CS11_not show low level component

Please find my qn as below,
Ex, BOM
A Header Material
1 ->Child Material 1
2 ->Child Material 2
When I check for my Header material (A) in CS11 I found child material 2 assembly indication is missed out.
Then I found in material master for material (Child Material 2) selection method as 1 (Selection by Explosion date) then I change the selection method as 2 (Selection By production version).Now if I check in CS11 for my header material A I can able to view the assembly indication for Child Material 2.
Please explain to me the logic why we change the BOM selection method, then it will show the low level component in CS11.
Awaiting for your replies.

Dear Kumar,
Pl. refer this link for BOM selection logic.
http://help.sap.com/saphelp_47x200/helpdata/en/f4/7d2b0444af11d182b40000e829fbfe/frameset.htm
Pl. just try this, when the BOM selection method is 1.
CS11 - After entering your details, press vew icon next to execute icon and check the Multi- level in extend view.
It may work for you.
Madhava

Similar Messages

Member selection doesn't show lower levels

When you are using member selection, it only shows the top level, no members are shown at all
Any ideas?

What about the Essbase version?
The conflict comes in on the server. The Java API, since about v7.2, has been progressing towards using pure Java calls to the Essbase server. Earlier versions wrapped the C APIs on the server.
Until recently, there was a setting to force the Java API to revert to using the C-APIs. Generally, we adjusted this setting only when the Essbase version and the Java API version were not exactly the same (and sometimes even then if we saw anything that didn't behave as we thought it should.
The setting, olap.service.direct, is not in the 9.3.1 essbase.properties file. Further, the directory containing the C API files is no longer installed as part of the APS installation.
Is APS also 9.3.1? Do you see anything in your APS logs? Note that, by default, APS no longer logs information to standard out (where error messages are sometimes printed). I posted a blog entry just an hour ago that shows how to setup APS to log stdout. It is on my blog at http://timtows-hyperion-blog.blogspot.com/
Tim Tow
Oracle ACE
Applied OLAP, Inc

Will not print black. ink cartridge is new. also shows low black level with new cartridge.

HP Photosmart C6180 all-in-one. Will not print Black. Also shows low black ink on ink level. Cartridge is new and HP brand.
In printing colors, very light and has RED hue as there is no black. Also two other cartridges show low ink when all the cartridges have been replaced.

Hi there,
Download and run the print and scan doctor located here (amoung resolving some things automatically it can give us a better idea of what is going on with the printer). Give the steps outlined a shot and let us know the results.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

DMR Not showing materials of Lower level WBS

Hi,
I have multiple WBS under 1st level. It is working find with cost reporting. But when i create DMR with DP91, it shows materials attached with activity comes under 1st level WBS only. How can i bring materials of lower level WBS activity materials into DRM while triggering DP91 with Upper level WBS...?

Hi rajsekhar
But generally if you want to transfer the cost of the sub item to main item then you can check the box Cumulative cost in copy control VTFL . But your requirement is quite opposite .So you need to go to assign a New Reqt / Alt calc type to the cond type , telling that the header item cost which is not relevant for pricing has to be transferred to sub item .So you need to integrate with the ABAP'er to give inputs to him and giving our requirement also
Regards
Srinath

How to low level format Mega Stick 256?

i suspect that my mega stick has a defective point in memory because if i delete a song and then put some news in the stick, the drive recognizes the title of the new one but plays the old one!!!! the one that was deleted
example
i deleted depeche mode - song
later i copied in pantera - song
ehan i try to play pantera-song, it says that in the scrolling title on screen, but sounds depeche mode!!!!!!!!!
so now im trying to make a low level format in case something is screwed in my mega stick
By the way.........how much warranty gives MSI for mega sticks?

Thanks to all for the suggestions. I'm about to give up on it, although I will try the PowerMax software recommended by Michael Black.
And The hatter: Don't let this burn you on Neptune drives—one of my client offices has been using about 20 of them for the past couple of years now, on a daily basis, for large-scale imaging projects, and the little drives have been real champs. We're even using them to dual-boot both Intel- and PPC-based systems, and they've just been outstanding. Methinks the component failure probably cascaded down to the drive, and while yes, it *****, such things happen in any batch of components and I'd buy another Neptune today if I had the need for yet another external.
As for Matt Broughton: S.M.A.R.T. shows no problems when the drive is connected directly to the ATA bus. But then again, I've only run into a few drives that S.M.A.R.T. has ever reliably reported on—it's still a black art, to be sure. The WikiPedia article on S.M.A.R.T. goes into more detail about its pervasive flakiness.
For now, the drive has begun to beep about once every 2 seconds at boot. This lasts for about 30 seconds, after which the drive continues to spin but no further beeping is heard. The drive no longer shows up in Disk Utility, even as an unmounted drive/volume. So, I'll probably try it in a PC w/PowerMax just to say that I did, but beyond that, it's probably ready for disassembly as an example drive.
80 GB—sniffle…
Thanks again to all for your suggestions!
Take care,
MBJ

How to low-level format entire drive, including partition map?

Hi everyone,
I have an OWC-supplied, 80 GB, ATA hard drive (OWC Neptune), which originally shipped in an external, FireWire 400 case. The drive stopped working; disassembly of the case led to the discovery of a burned trace on the Oxford bridge. While the bare drive itself has no manufacturer name, its label style and model number listed on the drive clearly show it to be a Maxtor 6Y080L0, 80 GB.
Having removed the drive and installed it into a test Power Mac G4, the physical drive is recognized by Disk Utility (albeit with no partitions, mounted or otherwise). The drive emits "normal" power and spin-up sounds, with no clicking or other sounds that might normally indicate a failed drive. However, Disk Utility is unable to actually partition the drive—when attempted, the "Creating Partition" progress bar advances to about 1/8 of the way across, then moves no further (even if many hours are allowed to pass). Console reveals nothing as to what is stopping the format.
Moving further, I attempted to blow away the partition map with pdisk, but encountered several read errors in the partition map itself. I even went so far as to attempt to "build" a partition map, one partition at a time, based on the settings I found on an identical drive that is functioning properly. Although this seemed semi-successful, attempting to write the partition table again resulted in a couple of errors.
pdisk: Unable to write block 8 (Input/output error)
pdisk: Unable to write block 9 (Input/output error)
pdisk: Unable to write block 10 (Input/output error)
pdisk: Unable to write block 11 (Input/output error)
While it's entirely possible that the blown component on the FireWire bridge might have also taken out the drive, I'm not a big believer in coincidence and my thought is that the trace blew during an access of the partition map, corrupting it to the point that only a low-level format of that portion of the drive can potentially salvage it. There is no data on the hard drive I am worried about losing, but I'm not one to easily say "die" and so I'd like to be able to restore this drive to functionality, if at all possible.
So after setting the table for you here, my questions are as follows:
1. Is there any way to low-level format an entire drive that does not have a readable partition map? In essence, effectively returning the drive to something resembling an out-of-box, unformatted state? CLI is fine, and I'm even open to trying to throw the thing in a PC box, install Yellow Dog Linux so as to have GUI access to pdisk, etc.
2. Does anyone have any other suggestions for me regarding this matter?
Thanks much for the time,
MBJ

Thanks to all for the suggestions. I'm about to give up on it, although I will try the PowerMax software recommended by Michael Black.
And The hatter: Don't let this burn you on Neptune drives—one of my client offices has been using about 20 of them for the past couple of years now, on a daily basis, for large-scale imaging projects, and the little drives have been real champs. We're even using them to dual-boot both Intel- and PPC-based systems, and they've just been outstanding. Methinks the component failure probably cascaded down to the drive, and while yes, it *****, such things happen in any batch of components and I'd buy another Neptune today if I had the need for yet another external.
As for Matt Broughton: S.M.A.R.T. shows no problems when the drive is connected directly to the ATA bus. But then again, I've only run into a few drives that S.M.A.R.T. has ever reliably reported on—it's still a black art, to be sure. The WikiPedia article on S.M.A.R.T. goes into more detail about its pervasive flakiness.
For now, the drive has begun to beep about once every 2 seconds at boot. This lasts for about 30 seconds, after which the drive continues to spin but no further beeping is heard. The drive no longer shows up in Disk Utility, even as an unmounted drive/volume. So, I'll probably try it in a PC w/PowerMax just to say that I did, but beyond that, it's probably ready for disassembly as an example drive.
80 GB—sniffle…
Thanks again to all for your suggestions!
Take care,
MBJ

Collective Planned orders Scheduling for lower level orders with reference to the Superior order

Hi All,
Collective planned order scheduling.
I have been trying to reschedule the superior planned order and i was expecting the lower level planned orders to reschedule based on the superior planned order.
My problem is
when i try to reschedule the superior planned order the system is not rescheduling the lower level planned orders.
For example if i change the basic finish date of superior planned order as 30/09/2014 and reschedule the planned order it is only scheduling the header planned order and the lower level planned order is not scheduling.
Could some one tell me why this is not happenning at planned order level.
As the rescheduling of collective order will work at production order level but for some reason it is not happening at planned order level(as there is no option available to do so).
Please give your thoughts on this asap.
Mahee.

Hello Mahee
Please observe that your system is working as designed. Planned orders are scheduled independently, even when they are part of a network/collective order. Note 152319 explains the planned order scheduling in detail and it provides the following information:
* No scheduling of overall networks is executed although a directly manufactured component is assigned.
Note that no scheduling of the overall network is executed for planned orders. For the components requirements dates are determined. In order to cover them, planned orders are created in the next MRP run. Since the requirements are not managed using the exact time, the results of the planned order scheduling and of a scheduling of the overall network of the converted collective order can differ.
BR
Caetano

Need help in copying Invoice date to lower level item in Sales order report

Hello Experts,
I am debugging into one Sales order report.I need little bit help.The report is displaying Invoice Date for
Sales order Billing documents for Higher item in Bill of Material Structures.But as per user requirement,
I am supposed to show the Invoice date for lower level items also.The field for Higher level item is 'UEPOS'.
I want to copy the Invoice date for Higher level item to lower level item. Can you please guide me in the logic?
Thanking you in anticipation.
Best Regards,
Harish

Hi BreakPoint,
Thanks for the information.
I have applied the same way but it is showing only lower line items now.
Invoice dates for Higher level items are not there.
I am pasting the code here which I have applied.
Then you can give me more guidence.
This is to be done only for 'ZREP' sales orders.
if w_vbak-auart EQ 'ZREP' and w_vbak-uepos is not INITIAL.
                      read table t_final into w_final_ZREP with key vbeln = w_vbak-vbeln
                                                                    posnr = w_vbak-uepos.
                         w_final-erdat_i = w_final_ZREP-erdat_i.
                         else.
                if w_vbak-auart EQ 'ZREP' and w_vbak-uepos is INITIAL.
                  w_final-erdat_i = w_invdate.
                endif.
                endif.
Can you please sugest me changes here?
Best Regards,
Harish
Edited by: joshihaa on Jul 13, 2010 6:22 PM

Error Msg -A Low-level exception occurred in: Adobe Player

I have CS6 installed, all the latest patches, etc. It's been working fine for months.In the last week Pr is unable to playback all of my footage (Native 5D mark III h.246 and Canon xf305 footage). Whether it is on the timeline or in the source panel.
The Error message i get it this: A Low-level exception occurred in: Adobe Player (player).
Using Adobe CS 6.0.3
Windows 64 Bit 8 GBs RAM
Happens in new projects and old.
New timelines also affected, it appears.
Was not happening as recently as two days ago.
No changes made to the computer.
Only changes is that I have combined timeines (Imported) from one project to another.
Video shows yellow or Green.
I have rerendered the footage to show all green on timeline.
Only way around it is to reboot the computer, it comes back after a while. The problematic timelines work fine for a while, then this starts happening.
I deleted the media cache database folder after exiting Pr.
Didn't seem to change anything. I just got the error again. Things seem to be curiously messed up. I tried to render a sequence out to MXF. The headless crashed each time, (not totally unusual, but it couldn't complete even once). I also got an error message when I bypassed the Media Encoder and just went strait to rendering it out within Pro. It managed to continue to render it to MXF but when I got done and imported it into Pro, it didn't play the clip when I clicked on it.
The interesting thing to me is that to totally clear Adobe from RAM, I have to go into Task Manager and kill the process after exiting the program (in lieu of rebooting). So it's not closing properly, it appears. Once I kill the process and reopen the app, I can then play the sequence, for a while. It's very curious. Task manager also shows lots of RAM open, no memory leaks at work, nothing unusual. It appears, to be just choking on footage, sort of like it can't quite process the audio (like when you bring in new footage and it has to process that audio). What's happening is like it sees the audio at first when I bring it in at startup of the app, then loses it. If I exit without killing the Premiere process (or shutting down the machine), then it still exhibets the behavior on startup again.
So this project is large, for me. It is showing as 34 MBs. I have a wide variety of clips at play here, but only MXF Canon from the xf305 and MOV from the Canon 5D. The MXF are the default sequence(s) unless I shot nothing but MOV.
I have tried rendering the visualization, all green lines on top but that doesn't seem to fully help. It does play the footage for a while.
There are no special effects added, yet.
Is it worth re-installing Premiere? This has cost me the better part of a day screwing around with this.
Let me detail this again:
Premiere is installed on C There hundreds of GBs of storage avaialble there.
All project files are on F which is a RAID 1 array. It appears to be functioning normally. 800 GBs free space on 2TBs.
All Renders are taking out to an external drive like I always do. Lot s of space available there too.
Anyone have an idea how to fix this?

Is this any better? Cut and pasted plain text.
I have CS6 installed, all the latest patches, etc. It's been working fine for months.In the last week Pr is unable to playback all of my footage (Native 5D mark III h.246 and Canon xf305 footage). Whether it is on the timeline or in the source panel.
the Error message i get it this: A Low-level exception occurred in: Adobe Player (player).
Using Adobe CS 6.0.3
Windows 64 Bit 8 GBs RAM
Happens in new projects and old.
New timelines also affected, it appears.
Was not happening as recently as two days ago.
No changes made to the computer.
Only changes is that I have combined timeines (Imported) from one project to another.
Video shows yellow or Green.
I have rerendered the footage to show all green on timeline.
Only way around it is to reboot the computer, it comes back after a while. The problematic timelines work fine for a while, then this starts happening.
I deleted the media cache database folder after exiting Pr.
Didn't seem to change anything. I just got the error again. Things seem to be curiously messed up. I tried to render a sequence out to MXF. The headless crashed each time, (not totally unusual, but it couldn't complete even once). I also got an error message when I bypassed the Media Encoder and just went strait to rendering it out within Pro. It managed to continue to render it to MXF but when I got done and imported it into Pro, it didn't play the clip when I clicked on it.
The interesting thing to me is that to totally clear Adobe from RAM, I have to go into Task Manager and kill the process after exiting the program (in lieu of rebooting). So it's not closing properly, it appears. Once I kill the process and reopen the app, I can then play the sequence, for a while. It's very curious. Task manager also shows lots of RAM open, no memory leaks at work, nothing unusual. It appears, to be just choking on footage, sort of like it can't quite process the audio (like when you bring in new footage and it has to process that audio). What's happening is like it sees the audio at first when I bring it in at startup of the app, then loses it. If I exit without killing the Premiere process (or shutting down the machine), then it still exhibets the behavior on startup again.
So this project is large, for me. It is showing as 34 MBs. I have a wide variety of clips at play here, but only MXF Canon from the xf305 and MOV from the Canon 5D. The MXF are the default sequence(s) unless I shot nothing but MOV.
I have tried rendering the visualization, all green lines on top but that doesn't seem to fully help. It does play the footage for a while.
There are no special effects added, yet.
Is it worth re-installing Premiere? This has cost me the better part of a day screwing around with this.
Let me detail this again:
Premiere is installed on C There hundreds of GBs of storage avaialble there.
All project files are on F which is a RAID 1 array. It appears to be functioning normally. 800 GBs free space on 2TBs.
All Renders are taking out to an external drive like I always do. Lot s of space available there too.
Anyone have an idea how to fix this?

How can I get low level access to netstream using OSMF?

Hi
I'm trying to gain access to the low level netstream underneath the hood of OSMF so that I can access its netstream.info property for reading metrics.
I find that I am able to do this for MP4 videos but not for F4M dynamic streaming videos.
For MP4, I was successfully able to create a VideoElement that used a CustomNetLoader class which overrided the createNetStream method to return a netstream object.
However, for F4M, I have to use either the MediaFactory.createMediaElement(element) method or the F4MElement. The F4MElement does not allow a CustomNetLoader to be used and it seems to only accept a F4MLoader class.
Any advice on how I can access either the netstream object or the metrics of F4M videos?
Thanks

ok, I finally got access to the direct netstream object - someone from Akamai gave me the answer.
Seeing how I wasn't able to find this answer anywhere on Google, I'm going to post the solution here as there's no way I would have known this solution without someone who knew how to get direct access to the netsteam object in OSMF.
There's a hidden class that won't show up in the code hint called org.osmf.net.NetStreamLoadTrait that you have to import.
1) First, your media player playing controlling your MediaElement has to listen for a LoadEvent.LOAD_STATE_CHANGE event after you load the MediaElement into the media player
mediaPlayer.addEventListener(LoadEvent.LOAD_STATE_CHANGE, onLoadStateChange);
2) Upon LoadEvent.LOAD_STATE_CHANGE, check for a org.osmf.traits.LoadState.READY - you can only access the NetStream object when it is LoadState.READY or the netstream object will return as null.
private function onLoadStateChange(e:LoadEvent)
                              if(e.loadState == LoadState.READY)
3) Once the LoadState.READY is true, you can create a datatype of NetStreamLoadTrait and type cast it from a Load trait:
private function onLoadStateChange(e:LoadEvent)
if(e.loadState == LoadState.READY)
     var nsLoadTrait:NetStreamLoadTrait = mediaPlayer.media.getTrait(MediaTraitType.LOAD) as NetStreamLoadTrait;
4) Once you successfully type cast the Media Load Trait from your media into NetStreamLoadTrait, you can access the property netstream from the NetStreamLoadTrait object.
private function onLoadStateChange(e:LoadEvent)
if(e.loadState == LoadState.READY)
     var nsLoadTrait:NetStreamLoadTrait = mediaPlayer.media.getTrait(MediaTraitType.LOAD) as NetStreamLoadTrait;
     var ns:NetStream = nsLoadTrait.netStream;
Hope this helps someone out there.

Is it a bug or just a typo in Agilent 532XX Series\Public\Data\Low Level\Fetch Measurement (Single).vi?

Hi, All
I am using Agilent 532XX Series driver to read data from a frequency counter. In the low level subVi : \Public\Data\Low Level\Fetch Measurement (Single).vi, "Scan From String" is used to convert the data.
however, if I check the error of this function, it always show me a error with current format string "%.;%g;". after I changed it to "%;%g", I don't get the error anymore.
If anyone use this funtion, please check the error out of that fuction and see what you get.
Regards
CQ

I don't have the instrument, so I can't reproduce it completely, but I've done some research and if there is an error I don't think it's in the string conversion itself. I say this because:
From what I can gather, a typical output string would be the following: +4.27150000E-03
I took just a "scan from string" node and gave it that string as a string input and %.;%g; as the format specifier string. This yielded a numeric value of 0.0042715
So, as far as actually finding the root of the problem, there could be a few things going on. My first thought is some form corruption causing the data received to not be valid for conversion. There are two ways of testing this:
Open up a test panel in MAX and perform a loopback test, as described here: http://www.ni.com/white-paper/3450/en/#toc4
-or-
Install and open NI IO Trace and view the bus traffic as detailed here: http://digital.ni.com/public.nsf/allkb/282C5D41E2BA04F2862574BA007803B9
If the loopback tests works properly, go ahead and run the IO trace and post the results here.
Christopher S. | Applications Engineer
Certified LabVIEW Developer
"If in doubt... flat out." - Colin McRae

Updation of higher level item text to lower level item text

Hi All,
while creating sales order VA01 i need to pass the value of higher level item text to lower level item text
for that i read the text of the higher level item text using the fm read_text
and pass the text to the lower level items using save_text and commit_text
this coding works only when the lower order item text is empty
my queries are
1. if the lower level item having some text that text will be replaced by the higher level item text, that is happening but showing error that I/O error , how to solve this
2. while gone to VA02 and add one more item then also same error is happening how to solve this please help me.
regards
krishna

got the solution

Nodes with Only One Lower-Level Node = Hide

Hi everyone
Have anyone present this situation:
Iu2019ve a quey to report inventory aging. It has two hierarchies to show data. In Rows I have Major Markets and in Columns a date hierarchy to show aging Ex: from 0 to 8 months, 9+ and 13+. Of course here I have also value and volume.
Query reports all values for all major markets fine. When I filter one major market, letu2019s say France also brings detailed figures but when I add any drill down in rows all values goes to cero (0).
Te estrange is that if you swap drill down order with major markets or drill down by columns with the same characteristic figures come out again as usual.
I know this sounds like a SAP note but I have not been able to find it either.
Thanks a lot for your help, and of course points will be assignedu2026..
Ps. Important, this happen when option u201CNodes with Only One Lower-Level Node = Hideu201D (this is selected on purpose because there are some repeated nodes in major market hierarchy Ex. France u2013 France and if there is just one value under first node then means that only display of last one is necessary to avoid repeated values).

Solution we found is to remove flag "Do not display leaves for inner-nodes in the query", directly on the hierarchy.
Thanks

What exactly is a "low-level exception occurred in: ImporterFastMPEG?"

I've been importing several HDV video files (m2t files) from my Sony HDR-DR60 HDD unit into Premiere Pro CS6 on my Macbook Pro w/ Retina Display. I noticed that this error popped up for 3 files: "A low-level exception occurred in: ImporterFastMPEG (Importer)" What exactly is happening here? What does that mean? Those video files appeared with small "?" icons next to their names in the bin. I attempted to import them again, but I was either given the same error message or only the first few seconds of the file would import. For example, one file is 645MB and is a little over 3 minutes long. Now when I try to import this file, it shows as being only 19 seconds in length.
Now here's where it gets perplexing: I took that same file and fired up my decommisioned Windows PC with an old installation of Premiere Pro CS5.5, and it imported perfectly without a problem.
I found a very slow work-around where I converted the m2t file into an uncompressed Quicktime MOV, but I'd like to find out what the root cause is and why I'm getting this error for these few files. I've done a lot of shooting this week, and I haven't had a problem with any other files from my HDR-60.
So, is this a Mac/Apple problem, a Premiere CS6 problem, or are those particular files just randomly weird? Google searches have not yielded anything useful which is why I'm asking here.

You might go back to http://forums.adobe.com/community/premiere/premierepro_current
In the block under Ask a Question enter
low level exception
so you may read previous discussions
Be sure to click the See More Results at the bottom of the initial, short list

Concurrence of low level and semantic EventListener

Hello,
when in the following program [Cancel] is clicked right after program start, I don't mind that the low level FocusEvent is first processed. But I do wonder why
the ActionListener is not processed at all.
Only when [Cancel] is clicked a second time (meanwhile the caret is in the third textfield, where there is no FocusListener) the program exits.
Removing the comment slashes in the focusLost method is a solution to this problem. However, I did not find anything concerning this topic in the documentation. Does anybody know a page where I can find a rule on which listener eats which?
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
public class Cancel extends JFrame
{ JTextField tf1, tf2, tf3;
public Cancel()
{ setSize(300,300);
    setDefaultCloseOperation(WindowConstants.EXIT_ON_CLOSE);
    Container cp= getContentPane();
    cp.setLayout(null);
    tf1 = new JTextField(20);
    tf1.setBounds(50,50,200,20);
    tf1.addFocusListener(new FocusAdapter()
    { public void focusLost(FocusEvent e)
      { // if (!(e.getOppositeComponent() instanceof JButton))
     tf3.requestFocus();
    tf2 = new JTextField(20);
    tf2.setBounds(50,100,200,20);
    tf3 = new JTextField(20);
    tf3.setBounds(50,150,200,20);
    JButton b = new JButton("Cancel");
    b.setBounds(100,200,100,30);
    b.addActionListener(new ActionListener()
    { public void actionPerformed(ActionEvent evt)
      { System.out.println("Cancel");
     System.exit(0);
    cp.add(tf1);
    cp.add(tf2);
    cp.add(tf3);
    cp.add(b);
    setVisible(true);
public static void main(String arg[])
{ new Cancel();
}Regards
Joerg

I think the process must be
(1) Click on (above) Cancel
(2) Current focus is moved
(3) New focus is given
(4) Component recieves click
but in the code above there is
(2.5) focus moved to Text field
and this presumably cuts off the rest of the sequence. I'm not sure where in the depths of Swing this could be confirmed/refuted but since AbstractButton is only the reciever in this chain i'd doubt its there?
maybe java.awt.EventDispatchThread? or some kind of FocusManager?
the exact logic is probably distributed among lots of classes though :(
Frankly, if this behaviour is intentional, I don't
understand why.hm, if manually reassigning focus didn't take precedence to the user impliciting reassigning focus by clicking on components then it wouldn't have any point though (?)
asjf

CS11_not show low level component

Similar Messages

Maybe you are looking for