drivers to make your sound card work properly when you failed to do so. Second was the fact that you people charged for ALchemy when the move to Vista occurred... this was truly a sh*ty thing to do. The third was the X-RAM causing a BSOD (STOP 0x50 - PAGE_FAULT_IN_NONPAGED_AREA) in windows on a regular random basis because of your device drivers and the best working solution was to disable using the X-RAM on the card- a selling point of the cards to begin with (albeit in years prior).
Allow me to elaborate some more while I have time since it's sunday night and the family is busy with other things and will be off to bed thereafter.
Creative's device drivers and software has always been a point of contention. You don't make the install discs available for download on your website for starters. This is a fascist move on your part. Your driver installation procedure and reliability is hit or miss. I personally have not had a lot of trouble with the drivers (only a few hiccups here and there) but i have read on the forums where all sorts of other people have (I'm not in disagreeing that their problems are partially their fault, but that's the price of running Windows instead of buying a Mac). My experience with your driver software suites over the years have been mostly (A) "When it works as expected it's sheer aural bliss beyond that of any other sound card in existence! THIS is why 'Sound Blaster Compatible' was what other companies put on their products, because Creative set the standard for everyone else to meet." but also sometimes (B) "everything installed and worked fine but now something is corrupt and not all the speakers have sound coming from them or the sound is all screwed up and the driver won't uninstall/reinstall/update correctly because it's corrupt and it's not deleting the driver files because windows has the files locked and safe mode isn't helping so now i have to physically remove the card from the PC and try to completely clean out my system of the Creative software. I can't believe they went after Daniel_K the way they did, i wish he'd come back and fix their drivers. Now which box did i put that install cd in...."
There are 2 reasons I've bought Creative sound cards for over a decade now. CMSS 3D when listening to music while working throughout the day and EAX in videogames at night.
I remember the moment when I experienced EAX for the very first time. I was in college and over at a friend's place. He had just got a new game called Thief: The Dark Project. I remember him telling me about something new called EAX and that only Creative cards had it and that it was supposed to be awesome. About an hour later after watching and HEARING him play Thief I was hooked. Creative had secured a place for it's hardware in my budget for every PC i built from that day forward.
Being that I've worked from home for about a decade now I will listen to music while I work and get in an hour or so of gaming at night as time allows. Straight off the bat the first time i ticked that box for CMSS 3D long long ago and heard music coming from every speaker in my home office i was amazed and overwhelmed. Then when you introduced the ability to set the individual speaker distance and volume from the listening position it was the icing on the cake. I was surround by sound. It was SHEER AURAL BLISS. This feature called CMSS 3D would become the second reason I purchased and recommended Creative sound cards for the decade to come.
As i stated in my review, the only reason i bought a new sound card was because the motherboard I was purchasing had no PCI slots (I remember when motherboards stopped having ISA slots as well...). Before making my purchase I read. I read a lot. I read about the changes you made with the X-Fi Titanium HD and then the Recon3D, and the more i read the more a feeling of apprehension began to take hold. Then i got to reading about the Z-series and read about some of the positive changes between it and the Recon3D line of cards and I became a bit more hopeful.
Sadly my apprehension was spot on... Listening to music was a worse experience when compared to my X-Fi Platinum (or even my old Audigy 2)... and did not even come close to justifying the purchase of the card compared to just using the integrated sound capabilities of my motherboard, an ASRock Z87 OC Formula/ac. But none the less I still had EAX to fall back on right? wrong... I installed a couple games, some new and some old, some with EAX and some without, and for about 2 weeks i played a bit of each one to see how the card handled new and old games. Sadly EAX compatibility didn't even matter because it was overshadowed by poor directional audio reproduction... that same front center speaker that was overbearing when listening to music was noticeable when gaming to the point that it was negatively affecting my gaming experience. I tweaked and toggled every setting i could and even uninstalled and reinstalled the drivers and software to try to mitigate this but to my dismay i could not. It was at this point I went weighing my options... and looking for an X-Fi Titanium (NON-HD!) and suffered the capitalist price gouging that occurs in such supply & demand situations... at least i talked the guy down from his original asking price of $300. I bit the bullet on this because chances are this is going to be the last Creative card i ever own...
I've had my Creative Sound Blaster X-Fi Titanium Fatal1ty Champion Series installed for just over a week now. Everything sounds precise and as it should when you have a quality piece of hardware paired with quality software. Directional audio in games comes from all speakers appropriately and not excessively from the front center speaker unless it's supposed to. Ambient music floats through the air all through out the day creating that familiar feeling of sheer aural bliss as it did before. The only downside is I'm getting to experience the problems other people have with this card (strange loud static-like warble EMI type noise coming from speakers, unaffected by windows volume control) but I have found a work around that I'm using on the rare occasion this happens (disable the device in device manager, re-enable device in device manager).
Chances are what i've written above is perhaps an opening soliloquy of the requiem for the Creative Sound Blaster, the card that defined an industry and the company that turned it's back on it. I don't expect anything to come from this letter and I don't expect a meaningful reply from you. You'll probably write me justifying your decisions you've made with your product line and offer some false sincerity about how you are happy i am enjoying my price-gouged discontinued soundcard i had to buy off e-bay because your current line of products are not a step back in your eyes because of the profits they turn. This generation of customers who buy your Platinum HD, or Reco3D or Z-series line of cards probably oblivious to what they are missing out on (through no fault of their own), funny how the bliss of ignorance works and lines your pockets...
It saddens me that i had to buy a discontinued product off e-bay because it's a better product than what your company currently offers. I wish this wasn't the way things turned out. When you dropped the fun presets and finite control of the EAX effects during the transition from the Audigy to the X-Fi line of cards I noticed but since they were not the main reason I owned a Creative card I tolerated it. But now you've gone and ruined the features that were the reasons i bought Creative cards, and this I will not oblige.
My Creative Hardware.jpg

@To the OP:
I own a X-Fi Elite Pro for the past 8 years now.
Since there, this card has faithfullly seen me through 3 major PC upgrades.
I'm currently at a point where, very sadly, much of what you've described is also weighing on my decision to not go for a Z line.
@Creative:
I do hope you're listening and can come up with a solution to a simply design feature - namely a fully working Stereo Surround, like the one that was available in the X-Fi line of cards via CMSS-3D.
Regards,

Pin Specifications for Creative Sound Blaster Audigy SB1394

;Pin Specifications for Creative Sound Blaster Audigy SB394 I have a Sound Blaster Audigy SB934 CA000-IAF Creative Tech '0 AA299J basically a Sound Blaster Audigy Platinum (wiouth the front bay for conectivity.)? And since I dont' have the front bay for heaphone and mic conectivity I was wondering if there is a spec sheet for the 40-Pin conectivity that is used for the front bay. I was wondering if anyone could provide me with such spec sheet so that I can try to conect my frontal Intel board plugs for headphone and microphone (would like to use my headset.)
There are a lot of pins on the card and well only about 8 in the conector for the front plugs. So if any dev from the forum is reading this I would greatly apreciate it if I could use my front Intel sound plugs on this old model card.
Thank you for all your help.

http://www.driverheaven.net/audio-general-technical-discussion/5279-creative-audigy-2-ad_ext-pin-assignment.html
That will help you with the pin assignments.......
And you can also try one of these to connect a lot more easily to your front panel audio jacks.......
www.x-tap.com
I used the above with four Audigy LS and SE's and it works a treat!

Front I/0 panel on Sound Blaster Audigy 2 Platinum ZS not fo

The front I/0 panel on Sound Blaster Audigy 2 Platinum ZS not found by Creative Volume Control Application. Under recording sources, I can only choose from "What you hear", MIDI Synth, S/PDIF-In, CD Digital, Analog Mix (Line/CD/Aux/TAD/PC), Microphone and Wave. The option to record from anything on the front panel, (Aux-in 2, Line-in/Mic-in 2) have disappeared. I have tried re-installing the software from scratch, just installing Creative Update components and even formatting the hard-dri've and re-loading Windows but it still doesn't work!!?Does anybody have any helpful suggestions on this frustrating matter?

If you're using a dynamic microphone, the Audigy 2 ZS dri've bay has a jumper which you can change for it to support dynamic microphones instead of electret microphones. However once this is done you won't be able to use electret mics until you've changed the jumper setting back.

MSI 648 MAX + Sound Blaster Audigy 2 Platinum

Hi.
I have a big problem because my sound blaster audigy 2 platinum doesn't work with this mainboard. When i start any sound blaster program my pc freezes.
What can i do?
Excuse my english
Thank you

Follow this steps
1) Unplug your External Creative Card
2) On computer
3) Go to Bios
4) Set Bios of AC97 to AUTO
5) Reboot
6) If you are using win98, go to the control panel, system, Device manager, click "disable in this hardware profile".
8) Restart computer
9) Off computer
7) Slot your Audigy........everyting should be fine.
If problem stil persist, I can still help you but it is going to be very troublesome.
*Note before you do step 1 remove your AC97 driver first*

Sound Blaster Live! Platinum 5.1 doesn' t wor

I? m the unlucky owner of a Creative Sound Blaster Li've! Platinum 5. card since many years: it never worked and now I? m fed-up?
After having inserted the relevant CD-ROM I proceed with complete Setup, but after installing all the files these are the results for the 2 main functions I? m interested with:
? CTRec.EXE has committed error and will be closed. The program needs to be restarted. The creation of the error registry is under way
? DIAGNOSE.EXE has committed error and will be closed. The program needs to be restarted. The creation of the error registry is under way
BTW the last sentence is not true, since no error registry is created at all (at least not in the form of a LOG file as I?d expect?
Why?
What can I do?
Lucio LUX Peres, Milan, Italy

You may have to use the connection on the rear of the sound card...there should have had a "Y" shaped cable included with the speaker/sound card..it has a small 1/8" plug on the single end and opens to a din plug and rca type pluge on the other...try the single end in the orange input at the sound card and the other two plug in to the speaker system..sorry bout being so vaugue, i'm kinda tired..but if you need the original speaker system/ sound card owner's manuals with the installation diagrams I can get them to you.

Sound Blaster X-Fi Platinum + What You Hear

Hi All,
I'm looking into picking up a Sound Blaster X-Fi Platinum or the X-Fi Platinum Fatalty Champion Series card... However after recent frustration loosing the "What U Hear" option on a old Audigy SE running under Windows Vista, I am a little unsure!
My question is: Do the X-Fi Platinum or Fatalty Champion Series cards have the "What U Hear" recording option like it did with previous older Creative cards? *I am now back using Windows XP*
Also, are the 2 mentioned X-Fi cards much cop when it comes to music production?
Many thanks

Well looking over [url="http://www.xbitlabs.com/articles/multimedia/display/creative-soundblaster-xfi.html">here[/url]?you see the Creative SoundBlaster X-Fi Sound Card Family Review.
Note...[*]ASIO 2.0 support at 6-bit/44.kHz, 6-bit/48kHz, 24-bit/44.kHz 24-bit/48kHz and 24-bit/96kHz with direct monitoring.<?
ASIO 2.0 seems a different ball game all together.
We know that not all those card will NOT give you What U hear in Vista, so I think it's bad to get the terms confused.
You can find the same on some USB eternals as well, and I've yet to see one than that can do mix (What U hear)
I?suggested to?creative in another thread if they could supply this information rather than let someone buy the card to find out it doesn't.
Worth noting that creative have stated what cards can do What U hear in Vista tho.
The What U Hear recording option is supported in Windows Vista for Sound Blaster X-Fi series (Excluding Extreme Audio series) and Sound Blaster Audigy series (excluding Sound Blaster Audigy LE, SE, and Audigy Value).
Some of those card will with older drivers though.
This whole Stereo mix thing has become a total sham, and is not provided on most new laptops with vista and creatives external solution ( X-Fi Xtreme Audio Notebook) doesn't give it in Vista but it does XP but you CANNOT do voice over music with it as you have mic control and it mutes the mic.
I suppose it depends what we use mix for though....some people just want it to record from the web, so they are not bothered about the mic, but if you want to do voice over music (karaoke or DJ) it's no good.
I could give you a link to a forum where people are cursing the lack of mix, and I can see it getting worse as people get new PCs with Vista on.
Sorry I went off topic, but I needed a vent over this as I often get asked by people "what should I buy" and I can't find the answers!
Come on Creative!!!!![/list]

Sound Blaster Live 24-bit PCI Sound Card and Creative Sound Blaster PCI Card not detect

Ok here is my problem. I bought a Creative Sound Blaster PCI sound card a while back and it was working fine but recently when I would boot up my computer and try to play music say off of Winamp it says Bad DirectSound Driver. When I check device manager it shows no sound card there and in sounds and audio devices it says no audio device. Now my brother believed this to be a card fault so we went to Frys and bought a Sound Blaster Li've 24-bit PCI card. I uninstalled the old drivers and installed this new one but yet it's the same problem. My assumption was that Windows XP had something conflicting so I reinstalled the OS. It found the card and I installed the latest drivers?off of this site but now it does the same thing yet again with a fresh install of Windows XP. The card has been in all 3 of my PCI slots and it will detect it for a moment but then acts like as if the card was never installed. Like I never installed a sound card into the computer. The onboard audio has been disabled for a while now but I do not know what the problem could be. I did Scan for hardware changes but it doesn't show up. Sometimes when the card is detected if I do scan for hardware changes and the card is there it will just magically disappear from the device manager as if it was never there. Even when I try to load music and I see the card is detected it will not play the music and ends up locking up Winamp to the point that sometimes will go BSOD. Now I would really like to find out what the issue is because I am planning this weekend to swap out my motherboard with a duplicate board to see if that will end up fixing the problem but I want to find out if there is any other way to fix this issue. Thank you.Message Edited by AuXoIs on 02-25-200808:28 PM

Hmm what other options is there for the bios on PCI slots?Also anything you connect to the motherboard can have oxidization (I think its that) build up on the connection. Check the connector on the card and get a eraser (Pen eraser is better) and give it a good cleaning. The connector might have alot of build-up on it and you can see it by a dark yellowy colour. I cleaned my graphics card and ram connectors after they got alot of the build-up on them. On a older computer my graphics stopped working and this fixed it. Also I went away for a while (like a month) and came back to see that my puter didn't display anything. Opened it up and saw that the graphic card had alot of corrosion? on the card connector and in the slot. Does that if you computer is turned of for a long time. Had a heck of time trying to clean the slot out. One other thing that it could be is the sound card is faulty. I had an audigy 2 and it died a while back . It picks it up and then try and use it computer freezes and the after restart it's not there anymore. Hope it's not that problem. Hope this gives you something to go by.

Creative Sound Blaster AudioPCI 64V (WDM) Prob

Hello,I have a Creative Sound Blaster AudioPCI 64V (WDM) card. I did something that affected the drivers. The sound has stopped working. When I try to use a sound application, (such as media player or sound recorder or anything), I get an error message saying the sound card is not installed. I have tried several times to reinstall it using Add New Hardware, but it still won't work.What do I need to do?Thanks.

KDNenakh wrote:
Notify me about changes, though...
What the card supports (on the outputs) won't change, this is also an older card. I'm not familiar with that particular C-Media chip, but if it's on a recent motherboard it may be newer than the CT480, which is an old card.
Cat

CREATIVE SOUND BLASTER LIVE 5 voice dist

I have a CREATIVE SOUND BLASTER LIVE 5, I want to know if some?software of Creative labs?exists to distort the voice in real time.Pablo Castillo R.
http://pablocr.pe.kzMessage Edited by pcr_sof on 06-08-200709:48 PM
Message Edited by pcr_sof on 06-2-200708:36 PM

Take a look at the following thread:http://forums.creative.com/creativel...message.id=994?That is the best you can get. Did you run WindowsUpdate to get the drivers installed?If you did, just change the speaker setup to?4 speakers, then check and uncheck the?Digital Output Only checkbox to get sound back.

Creative sound blaster vibra

Can i install creative sound blaster vibra 28 on a core 2 duo 2.33, intel ?q33 chipset ?

Maybe the card?is a PCI 2. one. And your mainboard is a 2.3, so there is maybe the problem, that your maiunboard does not support 5V to PCI BUS. So maybe the card wont work because of this. But it can be another failure. maybe the card is defecti've.
If your PC doesnt boot, a driver wont help you...

Creative Sound Blaster 24 bit l

Please Can You Help?creative sound blaster 24 bit li've will it work on my xp as it states that i have to have XP (SP) and i have got xp sp2?thank you.

Thank You Stormy3
I will go out and buy it, when?I was on windows 98?I had the creative sound blaster 28can?I get one for my xp instead of sound blaster 24 bit li've?

Creative Sound Blaster Audigy Value/SE/LS Driver 01.04.0

Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit Vista Beta Driver 0.04.0055
Yeah, 32-bit, wooo.
When will a 64-bit version be available?

Has anyone tried the "AMD64" Driver for the Audigy Value (I assume this is the SE?) that is on the bundled CD?
I tried different driversets from the download/support site to no avail.
I didn't think about the CD driver until I got to work this morning.
Really wishing I picked up the Li've! (yesterday) instead of the Audigy Value now
...expected this card to have a better chance, especially with "x64 drivers" on the box.
Oh well, I'll give it one more shot tonight with those CD drivers... hopefully something will work.Message Edited by abz on 2-07-200604:08 PM

Creative sound blaster x-fi platinum is

Similar Messages

Maybe you are looking for