CSS Load Balancing and AOL

We are load balancing a web site consisting of two servers using advanced-balance sticky-srcip. We have several customers that use AOL to access this site. They complain that their sessions are timing out. It appears that the souce IP address for the AOL users changes, thus causing the error. Is there anything we can do to prevent this from happening to AOL users?

Hi,
we are also hosting one of the biggest Internet Sites in Germany. We know this problem overall with megaproxys.
If you cannot insert cookies, try to change the sticky mask to 255.255.255.0.
With this setting, we have only a very small number of problems. Around 0,02 % overall.
Best Regards

Similar Messages

CSS load balancing and Remote desktop

hi all!
here is config:
!*************************** GLOBAL ***************************
cdp run
ip redundancy
ip route 0.0.0.0 0.0.0.0 10.12.248.1 1
!************************* INTERFACE *************************
interface 2/1
bridge vlan 2
interface 2/2
bridge vlan 3
!************************** CIRCUIT
circuit VLAN1
redundancy
ip address 10.12.248.101 255.255.248.0
circuit VLAN2
ip address 192.168.1.1 255.255.255.252
redundancy-protocol
circuit VLAN3
redundancy
ip address 192.168.7.25 255.255.255.0
!************************** SERVICE **************************
service Node1
ip address 192.168.7.23
active
service Node2
ip address 192.168.7.24
active
!*************************** OWNER ***************************
owner RenCap
content Cluster_Nodes
add service Node1
add service Node2
vip address 10.12.248.100
active
content Mngmnt_Node1
add service Node1
vip address 10.12.248.102
active
content Mngmnt_Node2
add service Node2
vip address 10.12.248.103
active
CSS_Primary#
Remote desktop of Node1 and Node2 is accesible, but only by local login and password.
How i can use tacacs for authentication on Node?
in other words, how can be LAN servers available from Node1 and Node2?

The document http://www.cisco.com/en/US/products/sw/secursw/ps2308/products_configuration_example09186a0080094848.shtml gives a complete configuration exmaple on Configuring TACACS Authentication with VPN Client.

Problem with WLIOTimeoutSecs in weblogic and apche CSS load balancer

Hi,
We are using Weblogic 11g, apache 2.2 and CSS load balancer for load balancing.
we have huge reports which take minutes to generate and hence we need higher value for WLIOTimeoutSecs. This works fine when we use server url but WLIOTimeoutSecs is not working when we use CSS load balancer.
We checked with our load balancing team they said CSS load balancer will not repost the request.
Here is the plugin configuration
<Location /*****>
SetHandler weblogic-handler
PathTrim /
WebLogicHost 'serevrip'
WebLogicPort 'port'
WLIOTimeoutSecs 3600
Idempotent OFF
WLProxySSL ON
DefaultFileName /***/***/index.jsp
Debug On
WLLogFile /***/***/***/***.log
</Location>
Could some please help me on this.
Thanks in advance
Regards,
Venkat

Hi Tarun,
The problem occurs when the SSL is enabled on apache. If I access the same URL over HTTP, the parameter WLIOTimeOut works fine.
Also I observed that, none of the parameters are getting applied to the plugin. I had switched on 'DebugConfigInfo'. With this the HTTP URL with ?__WebLogicBridgeConfig as query parameter returned the complete configuration. However when accessed with HTTPS the server did not return the configuration.
Is there a specific configuration to be applied when apache is used with SSL?
Thanks for your help,
Shashi

CSS Load balancing for Exchange Server

Hi,
I have CSS configured in single arm and I have multiple servers configured for load balancing and it is working fine but when I am configuring Exchange server for load balancing I am facing problem and applications and printer/scanners are not able to send the email through the Virtual IP address configured for exchaneg server.
But if we configured the real server IP in the printer/scanners they are able to send the email. While checking the logs on the exchange server, it is showing that request for the email so coming from the Exchange VIP configured in the CSS.
I can telnet on port 25 on the VIP address (192.168.200.237). But unable to send the email through this VIP.
Below is the configuration
service ENOC_EXCHANGE-1
ip address 192.168.200.235
active
service ENOC_EXCHANGE-2
ip address 192.168.200.236
active
content EXCHANGE
    add service ENOC_EXCHANGE-2
    add service ENOC_EXCHANGE-1
    vip address 192.168.200.237
    active
group EXCHANGE
add destination service ENOC_EXCHANGE-1
add destination service ENOC_EXCHANGE-2
vip address 192.168.200.237
active
DC-CSS01# show rule GIT EXCHANGE
Name:                EXCHANGE   Owner:                ENOC_GIT
State:                 Active   Type:                     HTTP
Balance:          Round Robin   Failover:                  N/A
Persistence:          Enabled   Param-Bypass:         Disabled
Session Redundancy: Disabled
IP Redundancy:    Not Redundant
L3:         192.168.200.237
L4:         Any/Any
Url:
Redirect: ""
TCP RST client if service unreachable: Disabled
Rule Services & Weights:
1: EXCHANGE-1-Alive, S-1
2: EXCHANGE-2-Down, S-1
=============================================================================
Please let me know how to solve this problem. System team is saying with the physical IP address it is working fine problem with Load balancing. I have even tried with the
Add service command in the group but didnt work for me. If i will remove the group command then I cant telnet on port 25.
I think this is related to single arm modle or some wrong configuration for the NAT.
Kindly assist me

Hi
Printers are on Vlan 80 ( gw is 192.168.80.1) and exange server is on vlan 200 (gw is 192.168.200.1) i have multiple vlan which will communcate with exchange.
I hv other servers on 200 subnet which are working fine in load balancing.
My CSS is single arm setup.
Please assist
Sent from Cisco Technical Support iPhone App

CSS Load Balancing with Billing Server

Hi Gilles
Could I have a CSS load balancing two servers and also have it communicate with a billing server across the network. If yes then how can I do it?
Regards,
Sushil

the CSS does not have the notion of billing server. A separate device - like the CSG - should be used if you need to collect billing info.
Gilles.

VPN load balancing and ASA !!!

Hi netpros,
I have a couple of questions about this and hope you might be able to assist me.
1.- Are VPN load balancing and failover (Active/Active) mutually exclusive ..? I mean they can't be used at the same time correct ..?
2.- How does the ASA handle the return traffic from the Internal LAN towards the remote client .. Because the cluster only requires ONE public virtual IP address, which will work for incoming packets .. but what about the return traffic which has knowledge of the DHCP scope's default gateway IP address only .. ? How gets the returned packet redirected from the default gateway IP address to the respective ASA internal IP address .?
3.- VPN load balancing only applies to remote clients using easy VPN technology (easy vpn client, hardware client , pIX using easy vpn client etc ) and does not work with static LAN-LAN tunnel .. correct ..?
Your comments are much appreciated

Hi Gilbert ..
1.- Thanks I wanted to make sure.
2.- I know that .. my question is in regards the return packets .. for example if I have the below IP schema:
ASA1: Public 20.20.20.20
Private 192.168.1.1
ASA2: Public 20.20.20.21
Private 192.168.1.2
Cluster virutal IP: 20.20.20.10
Default gateway for segment 192.168.1.0 is 192.168.1.1
Let's say that a vpn client tries to connect and the cluster instructs the client to connect to ASA2 20.20.20.21. The packets reach the internal server at 192.168.1.100. The internal server then sends the return packets back to the client by forwarding them to its default gateway which is 192.168.1.1 (ASA1). Here is my question .. how does the cluster handles this because the return packet are supposed to be directed to ASA2 192.168.1.2
3.- Any idea about this one ..?
Cheers,

Load balancing and rfc metadata repository in reciever rfc communication ch

hi.
i want to know the purpose of load balancing and rfc meta data repository in RFC communication channel.
and can u send me any examples on this load balancing.
waiting for your response.
bye.
regards.
seeta ram.

Hi Seeta Ram,
Load distribution is handled by the message server (there is one message server in an SAP System). When a user logs on, the message server assigns him or her to the application server that currently has the <b>smallest load</b>.
Well now you can understand that we use load balancing for better performance by distributing the work to different processes to balance or maintain the work load in SAP system.
For more information refer to this link
http://help.sap.com/saphelp_nw04/helpdata/en/28/75153a1a5b4c2de10000000a114084/content.htm
Regards
Sumit Bhutani

Advantages of using a webserver inbetween a load balancer and application servers

I am building out a new weblogic domain.
I am wondering which one of these configuration to go with:
1. Load balancer > weblogic servers
2. Load balancer > web server > weblogic servers
Could someone tell me what are the specific advantages of having web servers inbetween a load balancer and application servers (besides caching static data content and acting as a proxy)?
Thanks in advance
Srini

Other than hosting the static content, nothing much really. We have our load balancer go straight to WL for applications without static content and route to web server if there is static content. Easy enough to do it both ways, best of both worlds.

For a true load balancing and high-availability OHS, OPMN, and mod_oc4j

i have read this link of Enabling Clustering on oc4j9.0.4 standalone app server
http://www.oracle.com/technology/docs/tech/java/oc4j/htdocs/getstart.htm#1015479
To test the clustering, start up the load balancer by executing "java -jar loadbalancer.jar".
C:\OC4J_EXTENDED\j2ee\home>java -jar loadbalancer.jar
In a future release of Oracle Application Server, loadbalancer.jar will be
desupported. Because of this, we strongly suggest that you discontinue your use
of loadbalancer.jar in this release. Under high loads, loadbalancer.jar may not
function properly. For a true load balancing and high-availability solution,
please move to use OHS, OPMN, and mod_OC4J. For more information, please see
http://otn.oracle.com/products/ias/ohs/content.html
Balancer initialized...
what load balancer should i use for web clustering
<frontend host="balancer-host" port="balancer-port" />
balancer-host=localhost
balancer-port=80
for all nodes i mentioned same host and port in http-web-site.xml.Is it correct?
i completed all the steps and run http://localhost:6666/session/SessionServlet
i hit 3 times
in the different browser http://localhost:7777/session/SessionServlet
instead of coming 4 it starting from 1 only.

can i use this loadbalancer.jar or not?
how to mod_oc4j in standalone app server

Load balancing and High Availability topology

Our Forms 6i client-server application currently runs on Citrix farm of 20 Windows 2000 boxes (IBM Blade Servers 2 CPU and 2 Gig Memory).
Application supports 2000 users.
We are moving to AS 10g r2, forms 10g and the goal is to use same hardware, 20 Windows boxes (or less), for intranet web deployment.
What will be our best choices for application Load balancing and High Availability?
Hardware load balancer, Web Cache, mod-oc4j? Combinations?
Any suggestions, best practices, your experience?

Gerd, I understand, that you are running 10g web forms through the browser, but using Citrix for deployment. This means that in addition to Application Server and Forms runtime sessions, it will be separate browser session opened for each user. What the advantage of this configuration?
Michael, we are aware, that Citrix is not supported by Oracle as a deployment platform. That only means that prior contacting Oracle Support we have to reproduce the problem in standard environment. It was never been a problem to reproduce problem :) We were using Citrix as a deployment platform for Forms 6i client/server for 4 years, but now we are forced to upgrade to 10g.
We are familiar with various Load balancing options available. The question is which option is the most "workable" in our case.

2 ISP load balancing and redundancy

Hello!!
Our small company has about 40 branches spreaded within city. Branches are connected by optic wire supplied by our ISP. So in ISP our branches are located in one VLAN. From every branch we created VPN tunnel to our server room in central office. Central office is like a cetner point. If optic wire fails to central office, there would no VPN tunnels and no network to all branches. Moreover, all the traffice goes through central office.
Now we decided to pave one more optic line to our central office. And that will increase bandwidth and redundancy.
Private network topology: There are no default gateways and ip-addresses. For examle, at first branch I will plug computer directly into media converter and at the second branch plug another computer to the media converter. After that this two computers became in one network. And can assign any ip addresses to them.
What I have: our firewall do enough work, don't want to overload it. But we have some free ports in our new cisco 3750. The question is how to do load balancing and redundanccy? Can it do load balancing according to traffic? And how load balance incoming traffic? For example, connection was established from branche's router, how this router will choose through which line make connection? By the way, at all branches we use noisy cisco
3700 series routers.

Sorry for upping 1 year old threat.
We talked to our Network Provider. They said "these two cables are coming from two different places, so there is no way to use etherchannel. You must use active-standby solution."
Relying on STP we just put two cables into 3750 stack. But with default STP settings, connection was very unstable, many packet losses and disconnections. So we found easy solution with "flex links", making one interface backup of the other. And only now I recognized that this is not a failover solution. Because, if network beyond media converter will down, link from media converter to switch would still up.
What could I do to make our L2 WAN redundant? Are there any additional STP settings.

Load balancing and Failover

Hello,
We are wondering how load-balancing and failover of tpcall() work with
WTC:
The scenario:
We have one WLS Domain and two Tuxedo Domains. The Tuxedo Domains offer
the same set of services.
In the bdmconfig.xml, we specify connection_policy as 'ON_STARTUP' for
both Remote Tuxedo Domains. We also Import (T_DM_IMPORT) the same
Tuxedo Service from both Tuxedo Domains.
Questions:
1. Is there any load-balancing of the tpcall between the two Domains? If
so, is it round-robin? If round-robin, what determines the order?
2. If it is ONLY Failover, what determines the order of the tpcall? And,
is the Failover automatic? Or do we need to code for retry on failure?
3. ON_DEMAND vs ON_STARTUP: Does ON_DEMAND drop the connection to the
remote domain upon tpterm? And does ON_STARTUP use a pool of
TuxedoConnection objects?
4. Are there any configuration parameters for
'max_number-of_connections? What determines how many simultaneous
connections can be made?
Thanks,
Suresh Mohan.

Hi Suresh,
The following are my answers to your questions.
Suresh Mohan wrote:
Hello,
We are wondering how load-balancing and failover of tpcall() work with
WTC:
The scenario:
We have one WLS Domain and two Tuxedo Domains. The Tuxedo Domains offer
the same set of services.
In the bdmconfig.xml, we specify connection_policy as 'ON_STARTUP' for
both Remote Tuxedo Domains. We also Import (T_DM_IMPORT) the same
Tuxedo Service from both Tuxedo Domains.
Questions:
1. Is there any load-balancing of the tpcall between the two Domains? If
so, is it round-robin? If round-robin, what determines the order?Yes there is a load balancing between two remote Tuxedo TDomain Gateways.
The algorithm is random, not RR. Over time this should give equal
opportunities to both remote TDomain.
>
2. If it is ONLY Failover, what determines the order of the tpcall? And,
is the Failover automatic? Or do we need to code for retry on failure?The load balancing is always there. The failover is automatic. When a
connection to a remote TDomain encountered a problem (ie network) the remote
domain will be put on retry open connection (in ON_STARTUP) and the load
balancing will not select it until the connection re-established.
However, the tpcall() that encountered the error will not be retried to send
to different destination. It is up to the application to decide whether it
want to resend. Any requests called after the error will not select the
failed Remote TDomain.
>
3. ON_DEMAND vs ON_STARTUP: Does ON_DEMAND drop the connection to the
remote domain upon tpterm? And does ON_STARTUP use a pool of
TuxedoConnection objects?TPTERM() only terminate your application session to WTC. WTC still maintain
a secured T-session to remote Tuxedo TDomain. WTC does not use a pool of
TuxedoConnection Objects, the object stored in the JNDI refers to WTC.
>
4. Are there any configuration parameters for
'max_number-of_connections? What determines how many simultaneous
connections can be made?No. As described in #3, there is no need to use connection pool in WTC. WTC
uses session and virtual circuit design concept as Tuxedo TDOMAIN, the
logical pool is created/destroyed dynamically. That is the reason why you
can have a lot of TPACALL() outstanding at the same time. (The limitation is
the availability system resource.)
>
>
Thanks,
Suresh Mohan.Regards,
Hong-Hsi :-)

Discussion on load-balance and load-sharing

Hi, I found a article, which discuss the difference between load-balance and load-sharing. I think the explanation is pretty good, please see below. But I still have a question: how can we decide to choose one the both balance in the production environment ? Thank you
"In short, load balancing tries to distribute traffic evenly over multiple paths, whereas, load sharing intends to do it (for the lack of a better term) equally. True load balancing is difficult to achieve. For example, let's say there were two links (100 mbps and 300 mpbs) and a router needed to send out 600 mbps of traffic. Load balancing would distribute the traffic evenly, sending 300 mbps on each link. On the contrary, load sharing would divide the traffic equally based on the available resources, sending 200 mbps on the slower link and 400 mbps on the faster one. "

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
That's not how Cisco uses the terms, and generically they are often used almost interchangeably.
Cisco uses load balancing as the catch all for how a single L3 device routes across multiple paths to the same destination. Equal metrics or equal actual load distribution are not required. Most often, load balancing will be discussed with ECMP, but unequal path loading balancing will include Cisco's proprietary IGPs, such as EIGRP.
Cisco uses load sharing when using multiple paths when a single L3 devices doesn't normally route across multiple paths or multiple L3 devices are involved. Cisco load sharing discussions usually revolve around BGP.
Generically, I would say load balancing has more of a dynamic aspect to it, i.e. something is trying to actively balance traffic across multiple paths, while load sharing might mean multiple paths are utilized but not actively dynamically balanced.
I'm unsure what's your question with a production environment.

Load Balancing and Failover with 10G Standard Edition

Hi,
I am new to Oracle Replication and need some help setting up replication for load balancing and failover. Is this possible using Oracle 10G Standard Edition? I plan on having all updates done on the master site and both databases will be for reads. In case of failure of the master site, I would need to be able to failover to the other database.
Also, if anyone knows of any documention for Basic Replication in 10G, please let me know.
Thanks.

Simple nnapshot replication of data would require significant manual effort to configure to load balance or failover. One the load balancing side, you would generally be limited to to static load balancing-- assigning half the users to one machine and the other half of the users to the other machine, regardless of who is actively using the machine. Failover would be a significant manual effort, particularly to bring the failed machine back into the cluster. You would be implementing the guts of multi-master replication.
Frankly, if you actually have a system which is valuable enough to need load balancing and disaster recovery, I'm going to wager that it will be far cheaper even in the short run to buy more boxes and/or enterprise edition licenses than to try to implement this sort of thing yourself. In the long run, it will be far cheaper, since it will be far easier to maintain. Building all this yourself would probably be penny wise and pound foolish.
Justin
Distributed Database Consulting, Inc.
http://www.ddbcinc.com/askDDBC

Load balancing and RFC problem

Hi!
I have a problem regarding load balancing and RFC's. We use the follow function in librfc32.dll (from VB6) for RFC calls: RfcOpenExt It's working fine no problem, but from now on we will have to use the this funcion due to load balancing: RfcOpenExtV3
The only difference between the two functions is the parameters. RfcOpenExtV3 has 5 additional parameters:
intLoadBalance1, strLbHost1, strLbSysName1, strLbGroup1, intSapGui1
I asked our tech guys for the details so that I can set up the parameters (double check everything) and the RfcOpenExtV3 doesn't working. Return value is zero.
Have somebody faced with this issue before?
Thanks in advance!

Hi,
1. Probably this link may help.
[http://help.sap.com/saphelp_nw04/helpdata/en/22/042f18488911d189490000e829fbbd/content.htm]
Especially see the function parameters on this page,
which are the bottom.
regards,
amit m.

CSS Load Balancing and AOL

Similar Messages

Maybe you are looking for