CSCso80701 - "show policy-map interface" in 2960, 2970, 3560, 3750 should give error - 3
Have similar issues with 12.2(50)SE4....
Service-policy command has taken but cann't see in running config. Eventually no output "show policy-map interface fa0/x".
Try this config:
policy-map QOS-SOFTPHONE-POLICY
class QOS_VOICE_CLASS
set dscp cs3
class QOS_SIGNALING_CLASS
set dscp cs2
class QOS_DATA_CLASS
set dscp cs1
class class-default
set dscp default
BR
Similar Messages
-
CBWFQ: Question about the output of "show policy-map interface" command
Hi everyone,
I have a question about the output of "show policy-map interface" command.
The following is the output of this command and lower side of the output shows
(total queued/total drops/no-buffer drops) 0/342/0
If the packets drop occur due to the situation of no enough buffer,
"no-buffer drops" counted up. But "no-buffer drops" has not been counted up.
The "no-buffer drops" is 0 (zero) but "total drops" are counted as 342.
I guess there are other factors except "no-buffer drops" to add "total drops".
But I can not find any information about "other factors".
So I would like to know the "other factors" added to "total drops".
reserch-3725#sh policy-map interface fastethernet0/1
FastEthernet0/1
Service-policy output: shaping
Class-map: kdpc (match-all)
146956873 packets, 115209221595 bytes
5 minute offered rate 156000 bps, drop rate 0 bps
Match: access-group name YOKOHAMA_to_CHINO
Traffic Shaping
Target/Average Byte Sustain Excess Interval Increment
Rate Limit bits/int bits/int (ms) (bytes)
9360000/9360000 58500 234000 234000 25 29250
Adapt Queue Packets Bytes Packets Bytes Shaping
Active Depth Delayed Delayed Active
- 0 146956724 3539850811 2960247 3851843541 no
Class-map: class-default (match-any)
552458414 packets, 249687580329 bytes
5 minute offered rate 242000 bps, drop rate 0 bps
Match: any
Traffic Shaping
Target/Average Byte Sustain Excess Interval Increment
Rate Limit bits/int bits/int (ms) (bytes)
3072000/3072000 19200 76800 76800 25 9600
Adapt Queue Packets Bytes Packets Bytes Shaping
Active Depth Delayed Delayed Active
- 0 552453209 573909865 30358216 2926188156 no
Service-policy : policy1
Class-map: dlsw (match-all)
979578 packets, 264843255 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name acl-dlsw
Queueing
Output Queue: Conversation 137
Bandwidth 128 (kbps) Max Threshold 64 (packets)
(pkts matched/bytes matched) 20922/17371500
(depth/total drops/no-buffer drops) 0/0/0
Class-map: telnet (match-all)
29938 packets, 1806058 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name acl-telnet
Queueing
Output Queue: Conversation 138
Bandwidth 64 (kbps) Max Threshold 64 (packets)
(pkts matched/bytes matched) 639/38900
(depth/total drops/no-buffer drops) 0/0/0
Class-map: class-default (match-any)
551448911 packets, 249420939729 bytes
5 minute offered rate 242000 bps, drop rate 0 bps
Match: any
Queueing
Flow Based Fair Queueing
Maximum Number of Hashed Queues 128
(total queued/total drops/no-buffer drops) 0/342/0
Your information would be appreciated.Details infomatiuon regarding show policy-map interface
http://www.cisco.com/en/US/tech/tk543/tk545/technologies_tech_note09186a008010dd6a.shtml
http://www.cisco.com/en/US/tech/tk543/tk760/technologies_tech_note09186a0080108e2d.shtml
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/qos_r/qos_s2g.htm#wp1146884 -
Show policy-map interface | Question about QOS show command output
I hope this is the correct place for this question. If not, please let me know.
When I issue the show policy-map interface command (in this case on a 3845) there is some output I don't understand. I have included some output below and formatted the lines I am confused about as "computer code" which show up as red on my screen. A list of the individual lines i'm confused about is below, followed by those liens in the context of the show policy-map command's output.
Any help with this will be greatly appreciated. Thanks in advance.
5 minute offered rate 46000 bps, drop rate 0 bps
5 minute rate 10000 bps
bandwidth remaining 50% (768 kbps)
show policy-map interface
--- previous output omitted ---
GigabitEthernet0/0
Service-policy input: QoS_IN
class-map: Silver (match-any)
164691299 packets, 23570752398 bytes
5 minute offered rate 46000 bps, drop rate 0 bps
Match: access-group name MAINFRAME
4371992 packets, 2311242335 bytes
5 minute rate 0 bps
Match: access-group name KRONOS
13334297 packets, 3051409140 bytes
5 minute rate 5000 bps
Match: access-group name EMAIL
97652823 packets, 10323856470 bytes
5 minute rate 10000 bps
Match: access-group name VOIP-CONTROL
20782858 packets, 1481676784 bytes
5 minute rate 0 bps
Match: access-group name LOGIXWEB
0 packets, 0 bytes
5 minute rate 0 bps
Match: access-group name GRINDLOG
0 packets, 0 bytes
5 minute rate 0 bps
Match: access-group name CITRIX
46895 packets, 14669179 bytes
5 minute rate 0 bps
Match: access-group name CORP_WEB
28502414 packets, 6387897396 bytes
5 minute rate 4000 bps
QoS Set
dscp af31
Packets marked 164691269
show policy-map interface s0/0/0:0
Serial0/0/0:0
Service-policy output: QoS_OUT
--- previous output omitted ---
Class-map: Silver (match-any)
86590227 packets, 12051546524 bytes
5 minute offered rate 3000 bps, drop rate 0 bps
Match: access-group name MAINFRAME
7641084 packets, 2701232492 bytes
5 minute rate 0 bps
Match: access-group name KRONOS
6975052 packets, 1555404656 bytes
5 minute rate 0 bps
Match: access-group name EMAIL
58438150 packets, 5433636586 bytes
5 minute rate 3000 bps
Match: access-group name VOIP-CONTROL
355083 packets, 41252455 bytes
5 minute rate 0 bps
Match: access-group name LOGIXWEB
0 packets, 0 bytes
5 minute rate 0 bps
Match: access-group name GRINDLOG
0 packets, 0 bytes
5 minute rate 0 bps
Match: access-group name CITRIX
19 packets, 4967 bytes
5 minute rate 0 bps
Match: access-group name CORP_WEB
13180836 packets, 2320015236 bytes
5 minute rate 0 bps
Queueing
queue limit 64 packets
(queue depth/total drops/no-buffer drops) 0/18156/0
(pkts output/bytes output) 86421413/12004278837
bandwidth remaining 50% (768 kbps)this is my configuration
DGMGRL> show configuration
Configuration
Name: matrix
Enabled: YES
Protection Mode: MaxPerformance
Databases:
stdby1 - Primary database
stdby2 - Physical standby database
stdby3 - Physical standby database
Fast-Start Failover: DISABLED
Current status for "matrix":
SUCCESS
--- this is my first successful switchover -----
DGMGRL> switchover to stdby2
Performing switchover NOW, please wait...
New primary database "stdby2" is opening...
Operation requires shutdown of instance "stdby1" on database "stdby1"
Shutting down instance "stdby1"...
ORA-01109: database not open
Database dismounted.
ORACLE instance shut down.
Operation requires startup of instance "stdby1" on database "stdby1"
Starting instance "stdby1"...
ORACLE instance started.
Database mounted.
Switchover succeeded, new primary is "stdby2"
-------------------this is my second switchover -------------
DGMGRL> switchover to stdby1
Performing switchover NOW, please wait...
New primary database "stdby1" is opening...
Operation requires shutdown of instance "stdby2" on database "stdby2"
Shutting down instance "stdby2"...
ORA-01109: database not open
Database dismounted.
ORACLE instance shut down.
Operation requires startup of instance "stdby2" on database "stdby2"
Starting instance "stdby2"...
Unable to connect to database
ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
Failed.
You are no longer connected to ORACLE
Please connect again.
Unable to start instance "stdby2"
You must start instance "stdby2" manually
Switchover succeeded, new primary is "stdby1"
DGMGRL>
Edited by: user6981287 on Jan 7, 2010 12:57 AM
Edited by: user6981287 on Jan 7, 2010 1:00 AM -
DMVPN per tunnel QOS. show policy-map multipoint not working
Hi All,
I have a DMVPN hub which is a 1841 with image c1841-advsecurityk9-mz.151-4.M1.bin .
I have been using DMVPN and its awesome but now trying to get the QOS sorted out and having issues.
I have configured the interface like so.
interface Tunnel1
ip address 10.255.255.1 255.255.255.0
no ip redirects
ip mtu 1400
ip nhrp authentication xxx
ip nhrp map multicast dynamic
ip nhrp map group ADSL1 service-policy output ADSL1
ip nhrp network-id 1
ip nhrp redirect
ip tcp adjust-mss 1360
no ip split-horizon
ip ospf 1 area 0
tunnel source Loopback0
tunnel mode gre multipoint
tunnel key 1
tunnel path-mtu-discovery
tunnel protection ipsec profile VPN
end
policy-map ADSL1
class class-default
shape average 1000000
service-policy Classes
policy-map Classes
class Silver
bandwidth percent 25
fair-queue
class Gold
bandwidth percent 50
fair-queue
class Scavanger
bandwidth percent 5
class class-default
fair-queue
The output of show dmvpn detail shows it has applied the QOS rule.
NG-SR-WE-RT-2#show dmvpn detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding, W --> Waiting
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel1 is up/up, Addr. is 10.255.255.1, VRF ""
Tunnel Src./Dest. addr: 10.32.0.100/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "VPN"
Interface State Control: Disabled
Type:Hub, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 x.x.x.x 10.255.255.2 UP 1d18h D 10.255.255.2/32
NHRP group: ADSL1
Output QoS service-policy applied: ADSL1
but my router cannot run show policy-map multipoint... it doesnt come up with a tab but i can write it in by hand. Even when i write it in by hand it outputs blank.
I cut the ADSL1 shape down to 512k and it didnt take affect so i dont think the qos is working at all.
Is my feature set too low?
Cheers,
SimonRay,
There could be multiple reasons for it not to function, the config on hub seems just fine, we'd need to inspect the spokes and check (most likely) in debugs if correct group is being sent from spoke.
Also coexistance of other service-policy etc etc.
The feature is quite simple (some level of simplification), spoke says he is in group X when registering, hub assigns this NHRP mapping a service-policy.
M. -
Hi experts,
below is the output of show policy-map.
PE3-AMS-EU# show policy-map int serial 3/0/10:0 o
Serial3/0/10:0
Service-policy output: rao-pe-out
Class-map: pe-management-output (match-any)
0 packets, 0 bytes
30 second offered rate 0 bps, drop rate 0 bps
Match: access-group 107
0 packets, 0 bytes
30 second rate 0 bps
Queueing
queue limit 144 packets
(queue depth/total drops/no-buffer drops) 0/0/0
(pkts output/bytes output) 0/0
bandwidth 8 kbps
Exp-weight-constant: 7 (1/128)
Mean queue depth: 0 packets
class Transmitted Random drop Tail drop Minimum Maximum Mark
pkts/bytes pkts/bytes pkts/bytes thresh thresh prob
default 0/0 0/0 0/0 65535 65535 1/10
6 0/0 0/0 0/0 45 72 1/10
Class-map: pe-class1-output (match-any)
131960 packets, 8445440 bytes
30 second offered rate 249000 bps, drop rate 33000 bps
Match: ip precedence 4
131960 packets, 8445440 bytes
30 second rate 249000 bps
Police:
216000 bps, 2000 limit, 2000 extended limit
conformed 113909 packets, 7290176 bytes; action: transmit
exceeded 0 packets, 0 bytes; action: drop
violated 17856 packets, 1142784 bytes; action: drop
Class-map: pe-class2-output (match-any)
158740 packets, 64127887 bytes
30 second offered rate 1897000 bps, drop rate 157000 bps
Match: ip precedence 6
158740 packets, 64127887 bytes
30 second rate 1897000 bps
Match: ip precedence 2
0 packets, 0 bytes
30 second rate 0 bps
Queueing
queue limit 144 packets
(queue depth/total drops/no-buffer drops) 70/13397/0
(pkts output/bytes output) 149343/60928439
bandwidth 1586 kbps
Exp-weight-constant: 7 (1/128)
Mean queue depth: 69 packets
class Transmitted Random drop Tail drop Minimum Maximum Mark
pkts/bytes pkts/bytes pkts/bytes thresh thresh prob
default 10/575 0/0 0/0 65535 65535 1/10
6 149333/60927864 13191/5381928 206/84048 45 72 1/10
2 0/0 0/0 0/0 14 36 1/5
Class-map: class-default (match-any)
1352 packets, 546208 bytes
30 second offered rate 16000 bps, drop rate 45000 bps
Match: any
1352 packets, 546208 bytes
30 second rate 16000 bps
Queueing
queue limit 144 packets
(queue depth/total drops/no-buffer drops) 140/16394/0
(pkts output/bytes output) 101943/6932124
bandwidth 176 kbps
Exp-weight-constant: 7 (1/128)
Mean queue depth: 185 packets
class Transmitted Random drop Tail drop Minimum Maximum Mark
pkts/bytes pkts/bytes pkts/bytes thresh thresh prob
default 101943/6932124 0/0 15008/1020544 65535 65535 1/10
5 0/0 0/0 1386/565488 14 36 1/5
6 0/0 0/0 0/0 45 72 1/10
0 0/0 0/0 0/0 14 36 1/5
The min and max thresold value in the output are 65535 for default class.what is the significance of these values and what are those meant for.Why the values are 65535 ..Explanation for the threshold value 65535:
For example if you consider Class-map: class-default (match-any), WRED is configured only for IP Precedence 5, 6and 0, then rest of the IP Precedence values will come under the default, with no WRED configured. So under the default, tail drop is used for dropping the packets, instead of WRED.If there is no user-configured default profile, the default action is to tail drop. The value of 65535 displayed for max and min thresholds when there is no default configured is expected behavior; it just means we are going to tail drop.
I got the above solution from Developer.
Thanks,
satish -
Policy maps on port-channel sub-interfaces
We're trying to implement an enterprise QoS policy and I'm wondering how we can apply our QoS policy maps to several different sub-interfaces on a port-channel. In our case, we have both LAN and WAN connections that connect as VLANs on a switch and terminate as sub-interfaces on a port-channel that combines two Gigabit Ethernet interfaces on our router. The LAN connection will need to have a ingress service-policy to classify traffic as it comes from a customer LAN, and the WAN connections will have to have an egress service-policy to place the traffic classes into LLQ and CBWFQ queues as it leaves the router. Could I put both the ingress and egress service-policies on the physical router interface, or should I put them on the port-channel interface? Or should I apply them to the individual sub-interfaces? For example, I could put the ingress classification service-policy on the LAN sub-interface connection.
Any thoughts or insight would be helpful. Thanks.I can't put it as input because :
gw-a(config-subif)#service-policy input policy_upload
Traffic Shaping feature not supported in input policy.
Here's a show during a bandwidth test. You can see the offered rate is properly measured and is _way_ above the target shape rate.
gw-a#show policy-map interface Port-channel 1.2
Port-channel1.2
Service-policy output: policy_upload
Class-map: class-default (match-any)
624006 packets, 842239036 bytes
5 minute offered rate 12774000 bps, drop rate 0 bps
Match: any
Queueing
queue limit 64 packets
(queue depth/total drops/no-buffer drops) 0/0/0
(pkts output/bytes output) 0/0
shape (average) cir 100000, bc 400, be 400
target shape rate 100000 -
Policy-map input on an interface VLAN
Hi there,
I have a problem with a policy-map on an interface VLAN on my Cisco 6509-E.
The switch has the IOS Version 12.2(33)SXI10, RELEASE SOFTWARE (fc2).
I have configured this policy-map:
policy-map PM-10Mbit
class class-default
police cir 10000000 bc 1875000 be 3750000 conform-action transmit exceed-action drop violate-action drop
I bind this map on a physical interface
interface GigabitEthernet2/2
description <removed>
ip vrf forwarding <removed>
ip address <removed>
ip access-group <removed> out
service-policy input PM-10Mbit
service-policy output PM-10Mbit
and get this result:
show policy-map interface
GigabitEthernet2/2
Service-policy input: PM-10Mbit
class-map: class-default (match-any)
Match: any
police :
10000000 bps 1875000 limit 1875000 extended limit
Earl in slot 5 :
6428065284 bytes
5 minute offered rate 14696 bps
aggregate-forwarded 6294160565 bytes action: transmit
exceeded 133904719 bytes action: drop
aggregate-forward 584 bps exceed 0 bps
Service-policy output: PM-10Mbit
class-map: class-default (match-any)
Match: any
police :
10000000 bps 1875000 limit 1875000 extended limit
Earl in slot 4 :
10335145381 bytes
5 minute offered rate 21536 bps
aggregate-forwarded 10142894661 bytes action: transmit
exceeded 192250720 bytes action: drop
aggregate-forward 128 bps exceed 0 bps
Earl in slot 5 :
263335780 bytes
5 minute offered rate 176 bps
aggregate-forwarded 263335780 bytes action: transmit
exceeded 0 bytes action: drop
aggregate-forward 448 bps exceed 0 bps
But when I bind it on an interface VLAN i see no incoming traffic:
show policy-map interface
Vlan1012
Service-policy input: PM-100Mbit
class-map: class-default (match-any)
Match: any
police :
100000000 bps 18750000 limit 18750000 extended limit
Earl in slot 4 :
0 bytes
30 second offered rate 0 bps
aggregate-forwarded 0 bytes action: transmit
exceeded 0 bytes action: drop
aggregate-forward 0 bps exceed 0 bps
Earl in slot 5 :
0 bytes
30 second offered rate 0 bps
aggregate-forwarded 0 bytes action: transmit
exceeded 0 bytes action: drop
aggregate-forward 0 bps exceed 0 bps
Service-policy output: PM-100Mbit
class-map: class-default (match-any)
Match: any
police :
100000000 bps 18750000 limit 18750000 extended limit
Earl in slot 4 :
1005376843668 bytes
30 second offered rate 33016448 bps
aggregate-forwarded 1005362388151 bytes action: transmit
exceeded 14455517 bytes action: drop
aggregate-forward 30943792 bps exceed 0 bps
Earl in slot 5 :
1828318775 bytes
30 second offered rate 1296 bps
aggregate-forwarded 1828318775 bytes action: transmit
exceeded 0 bytes action: drop
aggregate-forward 1272 bps exceed 0 bps
Is this a bug or am I doing something wrong here?Hello
As I understand it , this is command is required in mls qos because on a SVI ( L3 vlan interface) runs in a vlan-based mode which differs from normal L3 routed interfaces which run in interface mode.
As per cisco ="In VLAN-based mode, the policy map that is attached to the Layer 2 interface is ignored, and QoS is driven by the policy map that is attached to the corresponding VLAN interface."
Lastly regards
Try matching on all traffic incoming on the trunk interface on that switch for it to successfully police incoming traffic:
class-map V102
match input-interface x/x
Policy-map POLICE
class V102
Police xxxx xxxx
res
Paul -
Ok I am going insane here! I have a policy map on one of my 5k's but not the other and seem to create it either. They are in an active/active pair. Here is the policy, can someone help me understand what it is and maybe why I cant create it on my other device?
policy-map type control-plane copp-system-policy-customized
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytesYes vPC pair. The issue is I enter the commands but they do not show in the running config on one of the two units...
N5K1
N5K2
show policy-map type control-plane
policy-map type control-plane copp-system-policy-customized
class copp-system-class-igmp
police cir 1024 kbps bc 65535 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-default
class copp-system-class-igmp
police cir 1024 kbps bc 65535 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-scaled-l2
class copp-system-class-igmp
police cir 4096 kbps bc 264000 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-scaled-l3
class copp-system-class-igmp
police cir 4096 kbps bc 264000 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 4000 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 4000 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 4000 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 512 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
NEXUS5K001# show policy-map interface control-plane
Control Plane
service-policy input: copp-system-policy-customized
class-map copp-system-class-igmp (match-any)
match protocol igmp
police cir 1024 kbps , bc 65535 bytes
conformed 834102 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-pim-hello (match-any)
match protocol pim
police cir 1024 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-bridging (match-any)
match protocol bridging
police cir 20000 kbps , bc 4800000 bytes
conformed 184965072 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-arp (match-any)
match protocol arp
match protocol nd
police cir 1024 kbps , bc 3600000 bytes
conformed 1711299342 bytes; action: transmit
violated 467458 bytes;
class-map copp-system-class-dhcp (match-any)
match protocol dhcp
police cir 1024 kbps , bc 4800000 bytes
conformed 96669859 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mgmt (match-any)
match protocol mgmt
police cir 12000 kbps , bc 4800000 bytes
conformed 3420991988 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-lacp (match-any)
match protocol lacp
police cir 1024 kbps , bc 4800000 bytes
conformed 5003732 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-lldp (match-any)
match protocol lldp_dcx
police cir 2048 kbps , bc 4800000 bytes
conformed 8283269 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-udld (match-any)
match protocol udld
police cir 2048 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-isis (match-any)
match protocol isis_dce
police cir 1024 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-msdp (match-any)
match protocol msdp
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-cdp (match-any)
match protocol cdp
police cir 1024 kbps , bc 4800000 bytes
conformed 5995146 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-fip (match-any)
match protocol fip
police cir 1024 kbps , bc 4800000 bytes
conformed 7396000 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-bgp (match-any)
match protocol bgp
police cir 9600 kbps , bc 4800000 bytes
conformed 52049287 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-eigrp (match-any)
match protocol eigrp
match protocol eigrp6
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-exception (match-any)
match protocol exception
police cir 64 kbps , bc 4800000 bytes
conformed 16415315 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-glean (match-any)
match protocol glean
police cir 1024 kbps , bc 4800000 bytes
conformed 94203992002 bytes; action: transmit
violated 5920334550 bytes;
class-map copp-system-class-hsrp-vrrp (match-any)
match protocol hsrp_vrrp
match protocol hsrp6
police cir 1024 kbps , bc 256000 bytes
conformed 54227844 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-icmp-echo (match-any)
match protocol icmp_echo
police cir 64 kbps , bc 3600000 bytes
conformed 184940591 bytes; action: transmit
violated 46970 bytes;
class-map copp-system-class-ospf (match-any)
match protocol ospf
match protocol ospf3
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-pim-register (match-any)
match protocol reg
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-rip (match-any)
match protocol rip
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-l3dest-miss (match-any)
match protocol unicast
police cir 64 kbps , bc 16000 bytes
conformed 4214 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mcast-miss (match-any)
match protocol multicast
police cir 256 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-excp-ip-frag (match-any)
match protocol ip_frag
police cir 64 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-excp-same-if (match-any)
match protocol same-if
police cir 64 kbps , bc 3200000 bytes
conformed 17075590565 bytes; action: transmit
violated 370668351863 bytes;
class-map copp-system-class-excp-ttl (match-any)
match protocol ttl
police cir 64 kbps , bc 3200000 bytes
conformed 1243144216 bytes; action: transmit
violated 1611787 bytes;
class-map copp-system-class-default (match-any)
match protocol default
police cir 512 kbps , bc 6400000 bytes
conformed 157079876 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-rpf-fail (match-any)
police cir 512 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mcast-last-hop (match-any)
police cir 512 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
NEXUS5K001# show running copp all
!Command: show running-config copp all
!Time: Wed Mar 31 13:35:40 2010
version 6.0(2)N1(2a)
control-plane
scale-factor 1.00 module 1
scale-factor 1.00 module 2
scale-factor 1.00 module 3
control-plane
service-policy input copp-system-policy-customized
NEXUS5K001#
Nexus 5000 Switch
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
NEXUS5K002# show policy-map type control-plane
policy-map type control-plane copp-system-policy-customized
class copp-system-class-igmp
police cir 1024 kbps bc 65535 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-default
class copp-system-class-igmp
police cir 1024 kbps bc 65535 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-scaled-l2
class copp-system-class-igmp
police cir 4096 kbps bc 264000 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 1024 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 64 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 256 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
policy-map type control-plane copp-system-policy-scaled-l3
class copp-system-class-igmp
police cir 4096 kbps bc 264000 bytes
class copp-system-class-pim-hello
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bridging
police cir 20000 kbps bc 4800000 bytes
class copp-system-class-arp
police cir 4000 kbps bc 3600000 bytes
class copp-system-class-dhcp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-mgmt
police cir 12000 kbps bc 4800000 bytes
class copp-system-class-lacp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-lldp
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-udld
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-isis
police cir 2048 kbps bc 4800000 bytes
class copp-system-class-msdp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-cdp
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-fip
police cir 1024 kbps bc 4800000 bytes
class copp-system-class-bgp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-eigrp
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-exception
police cir 64 kbps bc 4800000 bytes
class copp-system-class-glean
police cir 4000 kbps bc 4800000 bytes
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-icmp-echo
police cir 4000 kbps bc 3600000 bytes
class copp-system-class-ospf
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-pim-register
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-rip
police cir 9600 kbps bc 4800000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
class copp-system-class-mcast-miss
police cir 512 kbps bc 3200000 bytes
class copp-system-class-excp-ip-frag
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-same-if
police cir 64 kbps bc 3200000 bytes
class copp-system-class-excp-ttl
police cir 64 kbps bc 3200000 bytes
class copp-system-class-default
police cir 512 kbps bc 6400000 bytes
class copp-system-class-rpf-fail
police cir 512 kbps bc 3200000 bytes
class copp-system-class-mcast-last-hop
police cir 512 kbps bc 3200000 bytes
NEXUS5K002# show policy-map interface control-plane
Control Plane
service-policy input: copp-system-policy-customized
class-map copp-system-class-igmp (match-any)
match protocol igmp
police cir 1024 kbps , bc 65535 bytes
conformed 1099702577173 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-pim-hello (match-any)
match protocol pim
police cir 1024 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-bridging (match-any)
match protocol bridging
police cir 20000 kbps , bc 4800000 bytes
conformed 1117682720167 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-arp (match-any)
match protocol arp
match protocol nd
police cir 1024 kbps , bc 3600000 bytes
conformed 7392073468 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-dhcp (match-any)
match protocol dhcp
police cir 1024 kbps , bc 4800000 bytes
conformed 1554060880 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mgmt (match-any)
match protocol mgmt
police cir 12000 kbps , bc 4800000 bytes
conformed 3360293230 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-lacp (match-any)
match protocol lacp
police cir 1024 kbps , bc 4800000 bytes
conformed 1100653025235 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-lldp (match-any)
match protocol lldp_dcx
police cir 2048 kbps , bc 4800000 bytes
conformed 1101335075091 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-udld (match-any)
match protocol udld
police cir 2048 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-isis (match-any)
match protocol isis_dce
police cir 1024 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-msdp (match-any)
match protocol msdp
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-cdp (match-any)
match protocol cdp
police cir 1024 kbps , bc 4800000 bytes
conformed 1100822976136 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-fip (match-any)
match protocol fip
police cir 1024 kbps , bc 4800000 bytes
conformed 1334982352 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-bgp (match-any)
match protocol bgp
police cir 9600 kbps , bc 4800000 bytes
conformed 55322608 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-eigrp (match-any)
match protocol eigrp
match protocol eigrp6
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-exception (match-any)
match protocol exception
police cir 64 kbps , bc 4800000 bytes
conformed 7678996 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-glean (match-any)
match protocol glean
police cir 1024 kbps , bc 4800000 bytes
conformed 22710843199 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-hsrp-vrrp (match-any)
match protocol hsrp_vrrp
match protocol hsrp6
police cir 1024 kbps , bc 256000 bytes
conformed 12316200612 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-icmp-echo (match-any)
match protocol icmp_echo
police cir 64 kbps , bc 3600000 bytes
conformed 50470007 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-ospf (match-any)
match protocol ospf
match protocol ospf3
police cir 9600 kbps , bc 4800000 bytes
conformed 3366 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-pim-register (match-any)
match protocol reg
police cir 9600 kbps , bc 4800000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-rip (match-any)
match protocol rip
police cir 9600 kbps , bc 4800000 bytes
conformed 12510 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-l3dest-miss (match-any)
match protocol unicast
police cir 64 kbps , bc 16000 bytes
conformed 15136 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mcast-miss (match-any)
match protocol multicast
police cir 256 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-excp-ip-frag (match-any)
match protocol ip_frag
police cir 64 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-excp-same-if (match-any)
match protocol same-if
police cir 64 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-excp-ttl (match-any)
match protocol ttl
police cir 64 kbps , bc 3200000 bytes
conformed 8531281 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-default (match-any)
match protocol default
police cir 512 kbps , bc 6400000 bytes
conformed 33212075608 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-rpf-fail (match-any)
police cir 512 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
class-map copp-system-class-mcast-last-hop (match-any)
police cir 512 kbps , bc 3200000 bytes
conformed 0 bytes; action: transmit
violated 0 bytes;
NEXUS5K002# show running copp all
!Command: show running-config copp all
!Time: Wed Mar 31 13:38:37 2010
version 6.0(2)N1(2a)
control-plane
scale-factor 1.00 module 1
scale-factor 1.00 module 2
scale-factor 1.00 module 3
policy-map type control-plane copp-system-policy-customized
class copp-system-class-hsrp-vrrp
police cir 1024 kbps bc 256000 bytes
class copp-system-class-l3dest-miss
police cir 64 kbps bc 16000 bytes
control-plane
service-policy input copp-system-policy-customized
NEXUS5K002# -
4506- 12.2.25SG Sup2+ 'sho policy-map int' output
-IOS command 'sho policy-map int fa 3/x' doesnot show value for only one interface rather it shows cumulative value for all interfaces. Could be a bug in IOS ?
IOS: cat4500-ipbasek9-mz.122-25.SG.bin
#sho policy-map int fa3/6
FastEthernet3/6
Service-policy input: untrusted_model
Class-map: voice_trafic (match-all)
16626976 packets
Match: access-group name voice_trafic
QoS Set
ip dscp ef
Class-map: voice_signaling (match-all)
75954 packets
Match: access-group name voice_signaling
QoS Set
ip dscp ef
Class-map: class-default (match-any)
174134940 packets
Match: any
QoS Set
ip dscp default
#sho policy-map int fa3/5
FastEthernet3/5
Service-policy input: untrusted_model
Class-map: voice_trafic (match-all)
16636254 packets
Match: access-group name voice_trafic
QoS Set
ip dscp ef
Class-map: voice_signaling (match-all)
75954 packets
Match: access-group name voice_signaling
QoS Set
ip dscp ef
Class-map: class-default (match-any)
174161775 packets
Match: any
QoS Set
ip dscp default
#sho policy-map int fa3/5
FastEthernet3/5
Service-policy input: untrusted_model
Class-map: voice_trafic (match-all)
16639246 packets
Match: access-group name voice_trafic
QoS Set
ip dscp ef
Class-map: voice_signaling (match-all)
75954 packets
Match: access-group name voice_signaling
QoS Set
ip dscp ef
Class-map: class-default (match-any)
174167019 packets
Match: any
QoS Set
ip dscp default
#sho policy-map int fa3/5
FastEthernet3/5
Service-policy input: untrusted_model
Class-map: voice_trafic (match-all)
16641517 packets
Match: access-group name voice_trafic
QoS Set
ip dscp ef
Class-map: voice_signaling (match-all)
75954 packets
Match: access-group name voice_signaling
QoS Set
ip dscp ef
Class-map: class-default (match-any)
174175910 packets
Match: any
QoS Set
ip dscp defaultThe show policy-map interface command displays the packet statistics for classes on the specified interface or the specified PVC only if a service policy has been attached to the interface or the PVC.
check out the following link for the command reference :
http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_command_reference_chapter09186a008017cf12.html#wp1146884 -
Catalyst 3550 & 3560/3750 command 'show mls qos interface statistics'
On the Catalyst 3550 the command 'show mls qos interface statistics' will show ingress packet (or byte) counts with DSCP values. If you have policers configured then it also shows a count of packets that have been marked down to another DSCP value due to policing or any that have been dropped (obviously 'mls qos monitor dscp x' needs configuring). The same command on the 3560/3750 only shows the ingress & egress DSCP values, there is no column that shows packets (or bytes) that have been policed or dropped. Is there any command to display the same information with the 3560/3750?
Neither platform show counters when the command 'show policy-map interface x/x' is used so this won't work.
Thanks
AndyHi, I believe there is a command on the 3560 'sh mls qos interface policers' may be what you are looking for.
Here is what the command says it outputs:
To display QoS information at the interface level. This information includes:
The configuration of the egress queues and the CoS3-to-egress-queue map
Which interfaces have configured policers
Ingress and egress statistics, which includes the number of bytes that have been dropped -
QoS on 3560, 2960 and 3750 does not work (Policy-map).
Hi
I am tryng to configure QoS on 3 switches (2960, 3560 and 3750) with this configuration:
mls qos
class-map match-all QOS_DATA_CLASS
match access-group name QOS-DATA
class-map match-all QOS_DEFAULT_CLASS
match access-group name QOS-DEFAULT
class-map match-all QOS_VOICE_CLASS
match access-group name QOS-VOICE
class-map match-all QOS_SIGNALING_CLASS
match access-group name QOS-SIGNALING
policy-map QOS-SOFTPHONE-POLICY
class QOS_DEFAULT_CLASS
set dscp default
class QOS_SIGNALING_CLASS
set dscp cs2
class QOS_DATA_CLASS
set dscp cs1
class QOS_VOICE_CLASS
set dscp cs3
interface GigabitEthernet0/34
no switchport
ip address 10.10.11.1 255.255.255.252
ip ospf network point-to-point
priority-queue out
service-policy input QOS-SOFTPHONE-POLICY
interface GigabitEthernet0/47
switchport access vlan 150
spanning-tree portfast
service-policy input QOS-SOFTPHONE-POLICY
ip access-list extended QOS-DATA
permit tcp any any eq 22
permit tcp any any eq 465
permit tcp any any eq 143
permit tcp any any eq 993
permit tcp any any eq 995
permit tcp any any eq 1914
permit tcp any any eq ftp
permit tcp any any eq ftp-data
permit tcp any any eq smtp
permit tcp any any eq pop3
ip access-list extended QOS-DEFAULT
permit ip any any
ip access-list extended QOS-SIGNALING
permit tcp any any range 2000 2002
permit tcp any any range 5060 5061
permit udp any any range 5060 5061
ip access-list extended QOS-VOICE
permit udp any any range 16384 32767
but when I check the show commands I see that QoS is not working.
CoreA#sh policy-map interface g0/34
GigabitEthernet0/34
Service-policy input: QOS-SOFTPHONE-POLICY
Class-map: QOS_DEFAULT_CLASS (match-all)
3 packets, 198 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DEFAULT
Class-map: QOS_SIGNALING_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-SIGNALING
Class-map: QOS_DATA_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DATA
Class-map: QOS_VOICE_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-VOICE
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
CoreA#sh policy-map interface g0/47
GigabitEthernet0/47
Service-policy input: QOS-SOFTPHONE-POLICY
Class-map: QOS_DEFAULT_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DEFAULT
Class-map: QOS_SIGNALING_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-SIGNALING
Class-map: QOS_DATA_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DATA
Class-map: QOS_VOICE_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-VOICE
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
What do I do bad?
The flow is the next:
Computer with CIPC --------> Switch 2960 or 3560 or 3750 ------------------> switch core ---------------> CIPC
I have wireshark in a port mirror on switch 2960, 3560 and 3750. In wireshark I always see the packets marked with default label.
I hope you can help me.
Regards.Try this config:
policy-map QOS-SOFTPHONE-POLICY
class QOS_VOICE_CLASS
set dscp cs3
class QOS_SIGNALING_CLASS
set dscp cs2
class QOS_DATA_CLASS
set dscp cs1
class class-default
set dscp default
BR -
Policy map not show results in Cat6500
I have configured QoS in Catalyst 6513 for telepresence service and when I do "show policy interface gix/y" don't show the traffic is being marked.
I think that the QoS is marked the traffic correctly because I am sawing packets marked with AF41 in the next hop for that suspect that the problem is in the "show comand".
It´s normal this behaviour or it could be a IOS bug?
This is the configuration:
ip access-list extended ACLtelepresencia_in
permit ip any any
class-map match-any telepresencia
match access-group name ACLtelepresencia_in
policy-map telepresencia_in
class telepresencia
set dscp af41
D08MNSSRS0#sh policy-map interface GigabitEthernet3/13
GigabitEthernet3/13
Service-policy input: telepresencia_in
Class-map: telepresencia (match-any)
0 packets, 0 bytes
30 second offered rate 0 bps, drop rate 0 bps
Match: access-group name ACLtelepresencia_in
0 packets, 0 bytes
30 second rate 0 bps
Class-map: class-default (match-any)
0 packets, 0 bytes
30 second offered rate 0 bps, drop rate 0 bps
Match: any
Regards
AlbertoTry the query as
select sum(t.total) from
SELECT T0.DocNum, T0.DocTotal,T0.DocTotal - T0.VatSum, T0.DocDate, Sum(T0.DocTotal) as Total,Sum(T0.DocTotal - T0.VatSum) as withoutTax FROM ORDR T0 INNER JOIN OSLP T1 ON T0.SlpCode = T1.SlpCode
WHERE T1.SlpName ='Rajesh Nair' and T1.SlpCode -1
GROUP BY T0.DocNum, T0.DocDate, T0.VatSum, T0.DocTotal
) t
or in one query at the end as sum as
SELECT T0.DocNum, T0.DocTotal,T0.DocTotal - T0.VatSum, T0.DocDate, Sum(T0.DocTotal) as Total,Sum(T0.DocTotal - T0.VatSum) as withoutTax FROM ORDR T0 INNER JOIN OSLP T1 ON T0.SlpCode = T1.SlpCode
WHERE T1.SlpName ='Rajesh Nair' and T1.SlpCode -1
GROUP BY T0.DocNum, T0.DocDate, T0.VatSum, T0.DocTotal
UNION
select null, null, null, null, sum(t.total), null from
SELECT T0.DocNum, T0.DocTotal,T0.DocTotal - T0.VatSum, T0.DocDate, Sum(T0.DocTotal) as Total,Sum(T0.DocTotal - T0.VatSum) as withoutTax FROM ORDR T0 INNER JOIN OSLP T1 ON T0.SlpCode = T1.SlpCode
WHERE T1.SlpName ='Rajesh Nair' and T1.SlpCode -1
GROUP BY T0.DocNum, T0.DocDate, T0.VatSum, T0.DocTotal
) t -
dear all,
how to configure policy-map on catalyst 3550 to shapping bandwidth. I've tried to setting that police-map in one of interface, but when I wrote sh policy-map interface fa0/1, in class-map field, the result are
class-map: policeIn (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
match: access-group 112qm_police_inform_feature: CLASS_SHOW
Could u give me a clue..??
thx.
..::rhiez::..hi,
i've checked statistic of interface and there is traffic on that interface :
Hardware is Fast Ethernet, address is xxxx.xxxx.xxxx.xxxx(bia xxxx.xxxx.xxxx)
MTU 1500 bytes, BW 512 Kbit, DLY 100 usec,
reliability 255/255, txload 102/255, rxload 42/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 00:03:16
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 85000 bits/sec, 67 packets/sec
5 minute output rate 961000 bits/sec, 201 packets/sec
12965 packets input, 2137646 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
38564 packets output, 23504798 bytes, 0 underruns
0 output errors, 46 collisions, 0 interface resets
0 babbles, 0 late collision, 62 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
is there another way to shapping bandwidth per vlan or per port interface on catalyst 3550 with IOS 12.1(8).
thx.
..::rhiez::.. -
ME3400E parent child policy map
I've pasted the output of the show policy-map that is applied to an interface that connected to an access layer switch - I want one customer to have 15MB and the other customers to share the remaining bandwidth of the 200MB of internet bandwidth we currently have.
Does it look like it is working? It has only been applied for an hour or 2 - I dont' understand why under the Class-map: cust1 is shows 0 packets, and under the service policy class-Map is shows 0 packets and 0 bytes, but it shows that packets are conforming under the police section . . .
ME.3400#sh policy-map int g0/11
GigabitEthernet0/11
Service-policy input: IP_Parent
Class-map: cust1 (match-any)
0 packets
Match: vlan 301
Service-policy : cust1
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police cir 15000000 bc 468750
conform-action transmit
exceed-action drop
conform: 3354685 (packets) 596174238 (bytes)
exceed: 0 (packets) 0 (bytes)
conform: 1945694 bps, exceed: 0 bps
Class-map: Shared_IP (match-any)
0 packets
Match: vlan 300
Service-policy : Shared_IP
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police cir 80000000 bc 1000000
conform-action transmit
exceed-action drop
conform: 878911 (packets) 145461269 (bytes)
exceed: 0 (packets) 0 (bytes)
conform: 409508 bps, exceed: 0 bps
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: anyHere is the output after letting it run for 6 days. Does anyone have an opinion about if it is working correctly?
I'm still confused by the places where it says 0 packets, or 0 packets, 0 bytes.
ME.3400#sh policy-map int g0/11
GigabitEthernet0/11
Service-policy input: IP_Parent
Class-map: cust1 (match-any)
0 packets
Match: vlan 301
Service-policy : cust1
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police cir 15000000 bc 468750
conform-action transmit
exceed-action drop
conform: 911003596 (packets) 153048040973 (bytes)
exceed: 445 (packets) 439435 (bytes)
conform: 2501473 bps, exceed: 0 bps
Class-map: Shared_IP (match-any)
0 packets
Match: vlan 300
Service-policy : Shared_IP
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police cir 180000000 bc 1000000
conform-action transmit
exceed-action drop
conform: 262737871 (packets) 42238049347 (bytes)
exceed: 0 (packets) 0 (bytes)
conform: 1005000 bps, exceed: 0 bps
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any -
Map-class frame-relay , policy map
Does a service-policy output have to be applied to an interface for qos to work?
here is the config but there is nothing applied to the serial interface..
Thanks for your help
policy-map 256/128KVoice
class 256/128KVoice
priority 112
class class-default
fair-queue
map-class frame-relay 256/128KVoice
frame-relay cir 128000
frame-relay bc 1280
frame-relay be 600
frame-relay mincir 128000
no frame-relay adaptive-shaping
frame-relay fair-queue
frame-relay fragment 150
frame-relay ip rtp priority 16384 16380 210
interface Serial0/0
bandwidth 1544
ip address xxx.xxx.xxx.xxx 255.255.255.255
ip route-cache flow
no fair-queue
service-module t1 timeslots 1-24Hello,
Will QOS will work in this way where class is put on WAN interface where it should be service policy.
router#sh run interface Se0/0/0.1
Building configuration...
Current configuration : 239 bytes
interface Serial0/0/0.1 point-to-point
bandwidth 2048
ip address XXXX
ip nat outside
frame-relay interface-dlci 555
class COS-OUT-S0/0/0.1
end
COS-OUT-S0/0/0.1 is defined as policy map with class of voice and video.
When checking on WAN int #sh policy-map interface Se0/0/0.1 , can see output of service policy input/output with policy map recpective classes and packets match entries.Is QOS working with this configuration?
Appreciate any input on this.
Regards,
Brajesh.
Maybe you are looking for
-
Dear All, I need to use bulk user creation through API. Please advice which API i use to resolve this issue. Thanks Rehan
-
Please help if someone can please, I purchased an iPod touch and a ipad2 from an apple store in the states last year, my daughter recently dropped the iPod touch and it now has a small crack across the screen, I was in the states just under a year ag
-
Multiple hide one 1 screen in an interactive report.
Dear All, I wish to do Hide tab1-fld1. hide tab1-fld2. Now when the user clicks on the fld1 my program will pick up data from one table and display it and when the user clicks on fld2 my program will pick up data from 2nd table and display it. How do
-
This is regarding info system setting Transaction code : OMO9 , Currently we are having the setting of Monthwise Report .. We want to convert the same to Daywise .. what are the implication ..?? what about earlier data which were updated as monthwise
-
Hi Gurus, I am trying to create Vendor by inbound IDOC by enhancing the standard FM IDOC_INPUT_CREDITOR but IDOC is getting posted with status 51: Status 51: Trans. XK01 record 3 : Data record is not flagged as record type 2