Cryptic Xserve LOM error email

Hi everyone,
An early 2008 Intel Xserve that I administer for a school (I'm a volunteer), sent me this cryptic email at 4.13am local time. I'm not onsite at the moment and I am yet to set up a VPN tunnel into the network, so I can't get any more information from Server Monitor. I asked someone at the school to check if the room that we have it in felt hot, but they said that it was fine.
Does anyone know what is going on here?
* BMC E-Mail Alert, version 1.00 *
SEL Record ID: 1E2C
Time: Wed Mar 5 17:13:13 2008
Sensor: PSU1 Fan Out
Record Type: System Event Record
Owner: BMC
Channel Number: 0
LUN: 0
Sensor Number: 3Ch
Sensor Type: Fan (analog)
Event: Assertion
Mfg ID:
Hex Data Bytes: 50 00 08
Thanks for your help,
Alex

Did you get any resolution? I just got off the phone to Apple, they have suggested that I reset the LOM by disconnecting the power completely for a minute or so. The guy there also suggested that I try running leaving Server Monitor running on the Xserve so that when one of these assertions is triggered, it catches it. Unfortunately, I probably won't be onsite for a week weeks and so I can't do reset the LOM and at the moment, Server Monitor, when run locally refuses to connect to the LOM. So I can't test either of those options.
He also mentioned that it might be a UPS related issue. We have ours hooked up via USB to an MGE UPS, what about you?
Have you done anything that has fixed the problem? Or made it worse?

Similar Messages

Error Emails from BPM Process Administration Console

I am able to send error email to a single e-mail Id after configuring it in BPM Process Administrator(Engine-Networking tab).
How do I sent e-mail to multiple user?
I tried comma separated. It didnt work.
Anyone can help on this?
I get error something like below.....
will be notified. Original exception is: Illegal address Caused by: Illegal address java.io.IOException: Illegal address at fuego.io.SMTPClient.sendMail(SMTPClient.java:323) at fuego.io.SMTPClient.sendMail(SMTPClient.java:341) at fuego.server.service.MailNotificationDispatcher.sendNow(MailNotificationDispatcher.java:157) at fuego.ejbengine.service.EJBMailNotificationDispatcher.send(EJBMailNotificationDispatcher.java:55) at fuego.server.service.ServerMailLogOutput.doOutput(ServerMailLogOutput.java:116) at fuego.log.LogOutput.output(LogOutput.java:187) at fuego.log.LogSystem$LogItemDispatcher.logItems(LogSystem.java:980) at fuego.log.LogSystem$LogItemDispatcher.run(LogSystem.java:863) Caused by: javax.mail.internet.AddressException: Illegal address in string
Edited by: sideeque on Feb 16, 2011 7:56 AM

Not the answer you wanted and sure you already thought of this, but try using a group email address inside the Process Admin email field.
Dan

Workflow Admin - Error Emails

Hi there,
I must admit I am much more of a techie than an "administrator" with regard to workflow and I probably have neglected some of the typical Workflow Admin tasks.
I wonder if you can help me, every Monday morning I get about 4000 emails from R/3 Production....all "workflow error emails", and as you can imagine this does get pretty irritating sometimes
I know we archive WORKITEM pretty often, were are all these "workitems in error"? Do I need to run RSWWERRE? Is there another report that I can run to safely kill all these "error workflows" so that I don't always get hundreds of emails?
Any help would be greatly appreciated
Lynton

Well yes, that is what I want to do...sweep them under the carpet
But in all honesty there MUST be an easy way to solve this issue, I cannot believe all Workflow admin's out there get all these streams of error emails each week.......
Anyway, I will have to look into it again sometime...
Have a good day
Lynton

Address for person contains error: email address missing

Hi,
I have included a position in the existing organization structure. A central person assigned to this position . In check tap page , it shows error "address for person contains error: email address missing"
Could anybody help to solve this
Tnanks

Hi,
You can try with BBP_BP_OM_INTEGRATE transaction.
Hope this helps.
Regards,
Vikas

Received delivery subsystem error email 25,000 plus times. Can delete easily from my mac but deleting from my inbox on my mac does not delete from inbox on my husband and my iphones. HELP

Received delivery subsystem error email 25,000 plus times. Can delete easily from my mac but deleting from my inbox on my mac does not delete from inbox on my husband and my verizon iphones. HELP

delete and re-add e-mail on iphone and it will update with whats current on the server

Error email

Hi
I would like to send an error email whenever the workflow encounters any errors during processing. Does anyone know how can this be done ?

In transaction SWDC_RUNTIME you can define a workflow administrator who will receive sap mails when workflows are in error. If you want these to become real emails, the user you define as admin should set-up an automatic forwarding rule in his SAP workplace (SBWP > Settings > Office settings tab automatic forwarding).
In the basic data of each workflow definition you can also define administrator. This one has priority over the first one (i.e. the generic wf admin is used only if there is no specific one).
Hope this helps.
Patrick

WRV54G - Internet Drops and recovers /w Error Emails

A little background on our problem, 4 - 10 times per day the internet will drop and recover 30 seconds later, we have tried different settings, the firmware is up to date.
Both the wireless and wired fail during this time.
We have voip and network traffic running through it. It is indiscriminate about when it drops.
Here are the error emails from this morning:
Email1:
Wed Aug 8 07:50:22 2007
rgpf_nat_config:753: WRV54GFW-CONF: NAT configuration failed Wed Aug 8 07:50:22 2007
rnat_config:315: WRV54GFW-CONF: RNAT configuration failed Wed Aug 8 07:50:22 2007
rnat_config:250: WRV54GFW-CONF: Error in RNAT configuration (Local Servers) Wed Aug 8 07:50:22 2007
ipnat_add_rule:693: WRV54GFW-CONF: Failed nat control (SIOCADNAT - File exists) Wed Aug 8 07:50:22 2007
Email2:
Wed Aug 8 09:34:08 2007
estream_write_efd:797: socket 6: failed write() Tue Dec 31 16:00:12 2002 TOD got new time 1186590841 Tue Dec 31 16:00:11 2002
rgpf_nat_config:753: WRV54GFW-CONF: NAT configuration failed Tue Dec 31 16:00:11 2002
rnat_config:315: WRV54GFW-CONF: RNAT configuration failed Tue Dec 31 16:00:11 2002
rnat_config:250: WRV54GFW-CONF: Error in RNAT configuration (Local Servers) Tue Dec 31 16:00:11 2002
ipnat_add_rule:693: WRV54GFW-CONF: Failed nat control (SIOCADNAT - File exists) Tue Dec 31 16:00:11 2002
Email3:
rg_system_full:275: spawned PID 76
Wed Aug 8 09:58:49 2007
rg_system_full:255: setoid eth0 10000006 ssid "xxxxxxx"
Message Edited by Chris3plsystems on 08-08-2007 10:31 AM

Oh well, ordered a SonicWall ... lack of responses certainly didn't help the matter.

Answer: Explaining cryptic iTunes Producer error messages

I ran into all kinds of cryptic errors when submitting a book to iBooks via the iTunes Producer program. It looks like Apple is using the Java program "epubcheck" and simply returning those errors to the user (not very user-friendly). I found explanations and solutions to many of the errors over at the epubcheck wiki (and even added one).
http://code.google.com/p/epubcheck/wiki/Errors
Just thought this may be useful for others as well.

I got a reply from iBookstore support that fixed me right up. My issue was not a JAVA issue. Here's what they sent:
You can make an update to your settings in iTunes Producer to avoid this issue.
1. Open iTunes Producer
2. From the iTunes Producer menu, open Preferences.
3. Click on the icon for Advanced settings at the right side of the screen.
4. Uncheck the box next to Signiant.
5. Close settings and reattempt your delivery.
You will be notified by email once Signiant is available again.
Once I did that, my book delivered on the first try. I'm fixed and thanks to Apple.
Rocketman

LOM Error Message

I have the Problem that sometimes all of our 10 XServe (Early 2009) send a Error Massege via Mail at the same time, that the connetion to the Server is lost. When i try to connect to the Server via Servermonitor after the Message, there is no Problem to connect.
What does this Massage exactly means?
Here the Error Message in German:
============================================================
Statuszusammenfassung
Benachrichtigungsgrund:
Verbindung zum Server verloren
Server:
IP-Adresse: 172.29.24.138
Name: 172.29.24.138
Art: Xserve3,1
An seit: 34 Tagen 19:54:57
OS-Version: Mac OS X Server 10.5.8 (9L34)
Prozessor: 2 x 2,66 GHz Quad-Core Intel Xeon
Speicher: 12 GB
Boot-ROM: XS31.0081.B06
Seriennummer: CK9170146HS
LOM-Version: 1.1.8
System-ID: Aus
Speicher:
Steckplatz 1: 2048 MB, Normal
Steckplatz 2: 2048 MB, Normal
Steckplatz 3: 2048 MB, Normal
Steckplatz 4: 2048 MB, Normal
Steckplatz 5: 2048 MB, Normal
Steckplatz 6: 2048 MB, Normal
Laufwerke:
Laufwerk 1: Normal
Laufwerk 2: Normal
Laufwerk 3: Normal
Netzteile:
Prozessor:
CPU A Leistung: 2.00 W, Normal
CPU A Kern: 0.95 V, Normal
CPU A E/A-Leistung: 14.00 W, Normal
CPU A E/A: 1.14 V, Normal
CPU A Speicher: 1.56 V, Normal
Processor 1:
CPU B Leistung: 1.00 W, Normal
CPU B Kern: 0.95 V, Normal
CPU B E/A-Leistung: 14.00 W, Normal
CPU B E/A: 1.14 V, Normal
CPU B Speicher: 1.55 V, Normal
Systemplatine:
Standby 3,3V: 3.28 V, Normal
Hauptast 3.3V: 3.28 V, Normal
Hauptast 12V: 12.10 V, Normal
E/A-Controller-Leistung: 12.00 W, Normal
PCIe-Steckplatz 1 Leistung: 0.00 W, Normal
PCIe-Steckplatz 2 Leistung: 4.00 W, Normal
Geschätzte Eingangsleistung: 208.00 W, Normal
GPU-Leistung: 3.00 W, Normal
Hauptast 5V: 4.98 V, Normal
Speichermodul:
CPU A DIMM-Leistung: 1.00 W, Normal
CPU B DIMM-Leistung: 1.00 W, Normal
DIMM VRM-Eingang: 12.10 V, Normal
Netzteil 1:
PS1 Standby 5V: 5.04 V, Normal
PS1 12V: 12.35 V, Normal
PS1 Leistung: 60.00 W, Normal
Netzteil 2:
PS2 Standby 5V: 5.04 V, Normal
PS2 12V: 12.35 V, Normal
PS2 Leistung: 64.00 W, Normal
Netzwerk:
en0: Normal
Netzwerk: Ein
Temperaturen:
Systemplatine:
PCIe-Steckplatz 1: 37 °C (99 °F), Normal
PCIe-Steckplatz 2: 36 °C (97 °F), Normal
E/A-Controller: 43 °C (109 °F), Normal
CPU A: 29 °C (84 °F), Normal
CPU B: 31 °C (88 °F), Normal
Rechter Eingang: 21 °C (70 °F), Normal
Linker Eingang: 22 °C (72 °F), Normal
GPU-Kern: 43 °C (109 °F), Normal
Speichermodul:
DIMM-Steckplatz A1: 27 °C (81 °F), Normal
DIMM-Steckplatz A2: 27 °C (81 °F), Normal
DIMM-Steckplatz A3: 27 °C (81 °F), Normal
Memory Module 1:
DIMM-Steckplatz B1: 27 °C (81 °F), Normal
DIMM-Steckplatz B2: 27 °C (81 °F), Normal
DIMM-Steckplatz B3: 27 °C (81 °F), Normal
Netzteil 1:
PS1 Entlüftung: 32 °C (90 °F), Normal
Lüfter:
Systemplatine:
Lüfter 1 Eingang: 5.888 U/min, Normal
Lüfter 1 Ausgang: 5.760 U/min, Normal
Lüfter 2 Eingang: 6.016 U/min, Normal
Lüfter 2 Ausgang: 5.760 U/min, Normal
Lüfter 3 Eingang: 5.888 U/min, Normal
Lüfter 3 Ausgang: 5.632 U/min, Normal
Lüfter 4 Eingang: 5.888 U/min, Normal
Lüfter 4 Ausgang: 5.760 U/min, Normal
System Board 1:
Lüfter 5 Eingang: 5.888 U/min, Normal
Lüfter 5 Ausgang: 5.760 U/min, Normal
Lüfter 6 Eingang: 5.888 U/min, Normal
Lüfter 6 Ausgang: 5.632 U/min, Normal
Lüfter 7 Eingang: 5.888 U/min, Normal
Lüfter 7 Ausgang: 5.632 U/min, Normal
Netzteil 1:
PS1 Out: 6.656 U/min, Normal
PS1 In: 6.784 U/min, Normal
Netzteil 2:
PS2 Out: 6.656 U/min, Normal
PS2 In: 6.528 U/min, Normal
Sicherheit:
Gehäuseöffnung: Nein
============================================================

Power glitches and network faults seem the most obvious choices for investigation.
Other faults wouldn't trigger in parallel.

Automated error email notification when outbound IDOC fails

Hi,
The requirement is that whenever the outbound IDOC of message type PAYEXT, basic type PEXR2002, fails, then email has to be trigerred to a group id.
I had suggested to write a report program that runs as a job. If the IDOC goes to error status then mail will be sent from this report. Client prefers it to be done through workflow.
There is a standard process code for outbound IDOC failure handling EDIO (we40). standard task 7989 has been assigned to this process code. I dont want to modify this standard task as I am not sure of impact.
Terminating event for this task is 'ERRORPROCESSCOMPLETD'.
I have developed the workflow that has trigerring event 'ERRORPROCESSCOMPLETD' and bound with the IDOC number. This will send mail to the group id with the IDOC details
Now issue is that, I am not sure if standard process EDIO will be trigerred automatically, or should we configure anywhere. Since this is standard outbound IDOC, I am not able to add the process code in partner profile.
Please give your inputs or any other alternate solution to send mail through workflow when outbound IDOC fails.
Thanks in advance.

Hi,
I guess in your outbound partner profile for PAYEXT. you need to add process code EDIO in message control TAb. WHich will cause to trigger the workflow which will send the notification.

Adobe AIR 4.0 (Release) "-useLegacyAOT no" has cryptic compile-abc error

Got a really cryptic error with the following dump:
MESSAGE: com.gbs.commands::PublishGameCommand - Compile Game Process |
[java] 0 compile-abc
0x0095d728 PrintStackTrace(void*) + 40
[java] 1 compile-abc
0x0095dba1 SignalHandler(int) + 449
[java] 2 libsystem_c.dylib 0x98aae8cb _sigtramp + 43
[java] 3 libsystem_c.dylib 0xffffffff _sigtramp + 1733629791
[java] 4 compile-abc
0x0017053d avmplus::TraitsBindings::findBindingAndDeclarer(avmplus::Multiname const&, avmplus::Traits*&) const + 77
[java] 5 compile-abc
0x00055de4 halfmoon::AbcBuilder::initStmt(unsigned int) + 180
[java] 6 compile-abc
0x00052209 halfmoon::AbcBuilder::visitInstr(unsigned char const*, avmplus::ActionBlockConstants::AbcOpcode, unsigned int, unsigned int, int) + 9017
[java] 7 compile-abc
0x0004f595 halfmoon::AbcBuilder::visitBlock(halfmoon::AbcBlock*) + 469
[java] 8 compile-abc
0x0004ed1f halfmoon::AbcBuilder::visitBlocks(nanojit::Seq<halfmoon::AbcBlock*>*) + 63
[java] 9 compile-abc
0x000c0a76 halfmoon::parseAbc(avmplus::MethodInfo*, halfmoon::Lattice*, halfmoon::InfoManager*, nanojit::Allocator&, halfmoon::AbcGraph*, avmplus::Toplevel*, avmplus::AbcEnv*, halfmoon::ProfiledInformation*, halfmoon::Context&) + 182
[java] 10 compile-abc
0x000c1788 halfmoon::JitWriter::writeEpilogue(avmplus::FrameState const*) + 216
[java] 11 compile-abc
0x00129d3b avmplus::NullWriter::writeEpilogue(avmplus::FrameState const*) + 27
[java] 12 compile-abc
0x00183829 avmplus::Verifier::verify(avmplus::CodeWriter*) + 1273
[java] 13 compile-abc
0x000053af compile_abc::CompilerCore::emitPoolToModule(compile_abc::PoolInfo&, compile_abc::LLVMModule*) + 927
[java] 14 compile-abc
0x00004a80 compile_abc::CompilerCore::compile() + 4496
[java] 15 compile-abc
0x0000363f compile_abc::CompilerCore::run(int, char**) + 1471
[java] 16 compile-abc
0x00005f62 main + 66
[java] 17 compile-abc
0x00002235 start + 53
[java] 18 compile-abc
0x00000009 start + 4294958601
[java] Stack dump:
[java] 0.
Program arguments: /Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/lib /aot/bin/compile-abc/compile-abc -mtriple=armv7-apple-ios -filetype=obj -sdk /Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/lib /aot/lib/avmglue.abc -fields /Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/lib /aot/lib/air-fields.arm-air.txt -O3 /Users/lavonwoods/MyDocuments/GameBuilder/Projects/GameBuilderStudio/Tutorials/SampleProj ects/HungryHeroTutorialProjects/Step14/HungryHeroDemo/release/AOTBuildOutput52276902646665 87172.tmp/ABCFiles/AOTBuildOutput-0000000000.abc
MESSAGE: com.gbs.commands::PublishGameCommand - Compile Game Process |
[java] Compilation failed while executing : compile-abc
MESSAGE: com.gbs.commands::PublishGameCommand - Compile Game Process |
[java] /var/folders/fq/4yn2qtns2wb361mv9pqy60dh0000gn/T/cmd2780040483899292323.tmp: line 2: 10766 Segmentation fault: 11 "/Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/li b/aot/bin/compile-abc/compile-abc" "-mtriple=armv7-apple-ios" "-filetype=obj" "-sdk" "/Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/li b/aot/lib/avmglue.abc" "-fields" "/Users/lavonwoods/MyDocuments/FlexResources/SDKs/AIR/GBS_Compiler/AIR_4.0/Mac/air_sdk/li b/aot/lib/air-fields.arm-air.txt" "-O3" "/Users/lavonwoods/MyDocuments/GameBuilder/Projects/GameBuilderStudio/Tutorials/SamplePro jects/HungryHeroTutorialProjects/Step14/HungryHeroDemo/release/AOTBuildOutput5227690264666 587172.tmp/ABCFiles/AOTBuildOutput-0000000000.abc"
Was compiling everything fine with AIR 3.8 before. Only added the "-useLegacyAOT no" flag and changed the default air sdk to 4.0 in the application descriptor. Any ideas on what this may be?

This may be related to this bug https://bugbase.adobe.com/index.cfm?event=selectBug&CFGRIDKEY=3694360

Broadcasting error email sending

Hallo to everyone,
i try to send a query by mail using broadcaster. My server was configurated for mail services.
System log says me "error n. 829"
What does it means? can anyone help me??

Hi,
you can also monitor sending Emails...have a look at the below link...
http://help.sap.com/saphelp_nw04/helpdata/en/44/5b2341144ba52fe10000000a155106/frameset.htm
you can also ask your basis team regarding the error...

Create error email if message fails

Hi We would like to implement a scenario where we can receive an email error message if one our messages fails somewhere during its processing.
Is there a way to do this in BPM?
Basically we dont want to have to keep checking the AdapterFramework or SXMB_MONI to see if everything is ok.
We would like to just have an email notifying us that something has failed.

Hi,
It is very much possible depends on the scenario.
First of all you need to find what type of error handling you need to do ?
Even for some of the runtime errors it is not required to have BPM, if you go with Alert Mechanism
Even you can do Alert Message thru email.
To add on -
http://help.sap.com/saphelp_nw04/helpdata/en/56/b46c3c8bb3d73ee10000000a114084/frameset.htm
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
Regards,
Moorthy

AIA error emails not going out

Hi All
We have setup a QA box and deployed the code. Now while testing found that AIA Error notifications are not being sent incase of remote/binding faults. The same setup was done on Dev box and it works fine.
1. Set the email driver properties from EM Console :
OutgoingMailServer :
OutgoingMailServerPort : 25
OutgoingMailServerSecurity : none
OutgoingDefaultFromAddress: [email protected]
2. In <AIAHome>/AIAMetaData/config/AIAConfigurationproperties file , below properties are set
<Property name="EH.INVOKE.NOTIFY">true</Property>
<Property name="FROM.EMAIL.ID">Email:[email protected]</Property>
<Property name="EH.DEFAULT.ACTOR.ROLE">AIAIntegrationAdmin</Property>
3. In http://<host>:<port>/sdpmessaging/userprefs-ui console add email Id to user AIAIntegrationAdmin. Login to this console with AIAIntegrationAdmin/welcome1
4. Upload the AIAConfigurationproperties file to MDS and Reload the configuration from AIA Console setup page. (http://<host>:<port>/AIA/faces/home.jspx)
Now step4 is where we had an issue in QA. I uploaded the file to MDS but for reloading the configuration tried logging into AIA Console page. Here it doesnt have any buttons for clicking on Setup.
Also found that the AIAApplication is down from admin console. When I try starting it, throws an error
weblogic.management.DeploymentException: [Deployer:149003]Unable to access application source information in '/opt/apps/Oracle/Middleware/user_projects/domains/aiarv_domain/servers/aiarv_server/stage/AIAApplication/AIAApplication.ear' for application 'AIAApplication'. The specific error is: [Deployer:149158]No application files exist at '/opt/apps/Oracle/Middleware/user_projects/domains/aiarv_domain/servers/aiarv_server/stage/AIAApplication/AIAApplication.ear'..
Errors were encountered while performing this operation.
If I try to manually copy the AIAApplication.ear from admin server location into above mentioned path and then start AIAApplication, it starts but after restarting server again same error occurs.
Is this an issue with AIA Installation on this server ? And are the AIAApplication and AIAConsole issues related?
Regards
Subhankar

Hi Gerhard
I had already set 'Workflow Notification Properties' to 'Email' . The problem for me was with the way I had updated the UpdateMetaDataDP.xml for loading the AIAConfigurationProperties.xml into MDS.
I had specified as below :
<fileset dir="${AIA_HOME}/AIAMetaData">
<include name="../aia_instances/instance_name/AIAMetaData/config/AIAConfigurationProperties.xml" />
</fileset>
I changed it to below and reloaded the config file. Now emails are going out fine.
<fileset dir="${AIA_HOME}/aia_instances/instance_name/AIAMetaData">
<include name="config/AIAConfigurationProperties.xml" />
</fileset>
I had one final question:
In the User messaging preference console (http://<host>:<port>/sdpmessaging/userprefs-ui) can we add a comma separated list of email ids to the user
AIAIntegrationAdmin ?
Regards
Subhankar

AIA error email : The composite instance link in the email doesn't work

The error messages raised through email contain the link to the composite instance which upon clicking is
supposed (after login) to show the composite instance in the EM. This link is not working for clustered environment whereas it works fine for non-clustered environment
(after submitting login credential the page is again redirected to login page)
Please let me know, if anyone knows the solution .
AIAEHNotification.xml resides in server path /u01/middleware/aia/instances/aia/AIAMetaData/config

Hi,
Verify that the link in your AIAEHNotification.xml is as under.
- soa_domain is the name of my domain, you can replace this with your domain name
- SOA_Cluster is the name of our SOA cluster
*http://<BIGIP hostname>/em/faces/ai/soa/messageFlow?target=/Farm_soa_domain/soa_domain/SOA_Cluster/#@#PROPS.{compositeName}#@#+[#@#PROPS.{compositeRevision}#@#]%26type=oracle_soa_composite%26soaContext=#@#PROPS.{compositeDN}#@#/#@#PROPS.{compositeInstanceID}#@#*
Also to receive better response with AIA product, please post your thread in the AIA forum.
Application Integration Architecture (AIA)
Regards,
Neeraj Sehgal

Cryptic Xserve LOM error email

Similar Messages

Maybe you are looking for