CSM client device config

Hi,
On CSM Client >device> Access rules is showing the old config and not showing the active running config. Where as tools>preview configuration show me the running config.
How do I make the csm client show the running config.
Thanks.

Raj;
When managing devices with CSM, it is expected that all configuration changes made to the device are made via CSM. Any changes made via PuTTY will not be reflected within CSM without first re-discovering the device's policies.
The screenshot does not indicate a specific error, only that policy objects alreadty present in CSM were re-used with this device. For the yellow triangle items, you will need to highlight each item and reference the matching description pane. But from the overall status, the discovery was completed successfully with three warnings.
Thanks,
Scott

Similar Messages

WRT54G2: Searching For Client Device

After logging into the router's web interface, and trying to access the "wireless" settings screen, I get the following message:
Searching for your client device.
Please wait...
If you haven't clicked on the Wi-Fi Protected Setup button on your client device, please do so now.
Which then hangs when it's 99% completed.
I've posted a screen shot at
www.peeniewallie.com/2008/07/searching_for_your_client_device.html
(1) I set up this router several months ago, with two client devices. At the time, I did not get this message. Instead, I was able to access the web interface the way I always have with earlier Linksys routers.
(2) This happens if I access the router via wireless or Ethernet cable.
Any ideas on how I can get past this screen? The client devices are an iMac and MacBook Pro.
Message Edited by Robert Racansky on 07-10-2008 07:24 AM

Hard reset the router for 2-3 minutes ..... once resetted ... power down the router for few seconds ... power up & reconfigure the router ...
See if it works or not ....

Possible to use wired 10/100 ethernet for client device?

I can't seem to find an answer to this question...
I have a Airport Express that I connect to my stereo for streamed music in my living room. It's connected to my existing wireless network (Linksys WRT54G, WPA on). Works great. Airport Express is not configured as a network extender, just connected to the existing network.
With this configuration (or any other configuration) is it possible to connect a client device (in this case my Tivo) to the wired ethernet port on the Airport Express and have it function? I currently have a wire pulled down my hallway to connect my Tivo, I'd love to get rid of that wire. And since my Airport Express sits right behind my entertainment center, it would be great if I could use it in this fashion.
Anyone know if this is possible? I guess the short version is, can I connect anything to the AE's 10/100 ethernet port and have it be a member of my network?

Well, I gave it a try. It's not quite working though. I get through the entire WDS setup with no problems. Configuration went fine. Yes, it has to be WEP, not WAP for setup with WDS.
It doesn't work though. The light on the Airport Express stays solid green, showing a valid connection. But I can't see my AE anymore, in iTunes or from the Airport Admin Utility.
In the Airport Admin utility, I did set the ethernet port to be active. When I connect the AE to the router via the 10/100 port, everything works fine. But it simply won't show up with just the wireless. Maybe you can either connect the AE to your network via Wireless WDS OR the ethernet port can be active, but not both?

Requesting location information from a client device (7921G)

Hey gents,
Can a client device such as the 7921G gather its own location? I think I remember a configuration example for location presence information on a client. But unfortunately I can't find the configuration guide anymore.
Can anyone point me in the right direction, please?
Many thanks,
Sebastian Jeuk

This may help if you haven't seen it:
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/7_0/english/administration/guide/7921ovr.html

Cannot connect with CSM client

One of our clients has a problem with their CSM deployment, they recently upgraded their CSM version which is deployed on a vmware environment, the services are listed as running and the webservice is available on port 1714 - when he tries to access it with the CSM client he gets the error.
The client cannot connect to the authentication service."
* Please cofnirm whether the security manager server is running
I cant find any troubleshooting information for this specific issue - has anyone got any experience of this issue or what could be causing it.
Regards
Joel

I'm having the exact same problem. My work around is to run C:\Program Files (x86)\cscopx\setup\support\resetcasuser.exe, select option 1 and reboot the CSM box.
TAC said the issue was a GPO preventing the casuser for running batch, but we just modified the GPO yesterday and still have trouble.
Strange thing is twe did not have this issue when the backup job was failing.

SCREEN LOCKED error "Searching for your client device. Please wait..."

This error is locking my routers configuration screen. "Searching for your client device. Please wait... If you haven't clicked on the Wi-Fi Protected Setup button on your client device, please do so now."
Is there a fix for this issue without restoring to the factory defaults?.
Your work around is not an option because restoring the factory defaults and reconfiguring the router manually is would be too time consuming in our small office and can afford the downtime. Is there a fix for this issue without restoring to the factory defaults? This problem has been crippling many of the Linksys routers for some time now; just search the error on goggle.
Solved!
Go to Solution.

Power cycle the router. Unplug the power cord for 30 seconds and power it back on. If it still won't work, then you will have to reset and reconfigure the router. Please check the links below on how to reset the router and set it up for either cable or DSL:
Title: Resetting the router to factory defaults and changing the router’s password
Article ID: 19584
http://kb.linksys.com/Linksys/GetArticle.aspx?docid=1e97db4854604b0fb5cc8c0d74491e35_19584.xml&pid=8...
Title: Setting up a Linksys router for DSL Internet connection
Article ID: 3687
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...
Title: Setting up a Linksys router with Cable Internet service
Article ID: 3686
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3686

Considering iPad as our client device from enterprise's perspective

Hi all,
We are working on the proposal to consider iPad as our client device (to access our server), which needs to develop our own application for iPad, and then install that application on the iPad & then sell our system (both client device & server) to the customer. Don't know whether the above solution is appropriate or not (from both legal & technical perspectives). And, don't know what technial support we can get from Apple company.
It should be great if you can help to connect to the right person in the Apple company and forwarding some related documents/process to me.
Thanks.
Regards,
Stone

Hi all,
We are working on the proposal to consider iPad as our client device (to access our server), which needs to develop our own application for iPad, and then install that application on the iPad & then sell our system (both client device & server) to the customer. Don't know whether the above solution is appropriate or not (from both legal & technical perspectives). And, don't know what technial support we can get from Apple company.
It should be great if you can help to connect to the right person in the Apple company and forwarding some related documents/process to me.
Thanks.
Regards,
Stone

Time synchronization on client device

Is there any functionality in OLite 10g R2 which can maintain time synchronization on client devices (WM5 PPCs)? Obviously we could use some special application for such purpose, but it would probably need some user interaction, which we'd like to avoid...

Thanks for your post - I thought so :(
I already have one working solution, but I don't like it at all, because it's too complicated for such trivial task. I created new OTL command, which takes an application executable filename as parameter and launches it on the device (this OTL script also has to be present on the device). Than I created simple SNTP client application and published it on the mobile server for client devices. Now I can schedule a device command which launches this application to perform time synchronization with some time server on regular basis.

Bind client device to specific platform

Is there any method how to force a device to register on mobile server as some specific platform?
To speak concretely - I have 2 WM5 PDAs on my desk. The first device (Symbol MC70) has XScale CPU, the other has ARMV4 CPU (Acer n300). I used the same installation cab for both devices (the cab for PPC2003 XScale), but each device registers itself to different platform in Oracle Lite Mobile Server (Oracle Lite PPC2003 ARMV4 versus Oracle Lite PPC2003 XScale). So I need to publish each application twice to be available for both devices even though both devices/platforms are fully compatible - this is very uncomfortable for application evolution...
I would be probably able to change the platform in the mobileadmin.dm$all_devices or something like this, but this would be no system-solution and could maybe cause some problems on client side (the platform is also stored on client device in polite.txt file afaik - "TYPE=WINCE_XScale_CS_OLITE_2003").

What you are deploying is a Client Settings policy, not the client itself. This is akin to a Group Policy Object being linked to an OU. The machines in the collection which already have the ConfigMgr client will process those policies, but additional non-client
machines added to the collection will not automatically install the client.
As Torsten indicated, you can deploy the client to these machines using the manual client push method. Simply right click on the clients themselves (or the collection) and select Install Client. If doing it at the collection level, I recommend
against selecting "Always install the client software" in the wizard as it will force an unnecessary repair of the existing ConfigMgr clients. I would recommend testing this on one machine in the collection in question before attempting to do them in bulk.
Note that this requires that a Client Push Installation account be configured (Administration > Site Configuration > Sites > Client Installation Settings > Client Push Installation > Accounts tab) which has admin rights on the clients.
You *DO NOT need to enabled site-wide client push installation* to be able to use the Install Client method in the console. Enabling this will force the client to attempt installation on ALL systems that ConfigMgr sees.

1242AG WGB and Client Devices

Hi, is there a way to connect multiples AP to a root AP which is connected to the LAN and at the same time allowing client devices to connect to those AP. Perhaps, using 2.4 Ghz for client devices and 5 Ghz for WGB. Or perhaps using the AP as a repeater?

Daniel,
The simple answer is yes - the only thing that could change the way they are configured is - are you AP's LWAPP or Autonomous
HTH.

CSM clients on vlans

i have 6500 with 8 vlans..now iam going to implement a CSM with remote clients as well as all the local users on my 8 vlans. My questions are;
1. do i have to configure all vlans as clients?
2. is the VLAN where my CSM client is configured, be my only gateway?
thx a lot

HI,
regarding 1)
no normaly u have 1 client vlan and x server vlans
regarding 2)
this depends on the implementation if you use the brdiged mode the GW is placed in the "client vlan" if you use secure mode you have to take care that a default GW is configured on the CSM server side.
Regards,
Joerg

Home Sharing not indexing properly on client devices

Just installed updated to iTunes 11 on my WinXP box (I know, I know get with times.) I turned on Home Sharing for use with the iPads in the household. I can see(and I think play) all of the songs in my libary. The problem I am having is indexing. The iPads and iPhones only recognize about 1/50 albums and 0 artist tags for sorting purposes. The artist sort is empty. If I sort by songs and click on a song (again, all songs are there) they do in fact have album artwork, album and artist. But if I sort songs by artist, all but 1-5 sort under A (as if they had no artist tag). If I browse the songs the computer everything is behaving properly. All client devices appear to be getting the same index, which means problem is the host?
I am not sure whether it was working in iTunes 10 or not.
I have done the following:
Turned Homesharing off then back on on the host
Uninstalled/reinstalled iTunes
Repaired Bonjour
Deleted and re-added the library
Reset all devices including routers.
Any ideas?

Check this, perhaps it helps you to move your stuff over:
http://support.apple.com/kb/HT4527

Base device config storage in Ciscoworks

     Thanks again to all who have assisted in my previous question. We are being asked to find a place within Ciscoworks to store a device config for each of the type devices that we have on our network.
    So we would have 1 config for a 3750, a 2900, 3548's, etc. I was thinking we can label a config file, without addressing info, hostname, etc., on it and accomplish it that way. I could label one 3750 -12 port, 3750-48 port, etc., and just add the address info to the config when we deploy a config to a new device.
    Is this the best way to do it or is there another way that would work better? We have Ciscoworks LMS 3.2.
Thanks again for you help.
Dave Lehmann

You could use config labeling for this, but the recommended way to accomplish what you describe is with baseline templates. Go to RME > Config Mgmt > Compliance Mgmt > Template Mgmt. Create baseline templates for each device type that contains all of the general config commands you want. You can even add macro substitutions within the templates to be filled in during deployment. For example:
+ hostname [HOSTNAME]
+ snmp-server community ourReadOnly RO
+ snmp-server community ourReadWrite RW
+ enable secret 5 $1$...
During deployment, you would be given an opportunity to fill in the value of [HOSTNAME] for each device. Consult the online context-sensitive help for baseline compliance for more details.

CSM nat client sample config

Hi
We have one pair of CSM confiugred in bridge mode.
The user wants the servers to be able to access the VIP also.
Understand one solution is to use NAT client.
Anyone got a working config on NAT client for bridge mode?
Thanks!

natpool ....
serverfarm from-server2server
nat server
nat client
real x.x.x.x
ins
real x.x.x.x
ins
vserver from-server2server
vip x.x.x.x tcp
vlan
serverfarm from-server2server
ins
That's it.
Any question, let me know.
Regards,
Gilles.
Thanks for rating this answer.

IPhone Client not Connecting Until Device Config is "Saved"

Afternoon all, I've got a strange little issue with around 5 or 6 of our iPhone users who are setup with the Jabber client (voice, not IM). The client will operate fine for a few weeks then for no apparent reason stop connecting. Going into the troubleshooting page within the app I can see the connection status for directory and voicemail are fine but Desk Phone Integration and Internet Calling get stuck forever on "connecting". Experimentation found that going into the device's "Phone Configuration" page on CUCM and simply clicking "Save" with no changes made saw the device connect immediately and operate fine again for a few weeks until the same behaviour returned.
Is this a known issue or is it worth opening a TAC case?
We're on CUCM 8.6.2.20000-2, with the iPhone client 9.0.2.20078
Gary

Just in case it helps anyone, I have been working with cisco TAC and they just confirmed this is a new bug for us. It should be fixed on version 9.1 but we have 8.6 so going to that version is not an option for now.
They told me they will generate a patch for our particular version, with the help of the dev team, so the issue can be fixed.
Regards,

CSM client device config

Similar Messages

Maybe you are looking for