CSM Backup Server

Is the old CSS "sorry" or backup server supported on the CSM?
Trying to setup two web servers as active and backup behind a CSM. No load sharing.
Regards
Joe

yes, the backup option exist with the CSM
If you server1 active and server2 backup, here is an example
gdufour-cat6k-2(config-module-csm)#vserver www
gdufour-cat6k-2(config-slb-vserver)#serverfarm linux1 backup ?
WORD backup server farm name
gdufour-cat6k-2(config-slb-vserver)#serverfarm linux1 backup linux2
Gilles.

Similar Messages

  • Recently backing up my ipad onto my macbook, which is the backup server for all of my gadgets.  This includes all my photos and tons of music.  The macbook said it could not backup the ipad because there was insufficient disc space to do so. What now?

    I have a macbook operating OSX10.6.7.  Recently backing up my ipad which had lots of photos from a recent vacation.  I use this laptop as the backup server for all of my gadgets so it has thousands of photos and tons of music.  It just told me that it couldn't back up the ipad bc there wasn't enough disc space.  I was afraid that this would happen eventually.  What next?  Newer laptop with more space?  I'm not sure what files I could sacrifice to free up more space as most of these are important.

    What size hard drive do you have in your MacBook? The cheapest options are, a larger internal hard drive, or an external drive. Or you could get a cheap desktop PC and network to it for storage. I've got one that lives in the hall with 3 Terabytes (That's 3000gb) of storage.

  • How do I restore a Windows Backup Server backup recovery partition?

    I'm trying to test restoring a backup from our real server on a temp server.
    First, I was surprised it can't do a restore to a smaller drive because the original server is only 1/3 full (it wants to restore all the empty bytes too).
    Also it appears it wants to see that target partitions are already created.
    It wants to restore recovery to an EXISTING recovery partition and OS to an existing OS partition all with exact sizes.
    What if the old system died and I had to go to something new?
    Do I have to preinstall 2012 R2 on a bare drive so it creates the partitions?
    I've been down this path before, if it's not byte for byte match (offsets and all) it won't boot.
    I'm pretty sure I could restore just the OS partition and then do a Windows Repair which would move the master boot record onto the OS drive. But that seems wrong.
    What's the proper way to restore?
    Is Windows Backup Server to limiting?

    Hi,
    1. When trying to recover a partition, it requires a same or larger target partition. If you only backup data, there is no size limitation of the target partition. 
    2. We need an operation system to do the recovery. However you can perform a Bare Metal Backup so it could be restored without operation system - but it may force to backup more than partition C.
    If you have any feedback on our support, please send to [email protected]

  • The host is not authorized to connect to this Backup Server

    Hi experts,
    I'm trying to connect to a remote backup server S2_BS running on VM2 from a data server S1 running on VM1. When I issued following command in isql
    1> SYB_BACKUP...sp_who
    2> go
    Msg 7221, Level 14, State 2:
    Server 'S1', Line 1:
    Login to site 'SYB_BACKUP' failed.
    It failed to connect to its SYB_BACKUP (i.e. S2_BS is configured for SYB_BACKUP in this case).
    And I got following error in the error log of S2_BS:
    Jun 23 14:48:53 2014: Backup Server: 2.24.2.1: The host '10.43.13.204' is not authorized to connect to this Backup Server.
    Jun 23 14:48:53 2014: Backup Server: 2.6.2.10: Login information unavailable.
    I can ping VM2 from VM1 without any issue:
    $ ping 10.43.13.204
    PING 10.43.13.204 (10.43.13.204) 56(84) bytes of data.
    64 bytes from 10.43.13.204: icmp_seq=1 ttl=64 time=0.035 ms
    And have entry for S2_BS in /opt/sybase/interfaces on VM1:
    S2_BS
            master tcp ether 10.43.11.19 5002
            query tcp ether 10.43.11.19 5002
    And S2_BS is running correctly on VM2.
    I'm running ASE 15.7 SP110 on both VM1 and VM2.
    Could someone please let me know how to fix this?

    The message is due to a new security feature.  See Remote Dump Host Control
    for details on how to register your host with the remote backupserver.
    -bret

  • How to start sybase Backup server in windows 2008 r2

    Unfortunately i stop the sybase backup server.
    I try to start it again but i get problem in that.
    Sybase BCKServer_ASE_BS , Sybase SQLServer_ASE & Sybase XPServer_ASE_XP - These could not be start
    The error is in screenshot  can any one help at this please....

    To start I would suggest looking for more details in a) the backupserver errorlog file and b) the windows event log.  Hopefully one of these will provide more details as to *what* file could not be found.

  • Powerbook G4 as Media/Backup Server

    After a lot of research I still haven't figured out a plan that will suit my needs.  Im hoping someone here may be able to help out.  I have an old Powerbook G4 1Ghz with 1gig RAM running OS 10.3.9.  I don't use this machine currently, though it runs perfectly fine...minus the facts that it must be plugged in to operate and the OS is so old I cannot update any applications. 
    I'd like to re-purpose this machine as a media server and a backup server for my current Macbook Pro.  My idea is to have two duplicate external Hard-drives connected to the powerbook for redundancy.  I will store all of my media on these drives, as well as point time machine to these for backups for the MB pro.  I want AppleTV to use the powerbook as its source library.  My first problem is that iTunes on that machine is too old for AppleTV, and the OS is too old to upgrade iTunes to a workable version.  So I know I will have to update the OS to something more current. 
    The second issue is how to setup the backup redundancy.  In addition to any new backups from the MB Pro, I also have a ton of data/media Ive acquired over the years that I want to be able to access regularly.  Ive already been burned on a couple drives in the past and having at least two copies of everything is a must.  So what is the best solution for the backup discs?  Since this system is more than just a backup (it needs to also play the media files for AppleTV), does it make sense to do a RAID of some kind, or can I get by with just mirroring two duplicate external drives? 
    With all that said, what OS should I upgrade to, and how should I set up the redundant storage?  I apologize for the long-windedness and appreciate any feedback.  Thanks. 

    Whew, I wouldn't use Time Machine at all, nor Raid, more on both later.
    For OS, how much RAM does it have?
    Tiger Requirements...
    To use Mac OS X 10.4 Tiger, your Macintosh needs:
        * A PowerPC G3, G4, or G5 processor
        * Built-in FireWire
        * At least 256 MB of RAM (I recommend 1GB minimum)
        * DVD drive (DVD-ROM), Combo (CD-RW/DVD-ROM) or SuperDrive (DVD-R) for installation
        * At least 3 GB of free disk space; 4 GB if you install the XCode 2 Developer Tools  (I recommend 20GB minimum)
    http://support.apple.com/kb/HT1514
    See Tom's, (Texas Mac Man), great info on where/how to find/get Tiger...
    https://discussions.apple.com/message/15305521#15305521
    Or Ali Brown's great info on where/how to find/get Tiger...
    http://discussions.apple.com/thread.jspa?messageID=10381710#10381710
    Leopard requirements/10.5.x...
        *  Mac computer with an Intel, PowerPC G5, or PowerPC G4 (867MHz or faster) processor
    minimum system requirements
        * 512MB of memory (I say 1.5GB for PPC at least, 2-3GB minimum for IntelMacs)
        * DVD drive for installation
        * 9GB of available disk space (I say 30GB at least)
    There are workarounds if the 867MHz is the only hangup...
    http://sourceforge.net/projects/leopardassist/

  • Easiest way to Configuring backup server in oracle 8i

    I want to make a backup server i.e database for my existing database in different server. For example: My existing server completely crashed. I am having backup of os level complete backup only. Please note that not useing export file. Please suggest.

    It totally depends on your business requirements. If business requires something then you have to do it even though it is hard through the technology.
    Oracle does provide the following two main things to ponder on.
    1) Oracle Replication.
    2) Oracle Data Guard.
    -aijaz

  • Cluster and Backup server

    Hello guys;
    I want to use a cluster oracle server and another server in another place as a backup server to copy the database on line from the cluster server.
    If I want to make the backup server a primary server if something wrong happened to the cluster server.
    what the steps should I do? or if there is any document to read I'll be thankful
    thanks in advance

    Hi,
    What do you refer by saying cluster ? If you want to have a HA (High Availability) with Active/Passive cluster then you can go with 3rd party cluster vendor, like HACMP from IBM, ServiceGuard from HP and so on. If you want to create this with Oracle technologies then you are talking about Oracle RAC One Node. Of course you always go with Oracle RAC (Real Application Cluster) if you want to have a Active/Active cluster. These are in terms of cluster and High Availability.
    There is another point if you want to create a DR (Disaster Recovery) of you primary database then you would consider implementing Oracle Dataguard.
    Oracle has a rich documentation for blueprints and best practices, my sincerely advice is to get familiar with it:
    http://www.oracle.com/technetwork/database/features/availability/maa-090890.html
    Regards,
    Sve

  • Backup server desinging or deployment

    Hello guys,
    I have 1 backup & symantec mangement server in 2 different sites with 4 nics each (2 for management & 2 for backup traffic diferent Vlan
    Since this is fresh installation, in backup server we have configured 2 subnets192.168.1.x(internet) and 192.168.2.x.(backup) and added in the routing table to direct backup traffic to 192.168.2.x. for backup as we cannot keep 2 gateway in 1 server.
    Since, i have not set gateway for 192.168.2.x, we are not able to contact backup server from remote site.
    But, it works when i set the gateway, which i should not be doing.
    Any help would be appreciated.
    ndraj

    Hi,
    A computer should never have two default gateways. According to your description, I'm not quite sure about your network toppology.
    As what I understood, the server connect to both 192.168.1.x and 192.168.2.x, then subnet 192.168.2.x should be reachable even if you do nothing on routing table.
    If you add routing entry via "route add ...", it doesn't mean you have two default gateway. Only specific network will be send via this specific interface. In this situation, your provisioning should be correct.
    Hope this helps. 

  • Which Backup server version is required for Sybase cumulative dump/load

    Hello,
    To perform cumulative dump and load (supported from ASE 15.7 SP100 and up) with 3rd party API, what backup server version is needed?
    We use backup server API version 2.1, and sybackup.h does not have any definition for cumulative dump. This header file only defines DATABASE and TRANSACTION as command_type, so when "dump database foo cumulative" is issued, command_type becomes UNKNOWN.
    Since we support all the ASE versions from 15.0.3 and up, we ideally need a backup server API that works for ASE versions from 15.0.3 and also works with cumulative backup. Is there such an API version?
    Thanks,
    Ali

    What I'm told is that the version wasn't bumped because the changes shouldn't really affect the API functionality; the API module would still receive a byte stream and be able to store and return it regardless of the command_type.
    However, you can easily modify your sybbackup.h to reflect the new command_types.
    Replace the current command_type definitions with the following:
    #define TRANSACTION 0 /* transaction log dump or load */
    #define DATABASE 1 /* database dump or load */
    #define CUMULATIVE 2 /* Cumulative dump to dump or load */
    #define UNKNOWN 3 /* Pre-API SQL Server in use. Backup Server
                         has received a DUMP/LOAD command from a
                         SQL Server which is not passing the
                         'Command Type' toBackup Server. Therefore,
                         the Command type can not be determined. */
    #define DELTA 4 /* Delta dump to dump or load */

  • AnyConnect Client Profile Backup Server Configuration

    I'm trying to understand the use of Backup Server option in AnyConnect Client Profile
    Configuration > Remote Access VPN > Network (Client) Access > AnyConnect Client Profile > Edit > Backup Server
    (Screenshot attached)
    My questions:
    1. In what all scenarios do we add servers (ASA devices) in this tab
    2. If I have same information in two different locations (Site A and Site B) for AnyConnect user, can I add Site A-ASA and Site B-ASA into Backup Server tab as a failover mechanism for end user.
    3. Or is it only used to mention ASA devices configured in failover unit
    4. In case of failover unit, does it support stateful failover
    I could not find answers to above questions from Google search. So, asking here

    I think we need to be careful when we talk about failover. The original post was clearly asking about two different scenarios
    1) ASAs at two different sites
    2) ASAs configured as a High Availability failover pair (Active/Standby).
    The profile does work to provide failover in 1) but does not work to provide failover in 2).
    I do not know the authoritative answer to the question about IP phones use of the profile. I believe that the answer ought to be that yes the phone would receive the profile after its first connection and would use the backup server identified in the profile is the primary server was not available. That is a basic functionality of the AnyConnect client and if the phone is using the AnyConnect client then it ought to support that failover. 
    If someone does have an authoritative answer then please speak up. Several of us would like to know the right answer here.
    HTH
    Rick

  • Does DPM 2012 R2 still needs DataSourceGroups.xml and MaxAllowedParallelBackups key when using Hyper-V VSS Software Writer to backup Server 2012 R2 Cluster

    Hi,
    Does DPM 2012 R2 still needs DataSourceGroups.xml and MaxAllowedParallelBackups key when using Hyper-V VSS Software Writer to backup Server 2012 R2 Hyper-V Cluster with CSV's? Can't find a clear answer somewhere.
    Thanx for helping me out.
    DJITS.

    Configure CSV backups
    If you are running Hyper-V on Windows Server 2008 R2 and you’re backing up multiple clusters with DPM, you need to ensure that only one backup uses the same CSV at any one time. To do this, follow the instructions in
    Serialize virtual machine backups.
    If you’re using software VSS with Hyper-V on Windows Server 2008 R2, do the following
    Serialize virtual machine backups per node            
    Serialize virtual machine backups per CSV LUN            
    Have a nice day !!!

  • Unable to install the backup server using srvbuildres

    I am unable to install the backup server with resource file
    it gives weiored message which i didnot come across till now.
    Open Server Error: 16400.10.0: srv__e3_create_encrypt3_context: Unexpected failure in comn_keypair_create.
    Open Server Error: 16400.10.0: srv__e3_handshake: Unexpected failure in srv__init_encrypt3.
    Open Server Error: 16400.10.0: srv__handle_password_negotiation: Unexpected failure in srv__e3_handshake.
    Open Server Error: 16400.10.0: srv__e3_create_encrypt3_context: Unexpected failure in comn_keypair_create.
    Open Server Error: 16400.10.0: srv__e3_handshake: Unexpected failure in srv__init_encrypt3.
    Open Server Error: 16400.10.0: srv__handle_password_negotiation: Unexpected failure in srv__e3_handshake.
    this is all in the backuplog and it fails saying unable to boot the server and task failed and backup server not started.
    i see that the password encryption is not on i got that by running sp_helpserver <backupsever name>
    the staus i got when i ran sp_helpserver is "timeouts, no net password encryption, writable , enable login redirection"
    Please help me installing my backupserver.
    many thanks in advance.

    Please confirm that you're getting this error message while trying to CREATE the backupserver.
    The reason I ask is because you mention seeing these messages in the backupserver errorlog, but you wouldn't be getting any messages in the backupserver errorlog unless you were able to successfully install a backupserver.
    Also, what is your dataserver/backupserver version strings? (dataserver -v , backupserver -v)
    A quick google search turns up Note 1963584:Open Server Error 16400 in ASE Backup Server log when dumping a database. [References SAP note 1963584.]
    - same errors as you're seeing, but errors generated while attempting to perform a dump command (ie, backupserver has been installed and is up and running)
    - appears to be an issue when "net password encryption" is enabled/true for SYB_BACKUP; if you have net password encryption enabled ... what happens if you disable it?

  • Backup server on an ACE

    When creating a backup server on an ACE running A5(2.1), we're using the probe as the trigger. Once the primary real server has failed to the backup,  will it fail back to the primary server when the probe deems the primary server available?
    It's just  as well as the ACE manual documents the backup serverfarm, there's dearth of info on the backup server.
    Thanks.
    _ Greg

    Hi Greg,
    Backup rserver as you know would be configured with standby keyword. When primary server will be Operational (probe passed)
    - Existing connections on backup keep accessing backup.
    - For new connection requests ACE looks up sticky entries, if there's already an entry for backup server, the connection is sent to the standby rserver.
    - If a new client request (connection) doesn't match any sticky entry for backup rserver ACE forwards this request to primary.
    Let me know if you have any questions.
    Regards,
    Kanwal
    Note: Please mark answers if they are helpful.

  • Backup server recomendations

    We currently backup our 4 V880 servers using a 420R as backup server and an L25 tape jukebox on a dedicated gigabit ethernet.
    The L25 is in need of replacement and I thought an SL24 would be ideal but wondered what people might recommend as a backup server. The 420R already has some i/o issues and given the increased throughput of the LTO drives I thought this might need replacing as well. We use Netbackup software on the 420R is that has any bearing on the answer.
    regards,
    Paul

    Hi Greg,
    Backup rserver as you know would be configured with standby keyword. When primary server will be Operational (probe passed)
    - Existing connections on backup keep accessing backup.
    - For new connection requests ACE looks up sticky entries, if there's already an entry for backup server, the connection is sent to the standby rserver.
    - If a new client request (connection) doesn't match any sticky entry for backup rserver ACE forwards this request to primary.
    Let me know if you have any questions.
    Regards,
    Kanwal
    Note: Please mark answers if they are helpful.

Maybe you are looking for