CTS (MACsec) and WS-X6716-10GE (With DFC4)

Hi, I am not able to activate MACsec (CTS manual) on the WS-X6716-10GE module. I have a VSS with VS-SUP2T-10G installed. I am able to activate MACsec (CTS manual) on the WS-X6908-10G module.
Is MACsec supported on the WS-X6716-10GE (DFC4) ????

Magnus
The WS-X6716-10G is CTS aware but not CTS capable which means it can understand the tags for forwarding decisions but not add tags.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/15-1SY/config_guide/sup2T/15_1_sy_swcg_2T/trustsec.html
Jon

Similar Messages

WS-X6716-10GE with WS-F6K-DFC4-E

I have a C6509 with VS-SUP2T-10G and WS-X6716-10GE with WS-F6K-DFC4-E installed. How many ports do i lose when enabling performance mode. With SUP720 and WS-X6716-10GE (DFC3) I will lose 12 ports. Should be 8 ports but I don't see any documentation on it.

How many ports do i lose when enabling performance mode.
Sup2T means the chassis will have a back-plane speed of 80 Gbps. So this means that if "performance mode" is enabled then you loose half of the ports (or 8-ports).

Compatibility WS-X6716-10GE and CVR-X2-SFP10G module

Hello,
I need help to determine if the modules WS-X6716-10GE and CVR-X2-SFP10G, I refer to the matrix compatibility and there isn´t any informtation about this module specifically.
Thanks for the help.

It is supported. Have a look at table 6 in the same link
VS-S720-10G-3C
VS-S720-10G-3CXL
WS-X6708-10G-3C
WS-X6708-10G-3CXL
WS-X6716-10G-3C
WS-X6716-10G-3CXL
(With CVR-X2-SFP10G converter for X2 ports)
HTH

WS-X6716-10GE line card with WS-F6700-DFC3C

HI,
1) Currently we have WS-X6716-10GE line card with WS-F6700-DFC3C, do we have DFC upgrade option for this to make it supported by Sup 2T-XL
Regards,
Praksah

Hello,
Indeed, you will need WS-F6k-DFC4-EXL. WS-X6716-10G will be supported with SUP2T with that DFC upgrade.
Please refer
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/15.1SY/release_notes.html
Haihua

CTS Based Simple Bike Speedometer - Problem with CTS Pulse

Everytime a magnet rotates, a sensor sends a CTS signal...I know the hardware works, as it works with another Speedometer writen with Delphi (Spinner on SourceForge). However, my program is getting the right speed, then numbers way too big for about three pulses, the right speed, garbage again, etc.... I'm assuming there is something about the CTS protocol and how the Java program needs to respond to a CTS event that I'm not getting. Or could it be my use of systemtime?
Here's code snippets.....
Oh, and I'm using DSR for cadence, and RI for heartrate, any similar issues that I need to be aware of using them?
Thanks
     serialPort = (SerialPort)portID.open("IntervalTrack", 0);
        serialPort.setSerialPortParams(9600,
                SerialPort.DATABITS_8,
                SerialPort.STOPBITS_1,
                SerialPort.PARITY_NONE);
        serialPort.addEventListener(this);
        serialPort.notifyOnDSR(true);
        serialPort.notifyOnCTS(true);
        serialPort.notifyOnCarrierDetect(true);
        serialPort.notifyOnRingIndicator(true);
        serialPort.notifyOnDataAvailable(true);
        serialPort.setDTR(false);
        serialPort.setRTS(true);--- snip ----
    public void serialEvent(SerialPortEvent e) {
            System.out.println(e.getEventType());
            switch (e.getEventType())
                case SerialPortEvent.CTS:
                    doCTS();
                    break;
                case SerialPortEvent.DSR:
                    doDSR();
                    break;
                case SerialPortEvent.RI:
                    doRI();
                    break;
    private void doCTS(){
        double dblSpeedT2 = System.currentTimeMillis();
        double dblDeltaSpeedTime = dblSpeedT2 - this.dblSpeedT1;
       //todo resolve divide by zero if (dblDeltaSpeedTime == 0.0)
        //                  dblDeltaSpeedTime = 1;
        this.dblSpeedKmPerHour = 3.6 * this.getWheelSizeInMM() /
                      dblDeltaSpeedTime;
        this.dblSpeedT1 = dblSpeedT2;
    }

Just for future reference if someone googles this unanswered question (so much for Java forums help.....).
The problem was that I needed to distinguish between the evt. changing from true to false and only computing for one or the other. So if it was false I computed, if it was true I continued. (err....or was it the other way around?) either way, thats the fix.....not sure on the why of this though..

Ntp settings for CTS 1000 and CTS 3000

I installed a CTS 1000 and a CTS 3000.
They both use CUCM.
Now my problem is: When i capture a logfile from a CTS the date and time on the files in the captured logfile are not correct. i.e. x/x/2006.
When i go into the admin page of the CTS and go to the ntp settings it sais it can only be changed in the CUCM.
the phones connected to the CTS have the correct time.
What do i have to do to fix this?

1. Login to CUCM
2. Add NTP servers IP addresses under "System>Phone NTP Reference"
3. Go under "System>Date/Time Group" and add "Phone NTP References" you created
4. Restart all CTSs devices
CUCM should push device's config to TFTP server and upon Restart, CTS should download new config with NTP references. Login to CTS web administration and verify NTP server list under "System Settings".

Cisco Network Assistant 5.5 and WS-X4013+10GE

I have installed CNA 5.5 and it works fine with most of the devices, including catalyst 4500 series with different supervisors (WS-X4013+, WS-X4013+TS, WS-X45 SUP6-E).
It can also detect supervisor WS-X4013+10GE, but CNA failed to show this device in Front Panel View. Is there anything I have to do to make the devices with Supervisor WS-X4013+10GE to be shown in Front Panel View?
WS-X4013+10GE are in either 4503 or 4506 chassis, running IOS version 12.2(31)SGA or 12.2(40)SG.
Please give some hints, thanks.
Rgds,
Sunny

I downloaded Cisco Network Assistant 5.5, everytime when I try to run
I get error message "Could not creat Java virtual Machine' any idea how
to solve this?
To overcome this problem, open the file C:\Program Files\Cisco Systems\CiscoSMB\Cisco Network Assistant\startup\startup.properties (the default installation path), and modify this entry:
JVM_MAXIMUM_HEAP=1024m
Replace 1024m with a lower setting that does not exceed the available RAM. There is no way to foresee what value will work. Try 512m, and lower it further if necessary. You can use the dial peer tag range 2500 to 2999 out-of-band to define your own dial peers.
Check out the below link for more information
http://www.cisco.com/en/US/docs/net_mgmt/cisco_network_assistant/version5_0/release/notes/OL12210a.html
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

SharePoint Foundation 2013 - Multi-tenant Install and OneDrive for Business with Yammer i

Hello,
After installing SP Foundation 2013 (SP1) with Partitioned service applications we have noticed that while clicking on the "yammer and oneDrive" link the below error message comes up:
_admin/yammerconfiguration.aspx
any ideas??
http://technet.microsoft.com/en-us/library/dn659286%28v=office.15%29.aspx
we have also noticed that MS mentioned "OneDrive for Business with Yammer integration doesn’t work for multi-tenancy or partitioned service applications for on-premises deployments"
ja

ULS
Application error when access /_admin/cloudconfiguration.aspx, Error=Object reference not set to an instance of an object.   at Microsoft.SharePoint.WebControls.SPPinnedSiteTile.OnInit(EventArgs e)     at System.Web.UI.Control.InitRecursive(Control
namingContainer)     at System.Web.UI.Control.InitRecursive(Control namingContainer)     at System.Web.UI.Control.InitRecursive(Control namingContainer)     at System.Web.UI.Control.InitRecursive(Control
namingContainer)     at System.Web.UI.Control.InitRecursive(Control namingContainer)     at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
=====
To me it seems SharePoint social networking features require the full SharePoint Server product AND are not available with the free SharePoint Foundation, If correct then why MS punching it here in Foundation without a friendly error message..
ja

Open and close multisim contact with LabVIEW

Can I open and close multisim contact with labview and read the receptor estatus (p.e. lamp)?
Thanks.
Attachments:
Dibujo.JPG ‏13 KB

Hi Guddan,
I created a RFC having a query which is taking a long time to execute. So i want to close RFC connection with portals which is via java connector(JCO) before that query and open the connction again after that query.
I guess i will need to understand your requirement a little more in detail, as i understand you have an RFC which has a query within to fetch some data and is taking a long time to do so. In the meantime you don't want to keep the connection open?
My question would be, Is the role of this RFC to only execute the query and fetch the data or does it do something else?
If it does other things and these are independent of the query execution, then you can span a parallel call within the RFC to execute the query and in the meantime the RFC does the other things (or vice versa) hence reducing the overall time taken.
If the sole purpose of this RFC is to execute the query, then you will not be able(i mean to say there is no simple and direct way of doing this) to close the connection after the Query is started and re-establish the connection after its execution, for a simple reason that - how will you know if the query has completed it's execution, so that you can establish the connection back.
Alternate solutions, make this a two way asynchronous call, 1) You invoke the RFC asynchronously and close the connection, the RFC in turn will execute the query and transfer the data to JCO via another RFC call.
If this needs to be a synchronous call, then you will need to optimize the query to its best.
Regards,
Chen

I have recently purchased MacBook Pro with Mac OSX 10.7.3 Lion and I would like to install Final Cut Pro 6 Studio2, and it came up with this error: 'you can't open application FinalCutProStudio.mpkg because PowerPc apps are no longer supported..pls advise

I have recently purchased MacBook Pro with Mac OSX 10.7.3 Lion and I would like to install Final Cut Pro 6 Studio2, and it came up with this error: 'you can't open application FinalCutProStudio.mpkg because PowerPc apps are no longer supported......Is there a way to run FCP6 on lion withoput this error? Any help would be appreciated.....

Hi Shane,
Just one more quesiton re: this topic, I am looking to get rosetta but do not have Leopard or Snow Leopard...
I read that it is not on Snow Leopard only on Leopard....so do I need to get only Leopard? Can u advise?
Alternatively I do have Mac OS X Tiger so is it on this and can I install it from here?
Please excuse my lack of knowledge here, just trying to get my FCP 6 up and running asap....
Best Rgds.

How do I change my Ipad to access Itunes store in a different country than the one I usually use and have my account with?

I usually use the Itunes application on my Ipad in FRence and use the French Itunes store. I am now in Cyprus and after synchronising my Ipad there I now can access the US Itunes Store but my purchases are refused as my account is with the French Itunes store. How do I either open an account with the US Itunes store or revert to the French Itunes store on my Ipad?

synchronising is not the problem i think, you need a new US apple id. i only have a malaysian credit card but i have separate ids for US UK and Malaysia. i have travelled to these 3 countries and have home adresses in each country but for buying stuff, I use an iTunes store card instead of a credit card cos its easier. you do not need a credit card that must have billing address from the same country as the iTunes store. So I would suggest if you are currently based in the US go the nearest apple store buy an iTunes store card (i buy in multiples of US$100 with a credit card) and use your current US home address as the US iTunes address.
so log off your french iTunes store account, create new US apple id for your iTunes store account using your current US address and then redeem your itunes store card and voila you are set to go. (did i mention you will also need a new separate email address for the new apple id) i have one each from gmail, yahoo and hotmail for each separate id.
the only drawback is that when you want to do an update for the apps that you buy from the different iTunes store, you must log in to that iTunes store account ie if you buy an app from the US store you must log in and update with the US store id and to update the apps from the French store you must log off from the US store and log in again with the french store id.
hope this makes sense to you.

How to configure a shell and tube heat exchanger with Lab VIew to get data

HiI
In our undergraduate chemical engineering labboratory we want to configure our shell and tube heat exchanger with a DAq and Lab VIEW to get information about the temperaure (of the cold fluid stream being heated), the pressure (of the steam on the shell side of the heat exchanger) and the flowrate (of the water being heated).
Can anyone suggest thermocouples, pressure transducers and flowmeters to fit between the heat exchanger and the DAq?
P.S. the heat exchanger is already fitted with thermometers, a pressure gauge and a rotameter but we don't know how to connect these hardware to the DAq
Solved!
Go to Solution.

It sounds like you have enough information to pick out appropriate sensors, you just need to do the research. I would start looking through the Omega catalog, or give them a call - they're usually helpful. I can't take the time to spec out parts for you - that would be a lot of time spent on someone else's project. Most pressure sensors put out either a 4-20mA or 0-5V signal, either of which you can read through an analog input on a DAQ; measuring a 4-20mA signal requires a resistor to convert to voltage. Most of the NI DAQ boards can read a thermocouple on an analog input, but make sure that your hardware does support reading thermocouples. For accurate readings, use a device that has built-in cold junction compensation - for example, the SCB-68 connector block - and for the most accurate readings, get a board specifically designed for temperature measurement.
For the flow measurement, a standard, simple solution is an orifice plate. You put a differential pressure transducer across it, look up the appropriate equations, and use them to calculate the flow rate given the density of the fluid (which you'll be able to calculate from the pressure and temperature, since steam tables are widely available). There are other differential pressure devices available as well - at a previous job we used a V-Cone from McCrometer. If you call them they'll spec one for you - but get an approximate cost first to make sure it's within your budget.

Ipod nano 4gb and ipod video 80g with windows vista

hello! i've been trying (rather unsuccessfully) to sync the ipod nano to my laptop which has windows vista OS. i have the latest itunes 7.2 (just updated today from 7.1) and i always get the "found new hardware" pop-up everytime i plug the ipod nano via usb port. i also did the 5r's, but still the computer cannot and will not detect any software. i even downloaded the softwareupdater28-06-2006.exe but it will not run because it's superseded by itunes 7. my friend has an ipod video 80gb and i tried connecting it too, same thing popped up. both ipods do not show in "my computer" so i cannot even backup my songs! ah well. i just need to get the driver for the ipod i suppose. please help, any suggestions will be greatly appreciated.

i have been having the same problem. My laptop was upgrade to windows vista and worked perfectly fine with my ipod and with others which had previously been used with the computer when it was running XP. My IPOD unfortunately crashed and need to be replaced. I brought it back to the laptop and connected it. it was not recognised but the others still are!
I have been looking on the internet and you are the only other i can find who is suffering this problem. i have looked in device manager and the new ipod is recognised as a 'other device', whereas the ipod that still works is classed as a 'portable device'. i have looked at the drivers and tried to install them by copying the drivers on the original ipod, but have not succeded. Since updating itunes to 7.2 i have been getting a 'do not disconnect' message on the ipod but it still does not appear in the sources list in itunes.
I have tried everything and am about to give up please HELP!
Someone somewhere must know a way around this........ as the London apple store "has never heard of this problem"
Windows Vista Ipod Nano 2G

HT1349 I can not run the scanner in my main user, but only the second user and the same thing with updating apps! Why is this happening???

I can not run the scanner in my main user, but only the second user and the same thing with updating apps! Why is this happening???

Welcome to the Apple Community.
Enter the details of her second account at system preferences> mail, contacts & calendars.

On 3G we cannot send emails from either our iPhones or iPad and this also happens with some WiFi connections but not all. Yet we can always send emails from our Hotmail Email account. What is causing this and what do we need to do to resolve it?

On 3G we cannot send Business emails from either our iPhones or Ipad and this also happens with some WiFi connections but not all. Yet we can always send emails from our Hotmail Account using both 3G and WiFi.
We bought the iPhones and Ipad so that we could send emails while we are out of the Office, but we are not able to do this unless we can find a WiFi connection. Incoming emails are fine. We use IMAP, for Business emails just incase this is relevant and I know that Hotmail is POP3.
Our technical IT knowledge is not great, so we look forward to your suggestions as to how to resolve this.

Contact whomever supports the email account and get the correct Outgoing email server settings from them.

CTS (MACsec) and WS-X6716-10GE (With DFC4)

Similar Messages

Maybe you are looking for