CT5508 for two networks

Hello
Following customer request/desire I am exploring a "strange" CT5508 config.
Before diving in to it deeply I would like to know if my idea is possible at all.
This is what I need to start from:
1. Network is divided in two pieces , let's say "LEFT" and "RIGHT". The two pieces can only communicate through Firewall.
2. CT5508 will be installed physically close to two switches, one in each LEFT and RIGHT network.
3. Access Points will be present in both LEFT and RIGHT network and need to be controlled by single CT5508
4. We need to keep wifi/capwap traffic in both networks as much as possible separated
This is my idea:
1. No LAG
2. Have CT5508 SFP Distr Ports 1 through 4 connected to switch in LEFT network; ports 5 through 8 connected to switch in RIGHT network
2. Have AP Manager intf 1 through 4 associated to distr ports 1 through 4
IP Addresses of AP manager Intf 1 through 4 from IP Subnet 1 and VLAN LEFT
3. Have AP Manager intf 5 through 8 associated to distr ports 5 through 8
IP Addresses of AP manager 5 through 8 from IP Subnet 2 and VLAN RIGHT
4. Have different DHCP servers assigned/defined for LEFT and RIGHT network.
With this setup the question I can not answer from the CT5508 documentation is this one:
DHCP discover copies from AP in "LEFT" network come in over distr interfaces 1 through 4.
On which distri ports will CT5508 reply/offer to this DHCP discover from AP?
I hope this reply to go out over only distr ports 1 through 4 so that the DHCP-based Controller selection in the AP can select among AP manager intfs dedicated to the LEFT network.
Correct?
Going one step further: is this approach compatible with e redundant controller setup?
Thanks a lot for your help and any observation/warning on the subject.
Regards
Fred

Not possible, if you do LAG, all physical ports connect to a single switch (if dual switch, then it has to be VSS pair)
If customer require this sort of seperation, advise them to buy two WLC
HTH
Rasika
**** Pls rate all useful responses ****

Similar Messages

Setting up PIX515E VPN for two networks

Hello,
We have a PIX515E and I want to set it up so it can serve client VPN connections for a network on the inside interface and also for a network on the dmz interface.
On a client machine we set up the ip address of the PIX in a VPN connection and the user can log on using credentials and domain. Now the PIX has to look up credentials using RADIUS, but some users are known on domain A (inside interface) and some users are known on domain B (dmz interface). Domain B is completely different and uses other internal ip addresses, dns servers, ip pool etc.
Already I have set up VPN for the inside interface and that was easy and it works ok.
But can I create such a configuration? We only have one DSL line and we want both networks (domain A 192.168.1.x and domain B 192.168.10.x) to go through this PIX.
Your help is more than appreciated!
Regards,
Frank

rob,
i don't know your budget requirements, but here is a relatively easy solution:
http://www.apple.com/server/macosx/features/networkingvpn.html
and here is an OSS solution that will take a bit more work (but should run on an older box with bsd, linux, or os x running on it):
http://openvpn.net/
cheers,
b

One server for two networks

Hello,
I do not already have a Mac Server but I'm planning to buy one, but first of all I got a question.
Is it possible (if the server has two or more ethernet ports) to divide the services on the different ports ?
In my example I want to represent my homepage and other web services on the one ethernet port, that is connected to the web and on the other port I want to enable screen sharing, xgrid and so on to support the local network. I now want to know if it is possible to set up different options for every ethernet port.

Is it possible (if the server has two or more ethernet ports) to divide the services on the different ports ?
You can have (and use) as many ports as you like. Most of my servers have 4.
The issue is in controlling the services. By default, each service will typically listen on all interfaces, meaning they're available from all networks.
To do what you want requires a little tuning of each service to tell it how and where to run. The configuration is based on the service (which ports to run on) rather than the port (which services to support).
The specifics varies by service. It''s easy, for example, to do this with Apache - just tell it the IP address for each site and you're done. It's relatively easy for most of the file sharing protocols. Off hand, I can't think what's involved in ARD or XGrid.
Worst case, even if there isn't an easy mechanism for binding a service to one port, there's always the firewall which you can use to block traffic on the ports you don't want. Not a perfect solution, but it does help.

NO internet in the network except for two computers after installing ASA 5505

Hi Guys,,,
I dont know if any of you guys had a problem like this... I installed a CISCO ASA5505 with 50 user license to my network as the gateway firewall. So ASA is acting as the gaeway router which is connected to a fibre circuit and also it gives DHCP to the network. The strange thing is that except for two computers rest does not have internet. I also have an asterisk phone system which works fine..
I tried everything.... static IP's DHCP, DNS nothing worked. But strange enough two computers works fine and have internet.. but are no special computers. One is Win XP and the other one is Win7. When I troubleshoot the problem in win 7 on one of the computers it says
"The remote device or resource won't accept the connection"
I have no idea now... any help would be great...
Thanks in advance

Hello Amal.
I hope the gateway of the comupters are configured as ASA.. Are you able to ping your gateway from the PC where you dont have access to internet and also check whether the translation is happening on ASA when you are trying to access the internet ( show xlate | i 'local ip'
It would be great if you could share the ASA config as well
regards
Harish.

How does this happen: The picture of recent apps you get when double clicking the home button showed in Settings-Wifi that I had been connected to a network I have not been near for two months. Its not a recent "image" of Settings-Wifi. Can anyone explain

How does this happen: The picture of recent apps you get when double clicking the home button showed in Settings-Wifi that I had been connected to a network I have not been near for two months. Its not a recent "image" of Settings-Wifi. Can anyone explain?

Greetings,
I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
Good Luck - Cheers,
M.

I am using an Airport Extreme for wireless and a Netgear VPN Switch for wired connections. How do I get the two networks to connect?

I am using an Airport Extreme for wireless and also have a Netgear VPN Switch (FV5318) for internal wired ethernet connections. How do I get the two networks to connect to each other?

Tesserax, I would like to keep the Airport Extreme in nplace before the Netgear FVS318 switch because I am using all of the 8 ethernet outputs distributed to 8 differerent locationsl This way I can just use one of the LAN outputs from the Airport to feed the FVS318. Here is what I think I am hearing you say:
Tne reason why the wired and wireless devices are not communicating is because the FVS318G is also a DHCP server and in conflict with the AEBS.
To remedy the situastion here is probably what I need to do in order:
1. Change the LAN IP Address of the Netgear FVS318G to be the same subnet of the Airport Extreme.
2. Then, disable the Netgear FVS318G as a DHCP server.
3. Make sure the ethernet cable from the LAN port of the Airport Extreme connectis to the LAN port of the Netgear FVS318G.
4. Restart everything.
Can you provide me the steps I need to take to get the right IP addresses from the Airport Extreme to put into the Netgear to fix the conflict? I have the Airport Utility. I also have two airport express hot spots, and two Apple TVs in addition to computers attached to the 8 ethernet lines.
Thank you.
Steve

How to do Apache configuration for two different domains

Hi ,
I was just trying out some clustering workshop on weblogic. I faced a issue..here is the scenario :
I have two clusters :
Cluster1 : 3 managed servers (server1,server2,server3)
Cluster2 : 2managed servers (server4,server5)
I have two sample applications which i have deployed on these two clusters i.e app1 on cluster1 and app2 on cluster2.
These two aplications are deployed successsfully as i am able to open these applicatons from browser by calling the individual port of the managed server like : http://localhost:7003/app1.
Now i have installed a apache server on my laptop and configured the http.conf file.
Issue : I am not able to call both the application from apache. If there is only one cluster then it is working fine and for two application only one cluster (application) is working that too whose port is defined in the last.
Here are the contents of my httpd.conf file :
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.2> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.2/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do not begin
# with "/", the value of ServerRoot is prepended -- so "logs/foo.log"
# with ServerRoot set to "C:/Program Files/Apache Software Foundation/Apache2.2" will be interpreted by the
# server as "C:/Program Files/Apache Software Foundation/Apache2.2/logs/foo.log".
# NOTE: Where filenames are specified, you must use forward slashes
# instead of backslashes (e.g., "c:/apache" instead of "c:\apache").
# If a drive letter is omitted, the drive on which httpd.exe is located
# will be used by default. It is recommended that you always supply
# an explicit drive letter in absolute paths to avoid confusion.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to point the LockFile directive
# at a local disk. If you wish to share the same ServerRoot for multiple
# httpd daemons, you will need to change at least LockFile and PidFile.
ServerRoot "C:/Program Files/Apache Software Foundation/Apache2.2"
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available before they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule actions_module modules/mod_actions.so
LoadModule alias_module modules/mod_alias.so
LoadModule asis_module modules/mod_asis.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule authn_alias_module modules/mod_authn_alias.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
LoadModule authn_default_module modules/mod_authn_default.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
LoadModule authz_default_module modules/mod_authz_default.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_host_module modules/mod_authz_host.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
LoadModule authz_user_module modules/mod_authz_user.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule cache_module modules/mod_cache.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
LoadModule cgi_module modules/mod_cgi.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule dav_module modules/mod_dav.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule deflate_module modules/mod_deflate.so
LoadModule dir_module modules/mod_dir.so
#LoadModule disk_cache_module modules/mod_disk_cache.so
#LoadModule dumpio_module modules/mod_dumpio.so
LoadModule env_module modules/mod_env.so
#LoadModule expires_module modules/mod_expires.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule filter_module modules/mod_filter.so
#LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule imagemap_module modules/mod_imagemap.so
LoadModule include_module modules/mod_include.so
#LoadModule info_module modules/mod_info.so
LoadModule isapi_module modules/mod_isapi.so
#LoadModule ldap_module modules/mod_ldap.so
#LoadModule logio_module modules/mod_logio.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule mem_cache_module modules/mod_mem_cache.so
LoadModule mime_module modules/mod_mime.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
LoadModule negotiation_module modules/mod_negotiation.so
#LoadModule proxy_module modules/mod_proxy.so
#LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
#LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
#LoadModule proxy_connect_module modules/mod_proxy_connect.so
#LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
#LoadModule proxy_http_module modules/mod_proxy_http.so
#LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule rewrite_module modules/mod_rewrite.so
LoadModule setenvif_module modules/mod_setenvif.so
#LoadModule speling_module modules/mod_speling.so
#LoadModule ssl_module modules/mod_ssl.so
#LoadModule status_module modules/mod_status.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule unique_id_module modules/mod_unique_id.so
#LoadModule userdir_module modules/mod_userdir.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule version_module modules/mod_version.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule weblogic_module modules/mod_wl.so
*<IfModule mod_weblogic.c>*
WebLogicCluster 127.0.0.1:7005,127.0.0.1:7007,127.0.0.1:7003,127.0.0.1:7103,127.0.0.1:7104
MatchExpression /app1
*</IfModule>*
*<Location /weblogic>*
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007,127.0.0.1:7103,127.0.0.1:7104
DebugConfigInfo ON
PathTrim /weblogic
*</Location>*
*<IfModule mod_weblogic.c>*
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007
MatchExpression /app2
*</IfModule>*
*<Location /weblogic>*
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007
DebugConfigInfo ON
PathTrim /weblogic
*</Location>*
<IfModule !mpm_netware_module>
<IfModule !mpm_winnt_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User daemon
Group daemon
</IfModule>
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin <adminurl>
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName <servername>
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs"
# Each directory to which Apache has access can be configured with respect
# to which services and features are allowed and/or disabled in that
# directory (and its subdirectories).
# First, we configure the "default" to be a very restrictive set of
# features.
<Directory />
Options FollowSymLinks
AllowOverride None
Order deny,allow
Deny from all
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# This should be changed to whatever you set DocumentRoot to.
<Directory "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs">
# Possible values for the Options directive are "None", "All",
# or any combination of:
# Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# Note that "MultiViews" must be named explicitly --- "Options All"
# doesn't give it to you.
# The Options directive is both complicated and important. Please see
# http://httpd.apache.org/docs/2.2/mod/core.html#options
# for more information.
Options Indexes FollowSymLinks
# AllowOverride controls what directives may be placed in .htaccess files.
# It can be "All", "None", or any combination of the keywords:
# Options FileInfo AuthConfig Limit
AllowOverride None
# Controls who can get stuff from this server.
Order allow,deny
Allow from all
</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<FilesMatch "^\.ht">
Order allow,deny
Deny from all
Satisfy All
</FilesMatch>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you do define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "logs/error.log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you do
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and not in this file.
CustomLog "logs/access.log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "logs/access.log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://<url>/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock logs/cgisock
</IfModule>
# "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin">
AllowOverride None
Options None
Order allow,deny
Allow from all
</Directory>
# DefaultType: the default MIME type the server will use for a document
# if it cannot otherwise determine one, such as from filename extensions.
# If your server contains mostly text or HTML documents, "text/plain" is
# a good value. If most of your content is binary, such as applications
# or images, you may want to use "application/octet-stream" instead to
# keep browsers from trying to display binary files as though they are
# text.
DefaultType text/plain
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402<url>/subscription_info.html
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall is used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
#EnableMMAP off
#EnableSendfile off
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
#Include conf/extra/httpd-mpm.conf
# Multi-language error messages
#Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
#Include conf/extra/httpd-autoindex.conf
# Language settings
#Include conf/extra/httpd-languages.conf
# User home directories
#Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
#Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
#Include conf/extra/httpd-default.conf
# Secure (SSL/TLS) connections
#Include conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
So here for the above configuration only app2 i am able to call and for app1 its saying "404 page not found".
Can soomebody help me in cofiguring apache so that i can call both the applications.
Thanks,
Ankit

>
<IfModule mod_weblogic.c>
WebLogicCluster 127.0.0.1:7005,127.0.0.1:7007,127.0.0.1:7003,127.0.0.1:7103,127.0.0.1:7104
MatchExpression /app1
</IfModule>
<Location /weblogic>
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007,127.0.0.1:7103,127.0.0.1:7104
DebugConfigInfo ON
PathTrim /weblogic
</Location>
<IfModule mod_weblogic.c>
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007
MatchExpression /app2
</IfModule>
<Location /weblogic>
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007
DebugConfigInfo ON
PathTrim /weblogic
</Location>
>
This configuration is weird little bit. There is MatchExpression /app1 and MatchExpression /app2 and at the same time two <Location /weblogic> sections. Are you sure you understand what that configuration stands for?
Try something like this ...
<Location /app1>
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007,127.0.0.1:7103,127.0.0.1:7104
DebugConfigInfo ON
</Location>
<Location /app2>
SetHandler weblogic-handler
WebLogicCluster 127.0.0.1:7003,127.0.0.1:7005,127.0.0.1:7007
DebugConfigInfo ON
</Location>
where /app1 and /app2 are contexts of your weblogic applications.
http://download.oracle.com/docs/cd/E11035_01/wls100/plugins/apache.html
http://httpd.apache.org/docs/2.0/mod/core.html#location

IPod 5th Gen doesn't find any WiFi signals after battery was dead for two days.

I recently bought an ipod 5th generation, it only has the selfie camera (no back camera).
My battery then ran out, and my iPod was dead for two days.
My iPod charging cable wasn't working, so i went out to buy a new one.
After charging it with the new cable, it would not connect to the internet.
My brother has a 4th generation ipod and his picks up and connects to the wifi signal we have here at home, but mine won't even pick up the signal, or any wifi signals period.
I looked around here on the Apple Support but found nothing that helped, I already reset my network settings.
Is there any way to fix this?

If not this
iOS: Wi-Fi or Bluetooth settings grayed out or dim
One user reported that placing the iPod in the freezer fixed the problem. A trick that works frequently with iPhones:
Settings > AirPlane Mode ON, Do Not Disturb ON
Power down and wait 5-10 minutes
Power up
Settings > AirPlane Mode OFF, Do Not Disturb OFF
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar
Then
Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Migrating from SonicWALL to RRAS - questions on functionality for business network setup & monitoring

At my organization we are planning to move away from using SonicWALL and using Microsoft Server 2012 RRAS to handle IPv4 NAT routing and VPN connections for remote employees. I am trying to plan for all the functionality I currently have in our
SonicWALL router, and I'm not familiar with the Windows equivalent for some features and/or if the available features will have all the functionality our organization needs. Additionally wondering if there is something better that you would recommend
in terms of ease-of-use / management from an IT standpoint.
Feature: Firewall
I assume that Windows Advanced Firewall can handle all the firewall settings that I would normally find in an enterprise router. Is this a correct assumption?
Feature: Content blocking
What Microsoft technology would I use for blocking certain content and websites from being viewed in the workplace network? Can Windows Firewall handle these two types of content blocking?:
Blocking websites by general content - i.e. block porn sites.
Blocking websites by specific URL
Feature: Network activity monitoring
In cases where the network is slow, what would I use to inspect what IP/MAC is hogging bandwidth? Currently on SonicWALL we are able to see which computer is hogging bandwidth, see what website is, how much bandwidth it is consuming. Can RRAS
handle this level of detail, or is SCOM / some other technology more well-suited? Should we use a non-Microsoft application (something like Wireshark) instead?
Feature: Network prioritization (QoS / bandwidth management)
Can we set certain network groups to have priority over others? For example, if we split our incoming network into two networks using RRAS, 192.168.50.x for data and 10.0.50.x for VOIP, I want the VOIP network to get priority in order to
ensure quality audio on all phone calls. I assume this is available in RRAS.
Basically I'm just looking to see what systems I need set up to satisfy these business needs. If anyone has any real-world experience let me know what your setup is like -- I'm curious to know!

"I assume that Windows Advanced Firewall can handle all the firewall settings that I would normally find in an enterprise router. Is this a correct assumption?"
Your statement as it stands is correct. In fact, Windows firewall will handle more firewall settings than those found in a
router. However, SonicWall is not just a router - it's a firewall. There is a big difference. Given that you are comparing Windows Firewall to a robust firewall, I agree with Dennis that you should either stay with SonicWall or
look at Microsoft's product. But, given that on the link Dennis provided, you will find that Microsoft is discontinuing UAG, you might want to stick with what you know - SonicWall. Or, you need to evaluate your needs more. Yes, Microsoft
provides a number of built-in capabilities that may address your particular needs. We can't answer that. But, if there are features you need that are not available via Windows Server, then it is best to get a product that addresses those needs.
.:|:.:|:. tim

How can I set up my Mac for two users to share photos, music etc

How can I set up my Mac for two users to share photos, music etc?

On the Mac with the libraries you want to share:
iTunes Preferences click on the Sharing tab and put a tick in 'Share by library on local network'.
iPhoto Preferences click on Sharing and put a tick against 'Share my photos'.
When launching the same apps on other Macs on the network the libraries should be available, listed on the left.

How can two networks from the same router be showing up at once?

Very confused here. I hooked up the linksys wrt54g and obviously it showed up as an available network. It is hard wired into one computer.
I then (on an unwired computer) went into the router to rename the network and reset the password.
Now, when I check for available networks, both are present (linksys and the renamed one)? How can this be?
Also, the linksys network has five bars connectivity and the new one I renamed only has two. How is that possible?
Thanks

1. Always configure your router from a wired connection. Never through a wireless connection. The wired connection is the only reliable way to be sure your configure your router and not a different one.
2. Vista and Windows 7 allow you to name a wireless connection different then the "SSID" used on the router. It also allows you to set up two wireless connections using the same SSID. Clean up the list of preferred networks on your computer. That should take care of this.

Is there a way to connect to two networks simultaneously?

Here is my scenario:
I am an audio technician who travels from venue to venue for work have to constantly switch between two networks to do my job. I use MAC OS w/ the most current version 10.9
Example:
99% of the time, there is venue provided wireless internet via DHCP, w/ no wired option available. I log onto it for all my internet related productivity. At the same time, I need to stay connected to a manual/static ip local network to remote & monitor audio hardware (wireless mic's, dsp drives, mixing consoles, etc). I have the ability to use either a wired or wireless connection for the local manual network (new airport express, or wired line).
I go to my network preferences in my system prefs and can see a green confirmation indicator that both networks are indeed connected. However, depending on which network i give priority to by "setting service order", the other network drops. For example, today Im using a wired line to remote/monitor my audio systems on my manual/static ip network and can stay connected as long as i set my ethernet connection at the top of the 'service order' list. As soon as I go to launch my Safari browser it says I am no longer connected to the internet, eventhough my network system preferences show I am still connected. The only way I can get the internet to connect is to reset the 'service order' and put wi-fi back on top. As soon as I do this though, my manual wired audio network loses it's connection.
I should note some settings. Today's networks:
wireless (internet):
ip: 10.100.1.159
sm: 255.255.0.0
router: 10.100.255.254
wired (audio network):
ip: 192.168.0.128
sm: 255.255.255.0
router: 192.168.0.1
Is there a way to stay connected to both, regardless of the 'service order'? I have a brand new airport express if putting something like that in-line helps in anyway.
Best,
Brian

Is there a way to stay connected to both, regardless of the 'service order'?
There can only be one active connection at any given time, no matter how many networks you may be connected to.

Connecting to two networks at the same time

Hi Kadin,
I am looking for the same answer for a long time. I have two situations that requires to connect to two different metworks and that is when I travel with my portable Linksys router WRT54GC .
1. I stay at a hotel with a wireless Internet network connection and I try to use the network to access the Internet and then (2) I also need to access my external Maxtor harddrive to which I am connected through my portable router WRT54GC .
2. I have an almost identical situation but instead of the hotel network now I have a brand new T-Mobil cell phone made by ITC, which is called Wings and it uses a new way to connect my laptop to the Internet by using a Windows Mobile 6 Internet-share connection, which basically connects my laptop to the T-Mobile network and assigns it a IP address.
The problem that I have is that in both cases I can connect to each one of the networks separately but not simultaneously.
Any advise as to how this can be done. I also tried the Wireless WET54G as a bridge with similar negative results.
Thanks,
Pole

Ok not real clear on your setup, but here is the "networking answer" why you can not connect to two networks.
A device must have an IP address on the same subnet of the device you want to establish a connection or an IP route must be known to the network routers, since your internal address are most likely in the reserved private range, no internet router is not going to know how to deliver the packets to the correct hosts.
the simple answer is assign a secondary IP address to the network adapter on your laptop.
In the windows IP address properties for secondary address you can not set a default gateway. Windows only has 1 default gateway.
good luck
jwm

How to web filtering via two network cards?

I have Installed Server 2008 and two network cards
on my pc. One LAN card for clients access and one for internet router. I need to share internet connection to my client computers with
web filtering. So how to do that? I need to block some sites to client access.

Hi,
According to your description, my understanding is that you want to use the WS 2008 to share Internet connection and provide web filtering function for internal clients.
Internal clients –(NIC1) WS 2008(NIC2) – Internet router – Internet network
Manually assign IP address, default gateway, DNS server, etc. on NIC2. Manually assign IP address, DNS server, etc. on NIC1.
Install Network Policy and Access Services – Routing and Remote Access Services. Detailed steps reference:
Install and Enable the Routing and Remote Access Service
https://technet.microsoft.com/en-us/library/cc770798(v=ws.10).aspx
Then open Routing and Remote Access and start configuration. Enable NAT on NIC2 to transfer IP address. Detailed steps reference:
Enable and Configure NAT
https://technet.microsoft.com/en-us/library/dd469812.aspx
Windows Server itself does not support web-based filter, third-party tools with application-layer firewall might be needed to realize this function. Configure WS as a router, it supports IP packet filtering, which specifies which type of traffic is allowed
into and out of the router. Reference：
https://technet.microsoft.com/en-us/library/cc732746(v=ws.10).aspx
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Why are my devices finding two networks with the same name in my house?

I have Verizon FIOS (Actiontech router) connected with an ethernet cable to my Airport Express. Everything works beautifully through all three levels of my house...except... there are seemingly two networks in the house...a 192.X network (I think that is the Actiontech router), and a 10.X network (I think that must be the airport express)...
Here is the problem...
My devices (MACS, i-PADS, wireless printers) sometimes connect to the 192.X network (usually on channel 11) and sometimes they connect to the 10.X network (usually on channel 1). If the computers & i-PADS are not on the same network as the printers, then I can't print because the computer can't find the printer.
With the printers, every time the power goes out it's a crapshoot to see which network they reconnect to...and I have not found a way to manually choose a network since both networks have the same name and password (and I think they have to be set up that way in order for the Airport Express to work properly with the Verizon router.
Any help would be much appreciated.
Thank you.

OK, thanks. Did you see the message I posted right after your previous reply? I'm copying it here. Would choosing option two below, "join a wireless network" vs. "create a wireless network" be similar (or the same) as running in bridge mode? Thanks.
Tried a different MAC in my house using Lion instead of Mavericks and was able to open a version of Airport Utility. I couldn't find the tabs as in your picture; however, I did find a box that says, "This airport express is set up to create a wireless network." Three options are then listed as follows:
1- create a wireless network (the one that is checked)
2- join a wireless network
3- disable wireless and connect to a computer or network using Ethernet
If I choose option two above, would that solve the problem?
Thanks.

CT5508 for two networks

Similar Messages

Maybe you are looking for