CRS monitoring and recording

Hi all:
We have CRS 5.0 installed with agents using softphones. Some of the agents work in different LAN than CRS. That LAN is connected to the CRS LAN thru a WAN link. Those agents cannot be monitored or their calls cannot be recorder. After some researching, seems that issue is with PC MAC source address, that are changed when going thru router, then it is not recording calls.
Is there any solution or workaround to overcome this?
Thanks in advance.
W.

In case of soft phones you really cannot do much you have to be able to tap into the RTP to be able to record etc.
IF you have cisco phones easy solution is to plug the PC back of the phone powered by the same environment.
please rate if it helps.
Good luck,
Baseer.

Similar Messages

  • How to fix problem "PYLR2000 error playing a file. Try again or contact your Monitoring and Recording administrator"

    Hi,
    I'm using qm 8.5.2 (endpoint recording) most of customer PCs cannot play recording file in application.
    When I launch application and try to play recoding file, it is stuck and show error message "PYLR2000 error playing a file. Try again or contact your Monitoring and Recording administrator." I've install all cilent requirements (validate pc is pass). The error still occur. Even though all requirements are complete .
    So, How to fix this problem.
    Thank in advance
    Namkhao

    Hi bsetexast,
    I'm fix this problem by using Java(TM) version 6.0.200.2 that can be download from UCCX when first run CSD (supervisor desktop). Even other higher java version is valid but this problem still occur. If you install higher version, you should uninstall it first and install this version as well.
    If you cannot find them, I will send you via email.

  • How do I monitor and record a MIDI instrument on Garageband?

    I may be missing something simple in Garageband setup. I want to monitor and record a drumkit via its MIDI output. It is a Yamaha DTXplorer so I have Subtlesoft Midipipe installed and a Focusrite Saffire 6 USB converter. Microphones and guitars are being monitored and recorded with without problem. When I connect the Focusrite to my Macbook air and drumkit the MIDI indicators are blank, no MIDI input detected by Garageband. Then I close GB and launch Midipipe, the MIDI input detected light on the Focusrite illuminates and GB detects one MIDI input (Saffire 6) in preferences window. But if I select new track/software instrument Saffire 6 input is grayed out and so cannot be selected (if I select the mic or guitar sources it is bold and can be selected). If I go ahead and create the software instrument there is no monitor button and nothing is heard or recorded.

    What is the best way to uninstall and reinstall the Focusrite MIDI interface driver. And to uninstall and reinstall the Subtlesoft Midipipe (which is required to get the correct mapping for a Yamaha drumkit)? This was done for me at the Apple Store One On One session in a prior attempt to fix this problem but obviously it did not work. I'd like to try it one more time with the drumkit connected. I did see a screen at one point which allowed me to select the inputs from the Focusrite but I could never find it again. I don't think it was a Garageband menu but somewhere else, maybe during the driver or software install for the Focusrite. I would love to get back to that screen again and take a hard look at it.

  • Live Monitoring and Recording for VPN Remote CAD Agents in UCCX

    Dear all,
    We have deployed UCCX 5.0(2) for one of our customers.
    Silent Monitoring and Recording are working fine for local agents.
    We have deployed new Remote agents using IP Communicator and Cisco VPN on their PC. Everything is working fine but could not monitor or record them.
    We have made site-to-site VPN using a PIX and give these agents Hard Phones 7942. Everything is working fine but could not monitor or record them.
    We also installed WFO QM client on their PCs in order to record calls but no way !
    Is there any way that we can use in order to make these agents silently monitored and recorded?
    Thanks for all.

    good afternoon,
    I am not a senior guy but we experienced the same issues with monitoring users at home on VPN. After some trouble shooting I found that most users are on wireless and when I had them plug in with a cable we could hear their calls and record fine with no issues. Though, the agents preferred to be on wireless, of course! the senior engineer did mention something about changing the Codec and utilizing some DSP resources.
    MM

  • CUCCX 8.0 - Call monitoring and recording

    Hello,
         I've worked with desktop-side monitoring and recording on various versions fo CUCCX in the past and have come to the point where this particular solution is not practicle anymore (we would need cordinate with the desktop group to install Cisco-approved NICs, and yes I am aware that there is a workaround but it doesn't work on NICs that do not support promiscuous mode.)
         CUCCX supports a server-side method as well, but I have no experience in it and would like to find a how-to document.  Would it work in a mixed network environment?  Any pointers would be helpful.

    Hi
    In my experience the 'lack of support for promiscuous mode' NICs is vastly overstated. I've not come accross a single NIC that doesn't work. I suspect that document was written back when NICs were based on valves or something.
    Typically the main issues are simple config errors - not doing span-to-pc-port, not daisy chaining PCs, etc.(And on v8.0+ it's usually due to the services falling over, which will ruin things for you whether you use CAD or server-side monitoring!)
    RE: server side monitoring - I've worked on some fairly large SPAN based deployments. UCCX is pretty agnostic, you just need to make sure it sees each conversation (and sees each one only once!) using whatever SPAN config you can. It's more a question of how handy you are with networking than anything specific to UCCX.
    Regards
    Aaron

  • Monitoring and recording IPCommunicator

    hi, what do i need to enable to monitor and record an agent that uses an IP Communicator? thanks!

    Hi,
    Here is the doc to configure Desktop monitoring and recording:
    In CIPC while running postinstall select the NIC adaptor of the PC:
    http://www.cisco.com/en/US/customer/products/sw/custcosw/ps1846/products_tech_note09186a008075025a.shtml
    HTH

  • Monitoring and recording feature not working in UCCX

    Hi,
    The recording and monitoring option is not working in the new UCCX setup I have installed.I have configured following things for desktop monitoring as per the document
    1)Checked that IP Phones are diasy chained and speakers of Supervisor's PC is working,NIC card of agent's and supervisor desktops are compatible
    2)In web CDA P phones to be monitored have been configured
    3)In CCM configured the phone for "Span to PC port" as enabled also configured "Advertise G.722 codec" as disabled
    4)Ran postinstall.exe on agents system and checked if correct NIC adapter is being used for monitoring
    5)Checked the NIC binding order in UCCX server and that is correct
    I noticed one thing that "services"  in both CAD and CSD are showing as "partial services" and they are monitoring and recording services only.Hence is this problem related to these services? How do i correct the recording and monitoring issue?
    Regards
    Amit

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin-top:0in;
    mso-para-margin-right:0in;
    mso-para-margin-bottom:10.0pt;
    mso-para-margin-left:0in;
    line-height:115%;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    I would first recycle the VOIP Monitoring Service on both node if this is HA.  This will not affect calls or call processing.
    In addition, you stated you ran post install on the clients desktop but have you ran post install on the server itself?
    In the desktop Administrator, what server is selected to be the default VOIP Monitor server?
    Jason M. Hutchinson

  • Monitoring and recording using my audio interface

    I am new to the logic express program. When I try to record with my audio interface (whether mic or instrument), do I always have to go to the "Device Input" settings and swithc the input to my interface? Even when I do that, the bars move indicating sound, but I cant hear it...dont know what I am doing wrong?
    So basically, right now, I record without being able to monitor, then when I want to hear it, I have to switch the device input back from the interface to the default device?
    It seems I am making this harder than it is.
    Thanks for the help.

    I am having the same problem (using a presonus firepod). Tried the aggregate solution but it is not working.
    Steps I took: Aggregate Device Editor > selected firepod and built-in output. Then in Audio Midi setup selected aggregate device as default input. In Logic Ex 8, preferences>audio>enabled core audio and selected aggregate device as the driver. Created a new track, tried using input monitoring and the record button. I can see the levels go up and down, so there is signal, but no sound for me to hear. The inputs and outputs for the track are input 1 outputs 1&2.
    So am I doing something wrong?
    Thanks guys.

  • Monitoring and recording problem with midi vs audio firewire

    I'm trying to record my Roland synth via Inspire firewire box into Logic express. I'm able to record and monitor thru the output of the inspire box. However If I'm using firewire, I can't hear other midi file tracks and vice versa. I keep switching input and output sources in the control settings but it seems like I either have to use all midi tracks or all audio tracks. Same situation with playback. I know this is wrong but am totally stumped. Any advice would by awesome.

    Dave, You might need an external DAW to do this, I got it working and I'm an idiot. There is only one I/O for logic and if you use it for the audio recording it's not available for the sounds you want to have coming out of logic. I have Roland Edirol UA-25USB2 and it works like a charm, If I understand what I did correctly, the sound and MIDI messages are routed via an Aggregate Device in the audio/MIDI set-up [you configure the device in the audio half] to the Edirol, and there are many extra functions to choose from-I avoid the 3.5mm audio out headphone plug by routing audio out through the DAW Edirol-much better sound quality than the mini stereo jack.

  • Monitor and record server performance

    Hi all.
    This is not really Arch related but a general question. I have a web server that has services crashing. I think it may be due to low mem. Is there any software or some method that would allow me to monitor/log server stats/performance and then see a graph over time.
    My hope is to be able to see if services fail due to mem outages, or some other reason. I would also like to know better what my peak times are.
    Any suggestions are greatly welcome.
    Thanks alls for your input
    Cheers,
    P.

    What is the best way to uninstall and reinstall the Focusrite MIDI interface driver. And to uninstall and reinstall the Subtlesoft Midipipe (which is required to get the correct mapping for a Yamaha drumkit)? This was done for me at the Apple Store One On One session in a prior attempt to fix this problem but obviously it did not work. I'd like to try it one more time with the drumkit connected. I did see a screen at one point which allowed me to select the inputs from the Focusrite but I could never find it again. I don't think it was a Garageband menu but somewhere else, maybe during the driver or software install for the Focusrite. I would love to get back to that screen again and take a hard look at it.

  • Silent monitoring and recording

    When a supervisor or agent presses the record button they get an error "error received from recording service. More information in log file". I have attached the log file, anyone have this before?

    Have you tried doing a resync?  That option is also under CDA.  When you expand Service Configuration, you will see Synchronize Directory Services as an option.  Try resyncing and see if that resolves the issue.

  • Buttons under source and record monitors not working

    For some odd reason, the buttons under the source and record monitors are not working in Premiere. This is a new install, and I'm relatively new to Windows so I hope it is something obvious. Buttons in other CC apps work fine. Any ideas out there?
    Windows 7
    2 x 10 core CPU (40 virtual)
    64 GB Ram
    nVidia Titan
    Decklink 4K
    Latest Premiere CC build
    Wacom Tablet

    Yes, actually. I unplugged the Wacom, uninstalled the drivers and restarted. Problem still there. Other ideas?
    Chris
    =========================================
    Edited by moderator to remove personal information

  • Silent Monitor and Call record with voice vlan

    We are pretty new to CCX, and want to get silent monitor and call recording working. I've read a bunch of troubleshooting docs, and a bunch of the discussions here, but I am still unable to get it to work the way that I want.
    Heres the setup. The phones are all set to the recommended settings, and the agent pc is plugged into the phone. The data vlan is 111 and the voice vlan is 222. When I run the nicq prog on the agent pc, it can not find the phone, but I can enter the ip in , and it sees the phone. The supervisor laptop can not monitor or record.
    If I change the voice vlan to 111, nicq still can not find the phone, but the supervisor can record and monitor with no problem. Is is an issue with 802.1q and perhaps my nics do not support it?
    CCX Ver:
    8.5.1.11004-25

    Hi
    It could be, but it's pretty rare.
    Have you enabled 'PC Port Voice VLAN Access' and 'SPAN to PC Port' on the phone?
    Have you tried alternate PCs/laptops on the back of that phone?
    Aaron

  • Problem with Adobe Audition 2.0 and recording from a 1212m.

    I bought a brand new machine and have be configuring it all week. Everything has been going well, except getting Adobe Audition 2.0 (the new version) to “hear” sound from the 1212m.
    The intel 975 motherboard has an integrated HD sound system already on board and I have been able to get adobe audition to recognize it and record from it. This is what I have Windows XP Pro set to as my default sound card.
    I installed the 1212m and I have gotten my monitors to work by using the XLR jacks on the monitors to the ¼ inch jacks on the 1212m using a VST (NI’s Kontakt 2) as the audio source. So it works.
    What I can’t seem to get to work is getting Adobe Audition to “hear” the sound coming from the 1212m.
    Patchmix seems to be working ok. The audio bars jump each time I hit a note on the keyboard.
    I have configured Audition by going to Audio Hardware Setup and setting it to EMU ASIO and tried every combination of INPUT and OUTPUT, but when I hit the Record button in Audition it just flat lines..
    I was hoping that once the audio made it from the VST though the 1212m and out to the speakers, that getting Audition to record it would be easy, but that hasn’t been the case.
    The Intel 955 Extreme Edition and the 975 motherboard are brand new and I’m worried that being on the bleeding edge of technology, that one of the drivers isn’t working correctly and causing me hours of debugging a problem that is unworkable from my end.
    Hopefully the problem is just some small stupid thing that I’m doing or failing to do (like normal).
    Any ideas would be helpful.
    thanks

    I'm just saving it into a file in "My documents" on the internal hard drive. It's a computer in the office which has been used my other people before me and I have my own file which I was always able to save Adobe sound files into before, so I don't think it's anything to do with me not being allowed or read-only.
    I've also been trying to save it onto USB hard drives. This works when I save it under a different name, but not when I'm just trying to update a file i've been working on. Basically I have to create a new file everytime I add something, so like "myaudit1", "myaudit2", "myaudit3" etc etc, even though it's the same piece of work just updated.
    Hope that makes sense!

  • MacBook Pro performance issues w/2nd monitor and FCP7

    I have this MacBook Pro bought brand-new in January 2010:
      Model Name: MacBook Pro
      Model Identifier: MacBookPro5,2
      Processor Name: Intel Core 2 Duo
      Processor Speed: 3.06 GHz
      Number Of Processors: 1
      Total Number Of Cores: 2
      L2 Cache: 6 MB
      Memory: 8 GB
      Bus Speed: 1.07 GHz
    and until today had never attached a second monitor to it. Today I hooked up my Samsung 24" to do some dual screen editing in Final Cut 7.0.3. I was unable to play back my video at full speed in the second monitor, and after a few seconds of skippy playback I'd get that error message about unable to play back video at full speed and to check my RT settings. I was using a Mini DisplayPort to DVI adapter. My computer has no issues playing the video in the laptop's monitor at any resolution and any quality settings (I've never changed the RT settings or anything else in the menu ever but I tried every combination this time). I then tried using my TV as a 2nd monitor with an HDMI adapter. Same performance issues. I then tried my friend's newer 13" MBP 8,1 and it performed flawlessly with the same project & footage. I feel like my $3,000 computer should outperform a $1,200 one even if mine is a year and a half older. Any advice?
    Chris

    Wow, you posted this perfectly to coincide with an identical problem, albeit using Logic Pro 9.1.5 rather than FCP.
    Last week, I purchased a 23" external monitor to use alongside my "flagship" 2011 15" hi-res, 2.3 i7 Macbook Pro with 8Gb of RAM.
    It is connected via a mini-DVI to D-sub analog (not that that should matter?) and all appeared fine.
    The first issue I had was with my MBP's fan now running CONSTANTLY, when I have the second monitor attached. Even when the machine is completely idle.
    When using the machine to record audio, this is a fairly hefty problem and not something I had anticipated - indeed why would I anticipate such a thing?
    What is far, far worse though is that over the last few days I have had repeated problems with performance drop-outs and errors in Logic and I have trying to fathom out why. Realising that the only major system change made, was the above monitor connection, I ran some tests.
    I restarted my MBP, no other apps were running and with my new 23" monitor attached acting as main display with MBP built in display on as secondary
    I loaded up a fairly demanding Logic project which was hitting 40% to 60% CPU usage when using the built in MBP display last week
    I ran activity monitor and had CPU usage history open
    The above project now repeatedly overloads and playback halts in a given 8 bar section - with CPU at 80% most of the time
    I disconnected the external display, no shut down, I just let the machine switch to the built in 15".
    Started the same project, the same 8 bar section and hey presto - CPU usage back down to 40% to 60%
    The above was reflected in the CPU usage history with the graph showing CPU use down by about a half, when running this Logic project WITHOUT the external display.
    There is a very useful benchmark Logic project that has been used as a test by many users to gauge Logic performance on given Apple hardware.
    The project has about 100 tracks pre-configured with CPU intensive plugins, designed to tax the CPU.
    The idea is that you load up the project with tracks muted, press play and then unmute the tracks steadily until Logic us unable to play contiunously because of a system performance error.
    On my MBP, with the external monitor NOT attached, I can play back around 50 of the audio tracks in this benchmark project.
    With the monitor attached, I can get about 22 tracks playing.... which is actually a far worse a performance drop (-50% I think!?) than with the first example!
    I did also try with just the external monitor attached and not the MBP display and performance was about 10% better than with dual monitors - so still extremely poor, to say the least.
    This machine is the flagship MBP and has a dedicated AMD Radeon HD6750 GPU which should take care of most if not ALL graphics processing - I mean it's capable of running some pretty demanding games!
    Putting aside the issue of constant fan noise, there is no reason AT ALL, why using an external monitor should tax the i7 CPU this way - it's not as though Logic is graphically demanding... far from it.
    I am on 10.6.8, Logic 9.1.5, all apps up to date via "Software Update".
    I will of course, be contacting Apple...

Maybe you are looking for