CS6 AFX Network Render Node - Can't enable non-royalty bearing mode.

I have found many many threads saying to place this text file in these locations:
To enable non-royalty bearing mode: Place a blank file named ae_render_only_node.txt into one of the following locations, depending on the user account type:
Install After Effects on the render-only machine.
Place a blank file named ae_render_only_node.txt into one of the following locations, depending on the user account type:
Mac locations:/Users/<username>/Documents//Users/Shared/Adobe/
Windows locations:C:\Users\<username>\DocumentsC:\Users\Public\Documents\Adobe
But, it's not working for me. I try to open AE render engine and it just tells me my trial is up. I've dropped that text file in just about every file you can imagine, even ones that probably don't need it.
What am I missing?
Windows 7 64-bit PC

>> Interesting. Just yesterday I updated Bridge on a Render Engine machine without causing a problem, but this is worth pursuing.
>>> I don't believe that it was the update that caused the problem, it didn't work prior to the update either. I updated and restarted per a recommendation I saw on a forum, in case this was a problem that was resolved with an update.
I also started dropping the ae_render.txt file in the appdata>roaming>adobe files, no luck! I've restarted the computer, and tried using the cntrl+alt+shift open trick. I get nothin.
>> Hmmm... I'll have to check with engineering, but it's possible the Render Engine mode doesn't read or write preferences. It has no need of them. So unless you'd have launched the full UI of AE at some point, the 12.0 folder might not exist. In any case, probably not worth pursuing for this problem, it was just one of the normal troubleshooting tricks.
>>> The 11.0 folder also was not replaced, because I can't get past the trial expiration screen.
>> If you uninstall and reinstall AE, does the problem continue?
>>> I was hoping to resolve without having to do that -- but I'll give it a go.
I'm getting the feeling that since I didn't put the .txt file in the proper location prior to my trial expiring, the software never even gets to the point that it can check for it.

Similar Messages

Adobe Encore CS6 cannot run in non-royalty serialized mode. The application needs to be serialized with a royalty bearing serial number

Adobe Encore CS6 cannot run in non-royalty serialized mode. The application needs to be serialized with a royalty bearing serial number.

This is an activation issue. its solution has changed over time. Assuming you have a cloud subscription, see this.
http://helpx.adobe.com/premiere-pro/kb/features-presets-missing-premiere-pro.html

After fresh installation on a new machine, my licensed copy of Adobe Encore CS6 "cannot run in non-royalty serialized mode."

"The application needs to be serialized with a royalty bearing serial number."
I have done everything recommended in all of the other threads relating to this issue -
Uninstalled the entire CS and used the Adobe cleaner tool - to no avail.
Uninstalled just Encore and re-installed, nothing.
And multiple combinations of the above mentioned.
Really need this to work, ASAP. We've tried to contact Adobe via phone, chat, and other means. They are very to receive an audience from, it appears. Can anyone offer a different solution?
This is for a brand new edit suite that is running Windows 7 pro, 32 GB of RAM, and the [email protected] GHz.

I did not see this earlier. Forums are a bit odd today.
Do you have a subscription (to the cloud) or is this a perpetual license? You cannot run Encore in trial mode.
Generally, with CS6 suite (or earlier?) this indicated that Premiere is not activated, or there is a problem with activation. What version are you trying to install?
Unfortunately, the link that tells you how to fix this went missing in action some time ago.

Can't Enable Web Services on a M276nw printer

Hi,
I am having trouble enabling HP Web Services on M276nw printer. Whenever I hit the "Enable" button it either says "Can't connect" or the loading page stays on for so long (have waited for more than 15mins) that I have to cancel the process manually. The printer is connected to the internet via wireless connection and to a computer, from which it was set up - again wirelessly.
I have looked at the forums here and tried powering off the printer and then the wireless router and them powering everyting on again, tried connecting to different wireless networks, but still can't enable Weservices.
I tried manually setting up a IPv4 connection, but unfortunately when I access the printer throughits IP adress in a browser, I can't see this specific part of the screen (as referred to by several people on the forums) where I can input DNS server details. Obviously my IPv4 Configuration Menu does not have these options.
Does anyone have ideas how I can solve this problem?
Any help is appreciated!
Regards,
Xepo

Hi Shlomi,
Many thanks for getting back to me. I tried your solution, but unfortunately doesn't work for me again.
I set up the DNS like you advised and as shown in the attached screenshot. After trying to enable webservices, it gives it a couple of tries and then show connection error.
Do you have any other suggestions? Anything is appreciated
Regards,
Xepo

Have an airplay enabled AV Receiver - how do i set up Airplay I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the

have an airplay enabled AV Receiver - how do i set up Airplay
I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the iphone App and via the web browser option.
Do I need Apple TV or to change some settings somewhere?
Any help would be greatly appreciated

You are making some progress with setup of wireless network. Apparently there is reliability problem with the wireless connection. Perhaps you want to refer to following Apple support documents and start tweaking parameters in the router to improve the reliability. I used to have third-party routers such as Belkin and Netgear but switched to Apple Airport routers (Time Capsule then Airport Extreme for now) because of incompatibility issues whenever Apple upgrade Mac OS X. But since Apple develops Airplay protocol as alternative to Bluetooth for wireless audio/video streaming (with much better bandwidth) and must be deployed in any wireless network, there is no reason third-party routers not working for Airplay protocol.
About AirPlay Mirroring in OS X Mountain Lion:
http://support.apple.com/kb/HT5404
iOS: Recommended settings for Wi-Fi routers and access points:
http://support.apple.com/kb/HT4199
Troubleshooting AirPlay and AirPlay Mirroring:
http://support.apple.com/kb/TS4215
Good luck in setting up 802.11 wirelesss network.

Can I enable simple finder for network accounts?

Can I enable simple finder for network accounts?

This was possible (drop dead easy) through MCX. It was one checkbox. If you are supporting older machines, you might still be able to push out MCX settings. My experience with 10.8.x is that MCX is inconsitent at best.
In Profile Manager... Best suggestion is to look at creating a custom profile. For what it is worth, this is the default MCX setting if the Simple Finder option was set on a user. Note the InterfaceLevel = Simple.
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
          <key>mcx_application_data</key>
          <dict>
                    <key>.GlobalPreferences</key>
                    <dict>
                              <key>Forced</key>
                              <array>
                                        <dict>
                                                  <key>mcx_preference_settings</key>
                                                  <dict>
                                                            <key>AppleShowAllExtensions</key>
                                                            <false/>
                                                  </dict>
                                        </dict>
                              </array>
                    </dict>
                    <key>com.apple.finder</key>
                    <dict>
                              <key>Forced</key>
                              <array>
                                        <dict>
                                                  <key>mcx_preference_settings</key>
                                                  <dict>
                                                            <key>AppleShowAllExtensions-immutable</key>
                                                            <true/>
                                                            <key>FinderSpawnWindow</key>
                                                            <false/>
                                                            <key>FinderSpawnWindow-immutable</key>
                                                            <true/>
                                                            <key>InterfaceLevel</key>
                                                            <string>Simple</string>
                                                            <key>NewWindowTargetIsHome</key>
                                                            <false/>
                                                            <key>NewWindowTargetIsHome-immutable</key>
                                                            <true/>
                                                            <key>OpenInColumnView</key>
                                                            <false/>
                                                            <key>OpenInColumnView-immutable</key>
                                                            <true/>
                                                            <key>ShowExternalHardDrivesOnDesktop</key>
                                                            <true/>
                                                            <key>ShowExternalHardDrivesOnDesktop-immutable</k ey>
                                                            <true/>
                                                            <key>ShowHardDrivesOnDesktop</key>
                                                            <true/>
                                                            <key>ShowHardDrivesOnDesktop-immutable</key>
                                                            <true/>
                                                            <key>ShowMountedServersOnDesktop</key>
                                                            <true/>
                                                            <key>ShowMountedServersOnDesktop-immutable</key>
                                                            <true/>
                                                            <key>ShowRemovableMediaOnDesktop</key>
                                                            <true/>
                                                            <key>ShowRemovableMediaOnDesktop-immutable</key>
                                                            <true/>
                                                            <key>WarnOnEmptyTrash</key>
                                                            <true/>
                                                            <key>WarnOnEmptyTrash-immutable</key>
                                                            <true/>
                                                  </dict>
                                        </dict>
                              </array>
                    </dict>
          </dict>
</dict>
</plist>

On render nodes I'm unable to download AE CC 13.1, all I get is 13.0

I updated AE on my workstations in the CC desktop app without a problem. The render nodes are not getting the update for AE in their CC desktop app. They definitely have AE CC 13.0 on them, and I can't figure out why the update doesn't just show in the app. I have tried making a deployment package of the newest AE, but nothing installed. I have tried uninstalling 13.0 and reinstalling using the desktop app. I have tried the tips here: CC desktop lists applications as "Up to Date" when not installed and Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6. I have tried accessing the direct download location here: https://creative.adobe.com/products/download/aftereffects but what I get is AE CC 2014 v13.0 which is not the newest. I'm stumped. Any ideas?
Thanks,
Miles
edit:
Workstations are win7 64-bit with lots of RAM and hard drive space
Render nodes are win7 64-bit with 12 GB RAM and about 20 GB free on the hard drive. They use onboard graphics.

That is a good guess, and luckily the problem wasn't the available hardware. I chatted with Adobe Support and they helped me locate the issue.
1. I had CC on the render nodes set to not auto update (which prevents updates from being available in CC)
2. The AE update needed Media Encoder to be current in order to install while auto updates were suppressed. ME was not updated enough for my AE update deployment to work(I think).
The fix was this:
1. Enable auto updates. Follow these instructions, but set Suppressed to 0 :Disable auto-updates | Application Manager | IT administrators
2. Relaunch the CC desktop Application. Your updates should appear in the Apps tab. Update all you want!
About Adobe Support:
I had a good experience chatting with Adobe Support. Singh read my initial message and was ready to start in with troubleshooting without me having to type information again. ;-)

Render node and Serial Numbers

I want to setup an Xserve as a render node with compressor. Do I need a whole new serial number for that or what is the deal?

Not if you just want to have it as part of a distributed processing network. You won't be able to send a project directly from FCP. You will have to fully render your sequences and make reference movies out of them, and then use that to send to Compressor. But the only thing you have to install for that is the Qmaster node. It is on the installation disk for FCS. You can put it on as many computers as you want, with no license, but you will always need a cluster controller, which is the machine that has Compressor (FC Studio) on it.

After Effect Network Render Error.

Hi Everyone,
I tryed the network render with use After Effect.
I use the Pipelinefx Qube 6.5 for to take a render.
After checking the logs I found out that its trying to run the following command:
cmdline : "C:\Program Files\Adobe\Adobe After Effects CS6\Support Files\aerender.exe" -project "\\nas-srv-1\vol_0_1\
Qube\TestProject\Test_Project.aep" -s
QB_FRAME_START -e QB_FRAME_END -i QB_FRAME_STEP -output "\\nas-srv-1\vol_0_1\Qube\out\BUG_LOOP_[#####].tga" -rqindex 1
So I try to execute this command on console manualy. I got license error. Then followed the procedure created necessary ae_render_only_node text files in document. I tryed the render command again and I have no longer the license error but a different error :
C:\Users\administrator.SYS>"C:\Program Files\Adobe\Adobe After Effects CS6\Support Files\aerender.exe" -project "\\nas-srv-1\vol_0_1\Qube\
TestProject\Test_Project.aep" -s QB_FRAME_START -e QB_FRAME_END -i QB_FRAME_STEP -output "\\nas-srv-1\vol_0_1\Qube\out
\BUG_LOOP_[#####].tga" -rqindex 1
aerender version 11.0x378
has video RAM(MB): 0
LoadLibrary "n" failed!
LoadLibrary "n" failed!
rqindex 1num 1
aerender Error: After Effects error: Unable to set ∟timeSpanStart↔. NaN is not anumber.
How can we fix this problem?
Thank you.
Ozan.

Have you tried mapping your NAS to a drive letter? Also for network volumes you can use UNC notation (forward slashes). I suspect that this is more of a generic issue where Windows doesn't resolve the network path to proper folder locations. It might also help to avoid dashes and numbers in the path names. Could be misinterpreted as aprt of the command string...
Mylenium

How can I enable embedded pl/sql gateway to run on port 80

I have a new 11G install on OEL 4.0, database created. I would like to be
able to access the instance using the pl/sql gateway. Works fine with
port 8080, the default. How to I enable it to run on port 80?
I found this statement in the following docuementation:
http://download.oracle.com/docs/cd/B19306_01/appdev.102/b14259/xdb22pro.htm#ADXDB2500
Using HTTP(S) on Nonstandard Ports
By default, HTTP listens on a nonstandard, unprotected port: 8080. To use HTTP(S) on
the standard port, such as 80, your DBA must chown the TNS listener to setuid ROOT
rather than setuid ORACLE, and configure the port number in the Oracle XML DB
configuration file /xdbconfig.xml.I have root priviledges on the box.
I've tried setting the listener file permissions:
chown root:dba /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
chmod 6775 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
Also put root in the dba group.
The permissions turn out like this:
-rwsr-sr-x 1 root dba 830854 Jun 17 21:04 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
I stopped the listener, bounced the database, and started the listener again.
But it still shows the process being owned by oracle:
oracle 29682 1 0 21:08 ? 00:00:00 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr LISTENER -inherit
Changing the port is easy:
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
8080 2100
At this point, I can access the apex home page with the following url:
http://hostname:8080/apex/f?p=4550:10:1454849288245548
I can than change it to port 80:
SYS>begin
dbms_xdb.sethttpport('80');
dbms_xdb.setftpport('2100');
end;
2 3 4 5
PL/SQL procedure successfully completed.
SYS>SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
80 2100
When I try to access apex with the following url:
http://rmdcopslnx1.us.oracle.com/apex/f?p=4550:10:1454849288245548
I get the following:
Failed to Connect
Firefox can't establish a connection to the server at hostname.com.
Though the site seems valid, the browser was unable to establish a connection.
* Could the site be temporarily unavailable? Try again later.
* Are you unable to browse other sites? Check the computer's network connection.
* Is your computer or network protected by a firewall or proxy? Incorrect settings
* can interfere with Web browsing.I can set the port. Just can't talk to it.
This is the entry from the listener log:
<msg time='2008-07-03T15:40:09.741-06:00' org_id='oracle' comp_id='tnslsnr'
type='UNKNOWN' level='16' host_id='hostname'
host_addr='xxx.xxx.xxx.xxx'>
<txt>TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
Linux Error: 13: Permission denied
</txt>
</msg>
So this looks like an permissions problem. But where? I posted
this on the apex forum here:
Re: How can I enable embedded pl/sql gateway to run on port 80
They suggested asking here.

No, that thread did not provide the information that I need. Some more data:
I have the port set to 8080:
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
8080 2100
At this point, I can access the apex home page with the following url:
http://hostname:8080/apex/f?p=4550:10:1454849288245548
I can than change it to port 80:
SYS>begin
dbms_xdb.sethttpport('80');
dbms_xdb.setftpport('2100');
end;
2 3 4 5
PL/SQL procedure successfully completed.
SYS>SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
80 2100
When I try to access apex with the following url:
http://rmdcopslnx1.us.oracle.com/apex/f?p=4550:10:1454849288245548
I get the following:
Failed to Connect
Firefox can't establish a connection to the server at hostname.com.
Though the site seems valid, the browser was unable to establish a connection.
* Could the site be temporarily unavailable? Try again later.
* Are you unable to browse other sites? Check the computer's network connection.
* Is your computer or network protected by a firewall or proxy? Incorrect settings can interfere with Web browsing.
I can set the port. Just can't talk to it.

Can't enable ACLs on a RAID volume

Hi all,
I have OSX 10.4.11 running on an Xserve G5 ppc. There are 2 Xserve RAID volumes attached by fibre channel.
I've been having issues recently with permissions: some users are creating or modifying files/folders and other users in the same group are then unable to access them. Viewing the permissions shows that group access is set to 'None'. I can correct this in the 'Sharing' section of WGM but that doesn't resolve the underlying issue.
I want to use ACLs to control access to data on the 2 RAID volumes, one of which also contains the users' network accounts. Unfortunately the 'Enable Access Control Lists' tick box is greyed out so I cannot activate them. On the other RAID volume all three tick boxes are available.
Why might this be?
John.

Found the answer. The volume was not correctly formatted. I copied the data, reformatted the volume, copied back the data and enabled ACLs.

New Mac OS Server on network, Windows box can't see other Macs anymore

I just put a Mac mini server on my network and the only services I have enabled are SMB, AFP and Open Directory. Before I put the server on the network (and if I turn the server off) the Windows 7 Pro machine I have on the network used to be able to see the rest of the Macs on the network in the Network section... I could see them, log on to one, grab files, etc. This also went for the Macs seeing the PC on the network in the Finder. Now that I have the server on the network though, I can't see the PC on my Macs and can't see my Macs on the PC. I can, however, do a "Map network drive" on the PC and enter an address to one of the Macs and connect that way. Anyone know why this could be happening?
Like I said, if I turn the server off or disconnect it from the network, the Macs will see the PC and the PC will see the Macs, but once its back on the network, they stop seeing each other, so its definitely something the server is doing that's causing it.
TIA

Confirm you have unique addresses and unique host names for the IP host names on your network. In absolute specifics, make absolutely certain your Mac OS X Server box is not configured at a conflicting address, or with a host name that conflicts with the Windows 7 box or with some other central and critical network resource such as your firewall or an IP router.
It's also possible you've got (for instance) a bad cable or a bad NIC and that's jamming up your network, though that's less likely.
Your Mac OS X Server box requires DNS be configured locally, or within your network.
Confirm unique host names. Confirm unique IP addresses. You can launch Terminal.app and use the dig command at the bash shell (+dig -x 192.168.1.1+ with whatever the local address, and +ping 192.168.1.1+ again with the local address and not with the 192.168.1.1 value shown, and +dig hostname.example.com+ or such for your domain name) or (if you're not comfortable in bash -- do go learn bash, regardless) then you can use the Network Utility in the Applications > Utilities folder.
It's also possible there's a problem with the managed switch configuration or such, but that probably isn't in use here.

Node can not join cluster after RAC HA Testing

Dear forum,
We are performing RAC failover tests according to document "RAC System Test Plan Outline 11gR2, Version 2.0". In testcase #14 - Interconnect network failure (11.2.0.2 an higher), we have disabled private interconnect network of node node1 (OCR Master).
Then - as expected - node node2 was evicted. Now, after enabling private interconnect network on node node1, i want to start CRS again on node2. However, node does not join cluster with messages:
2012-03-15 14:12:35.138: [ CSSD][1113114944]clssgmWaitOnEventValue: after CmInfo State val 3, eval 1 waited 0
2012-03-15 14:12:35.371: [ CSSD][1109961024]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301201, LATS 5535614, lastSeqNo 2301198, uniqueness 1331804892, timestamp 1331817153/13040714
2012-03-15 14:12:35.479: [ CSSD][1100884288]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301202, LATS 5535724, lastSeqNo 2301199, uniqueness 1331804892, timestamp 1331817154/13041024
2012-03-15 14:12:35.675: [ CSSD][1080801600]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301203, LATS 5535924, lastSeqNo 2301200, uniqueness 1331804892, timestamp 1331817154/13041364
Rebooting node2 did not help. Node1 which was online all the time (although private interconnect interface was unplugged for a few minutes and then plugged back in). I suppose that if we reboot node2, the problem will disappear. But there should be solution, which keeps availability requirements.
Setup:
2 Nodes (OEL5U7, UEK)
2 Storages
Network bonding via Linux bonding
GI 11.2.0.3.1
RDBMS 11.1.0.7.10
Any ideas?
Regards,
Martin

I have found a solution myself:
[root@node1 trace]# echo -eth3 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo -eth1 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo +eth1 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo +eth3 > /sys/class/net/bond1/bonding/slaves
Now node2 is automatically joining the cluster.
Regards,
martin

Windows XP mode Can't enable integration features

I noticed there are so many threads on this and all the discussions confuse the hell out of me.
Here's how it happened for me: I install Virtual PC, then install Windows XP mode. The VM boots up fine, everything is smooth, I can access my C drive from the VM and run an XP program as if it's operating from my host Win7 machine.
But I have to change the network settings so my bandwidth monitor which doesn't work on Win7 will recognize my host machine's traffic and log it. That requires a restart of XP mode. I do that and that's how this error happens. Now I can't enable integration
features no matter what I do.
I've followed steps in other threads. I deleted the .vsv file, set it to auto shut down or turn off instead of hibernate. The "Enable Integration features" button is greyed out. That cryptography FIPS thing or whatever it is is ALREADY disabled,
always has been. That didn't work for me.
Can anybody help me fix this?

Well, with all the minutia in your post it was difficult to decipher exactly what your were after.
If you have a question you should provide the specifics for the question and leave out all the irrelevant minutia. Details specific to the situation you want to resolve are what's important.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”
Hi I get "Can't enable Integration Features" error when starting XP mode, please help.
That better?
Either way, I fixed the problem by reinstalling XP Mode.

Can not enable fonts for User library in Font Book

Hi all,
For some reason I can not enable the user library in the font book using the options in the font book. This means that the User Library is "off". I have tried the following but none of them have worked:
* Reboot.
* Delete the Font preferance file.
* Undo the font book via booting in safe mode and then rebooting in normal mode. Delete the trash which contains the font cache.
* Manually insert fonts into User>Library>Fonts and restart.
* Manually empty user fonts folder and re-insert fonts back in.
* Delete the user fonts folder and re-create it and insert all fonts back in
Have also tried a few combinations of the above but none of them have worked. I do not want to use the system library fonts folder as this machine is on a network and the users should not have admin rights to their machines.
I have also checked the user rights to the user fonts folder and all seems ok there.
Does anyone know how to solve this problem so that I can enable the User font library?
Any help would be much appreciated.
Thanks
Slack

I have found that for me, on both a PowerMac G5 and an Intel iMac, both running 10.4.8 with all updates, turning on FileVault reliably causes the problem. I.E., if FontBook is working fine on an account which does not have FileVault turned on and I turn on FileVault, then the User collection in FontBook is greyed out and Enable "User" doesn't work. If FileVault is on, none of the suggested work-arounds that I have read about in these discussions or in Apple's support articles help.
Sometimes, turning off FileVault is sufficient. Other times, I must turn off FileVault and follow the work-around in http://docs.info.apple.com/article.html?artnum=302551 . Sometimes, I must turn off FileVault, throw away the FontBook preferences and restart.

CS6 AFX Network Render Node - Can't enable non-royalty bearing mode.

Similar Messages

Maybe you are looking for