CRS with 10GE port

Hi ,
As of now we use 1 port 10GE card only (Cisco 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA) in our CRS connects to Core backbone.
We might need 10GE for access now to provide 10GE to PE ( pure ethernet not any optical technology).
I was trying to find out the line card support more 10GE port density for this purpose. Cisco support 8 port 10GE module but that is not SPA rather normal Ethernet card (Cisco CRS-1 8-Port 10 Gigabit Ethernet Interface Module). How is it diff than SPA to use for PE-P - MPLS link includes LSP, Qos etc feature....
Can I use this 8 port 10GE card for the above puropse ? Important thing there should not be any major limitation
Regards,
Chintan

Hello Chintan,
in other platforms we are used to see more features or different features supported on SPA modules.
the datasheet of the 8 TenGiga
http://www.cisco.com/en/US/prod/collateral/routers/ps5763/ps5862/product_data_sheet09186a008022d5e9.html
About SW it just says:
Software Compatibility
Cisco IOS XR Software Release 3.0 or later
the list of features for SPA GE and 10GE
http://www.cisco.com/en/US/prod/collateral/modules/ps6267/product_data_sheet0900aecd804d884d_ps5763_Products_Data_Sheet.html
There is some more detail.
then I've gone to
www.cisco.com/go/crs
but I've found no useful info
Looking at the configuration guides, the QoS for example I didn't find any distinction about the linecards
http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.7/qos/configuration/guide/qc37fab.html#wp998930
Ask to your cisco account manager or even open a TAC service request to request info to be sure.
Hope to help
Giuseppe

Similar Messages

DFM@LMS4.0.1: lots of Voltage meassage from 10GE ports

Hello,
We got suddenly a lot of Voltage faults in DFM from 10GE ports at our VSS Core. Communication is not affected.
All other devices show voltage in a valid range and the VSS before this night as well.
An "shut / no shut" of the interface doesnt help, CLI confirms the problem, see below.
What does it mean? What can we do that this faults disappears?
fli_rie_core254#sh interfaces transceiver switch 1
Transceiver monitoring is disabled for all interfaces.
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
                                         Optical   Optical
            Temperature Voltage Current   Tx Power Rx Power
Port        (Celsius)    (Volts) (mA)      (dBm)     (dBm)
Te1/1/1       33.8       0.00      45.7 --   -1.4     -32.2 --
Te1/1/2       32.3       0.00      42.3 --   -1.5      -1.2
Te1/1/3       31.5       0.00      42.0 --   -1.5      -2.8
Te1/1/4       28.7       0.00      43.3 --   -1.4      -2.7
Te1/1/5       29.7       0.00      43.0 --   -1.5      -2.7
Te1/1/6       28.4       0.00      45.8 --   -1.4      -4.9
Te1/1/8       26.2       0.00      43.2 --   -1.4     -37.0 --
Te1/2/1       30.2       0.00      41.3 --   -2.1     -33.0 --
thx for help in advance,
Steffen

No,
Have your question something to do with the initiated discussion?
Von: cassiefang
Gesendet: Freitag, 17. Juni 2011 09:06
An: Neuser, Steffen
Betreff: New message: "[email protected]: lots of Voltage meassage from 10GE ports"
Cisco Support Community
Re: [email protected]: lots of Voltage meassage from 10GE ports
created by Shuo Fang in Network Management - View the full discussion

How can i connect apple hd cinema display 30-inch DVI to my new notebook with HDMI port

I have ask this question in the local shop but they could not answer me - how can i connect apple hd cinema display 30-inch DVI to my new notebook with HDMI port

I wasn't sure how the whole thing would have work but it seems thunderbolt also acts like mini display port. Thats sweet. I can now haply continue using my 30 inch apple display.
Thanks.

How to connect MacBook Pro 17" Mountain Lion with HDMI port on TV, Panasonic TC-P55ST50

Any experience with cables for connecting MacBook Pro 17" Mountain Lion with HDMI port on TV, Panasonic TC-P55ST50 (or similar)?

It depend upon the model (age) of you MBP. If you have a Thunderbolt or minidisplay port, then you will need a minidisplay/HDMI adapter.
eshop.macsales.com/item/NewerTech/CBLMDPHDMI/
Or you can get an all in one:
http://www.amazon.com/Cable-Matters-Premium-DisplayPort-Thunderbolt/dp/B004CADYD O/ref=sr_1_3?s=electronics&ie=UTF8&qid=1361985588&sr=1-3&keywords=minidisplay+hd mi
If you have an older mac with a DVI port, you will need something like this:
http://www.amazon.com/DVI-HDMI-Cable-6ft-Male-Male/dp/B0002CZHN6
Note that audio is supported via HDMI for MBPs 2010 and later. Earlier ones require tapping the audio output port.
Ciao.

Connecting Cinema Display with mini display port to macbook pro with thunderbolt port

I am trying to connect a 27" cinema display (2010) that has a mini display port cable out of the back, into my macbook pro (2013) with thunderbolt ports. The mini display port cord fits into the thunderbolt port on the Macbook Pro, however the macbook pro does not detect the cinema display and the cinema display does not have any picture on the screen. The USB plugs in fine and sound comes out, and I have the adapter for the magsafe to magsafe 2 and that works fine, it just the actual display. Any help would be appreciated!
Thanks!

Hello mmholt,
Welcome to Apple Support Communities.
It sounds like there’s no video on an Apple Cinema Display that’s connected to your MacBook Pro, and you’re wondering if the configuration is supported. It is supported, take a look at the article linked below for more information.
Thunderbolt ports and displays: Frequently asked questions (FAQ) - Apple Support
1. Can I connect a Mini DisplayPort monitor or monitor using a Mini DisplayPort adapter to a Thunderbolt port on my Thunderbolt-equipped Mac?
Yes. A Mini DisplayPort display or a display connecting with a Mini DisplayPort to VGA, DVI, or HDMI adapter will work just like it was connecting to a Mini DisplayPort connector when plugging in directly to the Thunderbolt connector on your Apple computer. Click here for more information on Mini DisplayPort connections and adapters.
Also, this article provides a lot of great information and troubleshooting tips that will resolve most issues related to video external displays.
Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
So long,
-Jason

How to connect the macbook with thunderbolt display 27" to TV with RGB port?

Hi,
I have the following equipments in hands:
1. Macbook PRO 15 inch with 1 thunderbolt port, OS is Mavericks 10.9.2
2. Apple Thunderbolt display 27" identical to this : http://www.apple.com/displays/
3. A Samsung TV with RGB port, & HDMI port.
I want all these displays ( macbook, Apple thunderbolt display & the Samsung Tv) connected at the same time, I had a trial to connect them using a minidispaly adapter to RGB port & HDMI port in the TV but it didnt worked.
Please help!
Thank you.

The Thunderbolt dock adds extra ports:
HDMI (up to 2560x1600 with the Elgato, 1920 x 1200 with the CalDigit)
3 USB 3
Ethernet
Audio in
Audio out
You could also use a Belkin Thunderbolt dock.
<http://www.belkin.com/us/p/P-F4U055/>
It includes a FireWire port, but no HDMI port, so would need a Mini DisplayPort to HDMI adapter (1920 x 1200 max) for the TV. This would use the second Thunderbolt port, so the Belkin dock has to be used with the port on the back of the Thunderbolt display, not between the computer and display.
If you don't need the extra ports, use a Thunderbolt hard drive (with two Thunderbolt ports)
<http://www.seagate.com/external-hard-drives/desktop-hard-drives/backup-plus-desk -mac-thunderbolt/>
This can be your Time Machine drive. Connect the Thunderbolt display to the computer, one port of the drive to the port on the back of the display, and a Mini DisplayPort to HDMI adapter to the second Thunderbolt port on the drive.
You will have three displays with differing resolutions, so mirroring is not going to fill each screen at full resolution.

Anyone else having trouble connecting MBP with thunderbolt port (TBp) and 27"iMac with mini display port (MDp)

I have a 27" Imac.i7 with mini displayport and MBP13 i5 with thunderbolt port. Some time ago I tried to connect my old MBP with miniDP to The 27"iMac I Failed so did the apple centre they refunded cable costs and said I'd be contacted by Cupertino. That was 9 months ago, now replaced MBP with 13 inch(**** I can use my iMac as display!). Does not work phoned Fast Lane very helpful guy called JIM emailed me some software/firmware update links. Still no display linking. One of the links was for a couple of updates for a TBp equiped 27" iMac mine is only MDp equiped. Failing to find any MDp updates in apple support. Anyone have any Ideas! My lad has a later 27"i5 he uses Xbox 360 no problem on his but it wont look at my MBP.
Beginning to feel like some of the kit that went with a fully loaded 5500 worked eventually. Computer and FM radio, Photography kit fine, video capture audio capture forget it. Too many crashes and resets made it impractical.

Check discussion from Linc Davis on this thread
Problems with Preview
Similarly preview hangs opening files

How to use the same OC4j server with different port number

How to use the same OC4j server with different port numbers..?
I have to OC4J installed on my machine on different hard disk drives....
I want to be able to run both the server simultaneously..?
is it possible ..it yes then how..?
for that i have changed the port number of one server...
but when i am trying to start the other server with different port number..it says that JVM -Bind already...
Is there any clues...?
Nilesh G

In the config directory:
default-web-site.xml: Change the port the HTTP listener listens on
jms.xml: Change the port the JMS service listens on
rmi.xml: Change the port the ORMI listener listens on.
Or, you can add another web-site.xml file, and deploy your applications to 1 server, and bind the web applications to the different web sites. This way you only have to deploy your applications to 1 place.
Rob
Oracle

Can I use a 2009 iMac as external display for 2007 macbook pro with DVI port only

I have a late 2009 imac with minidisplay port and a 2007 macbook pro with DVI port. I connected a mini diaplay port to DVI cable but all I get on the imac is a blank screen when I press F2. Can I use the imac this way?

I'm not sure if it works with DVI but your late 2009 must be a 27". Try Command-F2 or Copmmand-Fn-F2

HT1688 I have a honda civic with USB port which allows play back of my old iPhone 4 and 4s. With the new iPhone 5 the radio shows the phone is conected but does not show any music content.

I have a honda civic with USB port which allows play back of my old iPhone 4 and 4s. With the new iPhone 5 the radio shows the phone is conected but does not show any music content. Any Suggestions?

You should be syncing your contacts with an app on your computer or cloud service (iCloud, Gmail, Yahoo, etc), and not relying on a backup. If you haven't been doing this, start now and then restore your old backup. You will then be able to sync the new contacts back into the phone. However, you will lose all messages, etc newer thant the backup.

My iphone5 wont charge with usb port but works fine with wall plug... Infact computer. Doesn't recognizes the iphone

Battery not charging with usb port but works fine with wall plug.. So the prob is computer is not detecting the iphone5 . This problem started after upgrading to 6.1.3 version

Try to see what happens on another computer. If it works on another computer, the issue is not at the iPhone.

Please help me creating a new listener with different port#.

I have two instances in a server. both have different homes. I want to create a seperate listener for the second one i created.
But that is not happening.
here i tried to give name from LISTENER TO LISTENER1 & Port# from 1521 to 1524.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /apps2/oracle)
(PROGRAM = extproc)
LISTENER1 =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = aixth53)(PORT = 1524))
When I check lsnrctl status with LISTENER1 , it still shows the other instance home with port#: 1521
Please help me creating a new listener with different port#.
Thanks,

marist89 wrote:
sb92075 wrote:
marist89 wrote:
sybrand_b wrote:
The listener is a broker only and doesn't play any role in normal communications.
It just forks a process or a thread, and that's it.And the listener is a single point of failure. Listener goes down, you can't connect to the db. That's why you need two listeners.If listener one goes down, then listener two goes down for exact same reason since it is a single executable file.I'm not playing tit-for-tat with you. Fact is, there are situations where people who are not you might want to use more than one listener.Some folks might want to jab a sharp pencil into their eye, too.
Just because you can do something, it does not necessarily mean it should be done.

Trying to install WSUS role on Windows Server 2012 R2 using dedicated SQL Instance with static port on remote SQL Server 2012 SP1 CU7 on Windows Server 2012 R2.

I am trying to install WSUS role on Windows Server 2012 R2 using dedicated SQL Instance with static port on remote SQL Server 2012 SP1 CU7 on Windows Server 2012 R2.
It verifies the connection and then throws the error:
The request to add or remove features on the specified server failed. The operation cannot be completed, because the server you specified requires a restart.
WSUS Server : Windows Server 2012 R2
Remote SQL Server: 2012 SP1 CU7 hosted on Windows Server 2012 R2
Please let me know if anyone has experienced this issue.

We were trying to install WSUS role on Windows Server 2012 R2 using dedicated SQL Instance with static port on remote SQL Server 2012 SP1 CU7 on Windows Server 2012 R2.
It verifies the connection and then throws the error:
The request to add or remove features on the specified server failed. The operation cannot be completed, because the server you specified requires a restart.
Same error even after rebooting the server multiple times.
WSUS Server : Windows Server Standard2012 R2
Remote SQL Server: Windows Server 2012 SP1 CU7 hosted on Windows Server 2012 R2
Event ID 7000:
The Windows Internal Database service failed to start due to the following error:
The service did not start due to a logon failure.
Event ID 7041
The MSSQL$MICROSOFT##WID service was unable to log on as NT SERVICE\MSSQL$MICROSOFT##WID with the currently configured password due to the following error:
Logon failure: the user has not been granted the requested logon type at this computer.
Service: MSSQL$MICROSOFT##WID
Domain and account: NT SERVICE\MSSQL$MICROSOFT##WID
This service account does not have the required user right "Log on as a service."
User Action
Assign "Log on as a service" to the service account on this computer. You can use Local Security Settings (Secpol.msc) to do this. If this computer is a node in a cluster, check that this user
right is assigned to the Cluster service account on all nodes in the cluster.
If you have already assigned this user right to the service account, and the user right appears to be removed, check with your domain administrator to find out if a Group Policy object associated
with this node might be removing the right.
I found following article:
"MSSQL$MICROSOFT##WID service was unable to log on as NT SERVICE\MSSQL$MICROSOFT##WID" error when you install WID in Windows Server 2012
http://support.microsoft.com/kb/2832204/en-us
To work around the issue, use one of the following methods:
Assign the Log on as a service user right to NT SERVICE\ALL SERVICES in the GPO that defines the user right.
Exclude the computer from the GPO that defines the user right.
We moved the SCCM server to OU where no policies were getting applied and then applied the new GPO to that OU. Restarted the server and we were able to install WSUS role.
Regards
PR

How do I setup a DNS record to point to an internal IP with a port.

I am trying to setup a DNS entry on my AD server to point to a web sever that I have setup to run certain services. All of these services run through IIS on port 82 for example service A is internally 192.168.0.1:82/info/login and service B is 192.168.0.1:82/tech/login.
I am trying to give these services easy to use names like for example info.mycompany.com and tech.mycompany.com so that it is easy to access for the employees but I am obviously missing something because I have had no luck setting up anything. My
company is still using SBS 2003 as it's AD and DNS server so I am working with flint and bear skin here.
I am also trying to do the same thing for the external access to these services but where as I have the internal address for these services I have the external static IP. When using the external IP with the port from outside the network everything
works fine but I would like for it to to have a simple name identical to the internal names but accessible from the outside. I frankly feel out of my depth on both of these issues and I would really appreciate any help that can be lent. Thank you.

You cant set a dns record (that would be used by a browser) to point to an ip and port, srv records can but that requires the application to look them up.
To have info.mycompany.com point to 192.168.0.1:82/info/login you
would add a cname or A record to the dns pointing to that IP, then in IIS you would assign that dns name to the host headers. Also in IIS you would need to use
URL rewrite plugin with this you would setup a redirect for that host header {HTTP_HOST} to point to that link.

IMac 27" with display-port pc

Hello all!
I'm thinking about buying a used iMac 27" with the following specs:
Intel Core 2 Duo
iMac10,1
3,06 GHz
4 GB
I'm guessing this is the late 2009 model?
I really want to use this as a monitor for a new desktop I'm building. My question is; will it work with every pc that has graphics card with display-port ?
Many thanks in advance!
Message was edited by: iTim

Yes, the 10,1 is a late 2009 model. If it will work depends on whether the pc graphics card will supply Mini DisplayPort compliant signals.
Here is some information on using the 27" iMac in Target Display mode:
http://support.apple.com/kb/HT3924
Hope this helps.
Message was edited by: captfred

CRS with 10GE port

Similar Messages

Maybe you are looking for