Ctios failover. how much time spent to to recover the ctios agent

on cce 7.5.x
using /load 0 to put agent on not ready after ctios failover. how much time is needed for agent to do a ready request?.
or using /load 1 (i think is the default behavior) this cause to log out agent. soo How much time must left to do a log in again.
any ideas?

This is what SRND Guide of 7.5 says
When the active CTI Manager Service or PG software fails, the PG JTAPI Gateway/PIM detects an OUT_OF_SERVICE event and induces a failover to the redundant (duplex) PG. Because the redundant PG is logged into the backup Unified CM subscriber CTI Manager Service already, it registers the IP phones and configured dialed numbers or CTI route points automatically. This initialization service takes place at a rate of about 5 devices per second. The agent desktops show them as being logged out or not ready, and a message displays stating that their routing client or peripheral (Unified CM) has gone off-line. (This warning can be turned on or off, depending on the administrator's preference.) All agents and supervisors lose their desktop third-party call control functionality until the failure recovery is complete. The agents and supervisors can recognize this event because call control action buttons on the desktop will gray out, and they will not be able to do anything with the desktop. Any existing calls should remain active without any impact to the caller.
Regards

Similar Messages

How to view how much time is remaing to fetch the result

Hi,
could you please help me how do I view that How much time is remaining to get the final output of my query. one of my query is running from last 7 hours just wanted to now how much time it will take to give final result. is there any way to see it ?
Thanks in Advance.

In general, no.
You can try looking at v$session_longops using your session_id to see if something shows up there.
Certain long operations will have an entry in that view with an estimate of the completion time.

How much time will i take for the battery to drain, with white screen of death?

Yesterday I updated the software of my iPod touch (4gen), and today while using facebook I got the white screen of death. I tried to holding the sleep and home buttons but I didn't help. Then I tried to connect to iTunes but iTunes does not recognize my iPod. It seems that the only solution is to let the battery drain. My question is how much time will it take for the battery to drain (I charged it yesterday). Am I damaging my iPod in anyway?( I am worried because the back is a little hot). Should Ii try co cool it by placing it in front of a fan?

Yes it will show the low battery picture. Then I just connected it to my PC and restored it.
For the cold pack I used one of these gel-packs http://www.coldchaintech.com/products/gel-packs.php ( I had them at home).
I don't think using ice is a good idea here is why:
1. If you use an ice pack you should be careful to prevent water from entering your iPod.
2. Your iPod should not get colder than 32° F which is the minimum Operating temperature. And ice is colder than 32° F.

HT1569 how much time i need to update the iOS 7.0.6

how much time i need to update software iOS 7.0.6

Depends on your connection. Mine took very little time at all.

I need help getting my ipod to show me how much time left on a song !

How can i get my ipod to show me how much time left on a song @ the top under the song that's playing it went away and i dnt know how to put it bck please help me out . . .

No, tap the screen briefly. If you hold your finger on the Now Playing screen - even for one second - the scrubber bar (with the time on it) will not appear.
Tap - the quickest touch you can do.

How much time on Internet is 3G?

I'm thinking of getting an iPad with 3G to 5G for the Internet. Does anyone here have a ballpark idea of how much time one can spend on the Internet per day if they have...say...3G or 5G? (I spend lots of hours a day on the Internet.) Also, is Verizon or AT&T better (consistent up-time, etc)?

Think of it like walking. 3G is like walking at 3 mph, 4G is like walking at 4 mph. This isn't saying how much you can carry, just how fast. Yes, in 10 hours walking at 4 mph you can make more tripsand end up moving more stuff than at 3 mph, but in the end you pay for how much you transport, not how fast you transport it. This is referred to how much data you use and the "G" plans are referred to as data plans. When we got an iPhone with AT&T we had the option of the base package with 0.2 GB data/month, the 2 GB package, and the unlimited. We got the 2 GB package and never come close to it. If we downloaded movies we'd exceed it with 4 movies easily.
Yes, it allows Internet access when you don't have wireless. However, the access may be limited to some items. Netflix would gobble up data. I don't know if you could even use it over a data plan. They restrict some of that heavy duty use to proper wi-fi. For example, you cannot Facetime with 3G, you have to do that with standard wi-fi. Data plans are a convenience but not a true replacement for WiFi. (In case somebody reads this, I am not going to go into hotspot use right now.)
There's also cost considerations. I haven't calculated it but I bet if I started downloading at the maximum rate for which we pay I could probably download over 100 GB per month. We pay $14 for our Internet service with 100 GB potential. We pay $20 (I think) for the 2 GB data plan with AT&T.

Is there a way of checking how much time has been spent on an Adobe document?

I would like to know how much time is spent preparing or completing Adobe forms for time keeping purposes. Is there any record of this in the individual document metadata, or anywhere?

Hi mikeq,
I don't believe that's something that gets tracked in your Acrobat.com online account. There are free time-tracking utilities, though. I did a quick Google search and found a number of them.
Best,
Sara

Is there a plug-in that tracks how much time you've spent in specific files?

I want an easy way to track how much time I've spent on certain projects. I really just need a plug-in that tracks how long files have been open. I'm having trouble searching for one like that; does anyone know if this exists as a plug-in or even as a function of Photoshop (or Illustrator)? This would be very helpful for freelancers. Thanks.

Found this link via Google. I have CS6 and it looks like this, don't know about CC.
How to Keep a Log of Your Work in Photoshop - Digital Photography School

How much time does an AP take to failover to secondary controller

hi All,
My query is to understand how much time will an AP take to failover to its secondary WLC(Backup) incase primary goes offline.
Whats the heartbeat time for each AP to verify reachability to WLC.
also what is the purpose of AP Fail over priority under each AP. i want to ensure AP's fall back to primary WLC once its back online.(Preemption)

Hi Matehw,
My query is to understand how much time will an AP take to failover to its secondary WLC(Backup) incase primary goes offline.
We can not tell exact time but normally It takes 1-3 minutes.
Whats the heartbeat time for each AP to verify reachability to WLC.
AP Heartbeat Timeout - AP sends heartbeat to WLC (By default its 30s). Once the primary WLC(or where AP is connected to)goes down, With heartbeats, the AP realizes sooner that the controller has become unreachable.
also what is the purpose of AP Fail over priority under each AP.
First of all there are three types: it goes like this Cirtical...high...medium..low.
***To configure AP failover priority, we must enable AP Fallback feature globally and then individual APs with a suitable priority level.
*** When using both the local and global backup configurations, the locally configured settings take precedence in the event of a controller failure. If an AP is not able to join any of the locally configured controllers, it then tries to join the global backup controllers.
More info:
http://rscciew.wordpress.com/2014/01/22/ap-failover/
Regards
Dont forget to rate helpful posts

How much time do you spent in Vocals Recording and Mixing?

I would like to know, how much time do you spent in Vocals Recording and Mixing?
I mean, you do doubles and then the are not that correct you record it again and maybe a third version and then you mix it, you cut and arrange some phrases and words so that it is in sync .....
How much time do you spent in this process until you say: This is enough! Because, somehow. you can always do more and try harder and do it again and try this ....
Thanks to all your comments
Martin

Jim Frazier wrote:
If it's taking a singer longer than that, they are not prepared, or it's just not their day
or theyre just so completely horrible to start with and have no business singing in the first place, hahahaha.
sorry jim, i couldnt help it:-)
the better paying and the higher profile the gig, theres really a gamut of singers youll encounter. theres a very well known pop artist i work with that honestly doesnt even get CLOSE to usable vocs until theyve been in there warming up for around 6hrs (takes them this long to get the four other very loud overtones in their voice down to about ONE very loud overtone), and you take takes on them just because you never know. (seriously, 6hrs) but you do it because it pays really well, whats a day of time when you get it back a few times over?? (btw, with this person, theres usually about 20-25 takes to go through when comping a voc, so make that TWO days:-( )
that would be my biggest gauge of how long i spend honestly, the money, unless i have a personal investment in it myself. youll know pretty quickly if youre in trouble or not with a singer. if theyre bad (pitch or timing) but paying well, i will rely on my skills in melodyne to save the day:-) i know what i can do in it and can hear what the singer can or cant do with their voice. sad thing is, the best singers usually arent the ones with record deals.
i know the money gauge prob sounds cold, but for the most part thats the deciding factor. of course there are times you come across real talent and take the experience of working and creating with them over the money, but MOST of the time in this 'business' we dont always have that luxury. plus if youre just starting out, i would take just about ANY gig just to be able to do it and gain the experience, you dont want a really important gig being your maiden voyage in melodyne:-)
i would also go with jims recommendation in melodyne. MD studio lets you use key commands to work (plugin doesnt) and its actually sounds better than the plug itself.
as far as mixing, i cant answer that, i usually dont mix. i will if im the last resort. i would be really discouraged if i couldnt get the mix in a day, with a relisten and tweaks the next day for a couple hours. i sort of mix as i go along just so i can hear everything in its place.
my 2 cents is done with now:-)

How do I display time remaining in a captivate published video so the learning can know how much time is remaining in a video

After I publish my video it just plays but there is no indication of how much time is remaining on the video while watching. How do I display this

It is possible, but you have to know 'time' is bit different, depending if you are talking about the 'editors' time or the real time spent by the the trainee. Have a look at this old blog post, that tries to explain:
http://blog.lilybiri.com/display-time-information
Time can show on the TOC (editors time), and if you have a playbar with a progress bar that gives some indication as well, but both for pure linear projects.

While running the query how much time it will taken, I want to see the time

Hi Folks
I would like to know ... While running the query how much time it will be taken, I want to see the time? in WEBI XI R2.....
Plz let me know the answer.......

Hi Ravi,
The time a report runs is estimated based on the last time it was run. So you need to run the report once before you can see how long it will take. Also it depends on several factors... the database server could cache some queries so running it a second time immediately after the first time could be quicker. And there is the chance of changing filters to bring back different sets of data.
You could also schedule a report and then check the scheduled instance's status properties and view how long a report actually ran.
Good luck

HT4623 I found an update ios6 in my iphone settings and then I tapped on install ,but it is going on and nothing is displaying .Only apple logo is displaying frequently.It has been happening for 13 hours.my question is how much time it will take to upd

Can anybody help in my concern below
I found an update ios6 in my iphone settings and then I tapped on install ,but it is going on and nothing is displaying .Only apple logo is displaying frequently.It has been happening for 13 hours.my question is how much time it will take to update ios

Read this: iOS 4: Updating your device to iOS 5 or later
... oh I think it is a 3gs or a 3
This makes a difference. What does it say in Settings > General > About?

Is there a way to see how much time's left to render?

I was wonder if Final cut pro x have the ability to show how much time is remaining in the rendering process...like premiere or final cut 7 use to, if I remember correctly...Same thing with Compressor 4.1.3

The big problem with estimating time remaining is the app cannot see into the future on the timeline. there might be a very complicated section coming up that requires rendering effects, graphics, or complicated Motion files but only after lots of heavy duty decompression or transcoding.
After using FCP for many years we sort of got a feeling for how much horsepower and time were going to sucked up with any given project or settings but today's monster CPUs and graphics cards have required me to rethink all of that previous experience.

Possible to check how much time an update statement on a table would take ?

Hello @all
I have a table with a fragmented Index, the table has an actula "user_updates" from 226'699.
How can i find out how much time an update on this table takes ?
i would like to check if there is any performance increase when i regroup the index (rebuild), cause the index has a fragementation of 85% now... (or should i delete the index completely) cause there are no user_seeks... only user_updates on the table...
and i thought that indexes only makes sense if users are reading from the table... am i wrong ? (cause on every update from the table, the index (indexes) have to be updated too...
Thanks and Regards
Dominic

Rebuilding the index will not likely result in a modification be quicker. At least not more than marginal. In fact, it might wven be slower, since if you currently have space on the index page for the new row and then rebuild so you *don't* have space then
the index rebuild will make that update be slower (at least for the cases where you get page splits).
However if the index isn't used to find rows (any of the other three columns), then you have an index which only cost you and doesn't help you!
Tibor Karaszi, SQL Server MVP |
web | blog
Tibor, check out this forum thread:
http://social.technet.microsoft.com/Forums/sqlserver/en-US/64ad4f52-2fd8-4266-b4a4-5657c8870246/needed-more-answerers?forum=sqlgetstarted
Ed Price, Power BI & SQL Server Customer Program Manager (Blog,
Small Basic,
Wiki Ninjas,
Wiki)
Answer an interesting question?
Create a wiki article about it!

Ctios failover. how much time spent to to recover the ctios agent

Similar Messages

Maybe you are looking for