CSCue18444 - A packet is unable to reach HSRP VIP in other VRF

Hello,
i'm confused about which release of NXOS for the 7k has fixed this issue.
I have read the release notes for both release train 6.1 and 6.2 and the bug ID (CSCue18444) is not mentioned in there.
I know that the bug search mentiones the following releases are the bug fixed in:
5.2(9.115)S0
6.1(4.37)S0
6.2(1.59)S0
6.2(1.93)
7.0(0.7)
6.1(5.2)S0
Regards
Jocke W

We are experiencing a similiar type of condition on 7k NS/OS 6.1.(2). If a VLAN gets shut down on 7k1 (which is the peer), and HSRP for the VLAN becomes active on 7k2, everything is fine. When the VLAN is unshut on 7k1 which then preempts and becomes the active HSRP peer again for the VLAN, the HSRP gateway IP is no longer in the ARP table on 7k2. This has caused issues when servers are using the path through 7k2 but can't find the gateway IP to go to the 7k1 peer. If we ping the HSRP gateway IP from the 7k2 VRF it resides in, the IP and corresponding MAC are restored in the ARP table on 7k2, and both paths are again working as expected. Could this be similiar to this bug? (Also posted this on bug id CSCuh7946 that I found referenced in release notes for for 6.2). I'm also having issues finding resolution or specific references for this condition, and have also checked several other release notes. Another bug, CSCue54187 may also be similiar from - release notes for 5.2).
Thank you,
Lynn Morgan

Similar Messages

Mac Mini unable to reach NAS while MacBook Air can

Hi Everyone,
I've got an issue with my LAN. One computer on the LAN, a Mac Mini, is unable to reach the NAS even though all other devices can.
The setup is nothing exotic. It's a home wifi router from my local telco provider. On the Cabled interface I have a NAS, on the Wifi side I have several devices amongst which a Mac Mini and a Macbook Air. All IP addresses are handed out through DHCP. The DHCP server is set to assign a fixed address to both the NAS and the Mac Mini.
The Macbook and the Mac Mini can see each other just fine, the Macbook can access the NAS but the Mini can not. The Mini has no other issues to speak of, it can access everything else just fine.
The issue appears intermittent but I have not found a pattern. Rebooting the NAS, Mini or router individually had no effect. Below is a log of commands and output from the mac mini.
What should I be looking for to troubleshoot this appropriately?
[admin@htpc] ~ $ system_profiler SPSoftwareDataType
Software:
    System Software Overview:
      System Version: OS X 10.8.4 (12E55)
      Kernel Version: Darwin 12.4.0
      Boot Volume: Macintosh HD
      Boot Mode: Normal
      Computer Name: HTPC
      User Name: admin (admin)
      Secure Virtual Memory: Enabled
      Time since boot: 25 minutes
[admin@htpc] ~ $ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        options=3<RXCSUM,TXCSUM>
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4>
        ether 10:9a:dd:6d:8b:b7
        media: autoselect (none)
        status: inactive
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        ether 10:9a:dd:ba:d4:96
        inet6 fe80::129a:ddff:feba:d496%en1 prefixlen 64 scopeid 0x5
        inet 192.168.1.19 netmask 0xffffff00 broadcast 192.168.1.255
        media: autoselect
        status: active
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
        lladdr 70:cd:60:ff:fe:5a:f2:30
        media: autoselect <full-duplex>
        status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
        ether 02:9a:dd:ba:d4:96
        media: autoselect
        status: inactive
[admin@htpc] ~ $ arp -a
livebox.home (192.168.1.1) at 3c:81:d8:d7:bc:a4 on en1 ifscope [ethernet]
lightmac.home (192.168.1.15) at 10:93:e9:7:a8:66 on en1 ifscope [ethernet]
droboshare.home (192.168.1.20) at 0:1a:62:0:7:ce on en1 ifscope [ethernet]
? (192.168.1.255) at ff:ff:ff:ff:ff:ff on en1 ifscope [ethernet]
[admin@htpc] ~ $ ping droboshare.home
PING droboshare.home (192.168.1.20): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
Request timeout for icmp_seq 4
Request timeout for icmp_seq 5
Request timeout for icmp_seq 6
Request timeout for icmp_seq 7
Request timeout for icmp_seq 8
Request timeout for icmp_seq 9
^C
--- droboshare.home ping statistics ---
11 packets transmitted, 0 packets received, 100.0% packet loss

Hi Linc,
The NAS responds to pings from other devices on the network.
The Mac Mini has no other issues with regards to accessing the network or the Internet.
I'll restart the router once more to see if this has an effect, but so far no positive change.

SMTP 5.4.7 - Delivery expired - unable to reach nameserver on any valid IP

We recently started having issues delivering email to hotmail.com, aol.com, and amtrak.com addresses (possibly more domains, but
haven't heard of others yet). They return the following error (email addresses have been altered):
Diagnostic information for administrators:
Generating server: edmironport.internal.edmondok.com
[email protected]
#< #5.0.0 smtp; 5.4.7 - Delivery expired (message too old) 'DNS Soft Error looking up aol.com (MX) while asking recursive_nameserver1.parent. Error was: unable to reach nameserver on any valid IP' (delivery attempts: 0)> #SMTP#
Original message headers:
Received: from exch01.internal.edmondok.com ([192.168.xxx.xxx]) by
edmironport.edmondok.com with ESMTP; 29 Dec 2009 09:15:36 -0600
Received: from exch01.internal.edmondok.com ([192.168.xxx.xxx])
by edmironport.edmondok.com with ESMTP; 29 Dec 2009 09:15:40 -0600
Received: from EXCH01.internal.edmondok.com ([fe80::45fe:26d:54cd:6aeb]) by
EXCH01.internal.edmondok.com ([fe80::xxxx:xxxx:xxxx:xxxx%10]) with mapi; Tue, 29
Dec 2009 09:15:19 -0600
From: Internal User <[email protected]>
To: User <[email protected]>
Date: Tue, 29 Dec 2009 09:15:18 -0600
Subject: Blood Drive Today
Thread-Topic: Blood Drive Today
Thread-Index: AcqImccN9I6lWOw9QuGSrMji25lA2A==
Message-ID: [email protected]com
Accept-Language: en-US
Content-Language: en-US
X-MS-Has-Attach:
X-MS-TNEF-Correlator:
acceptlanguage: en-US
Content-Type: multipart/alternative;
boundary="_000_08B7F743EE3EF44F8B51C43EEB8902C4034FF1F5EXCH01interaled_"
MIME-Version: 1.0
X-Auto-Response-Suppress: DR, OOF, AutoReply
Any ideas as to why this is occuring? I have the ironport appliance's (C150) DNS pointing to our internal DNS servers. I am able to resolve all mailservers to IPs via nslookup and can ping hotmail.com's servers, but not aol.com's or amtrak.com's (possibly by their design?). There are some MX issues with AOL and Amtrak, but not Hotmail. Any help is appreciated. Thanks,
Hans Schroeder | Network Specialist
City of Edmond | www.edmondok.com
[email protected]

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hello Hans,
It looks like your DNS server(s) are overloaded or refusing their job for some other reason.
What is the response of your DNS servers when you request the problematic domains? Please try from Ironport nslookup and from any other nslookup/dig that is using the same DNS servers.
One thing that once bothered us was that our DNS servers where allowed to perform UDP queries only, some MX targets with a lot (in this case 18) of servers in their MX records exceeded the UDP packet size and DNS tried to switch over to TCP. that traffic was dropped so the DNS server never got it's result back. I think the MX records of AOL and Amtrak are not that bid (4 and 3 mail servers) but maybe it's a start.
You can also try to enable query logging on your DNS servers and check the results of that.
Good luck,
Steven

Unable to reach Adobe servers, Please check firewall settings and try again

I have been a creative cloud customer since it started and I've never experienced such buggy software as the app manager. The customer experience is just shocking and I wish Adobe would just offer direct downloads for the software we need rather than use the app manager.
I'm currently trying to install the latest versions of the programs but the app manager keeps showing "Unable to reach Adobe servers, Please check firewall settings and try again in a few minutes".
I do not have any firewalls on my network.
I've uninstalled all previous versions of the applications.
The app manager will download a few % and then the message appears again. I click retry and it downloads another few % before showing the message again. I keep doing this until the program is fully downloaded and installed which take hours. Because I am able to eventually download the app, the error should be anything to do with my setup or internet connection as I've never had this issue before when installing adobe products.
Is there a way we can bypass the app manager and install the programs directly? This is getting very annoying and I just need my apps to install without wasting days clicking the retry button.

I'm having the exact same problem. Photoshop is stuck at 0%.
Have the links for direct download changed? When I went to http://prodesigntools.com/adobe-cc-direct-download-links.htmland then scrolled down the page to:
Photoshop CC 2014 (64-bit)
740 MB
File 2
801 MB
File 1
and then clicked on File 1 and File 2, I reached a page that says "You don't have permission to access "http://trials3.adobe.com/AdobeProducts/PHSP/15/win64/Photoshop_15_LS20_win64.7z?" on this server."

Creative Cloud is telling me "Unable to reach Adobe servers. Please check your firewall settings, and try again in a few minutes.

Creative Cloud is telling me "Unable to reach Adobe servers. Please check your firewall settings, and try again in a few minutes.
What do I do to access the cloud? I have checked my firewall settings to allow for me to be able to use adobe cloud. Any Suggestions?

Try a different browser and/or turn your firewall off to download
or
A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

Runcluvfy.sh stage -pre crsinst: error Unable to reach any of the nodes

Hii all,
Well, I've gone through the pre-reqs for trying to install 11G clusterware on RHEL 5.3.
I'm to the point where i'm trying to run:
./runcluvfy.sh stage -pre crsinst -n node1 -verbose
I get this:
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check failed from node "node1 ".
Check failed on nodes:
node1
ERROR:
Unable to reach any of the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
I'm just wanting right now, to install a one node RAC system (I will add servers later as I get them online).
I've verified that ssh is working (thinking it may be trying to connect to itself by ssh). I have the keys generated and installed...if I connect ssh as the oracle user back to the same machine, it gets me right on with no prompts for passwords.
nslookup on node1 looks great.
This box has 2 cards....eth0 and eth1. Right now in the /etc/hosts file, I have node1 to the IP for eth0, and node1-priv set for the IP address eth1.
I do have a little trouble understanding what the node1-vip is supposed to do or be set. I found the an IP address one higher than for eth0 wasn't being used, and set node1-vip to be that.
(Can someone explain to me a little more about the vip host?? Is it supposed to somehow point to node1's IP address on eth0 like the regular one does?)
Since this is a one box, one node install...hoping clusterware and checks are just looking at the /etc/hosts file. I've tried playing around, and setting node1-vip to be the same as node1 (IP)...that doesn't work either.
One thing I can guess 'might' be wrong. Does runcluvfy use "ping"? I found the oracle user cannot ping this box from this box. The box (node1) can be pinged from outside the box...it is registered on DNS, I can ssh into it no problem, and again, oracle can ssh into himself on same box with keys properly generated).
I've been looking around, and I just don't see much of what to look at to troubleshoot with this error, I guess everyone gets past the verification the first time with no host unreachable errors?
I'm a bit weak when it comes to networking. Any help greatly appreciated...suggestions, links...etc!!
cayenne

Ok...looks like this was the problem. It appears the SA's, per newer policy, had turned off "ping" for any other user on the box besides root.
I took a shot in the dark, and had them turn it on (as that ssh'ing and other items to check seemed to work outside the runcluvfy script). They turned on ping. The nodes from the script are now reachable and test positive for equivalency.
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "node1"
Destination Node Reachable?
node1 yes
Result: Node reachability check passed from node "node1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node1 passed
Result: User equivalence check passed for user "oracle".
Pre-check for cluster services setup was unsuccessful on all the nodes.
I"m guessing that last line...was due to not having the clusterware running on any other boxes?
Anyway, will try to config. RAC, and get things installed.

I am unable to set up my iphone 5 after reset since am getting a error stating 'unable to reach server' . i tried restoring the same from my computer but i get a error stating server unavailable' . please help me as my phone is stuck at the set up page

i am unable to set up my iphone 5 after reset since am getting a error stating 'unable to reach server' . i tried restoring the same from my computer but i get a error stating server unavailable' . please help me as my phone is stuck at the set up page. so i have already tried recovery mode as well.

Contact Apple support for warranty service.

My adobe cloud desktop app seems to have stopped working. I keep getting a error message saying Unable to reach adobe servers, please check firewall settings.

My adobe cloud desktop app seems to have stopped working. I keep getting a error message saying Unable to reach adobe servers, please check firewall settings.
The creative cloud icon on the top menu bar is greyed out, and not updates show.
I have spoke to our internal IT and my settings are the same as my colleagues who's is working fine, can anybody help with this ongoing problem?

Grafix121 please ask your I.T. department to review the Adobe Creative Cloud Security FAQ for IT section of Creative Suite Enterprise Deployment | Adobe Developer Connection for information on how to configure your network to allow connections to the Adobe servers.

Unable to reach adobe servers, past 3 days Feb 20, 2015

for the past 3 days I've been getting a message when I trey to use the Adobe Application Manager after purchasing Adobe Creative Cloud service. I've tried two different computers, a Mac and a PC. Im also unable to get to the adobeid.services.adobe.com to reset my password (server not found), I have rebooted, shut down, shut down my firewall, check my hosts table for redirects. I can get to adobe.com because I'm posting here right now.
I contacted Adobe and chatted with an associate who was unhelpful, but I was told my request would be "Elevated to the relevant team", who have not made any attempt to contact me at this time.

Please refer to:
Unable to reach Adobe servers, Please check firewall settings and try again
In Creative Cloud Application "unable to reach adobe servers please check your firewall settings"
Unable to reach Adobe servers when opening Creative Cloud
They have host of information.
Regards
Rajshree

A fix for Mac users encountering "unable to reach Adobe servers" error

Seemingly out of nowhere - i.e., not coinciding with any Mac OS, or app updates - I started getting the "unable to reach Adobe servers" error from the Creative Cloud desktop app. Signing into the Adobe website was impossible, too. When I say impossible, I mean it literally - the login window would not display, in Safari or Chrome.
I'm sure this is posted somewhere here, but just in case, here's the solution that worked for me (posted by phatfish81 on Feb 7, 2015 4:35 PM):
https://discussions.apple.com/message/27683395?tstart=0

Luciac15720559 have you utilized the steps listed in Sign in, activation, or connection errors | CS5.5 and later to locate the cause of the connection error? If so do you have any questions regarding the steps listed within the document? What type of network environment is your computer located?

'Download Error' due to 'Unable to reach Adobe servers'.

I am getting a 'Download Error' due to 'Unable to reach Adobe servers'. I have already reconnected and disconnected my internet, and nothing has changed. How can I fix this problem? If anyone can help, I would truly be grateful. Thanks!
- Bobby Bobface

Not really a Premiere Pro problem, so moving this to the Downloading, Installing, Setting Up forum.
Re: Receiving error stating not able to access the Internet in Adobe Download Assistant

Adobe Download Manager unable to reach Adobe servers

I am getting the "Unable to reach Adobe servers" error all the time.
I've tried
deleting the opm.db file;
deleting the PDApp log file; and
entering my adobe login details.
turning off my avast firewall (there's none on my modem)
But the error doesn't go away and I can't upgrade to LR 5, etc.
Has anyone managed to fix this error?
Thanks,
Ganga.
PS:
a) I am not happy that I have to use the forums to get support on a product that I'm payingf for.
b) Why can't Adobe offer 24/7 support? I am in Australia and should not be made to wait for US business hours.
c) I wonder if Adobe will reimburse for the days they couldn't supply the product I've subscribed to.

Yes Jihoon1109 the managed network is likely causing your network difficulties. This is especially true once the steps listed in http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html have been completed.
I would recommend contacting your I.T. department and having them review the Adobe Creative Cloud Service Access Documentation for IT section of http://www.adobe.com/devnet/creativesuite/enterprisedeployment.html.

"Unable to Reach Servers" and "Connect to the Internet" Error Messages

Hi.
So, I purchased Adobe Audition at $19.99 per month for a year.
It hasn't worked yet.
I've tried all the online forum advice - drop firewall, check hosts file, check some certificate, remove/reinstall Audition ...nothing has worked. I still get messages saying "Unable to Reach Servers" and "Connect to the Internet." I'm ALWAYS connected to the Internet.
I use Windows 7 Home Premium SP1, 64-Bit operating system.
This needs to be fixed, or I want my money back.
Someone please help. I'm already 2 days with no access to something I've paid for. I don't like this.
-Karen

Karen did you have any questions regarding the steps listed in Sign in, activation, or connection errors | CC, CS6, CS5.5 - http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html. If your membership is valid then there must be a connection error between the computer and our activation server.
Are you on a managed network? Do you utilize a hardware firewall or proxy server?

Unable to reach Application Server. Contact your admin ( ERR WIJ 20010 )

Hi all,
When i am using web intelligence in infoview, i am getting the following error.
Unable to reach Application Server. Contact your administrator ( ERR WIJ 20010 ).
I have logged in using admin credentials.

Hi everyone.
Could I get a quick reply if this is still an issue for you all? If it is not, has anything changed in your environment. I have one person reporting this now.
Full log:
Version:12.1.8.1176
Application server:
............cdzisapi.wis
Stack trace:
java.net.ConnectException: Connection timed out: connect
at java.net.PlainSocketImpl.socketConnect(Native Method)
at java.net.PlainSocketImpl.doConnect(Unknown Source)
at java.net.PlainSocketImpl.connectToAddress(Unknown Source)
at java.net.PlainSocketImpl.connect(Unknown Source)
at java.net.SocksSocketImpl.connect(Unknown Source)
at java.net.Socket.connect(Unknown Source)
at sun.net.NetworkClient.doConnect(Unknown Source)
at sun.net.www.http.HttpClient.openServer(Unknown Source)
at sun.net.www.http.HttpClient.openServer(Unknown Source)
at sun.net.www.http.HttpClient.<init>(Unknown Source)
at sun.net.www.http.HttpClient.New(Unknown Source)
at sun.net.www.http.HttpClient.New(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getNewHttpClient(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.plainConnect(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.connect(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getOutputStream(Unknown Source)
at com.businessobjects.wp.cpi.CPIConnection.postRequest(Unknown Source)
at com.businessobjects.wp.xml.XMLViaHttp.loadScript(Unknown Source)
at com.businessobjects.wp.xml.XMLViaHttp.ping(Unknown Source)
at com.businessobjects.wp.xml.XMLSession.ping(Unknown Source)
at com.businessobjects.wp.om.OMSessionLoader.ping(Unknown Source)
at com.businessobjects.wp.tc.thread.PingRunner.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
BOE 3.1
Windows 2003 SP2
Tomcat 5.5.2
IIS 6
.net Framework 2
SQL Server 2005
Edited by: Terri Hoffmeyer-Ramos on Sep 12, 2011 9:57 PM

Could not provision the RemoteApp collection. Error: Could not join the domain. Unable to reach the domain.

Hi
I am trying to set up an Azure RemoteApp Hybrid solution.
I have created RemoteApp net and uploaded a custom image and all that is fine.
When I link my template to my Collection it fails after provisioning for about an hour.
I recive the following message: Could not provision the RemoteApp collection. Error: Could not join the domain. Unable to reach the domain.
The join domin works fine and I have tryed with account with different lvl of access to my AD.
Any suggestion how to solve this?

Hello Eric,
I am landing into the same Problem and i read your guidance on this issue. Let me answer it point by point.
1. Check the VPN state to ensure it is active or connected state:
Sundesh:My Azure RemoteApp Virtual Network after successfull S2S configuration shows as Ready. Is that what you mean by Connected State? Earlier to S2S, it was just under connecting state.
2. Verify your VNET configurations have proper IP address ranges
Sundesh: The VNET address range, the Local address range and DNS has already been verified twice. In fact the same address ranges(with exception to VNET) are working fine on a VENT config on Azure VM instance. Verified.
3. Verify your DNS IP configurations are valid, (often this is the problem)
Sundesh: Yes its done and verified
4. Verify the credentials entered for domain join are valid.
Sundesh: Tested these credentials by joining a regular Azure VM to domain and it works there.
5. Make sure your VPN endpoint that Azure RemoteApp service is connecting to is not blocking traffic.
Sundesh: Can you please let us know the specific port numbers that we need to consider and i can have it checked with the Network team
Thanks
SUndesh

CSCue18444 - A packet is unable to reach HSRP VIP in other VRF

Similar Messages

Maybe you are looking for