Ctrl + Spacebar will not bring up code hints either

I'm using Windows XP CS3 with Dreamweaver from Creative Suite CS4. I cannot get code hints (when enabled) or when I press Ctrl + Spacebar.
When I press Ctrl + Spacebar nothing happens.

Take a look at:
http://help.adobe.com/en_US/Dreamweaver/10.0_Using/WSc78c5058ca073340dcda9110b1f693f21-7bd 7a.html
check near the bottom: Code hinting and syntax errors
Hope this helps :-)
Nadia
Adobe® Community Expert : Dreamweaver
Unique CSS Templates |Tutorials |SEO Articles
http://www.DreamweaverResources.com
Book: Ultimate CSS Reference
http://www.sitepoint.com/launch/005dfd4/3/133
http://twitter.com/nadiap

Similar Messages

Printer will not work: error code 0xc19a0022

Printer will not work: error code 0xc19a0022

Hello citizenED,
Welcome to the HP Forums.
I see that you are getting the error code " 0xc19a0022 " .
I do have a few steps that we can try.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I have also located a document that deals with a 'Problem with Printhead,' 'Printer Failure,' 'Ink System Failure,' or a '0x...' or a 'C2...' Error ...
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

I am trying to update my software and it will not recognize my code, why?

I am trying to update my software on my new Macbook pro and it will not recongize my code, why not? I was sent the confirmation email with the code as well

I am having the same problem. I can not download my update whatsoever. I emailed the support e-mail attatched in the original email, but have not recieved any news.

When I try to log into the app store to update apps or buy apps the user name that appears is an old one and it will not bring up the current user name/ email how do I stop that so that my current email show up ??

When I try to log into the app store to update apps or buy apps the user name that appears is an old one and it will not bring up the current user name/ email how do I stop that so that my current email show up ??

Settings>Store: Tap the AppleID and choose "Sign Out", it will then prompt you to sign in and you can use the new AppleID.
NOTE: Apps must be updated with the AppleID they were purchased under.
EE

DMVPN will not bring up dynamic tunnel unless using static routes

I have a hub and two spokes and each spoke is bringing up a tunnel to the hub and is routing normally. My problem is that if I try to route from spoke1 (10.30.1.1) to spoke2 (10.30.3.1) it will not bring up a new tunnel but instead will route through the hub.
If I put 'ip route 10.30.3.0 255.255.255.0 tunnel 0' on spoke1, it will then bring up the tunnel to spoke2. I know this is an EIGRP issue (my misconfiguration somewhere), can someone look at the configs and point me in the right direction?
Thanks!!!

Use the Debug commands that run on the hub router confirm that the correct parameters are matched for the spoke and VPN Client connections. Run these debug commands.
debug crypto isakmp-Displays messages about IKE events.
debug crypto ipsec-Displays information about IPsec events.
Here is the configuration guide with the Hub & Spoke example. http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801eafcb.shtml

HT1918 My account is asking me for my security code on my credit card, but it will not accept the code as valid? Not sure what to do?

I am trying to purchase an app on a new iPad we have purchased. I'm asked to put in my security code on my credit card for security reasons, but it will not accept my code as valid. Not sure how to proceed.

Is the address on your iTunes account exactly the same (format and spacing etc) as on your credit card bill : http://support.apple.com/kb/TS1646 ? If it is then you could try what it says at the bottom of that page :
If the issue persists, contact your credit card company and verify that they and any company they use to process credit card authorisations have the correct information on file.
And/or try contacting iTunes support : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

Itunes will not accept security code although I have checked with bank ant everything is OK!!!k

itunes will not accept security code although I have checked with bank ant everything is OK!!!k

Carlos...
Try this support article > iTunes Store: My credit card's security code or zip code does not match my bank's records

Will not bring up pictures, maps on google & map quest

Safari 4.02 will not bring up pictures & parts of web pages. Won't do it on Foxfire also. do I have so setting set incorrectly?

Go to Safari Preferences/Security: do you have all four boxes for Java and Javascript enabled?
Also, in Safari Preferences/Appearance, have you checked the box 'Display images when the page opens'?

Will not bring favorites over from IE8

I dloaded firefox to Windows 7 but it will not bring the favorites over. I clicked on "import" and it said it did it but they are no where to be found. Thats problem #1
Problem #2, The reason I have Windows 7 is because my xp computer crashed. On that computer I had Firefox and a big favorite list. I need this list, I want to open that list in Firefox but as you can see from problem #1 I cannot do it because I cannot find it. So #2 Question is "What is the name of the folder which held all of the favorites information" and how can I access it.
I miss Firefox and don't like IE in any form but these "Favorites" problems are keeping me using IE8, Please Help!!!!!

I'd like to hear from the "Awesome" support group that Firefox exclaims about on the support welcome screen. I asked the above question 3 weeks ago and as anyone can see there is no " Awesome" answer even though there are 3 other people with this problem. My opinion is that there is no such thing as a software program that works except for MacIntosh. I have zero problems with 'Safari' and zero problems with anything else that is on my Mac. I'll wait a few more days and if I don't get an answer on this I'm just going to purge Firefox from my system and look for something else. Unfortunately I have wasted too much time on half-butt programs such as this one where simple things must get needless research by the user to just do what it's supposed to do in the first place.

C2921 router will not bring up fibre SFP

c2921 router will not bring up fibre SFP
I can't get two cisco 2921 routers to talk to each other
the setup works find in my testbed with a rj45 cross over cable between them or even with a WANEM cloud emulator(free tool).
after migrating from CU to fibre they won't to talk to each other anymore. worse, both refuse to bring up their wan side fibre SFP.
the "media-type" sub i/f command was used to change to SFP from RJ45
after that, the EN SFP light appears on both routers, but no link light
sh int gi 0/1
GigabitEthernet0/1 is down, line protocol is down
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is SX
the two routers are in different buildings and must pass through a middle building(#2)
B1 - 200m -- B2 -- 900m -- b3
R1 (in building 1) is 200m from building 2
R2 (in building 3) is 900M from building 2
R1 has a MM SFP in Gi 0/1
R2 has a SM SFP in Gi 0/1 as the distance is too far for MM
in building two we have used both a SM to MM media converter
and a layer two switch with SM and MM SFP,
both show similar results
R1(MM sfp) --MM cable-- (MM sfp) switch (SM sfp) --SM cable--(SM sfp)R2
on the switch( in Bld 2), we see links lights coming out of the two routers, for both SM and MM links, this is good and expected. no traffic is seen though
on either router, no link light is seen and both interfaces are down down. shut, no shut, does not bring them up
we have tried different SFP and cables, still no change
one google search mentions an undocumented ciso command to ignore incompatibale SFP, but that does not work in IOS 15
if we add a 3750 switch to the routers Gi 0/1 WAN side as a media converter, we get success.
each switch has two sfp, one Cu and the other MM or SM fibre .
the router "media-type" sub i/f command was used to change to RJ45 from SFP, after that, the SFP EN lights goes out(as expected) on both routers,
R1(CU)-(CU)3750(MM sfp) --MMcable-- (MM sfp) switch (SM sfp) --SMcable--(SM sfp)-(SM sfp)3750(CU)R2
why does this work and the connection on the rtr does not
sh int gi 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is RJ45
this test is not practical in the deployed field and far too expensive
i am looking for a solution and want to know why the SFPs do not work in the routers
i tried two different MM SFP. neither one worked, though from SH INV, one can't tell them apart. on the CISCO site only this one is supported
glc-sx-mm, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch (;
================
%added SFP-GE-s SFP, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch
sh inv
NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9      , VID: V03 , SN: xxxxSFP-GE-s
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: FTLF8519P2BNL-C6B , VID: B , SN: xxxx
%============
%remove SFP and added glc-sx-mm SFP, this is the supported MM SFPO for the 29xx rtr
sh inv
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: SFBR-5766PZ-CS1   , VID:    , SN: xxx
============
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID xxx
9 FastEthernet interfaces
3 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
500472K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2921/K9          xxx
Technology Package License Information for Module:'c2900'
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
uc            None          None          None
data          None          None          None
Configuration register is 0x2102

Problem solved.
MAJOR untested bug in IOS 15.0(1)M3 which was the default image when we bought the devices
*** AVOID IOS 15.0 series ***
there are several bugs related to SFPs like:
does does recognize SFP
des not recognize some EHWIC cards such as, but not limited to EHWIC 1GE-SFP-CU
CSCtj35792
c3900 : gigE SFP should switch to 1000/FD if other side has no nego
Externally found severe (Sev2) bug: M-More
CSCth28824
c3945 GE shows DOWN/DOWN as compare to SFP
Externally found moderate (Sev3) bug: R-Resolved
They were fixed in 15.0(1)M4 or later
You can check the caveats for this IOS Release 15.0M:
http://www.cisco.com/en/US/docs/ios/15_0/release/notes/150MCAVS.html

My ITunes will not work error code 2503

window XP cannot uninstall ITunes. ITunes will not operate. error code 2503

Hello, bearbassman.
Thank you for visiting Apple Support Communities.
Here are the steps I would recommend going through when receiving this error.
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
Jason H.

My Iphone 4s will not bring up the keyboard to type in the password for updating my apps, how do I fix this?

My Iphone 4s will not bring up the keyboard to type in the password for updating my apps, how do I fix this?

Try a Reset... you will not lose data or settings...
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430

Trying to install cs6 on new make but will not take activation code, i think it is because i didnt deactive on old comp

trying to install cs6 on new make but will not take activation code,

how do I fix the issue

I am getting an error "The older version of Bonjour cannot be removed" I am trying to get rid of all of my Apple Software. What can I do? Because it will not let me uninstall iTunes either.

I am getting an error "The older version of Bonjour cannot be removed" I am trying to get rid of all of my Apple Software. What can I do? Because it will not let me uninstall iTunes either.

Akeenleyside,
Are you removing your Apple software in an attempt to update to iTunes 10.5? I ask this because I am getting the same message when trying to install iTunes 10.5.

My MacBookAir will not come on. I either get a picture of a folder with a ? or a get a globe. What do I do? it's 7 months old

My MacBookAir will not come on. I either get a picture of a folder with a ? or a get a globe. What do I do? it's only 7 months old

A flashing question mark or globe appears when you start your Mac

Ctrl + Spacebar will not bring up code hints either

Similar Messages

Maybe you are looking for