CSM - show run module # - diagnostic not supported

Hi, I´d like to know why show run module # (where is CSM) doesn´t show anything that I´ve configured before. I have CSM 3.1(5) and IOS 12.1(19)E1 with SUP2 MSFC2. Is this supported or a Bug ?
I also would like to know if it´s normal to appear not supported CSM module (6) when I use the command show module. This is because I can use CSM without problems. Is this supported or a Bug ?
Router#show module
Mod Online Diag Status
1 Pass
3 Pass
4 Pass
6 Not Supported
Thank you !!

Hi Joerg,
There´s no problem with show run if you want to see CSM configuration, but if you use IOS 12.2(14)SX1 with SUP720 you can use the command show run module # (where is CSM) and appears what you want.
I ´d like to know if this command is not supported with SUP2 and IOS 12.1(19)E1 or if it is a cosmetic Bug. I was searching in the Bug Toolkit and Release Notes and I didn´t find anything about it.
Could you give me a link where I can see "online diagnostics are not supported for CSM" ?.
Thank you.

Similar Messages

CSM-S "Configuration Sync is not supported by this card"

This is the message everytime I try to sync the cards.
NETCSP01#hw-module contentSwitchingModule 5 standby config-sync
Configuration Sync is not supported by this card
NETCSP01#
The are both installed into the same 6513.
Here are the configs
module ContentSwitchingModule 4
ft group 1 vlan 400
priority 30 alt 20
vlan 200 client
description Client Facing CSM Interface
ip address 192.168.100.6 255.255.254.0 alt 192.168.100.7 255.255.254.0
alias 192.168.100.8 255.255.254.0
vlan 100 server
description Server Facing CSM Interface
ip address 172.18.10.6 255.255.254.0 alt 172.18.10.7 255.255.254.0
alias 172.18.10.8 255.255.254.0
module ContentSwitchingModule 5
ft group 1 vlan 400
priority 20 alt 30
I am running the following version
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXE4, RELEASE SOFTWARE (fc2)
What am I missing?
Thank you!!

The configuration synch feature is supported from CSM-S version 2.1.1. I suggest you upgrade your device for using that feature.

CSM map/policy type dns not supported

When I configure dns maps or dns policies on my CSMs (WS-X6066-SLB-APC, HW 1.7, SW 3.2(2)) they say
"Map type DNS not supported by card, config accepted." and
"Policy type DNS not supported by card, config accepted."
What's the reason for that restriction? Will there be a software release that supports it? Didn't find anything about that in the release notes.
Many thanks in advance
Uli

I too have received this message in the past. I found that it was because I had not entered the GSLB license key into the CSM configuration (GSLB *is* an optional software license).
You enter your license key via a CSM variable. This configuration would work (substitute your own license key):
conf t
mod csm X <- where X is the slot # of your CSM
variable GSLB_LICENSE_KEY xxxxxxxxxxxxxxxxxxxxx
Substitute your license key for the row of 'x's. Then you will need to reboot the CSM. If you are running redundant CSM's you will need a license key for each.

IPhone 5 show message "charging is not supported" yet charge shows 100%

My iPhone 5 worked fine the first two nights. Then on the 3rd. morning (after charging all night) I see the message "charging is not supported with this accessory". I switched to old iPhone 4 wall charger with lightning cable, same message in the morning. Tried again with new lightning cable I received in the mail and original iPhone 5 wall charger. Worked fine first night and morning, but on 2nd. morning message "charging is not supported..) came on again, yet charge shows 100%. Each time I've plugged in lightning cable everything look ok (no "charging not suported" message). The message always appears in the morning after a nights charging.
Any ideas to try before I make an appointment with Apple Genius and drive 20 miles?
Thanks,
Bud P.

I took my iPhone 5 to the Apple Store and spoke with an Apple Genius. He checked out my iPhone and then I was told that that was not a hardware problem with the cable or charger unit, but that the message could appear if the phone was fully charged and left on too long after being fully charged. Since then I let the battery run down longer before I charge and then fully charge in the evening and unplug before I go to sleep. I have not had the message appear again since I did that.
bpiraino

HT4262 where can I find AirPort utility 5.6 - my old Airport express module is not supported by Airport Utility 6.1. I was directed by the program to this page, but I can not find that application anywhere on Apples's webpages.

Airport 6.1 does not support my Airport module (the second iteration), and tells me to download Airport Utility 5.6. I can not find it via the directed link from Airport utility 6.1 nor anywhere else on Apple's web site. It is also not on the App store.
Thanks in advance.

Welcome to the Apple Support Communities
To install AirPort Utility 5.6 on OS X Lion, follow these steps:
1. Download AirPort Utility from the Support website > http://support.apple.com/kb/DL1482 Don't open the installer after downloading that.
2. Open Terminal and copy:
cd ~/Downloads && pkgutil --expand ./AirPortUtility56.pkg ~/Downloads/AirPortUtility56 && gunzip -c<./AirPortUtility56/AirPortUtility56Lion.pkg/Payload | sudo tar -C / -xvf - "./Applications/Utilities/AirPort Utility 5.6.app"
3. Open Finder, select Go menu > Go to Folder, type /Applications/Utilities and open "AirPort Utility 5.6", so you will be able to use your AirPort on Lion

HT201272 if i downloaded hd tv shows but it is not supported on my itouch- what do i do?

if i downloaded items in HD format but I touch does not support this, what is the next step to get the seasons on the itouch?

Hello Jill146,
Thanks for the question, and welcome to Apple Support Communities.
The following articles may provide more information in relation to your question:
iTunes Store: About HD TV Shows
http://support.apple.com/kb/HT3455
iTunes: Purchasing and viewing HD videos
http://support.apple.com/kb/HT3209
HD videos feature a higher-quality picture, but are designed to be played only on your iPhone 4 or later, iPod touch (4th generation), iPad, iPad 2, computer, or Apple TV. HD content is offered in either 720p or 1080p.
When you purchase an HD video on a supported device or computer, only HD video will be downloaded. To download the SD version, you need to download the video again from your Purchased page. Conversely, if you purchase an HD video on an unsupported device, the SD version will be downloaded. Then, you will need to download the HD version from your Purchased page.
Thanks,
Matt M.

While upgrade to LWAP error : AP Radios not supported.

Hello Experts,
i am using upgrade tool and LWAP image c1100-rcvk9w8-tar.123-11JX1.tar.but still i am not able to upgrade to LWAP.
when i check detail log in upgrade tool its shows the AP Radios not supported.can somebody help me in this regard. Thank you in anticipation..
Below are the logs of the AP while doing LWAP upgrade
*Mar 1 00:00:05.712: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Mar 1 00:00:05.713: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:05.714: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:05.715: %DOT11-2-RESET_RADIO: Interface Dot11Radio0, Radio firmwar
e file not found, Trying hardware reset on radio
*Mar 1 00:00:12.706: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:12.707: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firm
ware file (flash:/5101.img) was found
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-2-RADIO_FAILED: Interface Dot11Radio0, failed - fir
mware file not found
-Traceback= 18F68 405868 3FDFB0 4072E0 129B34 129BDC 116F0 11904 1357B0
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:13.008: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid p
ower levels available
*Mar 1 00:00:15.059: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:15.061: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:16.061: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:16.617: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:16.617: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(8)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 30-May-06 17:41 by pwade
*Mar 1 00:00:16.618: %SNMP-5-COLDSTART: SNMP agent on host RH-W-D36-AP1121G is
undergoing a cold start
*Mar 1 00:00:16.642: Writing radio coredump to 'flash:/r0.rcore'
*Mar 1 00:00:17.334: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:31.891: Writing radio coredump to 'flash:/r0.rcore'
*Mar 1 00:00:37.051: Interface Dot11Radio0: not starting because stop-on-failur
e set
*Mar 1 00:00:37.058: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Mar 1 00:00:38.058: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
RH-W-D36-AP1121G#
Sh ver : and sh flash
RH-W-D36-AP1121G#sh fla
RH-W-D36-AP1121G#sh flash:
Directory of flash:/
    2 -rwx     3650405 Mar 15 1993 18:04:33 +00:00 c1100-k9w7-mx.123-8.JA2
    3 -rwx         272 Mar 01 2002 00:00:16 +00:00 env_vars
    7 -rwx      525184 Mar 01 2002 00:00:37 +00:00 r0.rcore
    5 -rwx          79 Mar 01 2002 02:12:52 +00:00 private-config
    4 -rwx        2072 Mar 01 2002 02:12:52 +00:00 private-multiple-fs
    6 -rwx        6626 Mar 01 2002 02:12:51 +00:00 config.txt
    8 drwx         128 Mar 01 2002 02:31:37 +00:00 c1100-rcvk9w8-mx
7741440 bytes total (1694208 bytes free)
RH-W-D36-AP1121G#sh ver
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(8)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 30-May-06 17:41 by pwade
ROM: Bootstrap program is C1100 boot loader
BOOTLDR: C1100 Boot Loader (C1100-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RE
LEASE SOFTWARE (fc1)
RH-W-D36-AP1121G uptime is 23 minutes
System returned to ROM by reload
System image file is "flash:/c1100-k9w7-mx.123-8.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1121G-E-K9     (PowerPCElvis) processor (revision A0) with 15038K/13
36K bytes of memory.
Processor board ID FOC08301UAW
PowerPCElvis CPU at 197Mhz, revision number 0x0950
Last reset from reload
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:11:93:F1:0E:BA
Part Number                          : 73-7886-07
PCA Assembly Number                  : 800-21481-07
PCA Revision Number                  : A0
PCB Serial Number                    : FOC08301UAW
Top Assembly Part Number             : 800-22053-04
Top Assembly Serial Number           : FHK0835V1J0
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1121G-E-K9
Configuration register is 0xF
RH-W-D36-AP1121G#
Also i reformated the iamge K9w7 again as i was only able login through CMD and while explorer still this error coming-
RH-W-D36-AP1121G Home Page
Cisco Systems
Accessing Cisco AIR-AP1121G-E-K9 "RH-W-D36-AP1121G"
Web Console - Manage the ap through the web interface.
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Show tech-support - display information commonly needed by tech support.
Extended Ping - Send extended ping commands.
Help resources
CCO at www.cisco.com - Cisco Connection Online, including the Technical Assistance Center (TAC).
[email protected] - e-mail the TAC.
1-800-553-2447 or +1-408-526-7209 - phone the TAC.
[email protected] - e-mail the HTML interface development group.
Appreciate your quick response and suggestions.

Hello ,
What are you refering by word Broken AP(1121series ) how do i confirm it is broken.
when i access it from CLI it looks completely fine m but when i do GUI access it shows the above GUI screen.
Can you Please help me to how to to check it is damaged.
Appreicate all your respnse.
Regards,
KA.

Shfsmount: shfs filesystem not supported by the kernel

I installed the shfs package through pacman, and there is a sshd running on the server. However, once I enter the command
shfsmount -P<port#> <user>@<server>:/var/www ~/websites/<server_name>/
(with the values in <> replaced by the appropriate values of course), I am able to enter the user's password and then the following error shows:
shfsmount: shfs filesystem not supported by the kernel
I have done some web/forum searching and have not found anything that helps. I have tried to build the shfs package through abs, but it seems to use an older kernel version (2.6.22) than I have (2.6.27) and the makepkg command errors out with a location-not-found type of error.
I would like to know if there is something in the abs files I need to change for it to use the correct kernel for building, or whether there is a way to get the repository package to work.
I look forward to your responses, and thanks for your time.

Well, using the sshfs method did work. However, shfsmount still returns the same error. When I installed sshfs, it also pulled in fuse, but doing
modprobe fuse
does not change anything that I can see. Is sshfs the same as shfs? They seem to be two different packages.
Also, I am using Xfce with Thunar as my file browser. When I do the sshfs method outlined in the wiki link above (which does work), Thundar acts like the folder where the mounted stuff is does not exist. When I hit refresh, the <server> folder will show up for a second, then dissapear. When I go through a text editor and open a file from there, the file opener can see the folder with no problems. I can look around in there with the terminal as well. Is there a way I can get Thunar to view that folder?

Microsoft health "notifications are not supported in this version of windows phone"

Adding some tiles to my Band shows the 'Notifications are not supported in this version of Windows Phone' error.
The affected tiles include calls, mail, Facebook, Cortana and Facebook messenger. My Lumia 630 is running on the version 8.10.14234.375 of WP8.1 Preview for Developers. Microsoft Health is Version 1.3.10424.1. Microsoft Health is allowed to run
in Background.

Never mind. It's actually working now.
The health app wasn't presenting me with a request to access notifications. Strangely on the 4th or 5th time opening the app it did.

Microsoft Band adding some tiles using Health app displays "Notifications are not supported in this version of Windows Phone"

Adding some tiles to my Band shows the 'Notifications are not supported in this version of Windows Phone' error.
The affected tiles include calls, mail, Facebook, Cortana and Facebook messenger. My Lumia 1520 is running on the latest version of WP8.1 Preview for Developers. Why is this the case?

Never mind. It's actually working now.
The health app wasn't presenting me with a request to access notifications. Strangely on the 4th or 5th time opening the app it did.

WDS not supported!

trying to connect between the new Airport Extreme and Airport Base station through the WDS, but when i try to join the Airport Base Station to the network of AEBS it shows this message " WDS not Supported"
I tried to update the software for the Airport base station but didnt work out !
is it a matter of compatility between Airport base station & AEBS?
please advice !

I wish I had read this post before I dropped $$$ on an Airport Express.
I returned home from the Apple store last night and spent a couple hours trying to configure a WDS with my Dual Ethernet Base Station. The Base Station simply refused to be configured in WDS mode. I ended up basically rendering my Base Station "dead" and Apple Support couldn't help me this morning reconfigure it - even after a couple of hard resets.
After approx. 1 hour on the phone, Apple Support told me to take it to the Genius Bar @ the Apple Store and the genius would try to reconfigure my Dual Ethernet Base Station so I could at least run Wi-Fi and Built-in Ethernet for my second computer.
In the meantime, I'm using my Airport Express as my new Base Station for Wi-Fi for my MBP.
The bottom line: Dual Ethernet base stations are becoming obsolete as further software updates advance from Apple, and they are WORTHLESS for WDS configurations.
I guess I'm wondering if it is worth it to even have to have the genius reconfigure it - if he can - and just drop the $$$ for a new EXTREME base station. Thoughts anyone on any of this?
Thanks!
Mike

Locale not supported

I updated tarantella native client to
version 3.42 for solaris2.8.
Now I get the error message
<Failed to process Tarantella server information>
at login. (version 3.3 works fine)
The command line shows warnings:
Warning: locale not supported by Xlib, locale set to C
Warning: X locale modifiers not supported, using default
It seems to be problem with locale settings, already described in a
previous newsgroup posting.
Setting LANG=en_GB (or other values) did not help.
Where I can get correct locale-files?
(Not included in the client distributions)
Thanks a lot,
JU

Please check your Apache Logfile.
The first connect to SGD by NC is to the Web Server. NC requested
serverinfo.html
Try in a Webbrowser:
http://<servername>/tarantella/cgi-bin/ttawebtop.cgi/tarantella/resources/login/sco/tta/boot/serverinfo.html
You will get an empty page. Look into the Source code of this empty page.
It show something like:
<html><head>


<title>Tarantella server information</title>











</html>
This is the information NC needs to connect to your SGDEE Server.
Check you can telnet to ConnectionHost Port AsadPort
TAB
"juschlue" <[email protected]> schrieb im Newsbeitrag
news:[email protected]...
Thank you for the solution that helped to solve
the locale problem. Unfortunally there is still
the error
<Failed to process Tarantella server information>
after approx. 20sec during login.
Our previous version 3.20 works correct
with the same server/login/pw.
Is there a way to identify (debug) the problem.
Thank you very much,
Jens-Uwe
Tillmann Basien wrote:
This is my answer to this issue:
http://www.tbsol.de/de/modules/news/article.php?storyid=64
TAB
\"juschlue\" <[email protected]> schrieb im Newsbeitrag
news:[email protected]...
I updated tarantella native client to
version 3.42 for solaris2.8.
Now I get the error message
<Failed to process Tarantella server information>
at login. (version 3.3 works fine)
The command line shows warnings:
Warning: locale not supported by Xlib, locale set to C
Warning: X locale modifiers not supported, using default
It seems to be problem with locale settings, already described in a
previous newsgroup posting.
Setting LANG=en_GB (or other values) did not help.
Where I can get correct locale-fil
es?
(Not included in the client distributions)
Thanks a lot,
JU

Getting error message as "Feature not supported" f...

I have made a master reset of my Nokia C5-00.After that I am unable to open my built in Facebook application.It's showing error as "Feature not supported". Because of it my facebook - mobile contact sync is also not enabled. How to resolve it ?
Thanks.

Assuming you already have the latest version, try re-installing the Firmware thru' Nokia Suite ..

Why does my Amazon Basics Lightning "not supported?"

Why does my Amazon Basics Lightning cable suddenly show that it is "not supported" with an error message after the most recent ios 8.1.1 update? It has worked for more than a year perfectly before this... it just started the error message this past week?

Maybe it's the cable. Do you get the same message when using the Apple supplied cable? Also, sometimes you'll get the message if the phone's lightning port is dirty with pocket lint or such. Use a toothpick or small brush to clean out the port.

10.7.3 external monitor "input not supported"

I have an external monitor connected with the Aplle VGA adaptor to my MBP.
It has been working fine for the last year.
Today I installed 10.7.3
And now I get the message "Input Not Supported" on the external display.
Not impressed.
Any ideas or do I have to roll back this update.
Cheers.

OK now it gets silly.
I have also had a problem, since I instaled Lion, that when I open my MBP the screen is black and no amount of encouragement will bring it to life.
So, I have to switch on my external monitor. My deskptop thern appears on the externam monitor, so I select "Detect Displays" from the menu bar and, kazam, my MBP screen comes to life and the desktop moves there.
It only remains for me to switch off the external monitor and wait for Apple to provide a fix.
Now, remember my current problem, in that the external monitor wil not work and shows "input not supported".
So today I opened my MBP and sadness, the screen is BLACK. So I switched on my external monitor and WAHEY! it worked and the desktop appeared on the external monitor.
Excited at the prospect that my problem had somehow magilcally fixed itself overnight, I selected "Detect Displays" and my MBP screen duly appeared and the desktop meved there.
The external monitor then stopped working and showed the message "Input Not Supported"
I also have a related VNC problem that is still outstanding, so I think it is fair to say that there are several issues around external monitors with Lion.

CSM - show run module # - diagnostic not supported

Similar Messages

Maybe you are looking for