CT5760 HA Pair not Forming?

We just received a pair of wireless controllers, AIR-CT-5760-K9 and AIR-CT5760-HA-K9.
I've wired them together with the StackWise cable, as we typically do with our 3850s (top left <-> bottom right, bottom left <-> top right, screws hand-tightenend). However, they're not seeing each other, stack ports show as "down" and have no neighbors.
I can't find any documentation on what, if any, additional configuration or commands are necessary for the two controllers to form an HA stack.
Looking at the documentation, it implies that we need to be running 3.3+. The boxes, including the HA SKU, shipped with 3.2. That can't be right, right?

Okay... N+1 is supported on 3.2, if you want to run AP SSO, you need 3.3
N+1
http://www.cisco.com/en/US/docs/wireless/technology/5760_deploy/High_Availability.html
AP SSO
http://www.cisco.com/en/US/docs/wireless/controller/technotes/5700/software/release/ios_xe_33/5760_HA_DG_iosXE33.html
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

Redundancy not forming with wlc

Hi,
We have two wlc 5508 running vers 7.4.100.60. They are not forming redundancy pair & are in maintenance mode.
Both RP's are connected physically direct.
Few outputs are given here:-
(WLC01) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Primary
         Unit ID = 2C:11:5A:5F:C7:00
Redundancy State = Non Redundant
    Mobility MAC = 2C:11:5A:5F:C7:00
Maintenance Mode = Enabled
Maintenance cause= Negotiation Timeout
Redundancy Management IP Address................. 10.32.25.11
Peer Redundancy Management IP Address............ 10.32.25.12
Redundancy Port IP Address....................... 169.254.25.11
Peer Redundancy Port IP Address.................. 169.254.25.12
(WLC02) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Secondary - HA SKU
         Unit ID = 10:B3:21:3C:01:B0
Redundancy State = Non Redundant
    Mobility MAC = 10:B3:21:3C:01:B0
Maintenance Mode = Enabled
Maintenance cause= Incompatible Software license
Redundancy Management IP Address................. 10.32.25.12
Peer Redundancy Management IP Address............ 10.32.25.11
Redundancy Port IP Address....................... 169.254.25.12
Peer Redundancy Port IP Address.................. 169.254.25.11
(WLC01) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
(WLC02) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
In addition, other errors are also seen during the process.
Starting Redundancy: Starting Peer Search Timer of 120 seconds
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Please help with all possible suggestions. thanks in advance

Hi,
i cant see that you have permenant AP count license on both.
review the following document for licensing requirement on AP SSO
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#licensing

Can LC Designer produce a flat PDF, not form, as a template for dynamic content?

Can LiveCycle Designer produce a flat PDF, not form, as a template for dynamic content?

Yes that means LiveCycle Designer .....the XDP is an XML file that describes the template that you want. It is turned into a PDF by the Designer as well as the LC Server I mentioned. The Designer creates interactive content (not what you asked for), the server can do the same as well as flat PDFs. I mentioned the batch mode because that is how people generally use it or they use it for real time creation of the reports but it tends to be high volume (it is a server product so it will bepriced that way). You can create an XDP that has text and "floating fields" on it. Floating Fields are special in that you can merge data with the template and once the data is put into the field it is turned into text (non-interactive). This woudl be useful for testing (requires a hands on approach) but if there is any kind of volume that you are looking for this will not be useful. The server side can be automated so that no human intervention is required.
Paul

Download page will not form correctly

The webpage for downloading iTunes 6 does not form correctly. There is not a link to begin the download.

hi y'all!
if you're seeing a blank blue box on the itunes download page, the usual suspect is
b McAfee Privacy Service.
(it causes a similar problem on the ipod software updater download page, too.) see the McAfee entry here:
b noir, "the conflict apocrypha", 10:07am Aug 18, 2005 CDT
... and also see related posts in the thread by btabz and Blandine Catastrophe.
love, b

I have trouble with iCloud. I doest show my notes form my iPad?

I have trouble with iCloud. I doest show my notes form my iPad?

My car broke last week. Can you tell me what's wrong with it?

I have many pdfs that have the identical structure, but are NOT forms. How can I collect this data?

I have dozens of pdfs which have the identical structure, but are NOT forms. I would like to collect data across these pdfs to analyze. Is there a way to do this?

There are a number of ways that text can be extracted, but it may not be in the order that you'd expect or want. But if it's consistent in any case, you should be able to get at the content you're interested in. JavaScript can be used to loop through the "words" on a page, for example. I've used this approach for several projects that required data extraction.

Upload multiple files WITH correct pairs of form fields into Database

In my form page, I would like to allow 3 files upload and 3 corresponding text fields, so that the filename and text description can be saved in database table in correct pair. Like this:
INSERT INTO table1 (filename,desc) VALUES('photo1.jpg','happy day');
INSERT INTO table1 (filename,desc) VALUES('photo2.jpg','fire camp');
INSERT INTO table1 (filename,desc) VALUES('photo3.jpg','christmas night');
However, using the commons fileupload, http://commons.apache.org/fileupload/, I don't know how to reconstruct my codes so that I can acheieve this result.
if(item.isFormField()){
}else{
}I seems to be restricted from this structure.
The jsp form page
<input type="text" name="description1" value="" />
<input type="file" name="sourcefile" value="" />
<input type="text" name="description2" value="" />
<input type="file" name="sourcefile" value="" />The Servlet file
package Upload;
import sql.*;
import user.*;
import javax.servlet.*;
import javax.servlet.http.*;
import java.util.Map;
import java.util.HashMap;
import java.util.Date;
import java.util.List;
import java.util.Iterator;
import java.io.File;
import java.io.PrintWriter;
import java.io.IOException;
import java.text.SimpleDateFormat;
import org.apache.commons.fileupload.servlet.ServletFileUpload;
import org.apache.commons.fileupload.disk.DiskFileItemFactory;
import org.apache.commons.fileupload.*;
public class UploadFile extends HttpServlet {
private String fs;
private String category = null;
private String realpath = null;
public String imagepath = null;
public PrintWriter out;
private Map<String, String> formfield = new HashMap<String, String>();
//Initialize global variables
public void init(ServletConfig config, ServletContext context) throws ServletException {
    super.init(config);
//Process the HTTP Post request
public void doPost(HttpServletRequest request,HttpServletResponse response) throws ServletException, IOException {
    request.setCharacterEncoding("utf-8");
    response.setCharacterEncoding("utf-8");
    response.setContentType("text/html");
    PrintWriter out = response.getWriter();
    Thumbnail thumb = new Thumbnail();
    fs = System.getProperty("file.separator");
    this.SetImagePath();
     boolean isMultipart = ServletFileUpload.isMultipartContent(request);
     if(!isMultipart){
      out.print("not multiple part.");
     }else{
         FileItemFactory factory = new DiskFileItemFactory();
         ServletFileUpload upload = new ServletFileUpload(factory);
         List items = null;
         try{
            items = upload.parseRequest(request);
         } catch (FileUploadException e) {
            e.printStackTrace();
         Iterator itr = items.iterator();
         while (itr.hasNext()) {
           FileItem item = (FileItem) itr.next();
           if(item.isFormField()){
              String formvalue = new String(item.getString().getBytes("ISO-8859-1"), "utf-8");
              formfield.put(item.getFieldName(),formvalue);
              out.println("Normal Form Field, ParaName:" + item.getFieldName() + ", ParaValue: " + formvalue + "<br/>");
           }else{
             String itemName = item.getName();
             String filename = GetTodayDate() + "-" + itemName;
             try{
               new File(this.imagepath + formfield.get("category")).mkdirs();
               new File(this.imagepath + formfield.get("category")+fs+"thumbnails").mkdirs();
               //Save the file to the destination path
               File savedFile = new File(this.imagepath + formfield.get("category") + fs + filename);
               item.write(savedFile);
               thumb.Process(this.imagepath + formfield.get("category") +fs+ filename,this.imagepath + formfield.get("category") +fs+ "thumbnails" +fs+ filename, 25, 100);
               DBConnection db = new DBConnection();
               String sql = "SELECT id from category where name = '"+formfield.get("category")+"'";
               db.SelectQuery(sql);
                while(db.rs.next()){
                  int cat_id = db.rs.getInt("id");
                  sql = "INSERT INTO file (cat_id,filename,description) VALUES ("+cat_id+",'"+filename+"','"+formfield.get("description")+"')";
                  out.println(sql);
                  db.RunQuery(sql);
             } catch (Exception e){
                e.printStackTrace();
        HttpSession session = request.getSession();
        UserData k = (UserData)session.getAttribute("userdata");
        k.setMessage("File Upload successfully");
        response.sendRedirect("./Upload.jsp");
//Get today date, it is a test, actually the current date can be retrieved from SQL
public String GetTodayDate(){
    SimpleDateFormat format = new SimpleDateFormat("yyyyMMdd");
    String today = format.format(new Date());
    return today;
//Set the current RealPath which the file calls for this file
public void SetRealPath(){
    this.realpath = getServletConfig().getServletContext().getRealPath("/");
public void SetImagePath(){
    this.SetRealPath();
    this.imagepath = this.realpath + "images" +fs;
}Can anyone give me some code suggestion? Thx.

When one hits the submit button - I then get a 404 page error.What is the apaches(?) error log saying? Mostly you get very useful information when looking into the error log!
In any case you may look at how you are Uploading Multiple Files with mod_plsql.

Bluetooth pairing not working since Anna update

Hi there,
after updating my N8 to the [awesome] Anna my bluetooth connection is not working properly anymore.
- I cannot pair the phone from PC Suite -> phone; PC Suite respondes after timeout that the phone cannot be authorized. From the phone bluetooth icon I see that there is no connection attempt between PC and phone (although the phone is found when searching for bluetooth devices)
- I can connect from phone to PC direction -> If I do so, I always have to authorize the pairing. For every new sync between PC and phone I have to authorize my PC on the N8 which is very annoying.
I've tried to pair my N8 on another PC and it shows the same behaviour.
Any suggestions?
PC Suite 7.1.30.9
Windows XP SP3
Office PC (No admin rights)
Thanks, BR,
Stephan
Nokia N8 dark grey, Symbian Belle

Tried this but the issue is that the PC can't authorize the phone. The PC finds the phone as bluetooth device but the pairing results in a timeout because the phone does not respond.
Any other clues?
Thanks
<edit>
It seems like there are some bluetooth issues after updating to Anna since other users are reposting similar things (I assume the car audio issues might be linked to this issue too).
--> Not able to transfer media files form nokia E5 TO e63
--> bluetooth authorization after update anna
--> Nokia N8 bluetooth problem (maybe linked?)
--> Bluetooth: Pairing fails after S^3 Anna update (C6-01, 022.014)
--> Bluetooth Problem after Anna Update (maybe linked?)
--> Nokia C7 Bluetooth problem with Audi Bluetooth handsfree
--> C7 Bluethooth problem (with car) after Anna update
</edit>
Nokia N8 dark grey, Symbian Belle

OSB to SOA suite package not forming correctly

Setup is as follows:
AIX 5.3 on the box, 10 gigs ram, installation of the latest releases of OSB and SOA suite on top of weblogic. I've built out a couple of simple database queries in BPEL based off wsdls, dropped them on to the SOA suite server, used EM to open a test console and plugged in some search data. Search returns successfully.
I then open up OSB's console, create a business service to the endpoint on the soa server, and a proxy based off the same wsdl used in the BPEL construction which I then route to the business service. Both service and proxy are made with basic http for the protocol (not sure how to use the sb protocol, and not sure if that will fix the problem). Load the test console on the proxy service, which displays an xml form similar to what is used in the SOA suite. Fill out the same information, but the invoke returns BEA-380000. Following the invocation trace in OSB everything looks good in terms of package content.
Wondering if it might simply be a problem with how the OSB interprets XML from a wsdl, I piped the XML from the SOA suite into the OSB's xml field, but to no luck, same error. After some more testing and frustration,I put the SOA suite XML straight in to the form field in the OSB test console, and it worked. However, the package itself seems oddly formed, consisting of:
<soapenv:Envelope      xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/">
     <soap:Header      xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
     </soap:Header>
     <soapenv:Body>
     <soap:Envelope      xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
     <soap:Header/>
Which I've been told is basically double wrapping the package, which shouldn't work, and more importantly wont be generated when someone uses say SOAPUI to access our service on the OSB.
Now, on the SOA suite side of things. In EM console, I navigate to my BPEL process and can see the faults caused by the OSB. The same faults are also generated when binding to the OSB's endpoint with SOAPUI, but not when going directly to the SOA suite's endpoint. The error is the following:
oracle.j2ee.ws.saaj.soap.SOAPVersionMismatchException: Mime Header Content-Type: text/xml requires SOAP envelope namespace: http://schemas.xmlsoap.org/soap/envelope/: Mime Header Content-Type: text/xml requires SOAP envelope namespace: http://schemas.xmlsoap.org/soap/envelope/
And the payload sent shows as empty.
So to my best uneducated guess, it looks like the OSB wraps the payload in an envelope, and then unwraps it before handing it to the SOA suite, which expects the payload to be wrapped. Sadly, I'm still pretty new to the wsdl/webservice/oracle world, so I'm not even sure if that's an accurate representation. Any insight on what might be happening or how to get OSB to talk with SOA suite correctly would be greatly appreciated. Included below are the XML payloads I've used (minus a bit for confidentiality reasons). Apologies if the formatting doesn't work so nice for it.
OSB Generated (fails):
SOAP Header:
<soap:Header xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
</soap:Header>
Body:
<ns2:SyncEmployeeIDRequest xmlns:ns="removed" xmlns:ns1="removed" xmlns:ns2="removed">

<ns:PersonIdentificationAssertion>

<ns1:PersonBirthDate>
<ns1:Date>2008-09-28</ns1:Date>
</ns1:PersonBirthDate>

<ns1:PersonGivenName>string</ns1:PersonGivenName>
<ns1:PersonSurName>string</ns1:PersonSurName>
</ns:PersonIdentificationAssertion>
<ns1:DepartmentIDText>string</ns1:DepartmentIDText>
</ns2:SyncEmployeeIDRequest>
SOA Generated(works if plugged into OSB form field)
SOAP Header:
<soap:Header xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
</soap:Header>
<soap:Envelope xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
     <soap:Header></soap:Header>
     <soap:Body xmlns:ns1="removed">
          <ns1:SyncEmployeeIDRequest xmlns:ns2="removed">
               <ns2:PersonIdentificationAssertion xmlns:ns3="removed">
                    <ns3:PersonBirthDate>
                         <ns3:Date>2008-09-28</ns3:Date>
</ns3:PersonBirthDate>
                    <ns3:PersonGivenName>string</ns3:PersonGivenName>
                    <ns3:PersonSurName>string</ns3:PersonSurName>
</ns2:PersonIdentificationAssertion>
</ns1:SyncEmployeeIDRequest>
</soap:Body>
</soap:Envelope>
Working Request Document in OSB:
<soapenv:Envelope      xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/">
     <soap:Header      xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
     </soap:Header>
     <soapenv:Body>
     <soap:Envelope      xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
     <soap:Header/>
     <soap:Body      xmlns:ns1="removed">
     <ns1:SyncEmployeeIDRequest      xmlns:ns2="removed">
     <ns2:PersonIdentificationAssertion      xmlns:ns3="removed">
     <ns3:PersonBirthDate>
     <ns3:Date>2008-09-28</ns3:Date>
     </ns3:PersonBirthDate>
     <ns3:PersonGivenName/>
     <ns3:PersonSurName>ALastName</ns3:PersonSurName>
     </ns2:PersonIdentificationAssertion>
     </ns1:SyncEmployeeIDRequest>
     </soap:Body>
     </soap:Envelope>
     </soapenv:Body>
     </soapenv:Envelope>
If I can provide anymore information that will help shed light on this issue please let me know.
Thank you for your time.
~Nick

Problem solved. When I originally created my business service inside of OSB, I created it based off an endpoint provided by the SOA server. Instead, I went and did a mass import from a url, pointed it at the SOA server wsdl, and then built the web service off of that wsdl resource in the OSB. Now it works like a charm.

Xml Document is not formed correctly.. Help me..

Using the .xsd files provided to me, I created XMLBeans using the schema project in weblogic 8.1 sp2.
These XMLBeans are used to create a XML document in my Weblogic Integration process. The values in the xml document are retrieved from a database (which cannot administered/viewed by me). XML document was formed perfectly. But recently when I tried running the application again, I found that the xml is not created properly.
When I tried to print the xml message, it displays the xml message with the first letter changed from '<' to '<'.
eg.
<batch_document>
</batch_document> is displayed as
<batch_document>
</batch_document>
What may be the reason behind this change. Is it possible because of some invalid data from the backend? If so, what could be the data?
Is there any special characters which when inserted between the elements makes the document like this?
The code that creates the xml document looks like this ...
BatchDocumentDocument bDoc= BatchDocumentDocument.Factory.newInstance();
BatchDocument bd= bDoc.addNewBatchDocument();
System.out.println(bDoc.toString());
The print statement prints the xml message as
<batch_document>
</batch_document>
I would be grateful even if I am answered with any of these questions.
Thanks in advance.

Hello Elango,
Have you tried validating the instance document using the validate() method
-Raj
<Elango SV> wrote in message news:[email protected]..
Using the .xsd files provided to me, I created XMLBeans using the schema
project in weblogic 8.1 sp2.
These XMLBeans are used to create a XML document in my Weblogic
Integration process. The values in the xml document are retrieved from a
database (which cannot administered/viewed by me). XML document was formed
perfectly. But recently when I tried running the application again, I
found that the xml is not created properly.
When I tried to print the xml message, it displays the xml message with
the first letter changed from '<' to '<'.
eg.
<batch_document>
</batch_document> is displayed as
<batch_document>
</batch_document>
What may be the reason behind this change. Is it possible because of some
invalid data from the backend? If so, what could be the data?
Is there any special characters which when inserted between the elements
makes the document like this?
The code that creates the xml document looks like this ...
BatchDocumentDocument bDoc= BatchDocumentDocument.Factory.newInstance();
BatchDocument bd= bDoc.addNewBatchDocument();
System.out.println(bDoc.toString());
The print statement prints the xml message as
<batch_document>
</batch_document>
I would be grateful even if I am answered with any of these questions.
Thanks in advance.

Bootcamp boots in parallels but not form start up.

hi i was having problems installing bootcamp and installed it to my partitioned (partitioned by bootcamp installation app) side of the HDD it will load up perfectly within Parallels but not through the boot selection on start up and shows a error about no bootable something.
should i uninstall the bootcamp and parallels and try to install it again through the utility or how do i set it to be able to boot form start up to it withought a Virtual machine?

1. Remove the Parallels VM.
2. Remove the Bootcamp Partition using Bootcamp Assistant.
3. Create the Bootcamp partition again using Bootcamp Assistant only, build a USB as directed and if necessary.
4. Bootcamp Assistant will automatically boot to the Windows Installer and start it.
5. Install Windows as directed by the Installer.
What kind of problems were you having during the initial installation that made you switch to Parallels-based installation?

Clear canvas and not form

Hi,
I am having 2 canvas both content canvas in one form.
There are lov dropdowns to get the values and when queried we get result set in plsql table type.
Both the canvas are identical and value from result set of one canvas get populate on the other canvas.(same lov selected values)
can anybody tell how to clear the second canvas without exiting from the canvas so that if i want to select new lov i can be able to do that?
what trigger can i use to clear only the values of the lov on the sceond canvas and not the whole form(like we use clear_form).
Thanks,
Mandar.

canvas is not something which holds data. canvas holds items. you can either clear item or clear block or clear whole form to clear the data, but saying something like clear canvas is different. one canvas can hold data of 2-3 (or may be more) different blocks. you need to specifically check which item/block you want to clear and then clear it, either using clear_block or clear_item or may be manually assigning NULL value to each individual item. but there is nothing called clear_canvas.

Feature Request: I want Firefox 4 to remember search history, but not form data, without having to use a third-party plug-in. Is this possible now and I am just not seeing it?

I don't like having Firefox (or any browser for that matter) remembering any form history, as I do not see this as secure data storage (IT security/network engineer). Currently the only way to disable this is to also disable search history, which is a useful tool to have, and I am not worried about the security of that data (I don't search for sensitive data). I would like to see these two options under the Privacy->Custom Settings Preference to be separated so that people can more finely control what of their data is stored.
Is this possible without the use of third-party plugins?

Wow. Okay...
I'll let the real veterans in this forum tackle your issues one after the other. But, I can tell you, all will be well.
My only comment would be re: your computer specs:
BJReis wrote:
. This may be due to somewhat older equipment:
GHz Intel Core Duo MacBook Pro with a 4GB memory computer with Ddr3 running OSX 10.8.4
To be completely honest, FCPX is a RAM hog. It just is. But, RAM is relatively cheap, and the pay-off is good.
4GB is right on the edge, IMHO. 16G is ideal.
I wish you luck, hang in there, and standby for more help.

Delivery note form with Adobe

Hi Adobe's,
I'm changing my version 4.6C to ECC6.0, in this version the forms will be in adobe.
I don't find the delivery note in SFP transaction code and the program name for does it with Adobe.
Can you help me??? Or isn't it possible to do with Adobe??
Best regards,
Ana

Hi,
There is no template available of delivery note in Adobe Forms .
Best regards

Filling in PDFs that are not forms?

I have a form I need to fill in. Rather than do it by hand, I'd prefer to use my computer. Unfortunately, the PDF has not been designed with form fields. Is there anyway I can still fill it in using either Acrobat Pro or some other Mac OS X application?
Thanks,
Kelly

In Acrobat Pro you can add form fields and fill the fields. Or you can use the typewriter tool.

CT5760 HA Pair not Forming?

Similar Messages

Maybe you are looking for