CRS-1 plaspa port and jacket slot

Hi Expert,
I need to replace SPA card to resolve the error
%L2-PLIM_ASIC-4-HW_WARNING : plaspa instance 0: (plaspa port 2 jacket slot 0) RSI Spi Error was reported
The plaspa port 2 jacket slot 0 would be SPA slot 0 (0/0/0), correct?
NAME: "0/PL0/*", DESCR: "Cisco Carrier Routing System SPA Interface Processor Card"
PID: CRS1-SIP-800      , VID: V04
NAME: "0/0/0", DESCR: "2-port OC48/STM16 POS/RPR Shared Port Adapter"
PID: SPA-2XOC48POS/RPR , VID: V02
NAME: "POS0/0/0/0", DESCR: "OC48 SR/STM16 I-16"
PID: SFP-OC48-SR         , VID: V01 ,
NAME: "POS0/0/0/1", DESCR: "OC48 SR/STM16 I-16"
PID: SFP-OC48-SR         , VID: V01 ,
NAME: "0/0/2", DESCR: "2-port OC48/STM16 POS/RPR Shared Port Adapter"
PID: SPA-2XOC48POS/RPR , VID: V02
Thank you for all replies

I didn't see any errors on SONET interface from command show controller SONET 0/0/0/0 and 0/0/0/1
RP/0/RP0/CPU0:TH-ICR-TT1#sh controller SONET 0/0/0/0
Thu Apr 5 17:29:23.737 GMT
Port SONET0/0/0/0:
Status: Up
Loopback: None
SECTION
LOF = 38         LOS    = 20                           BIP(B1) = 2761538
LINE
AIS = 4          RDI    = 63         FEBE = 21712298   BIP(B2) = 6871279
PATH
AIS = 112        RDI    = 441        FEBE = 674410     BIP(B3) = 4673236
LOP = 62         NEWPTR = 422        PSE = 10093      NSE     = 17398
PLM = 136        TIM    = 60         UNEQ = 0
Line delays trigger:      0 ms clear: 10000 ms
Path delays trigger:      0 ms,      0 ms (configured), clear: 10000 ms
Last clearing of "show controllers SONET" counters never
Detected Alarms: None
Asserted Alarms: None
Mask for Detected->Asserted: None
Detected Alerts: None
Reported Alerts: None
Mask for Detected->Reported: None
Alarm reporting enabled for: SLOS SLOF SF_BER PLOP
Alert reporting enabled for: B1-TCA B2-TCA B3-TCA
Framing: SONET
SPE Scrambling: Enabled
C2 State: Stable   C2_rx = 0x16 (22)   C2_tx = 0x16 (22) / Scrambling Derived
S1S0(tx): 0x2 S1S0(rx): 0x2 / Configured
PATH TRACE BUFFER : STABLE
Remote hostname : SG-ICR-GS1
Remote interface: POS0/0/0/1
Remote IP addr : 122.144.20.28
APS
No APS Group Configured
Rx(K1/K2) : 0x00/0x00
Tx(K1/K2) : 0x00/0x00
Remote Rx(K1/K2): 01/0   Remote Tx(K1/K2): 01/0
BER thresholds: SF = 10e-3 SD = 10e-6
TCA thresholds: B1 = 10e-6 B2 = 10e-6 B3 = 10e-6
Optics type: OC48 SR/STM16 I-16
Clock source: internal (actual) internal (configured)
Rx S1: 0x2 Tx S1: 0x0
Optical Power Monitoring (accuracy: +/- 1dB)
Rx power = 0.0032 mW, -24.9 dBm
Tx power = 0.2181 mW, -6.6 dBm
Tx laser current bias = 22.0 mA

Similar Messages

USB ports and memory card slots not working

My Pavilion a6120n desktop has worked brilliantly ever since I purchased it. As of last week the 2 usb ports in the front and the 2 unused usb ports in the back have stopped working. My printer is plugged into one rear port and my wireless mouse is plugged into a second rear port and these work fine. I generally use a memory stick for data swapping or the card reader slots (which have also stopped working). I no longer see the memory card icons in the "Computer" window. When installing something new the "New Hardware Found" statement pops up but the driver install always fails. I think it is a software issue but there are no usb drivers to download on the HP/support site that I can find. . . so . . . Below is what I have tried so far.Run antivirus software. Full scan & memory scan - no issuesRun malewarebytes full scan - no issues I have tried restarting several times with no success. Restore to several previous restore points = failedRestarting computer in repair mode = failedRun the repair disk that I had made = failedChecked the power management for each usb port to see if the power was routed properly = okRemoved the case cover and carefully inspected the wiring and connectors.finally I tried uninstalling the usb drivers = failed Upon restarting the computer the last time the startup file must have failed and after several hours of attempting a repair I had to reinstall the Window 7 completely. Still no usb or memory card function. Any help would be appreciated Thanks,MrBob38

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how the USB ports and memory card slots are not working, and I would be happy to assist you in this matter! Since you mentioned that you have already re-installed Windows 7 on your computer, and the USB ports still do not work, please contact our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
www.hp.com/contacthp/
I hope this helps!
Regards

My USB ports and SD card slot aren't working!

My USB ports and SD card slot haven't been working on my MacBook Pro for a couple of months now, and I have taken it into Future shop to get it fixed under my warranty. Unfortunately my warranty was expired by a month (Oops), and the associate helping me said that there was no power getting to the ports because it had something to do with the circuit board, and that it would cost $900.00 to get it repaired. I can still charge my MacBook, and the CD hardrive works completely fine.
My goal is get my MacBook repaired for little or no cost. I was wondering if anyone knows a solution to this, or how much it would cost me to get it repaired at the Apple store.

What version of OS X is the Macbook Pro running?
In OS 10.8, you can do this:
With the iPod connected, go to Apple Menu / About This Mac / More Info / System Report.
click on USB under Hardware (in the left column).
Does the iPod appear anywhere on the right hand side (USB Device Tree)?

CRS with 10GE port

Hi ,
As of now we use 1 port 10GE card only (Cisco 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA) in our CRS connects to Core backbone.
We might need 10GE for access now to provide 10GE to PE ( pure ethernet not any optical technology).
I was trying to find out the line card support more 10GE port density for this purpose. Cisco support 8 port 10GE module but that is not SPA rather normal Ethernet card (Cisco CRS-1 8-Port 10 Gigabit Ethernet Interface Module). How is it diff than SPA to use for PE-P - MPLS link includes LSP, Qos etc feature....
Can I use this 8 port 10GE card for the above puropse ? Important thing there should not be any major limitation
Regards,
Chintan

Hello Chintan,
in other platforms we are used to see more features or different features supported on SPA modules.
the datasheet of the 8 TenGiga
http://www.cisco.com/en/US/prod/collateral/routers/ps5763/ps5862/product_data_sheet09186a008022d5e9.html
About SW it just says:
Software Compatibility
Cisco IOS XR Software Release 3.0 or later
the list of features for SPA GE and 10GE
http://www.cisco.com/en/US/prod/collateral/modules/ps6267/product_data_sheet0900aecd804d884d_ps5763_Products_Data_Sheet.html
There is some more detail.
then I've gone to
www.cisco.com/go/crs
but I've found no useful info
Looking at the configuration guides, the QoS for example I didn't find any distinction about the linecards
http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.7/qos/configuration/guide/qc37fab.html#wp998930
Ask to your cisco account manager or even open a TAC service request to request info to be sure.
Hope to help
Giuseppe

Why would the Firewire Port and/or External DVD-RW suddenly not work?

Hi, it's me again. I swear, I must be destined to just use Windows machines...
Anyways, I have a used/refurbished iBook G3 500MHz 320MB RAM Dual USB (1 Firewire)laptop running OS 10.2.8 that I bought a few months ago. I went and purchased an external Firewire/USB 2.0 DVD-RW drive as I only had a CD-ROM drive on my machine and I wanted the option to burn CD's or watch/read data from DVD's (I know that with my slow processor writing DVD's -other than data- would be a stretch and have other machines to do that with anyways so it wasn't a concern really). I received it and installed it, also installed the free version of Toast that came with it, and the drive worked fine. I have not needed to use the drive since then and have not used the laptop much at all since then really, but I do need to say that I did end up adding a new user account, though I can't remember if I changed the original Admin account and then still have the one I created myself when I first started the laptop after I bought it (had a fresh install of Jaguar on it, but I have no disk to re-install with if needed) or if I created a separate (new) account and ended up deleting the Original Admin accout (I know in Windows, you cannot delete the original Admin account but I do not know if that is the same for OSX or not). I did this as I wanted a master Admin account that I just wouldn't really use and then wanted the other as my main account (and use it to connect to my home windows network) and for some reason it would not let me put a check in the box to allow that account to do so (from either Apple or my user accounts) and so I know that my main user account now is set up to allow it (was it the old Apple user account or a new one, I can't remember- sorry).
Ok, so that is the back story to my problem, which happens to be this:
I just bought a new chip of RAM (512MB to make it a machine with 576MB RAM total) and as I had been looking at getting OSX Tiger (but didn't want to do it without the extra ram and had been considering Panther instead as well), I thought it was necessary if I wanted to not bog down my machine. I bought the Install Disks on DVD for Panther, as well as an upgrade disk (DVD again) for Tiger, therefore letting me use the External Firewire DVD-RW to install Panther, and if I liked I could go ahead and upgrade to Tiger (and if I didn't like it too much, or it slowed things down too much etc, then I could always go back to panther and have both available for future options). The extra RAM coming in handy here definitely.
So I was going to install the RAM today, and decided to go ahead and test out the External DVD to make sure it could boot from it (before making any changes to my system) and then go and install the RAM, and after that, install Panther to start... But I plugged all the cords and cables in, used my laptop with AC power even, and I could not get the External to show up at all... (kinda like the very current post right below mine but for the G4- it worked before, but now the firewire External just does not show up).
I only have USB 1.1 on this laptop obviously, and I don't even know if you could do a boot from an external with USB 2.0 if my laptop had it (the DVD player does). I was recommended to boot with an external firewire DVD or firewire to another machine with DVD capabilities to do the install. So my problem right now is getting slightly bigger, as of course, I can't seem to momentarily find the stuff that came with the External (spare USB cable to check and see if the laptop will recognize it at least with that and to show it is the firewire that is not working properly, or the disk that I used to install it -might have been only used to install Toast free version if it didn't need any drivers, but I don't know where that or the instructions for installation sheet currently is -- I am looking for it, but I have switched bedrooms just last week and I also seem to be missing a few other Windows laptop disks as well so there is a good chance that they are all together, I just need to figure out where, heh.)
I am waiting currently before installing the memory, though if I don't get the External working tonight, I may go ahead and do it first as at least I will have more memory on my laptop then, until I can get other stuff functioning and be able to do the Panther install.
But my main question is, is there something that would cause an installed external to suddenly not show up in OSX? Since I hadn't used it since that one day, and it was unplugged from the laptop itself, would that end up doing it, or more likely, the changing of the user accounts (though I have been trying to test it with different types of media and through both of my user account (which are both "admin" ones), though I do still have one of those being an account that was on there when the External DVD was first installed, so it really shouldn't have done this at all (one would think). So how big of a chance is it that the firewire has somehow gone dead and this is the main culprit to my wasting the past 4 hours on this???
I am currently scavenging around for an extra USB cable to try and test the External that way and will post the results when I can... I love the look and idea of macs, now I have a mac and want to upgrade it even, but why is it that whenever I attempt to use it after having not used it for a bit (and try to make the iBook feel better by using it more as I am sure it feels sad and alone sitting on the shelf while my Windows Laptop gets more attention), or try to fix it when it can be made better (and therefore used more often), the mac (all macs really), just seem to get all pissy and cause problems and make me spend hours upon hours trying to get things to work again??? You have to admit it, I am "mac cursed"... sigh I can program in 4 or 5 computer languages and am very advanced at many tech things (the ones I am not as good at I am still usually Average or Medium skilled) so it makes me wonder why I have so many tech problems with Macs when they are supposed to be the "easy" OS to use...

Actually, I think I have it all working now. After going back to the Plextor Website, I found out that the switch between the USB and 1394 ports only gets activated (switched over to the other) with you turn the device off first, move the switch and then turn it back on. I was sure that I had done this with the ibook, but maybe not as when I went back and did it with first the USB and then the Firewire cables, it did work. I definitely knew that I had not done this with the Windows laptop, the reason it would not have the USB work for me on it.
but back to the iBook, I was confused as it was only showing up as a DVD-ROM (which I guess is what they do until you actually open up the burning software to then be able to burn to it), and it also had the wrong Model #, which after more research, showed that it was the Internal DVD drive model version (PX-708A) compared to the actual model version (PX-708UF) which is the USB/Firewire (External) model. The firmware was really out of date as well (from June 2004 I think, v1.06) and they had v1.12 from Spet/Oct 2006 available so I went to get that (which was a hassle). They had nice easy Windows self extractor/installer packs, and then the BIN files for use for all systems (Sun OS/ Mac OSX/ Mac OS/ Linux etc as well as usable for Windows), and those needed a special Firmware Updater Application which was OS specific. Only I had the hardest time trying to get the OSX one as it would send me to a FTP site and not give me any clues as to which file(s) I needed to get and the Mac OS version was just for older 9.2 or below versions and didn't want to install under the OS Classic mode.
I ended up using my windows computer which made it easier to view with the FTP stuff as I have FireFTP in Firefox, and downloaded the files I thought I needed (to test out), and then realized my silliness, and just downloaded (as well) the Windows Auto Extractor/Installer as the Firmware is the same for all OS's, just the way to install/update it was different... So I hooked the DVD drive to my PC and updated the firmware, checked it out on here before moving it back to the ibook, where I checked that it still worked and had the new update version showing, which it did, and now I have my fully working and newly updated drive ready for the OSX installations... I had attempted to update my Jaguar system as well while online, but it had no new updates available (I guess those were all mostly Tiger updates that were just recently released).
I am now off to install my additional RAM, and after checking that it all shows up correctly, I will go ahead and do the Panther Install (and test it out and see if I like it or not).
For anyone that currently uses Panther on any mac, are there still any major problems I should know about before hand, or know about things that they have mostly fixed (like the issues with Firewire ports and External Drives that they had around the time Panther was first released for example)???
Thanks to all that helped... I now know to attempt an "eject" of any external HD (which I do have one that I will setup to use after I get Panther on the ibook) or CD/DVD drive instead of just unplugging the USB/Firewire cable.

K9A2 Platinum esata port and Install and Usage of esata External Hard Drive

I just bought a sata hard drive and an icy dock enclosure for backup purposes. Having never used one before can someone explain how this works?
I have the hard drive in the enclosure, no problem there. I plugged it into the esata port on the back of my motherboard, but vista won't recognize it and when I reboot and go into the BIOS, I don't see it there either. I have purchased Acronis True Image 11 Home for backup and mirroring purposes. I wish to mirror my existing internal drive to this new external drive.
Questions:
1. Can I use the esata ports on the motherboard for this drive, or should I use the PCI bracket and plug it into one of the existing sata ports on the motherboard? If esata port, exactly how do they work? Are there BIOS settings for the esata ports or do they operate more like a usb connection?
2. Do I need to do anything with this drive before using it; format, install operating system...??
3. Are the esata external drive considered plug and play or do I need to plug it in before I boot my computer.
TIA.

Everything seems to be working as I would have expected at this point, with the exception of the size of the mirrored drives.
I decided to make another mirror onto the 3rd drive making all 3 drives identical. So now I would expect all three drives to show the same "GB free" while viewing with Vista explorer. The odd thing is, is that which ever drive I make bootable - SATA5 port and becomes the C: drive, shows 226GB free. The other drives, either as E: or J: will show as 268GB free. Most be an Acronis or Acronis user (me) issue/oddity?
But bottom line, the sata and esata ports seem to be working as I would expect. Though plugging the external hard drive in before booting (power on or off, needs to be unplugged from the esata port) seems to hang at the FasTrack screen as described above.
My only guess to why this all seems to be working currently is that I don't think I ever had my bios set correctly. After enabling the onboard controller, having the drive actually plugged into SATA5, then rebooting, selecting boot sequence and selecting the raid drive as the first boot device. At least this is my recollection, I made so many bios changes previously that I thought I had it all covered.
Any thoughts? I think I will try to get an answer on the Acronis size difference before I try to setup my RIAD 1, since that would require erasing two drives, per your instructions here: https://forum-en.msi.com/index.php?topic=113738.0
Thanks for help once again.

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
https://discussions.apple.com/community/appletv/appletv

My TV only has 1 HDMI port and it is connected to the cable box. What do I need to connect Apple TV?

What do I need to get in order for my Apple TV to work with my TV? My TV only has 1 HDMI port and this cable is plugged into my cable box. Thank you in advance

Thank you very much! I will return my splitter and pick up a switch.

HDMI, Mini Display Port and Mountain Lion

Hello,
After reading about numerous issues concerning the Mini Display Port and Mountain Lion, I'm trying to discuss it here with you all to see if there is any solution.
I have a MacBook Pro (2009), and used it with my TV (HDMI cable + Mini display port adaptor) with Plex media center back when it was on OS X Lion. It was very convenient because as a portable computer, it could easily be set near the TV and allow the use of a remote to sit in the couch and stream media from the Time Capsule… without the help of any expansive box. Perfect setup I've had for over a year.
The thing is, since I've upgraded to Mountain Lion, when I try to connect the MacBook Pro to the TV, the screen turns blue as if it was calculating the resolution of the monitor so… ok. Until it comes back, and nothing changed either on the MacBook Pro screen or on the TV.
Harware side, I've tried with the computer open, closed, I've checked every port and connection on both computer, TV and adaptor.
Software side, what I find really annoying in Mountain Lion is that they completely ditched every monitor setting as long as nothing is connected — and even if the Mini DP is connected… the Mac thinks it's not. I even tried to reset the PRAM. This is a nightmare.
I've tried to do the same with my iMac (mid 2011), and it all worked properly. What I can't explain is why it works on my iMac and not on the MBP… as they have the same configuration !
I don't know if Apple is outcasting old devices so people buy new Apple stuff or if they ditched the HDMI out on certain (old) devices on purpose so users replace it by the new airplay mirroring feature and buy the Apple TV. I won't, because let's say it's a total crap compared to other media center solutions. And I'm bored of Apple.
Please, HELP NEEDED ! Has anyone had the same issue ? I bet you have ! Now how can we solve that ?
Thank you for your time.

EDIT : stopped working on iMac too… then update 10.8.2 fixed the issue. Now it works. Thanks Apple for temporarily removing some features ! It's just so ANNOYING.
Hope you gonna stay with the few we have left on Mac and stop removing things randomly. Not event talking about the pro environment (designers, developpers, etc.) that is almost gone. 2 years and our macs will be tablets. Careful with the old clients… it's been almost 10 years I'm on a Mac and I've never been so unhappy.

Need a mini display port and audio to HDMI adapter for mid 2009 13" macbookpro

Can some body recomend an adapter cable that plugs into the audio (mid 2009 MacBookPro 13") and mini display port and outputs to HDMI with audio and video all together for a TV? I would rather not run a separate audio cable in addition to the HDMI cable.

http://www.kanexlive.com/iadapt51 - 5.1-channel surround sound from sources that provide such a signal
http://www.kanexlive.com/iadapt20 - 2-channel stereo sound

Can i use the HDMI port and the Mini displayport to HDMI adapter simultaneously to switch between two displays?

I just bought a new Mac Mini and was hoping that i can connect my TV via the HDMI port and also connect a 19" monitor via the Minidispaly port to HDMI adapter or the Mini DisplayPort to VGA Adapter. This way i can pick between having the screen mirrored to my tv, or having the screen displayed at my desk.
Is this possible?

Yes. Note the resolution via HDM is limited to
This model simultaneously supports 1920x1200 on an HDMI or a DVI display (using the included HDMI-to-DVI adapter) and2560x1600 on a Thunderbolt or Mini DisplayPort display or even a VGA display (with an optional Mini DisplayPort-to-VGA adapter, which is compatible with the Thunderbolt port).
HD 4000 Mini Video

I have 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II. How do I connect? 4000 only has 1 Display Port and 1 DVI. 5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute?

I just bought a 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II. How do I connect? 4000 only has 1 Display Port and 1 DVI. 5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute any work at all? I read where on a PC they would work together, but on a MAC they do not.
I read that Display Port has higher band width than DVI, NEC monitors for best performance they recommend using DIsplay Port.
When I was setting this up I looked at a Nvidia Quadro 4000, unfortunately it was for PC, it had 2 Display Ports, in the Mac version they reduce it to one. I did not think there could be a difference.
Mainly want to use it for CS6 and LR4.
How to proceed???
I do not want to use the Quadro 4000 for both, that would not optimize both monitors, one DP and 1 DVI. Using just the 5770 would work but I do not think the 4000 would be doing anything, and the 5770 has been replaced by the 5870.more bandwidth.
Any ideas, I am a Mac newbie, have not ever tried a Mac Pro, just bought off ebay and now I have these problems.
As a last resort I could sell both and get a 5870. That would work, I'm sure of that, it's just that I wanted the better graphics card.
Thanks,
Bill

The Hatter,
I am a novice at Mac so I read all I can. From what I understand the NEC monitors I bought require Display Port for their maximum performance. The GTX 680 only has DVI outputs. Difference from what I understand is larger bandwidth with the DP.
You said I have the 4000 for CUDA. I am not all that familiar with CUDA and when I do read about it I do not understand it.
A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000. Is the 4000 doing anything with nothing connected? I read where in a PC system the 2 cards would interact but in a Mac system they do not.
Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are. I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4. Those NEC monitors are supposed to be top notch.

I have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way f

i have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way for me to use to use my monitor. I monitor LG FLATRON E2041 brand .. PLEASE Helpp ME

i have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way for me to use to use my monitor. I monitor LG FLATRON E2041 brand .. PLEASE Helpp ME

HI, I am trying to connect my macbook pro, 18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector. It all fits but the there is nothing happening? no mirroring option. Any ideas?

HI, I am trying to connect my macbook pro, 18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector. It all fits but the there is nothing happening? no mirroring option. Any ideas appreciated. Many thanks

to get to the Detect Displays button you have to hold down the Option key and the button appears.
SeanfromFulham wrote:
Many thanks, however I don't seem to have any relevant options under displays.

How can I have a program prompt a user to input a selected number of simultaneous (different devices run off com/rs232 ports) and be able to compile all the data and/or graph it simultaneously?

I have a project that I'm working on that I could use some help on.
Some background on it is I'm taking data from a balance via RS-232 (can be a selectable list of balances), and then communicating with them on their own separate COM port. I need these to then run in parallel to then take masses in regular increments and then output them to a graph and/or TDMS file.
What I'm trying to have is that a subVI prompts the user to how many simultaneous runs will be going.
Then I will want multiple pop prompts (one for each simultaneous run) which will have initial data input (data cluster) and then associate these with the COM port and the specified balance.
I initially thought of utilizing a For Loop this way but I can't get these windows to pop up multiple times while storing their own values in say a cluster array. Can anyone give me any ideas to get me a little further?

Cameron,
I've created a prompt for the user to select the number or runs to be run simultaneously.
This then should trigger the amount of prompts the user needs to input - ie VISA resource, and headers to label the "samples".
I want this to be done in multiples (somewhere around 1-10 simultaneous runs - bounded by the program) so that data points from multiple sources can be taken and graphed/saved to file. I just am having issues with the loop situation to be able to keep prompting the user X times and also output the data to the front panel. Originally i thought I could somehow manipulate a tab control container but I'm getting roadblocked.
Does that help you understand what I'm trying to do?
I've attached an image of what I want the user to input for each sampling.
Attachments:
Capture11.JPG ‏24 KB

CRS-1 plaspa port and jacket slot

Similar Messages

Maybe you are looking for