CUCM 10.5 Encrypted control and media

When a CUCM is encrypted;
1) It uses TLS for signaling and can fallback to TCP, correct?
2)for UDP it uses SRTP , correct?
3)any doc showing the encrypted ports uses?
thanks

Correct, TLS fallbacks to TCP in mixed mode.
Voice uses SRTP if the Phone security profile is set for SRTP (Encrypted).
Here is the port list:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/port/10_0_1/CUCM_BK_T537717B_00_tcp-port-usage-guide-100/CUCM_BK_T537717B_00_tcp-port-usage-guide-100_chapter_01.html

Similar Messages

Problem with OS 10.2.0.424 and Media Card Encryption

Several weeks ago I upgraded to OS 10.2.0.424. Everything went fine, no problems. My phone worked perfectly.
Then over one week later I turned my phone on in the morning and after it had booted it said "your media card was encrypted on a different device. You will need to reformat your media card on this device before you can use it".
Now, the following should be noted very carefully: THE MEDIA CARD WAS BOUGHT SPECIFICALLY FOR MY Z10, IT WAS FORMATTED IN THE SAME HANDSET, ENCRYPTED IN THE SAME HANDSET AND HAS ***NEVER*** BEEN OUT OF THE HANDSET.
As far as I am concerned, this is a fault with the upgrade. Having looked on Crackberry.com I see many other users having a similar problem. I am fortunate in that I do weekly backups of my handset including the media card. However I am reluctant to use my media card again in case this problem recurs.
I tried contacting Blackberry help on Twitter however I can only assume that the Blackberry Twitter team are sub-contractors who don't work for BT as their advice was along the lines of "have you tried rebooting? You have? Oh well, you'll need to speak to your mobile provider as there's nothing we can do."
Please, Blackberry, can you acknowledge this fault and advise what your timescale is for resolution?
A dissatisfied loyal Blackberry customer.

If the user removes the media card from the BlackBerry device and places it in a new BlackBerry device, the new BlackBerry device cannot decrypt any files that the first BlackBerry device encrypted on the media card using a randomly generated device key. If the first BlackBerry device encrypted the files on the media card using the BlackBerry device password, when the user removes the media card from the BlackBerry device and places it in a new BlackBerry device, the new BlackBerry device prompts the user for the password used on the first BlackBerry device to access the files on the new device.
The above is from BlackBerry:
I can only assume that Upgrading is like changing Devices, so before Upgrading save all data.
Someone else with more knowledge about encryption and seeing this post may respond.

Media Termination points and media paths with CUCM

Hi all,
I could really use some help regarding this topic. Please allow me to explain the situation.
Ok we have some endpoints that are not Cisco but cisco have developed cop files for CUCM and they are seen as a cisco device and register the same as any other phone. This isn't anything to do with the problem, but I want to make this clear. These are actually dealerboards for trading and register cisco lines the same as any other cisco telephone.
Ok so here is the story;
We have a CUCM cluster in London and a local gateway for local PSTN breakout. There are endpoints that are in Dubai and the register to the CUCM cluster in London. Dubai have their own MGCP gateway for local breakout to PSTN.
Here is the problem;
When a Dubai endpoint makes a call to a PSTN number in dubain there RTP is send from the endpoint, back to the London CUCM, the London CUCM then points the RTP at the gateway in Dubai. This is using a lot of bandwidth and I am not clear on how to change this so the endpoints send media directly to their MGCP gatway.
In my lab I have sent up 2 CUCM's connected by E1 via MGCP gateways, this is to simulate the PSTN network. I can see that on CUCM 7 this is not the case and media is sent directly to the MGCP gateway, on CUCM 8 media is sent via the CUCM to the MGCP gateway. I have since then added in a software MTP on the MGCP gateway for CUCM 8 and now everything hits the gateway as I have specified MTP is required on the phones profile. This was good but even when I make an internal call, everything hits the MTP instead of using IP-IP direct medial.
Please can someone advise what I need to do or if this type of behaviour is expected.
Many thanks,
Joe

Hi,
You can use this link to learn how to collect cum traces..
https://supportforums.cisco.com/document/126666/collecting-cucm-traces-cucm-862-tac-sr
We can help you look at the logs and explain whats going on..
Please include the calling and called number and time of call..Check the traces to ensure that the call is there first before sending it over here.
What type of phones are you using? What dtmf method have you specified in your mgcp configuration

Keyboard,trackpad and media bar inop at different times......

I have a HP Pavilion dv7-1264nr That originally came with Windows Vista basic/home...After a clean installation of WIndows Vista Ultimate, the trackpad (touch mouse) and media control (play, pause, mute, forward/back, stop, volume slider) and wireless on off, and "quickplay" touch buttons are inop...They aren't actual "buttons", they're touch buttons, similar to the trackpad. The keyboard is intermittantly inop, although a USB keyboard and mouse work perfectly, and the trackpad (mousing surface) and buttons are alos inop.
Before I get a lot of messages asking to check the connection ribbon, the NUMLOCK light is illuminated, the trackpad on/off indicator lights (and changes color from "white" to amber) and the media bar, near the display illuminates, and just recently, I got the wireless to connect, and the LED changes from blue to amber, and turns off the wireless network card.
Is there a "package" of drivers for the entire "system" that Microsoft doesn't have, and can't search for on-line, that I can download from HP? I assume HP has a driver for the entire "control panel" that Microsoft may view as separate pieces....
I've also noticed that the webcam in the top of the display is not recognized....Possibly another part of the "package" driver I'm lacking?

Has anyone find a fix for this? I've been using my Dragon Dictate headset on my MacBook Pro for about a year, and then today, when I plugged it in, I got this:
4/16/14 10:01:04.000 AM kernel[0]: USBF:    47.766    The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 1 of Hub at 0x4000000)
4/16/14 10:01:07.000 AM kernel[0]: USBF:    50.269    AppleUSBHubPort::FatalError - Port 1 of Hub at 0x4000000 reported error 0xe00002c7 while doing clearing port power feature
4/16/14 10:01:07.000 AM kernel[0]: USBF:    50.269    The IOUSBFamily was not able to enumerate a device.
Here is what I have tried so far:
Reset the PRAM
Reset SMC
Verify disk (there were no problems)
Repair permissions
Boot with an external USB hard drive (which works fine on the "problem" computer) that contained an old SuperDuper clone of my hard drive from several months ago. I received the same "The IOUSBFamily was not able to enumerate a device" error when I plug in the headset.
Tried to headset on another computer, and it worked fine.
Plug in an external USB keyboard into the problem computer, and it works fine.
All of this would lead me to conclude that it is a hardware problem. But it seems that if it were a hardware problem, the external USB keyboard and external USB hard drive would not work (which they do). If the problem were with the headset, it wouldn't work on another computer, but it does. So I'm wondering if it's some sort of firmware issue…??????? URG!!!!!!

Cisco Phone Control and Presence 8.6.1.1185 with IBM Lotus Notes 8.5.2 (Integrated Sametime Client 8.0.2) - No presence status visible

Hi community,
I am trying to integrate Cisco Unified Presence 8.6.1.10000-34 with IBM Lotus Notes 8.5.2 with the integrated Sametime Client version 8.0.2 via the Cisco Plugins 8.6.1.1185.
Phone control is working fine, whereas the presence status is not shown (= no handset symbol next to the Sametime user). When I look in the preferences of the plugin, I can see that the plugin has connected successfully to the CUCM (8.6.2.20000-2),whereas the connection to the CUPS has not been established.
The user id as well as the password are all the same on all systems. Here is a description of what I have configured via the ciscocfg.exe tool:
Feature Control:
- Enable Phone Status -> checked
- Enable Dial Using Cisco IP Communicator -> unchecked (not required)
- Enable Control Desk Phone -> checked
- Default Mode -> Control Desk Phone
Control Desk Phone Settings:
- Voicemail Pilot Number -> left blank (no voicemail)
- Cisco Unified Communications Manager
     - Servers -> IP address of CUCM
     - Read Only -> unchecked
     - Use as Default CUCM -> checked
     - Synchronize Credentials -> checked
          - Use Sametime Credentials -> checked
Use Secure Connection: -> not required
LDAP Phone Attributes: -> not required
Phone Status Settings:
- Cisco Unified Presence Servers -> IP address of CUPS
- Read Only -> unchecked
- Synchronize Credentials -> checked
     - Use Sametime Credentials -> checked
- Sametime User ID Mapping
     - Use Business Card Attribute -> MailAddress
     - Remove Domain -> checked
- Display Off-Hook Status Only -> unchecked
At the moment I don't see an error in the configuration, but maybe I am wrong. Could anyone please tell me what the error could be?
Thanks a lot in advance!
Kind regards,
Igor

Hi all,
here are some additions to my above post:
Servers and clients used:
1x CUCM 8.6.2.20000-2
1x CUPS 8.6.1.10000-34
1x IBM Lotus Domino Messaging Express Server 8.5.2
1x Sametime Entry Server 8.5.2 (on top of the Domino server)
2x IBM Lotus Notes 8.5.2 with integrated Sametime 8.0.2
2x Cisco Phone Control and Presence with Lotus Sametime (PCAP) 8.6.1.1185
2x Cisco Unified Personal Communicator 8.5.5.19839
Setup:
- CUCM, CUPS and CUPC are working fine, i.e. Desk Phone control via CUPC, as well as availability and presence status are working without issues
- IBM Lotus Domino server is the LDAP Directory, the Sametime Entry Server is installed on top of the Domino server and uses the Domino Directory
- User ID and password on CUCM/CUPS match the ShortName field and password in Domino
- The PCAP plug-in has been manually deployed to both Notes clients with the following configuration:
     - Enable Phone Status -> active
     - Desk Phone Control -> active
     - no credential synchronization for CUCM and CUPS, i.e. every user must fill the user details himself
     - Sametime User ID Mapping is implemented via the LDAP Attribute uid (which is equal to the user id in CUCM)
     - LDAP configuration filled in with details of the Domino server
Phone Control is working fine, also the connection to the LDAP server (Domino) is fine. However, when I type in the credentials for the CUPS server login, I can see (in Troubleshooting pane) that the user (pparker) is connected to the CUPS server for a short period of time and then gets disconnected. After that no connection is possible to the CUPS server, i.e. status is always disconnected.
I have collected the Tomcat (EPASSoap00010.log and security00010.log) logs via RTMT and compared them to the logs from the PCAP plugin. The relevant time period is from 15:14 to 15:17. In the Tomcat logs I can see that the authentication is successful (see attached files), however in the log of PCAP plugin I can see the following messages:
2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
I don't understand why the connection is rejected although the Sametime Internal ID and CUPS User ID match. Does anyone know what the issue could be?
All posts are very much appreciated!
Thanks a lot in advance!
Kind regards,
Igor

"Quality and Media" not displaying in Print dialog.

I am using Mac OS X 10.6 Snow Leopard on a Macbook Pro with a Canon MB5220 Multifunction printer over WiFi. I have installed the Canon Drivers and can print to the printer but the "Quality and Media" menu choice does not display in the print dialog so I can't set any of the quality settings or the color settings for the printer.
I installed and re-installed the drivers. Tried with several applications such as TextEdit and preview. Only menu choices are Layout, Color Matching, Paper Handling, Cover Page, Scheduler.
Is there anything that would keep Quality and Media from dispaying?

It's not just the Quality & Media menu that appears to be missing. There are three other Canon menus you should see like below;
These menu items are supported by the plugins bundle installed in /Library/Printers/Canon/BJPrinter/PDEs, which supports a number of Canon inkjet printers. Since reinstalling the driver for the MG5220 has not helped then I would try a reset of the printing system and then adding the printer again. To reset the printing system, open Print & Fax, move the mouse over the Printers list and Control-click. The reset popup will appear. Select it and authenticate if prompted and then restart the Mac. Please note that this action will remove all printer and scanner queues from Print & Fax, but not the associated drivers so just the queues will need to be added again.
If this action does not resolve the problem then try running the Canon Driver Update v2.6.

Apple remote control and PB 17"

I have my laptop hooked up to my TV. I play quicktime and others video media though it to my TV. The Laptop is far from where i sit so to Fast Forward or pause or anything I have to get up and control it from the Laptop.
Is there a way to get the apple remote control to work with the PB 17" sonce it doesnt have a remote sensor like the new macbook pros do? Or any type of remote control or way to do this?
I want to be able to control the media from about 20 feet away (Lazy I know but in theis day and age... )
Thanks,
Joe

Keyspan makes several remotes:
http://www.amazon.com/Keyspan-URM-17A-Express-Remote-Control/dp/B0006OCZLM
As for Front Row compatibility, I don't think that's there, because it would have to break the license from Mac OS X. Equinux makes a nice software like Front Row called MediaCentral:
http://www.equinux.com/us/products/mediacentral/latest.html

Remote Control and MediaSourc

I hava an Audigy 2 ZS Platinum Pro. I formated my HD last night and reinstalled XP. I then installed the new drivers and Media Source 5 and new DTS Neo plugin. But when I tried to install the old Remote Control plugin, it didn't work, it said I don't have a new Media Source. I couldn't find a new version of the plugin (compatible with media source 5), so, how am I supposed to make remote control work?ThxClaudio Lima[url=mailto:[email protected]">[email protected][/url]?

It is a known issue that the remote does not work in MediaSource 5.
See this thread....
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=85763
You only alternati'ves are to:
. Go back to MediaSource 3.
2. Find alternati've Remote control software solutions that work regardless of the version of MediaSource. There are many alternati'ves if you search these forums.
Hope that helps!

Remote control and MSI PC-DTV Mega Sky 580

Hello,
I bought one of these recently and initially had problems when installed. It would initially run fine but after I closed the program down and restarted it the PC would just reboot.
I was using the front USB ports so I moved it to the rear ports and removed and reinstalled the drivers/software. It runs just fine now and the quality of the picture superb. I've rerun the device over a few days and all seems okay. I appear to have all the available programs from the Sutton Coldfield transmitter although this morning I booted up and the screen was blank. I realised I had last looked at BBC4 and of course thats only a part time channel!
I've looked at the MSI site at the drivers/Presto PVR updates but I am not sure which of the four I should download and use. In fact as the device is working is there any advantage in doing this?
Lastly... I'm not sure if this is a problem or not but the remote control doesn't work. Reading through the forum I'm wondering if I have the wrong end of the stick and the remote only works with Microsofts MCE. I have Microsoft XP SP2. Does the Mega Sky 580 not have a built in IR sensor and am I wasting my time pointing the remote at it and swearing?
Microsoft XP SP2 with current updates.
2x300GB
1GB ram
Intel D820
Onboard graphics and sound
Dust and dog hair arranged attractively around the box!

Hi,
Okay I have the bundled Presto PVR software so the unit must be faulty. I thought that the remote control and bundled Presto PVR would only work if installed on a PC where the operating system was Media Centre Edition.
So the remote control and bundled Presto PVR should work if installed on a PC with Windows XP SP2?
It looks a bit like I'll have to get a different make. I tried to rescan the channels last night because I was missing UKTV History and now I cannot get BBC1,2,3,4 or radios 3,4,6,7. I get loads of duplicates though like 5 Q's 4 ITV3's. All this on the same aerial I was using yesterday.
I even tried it with an indoor/attic aerial that works nicely with my other freeview (set-top style not PC) boxes but no matter what I tried I just get the same duplicated list of a few channels. Even tried it with the indoor/attack aerial upside down, back to front! Same list of 63 channels but most duplicated.
They all work fine but I would prefer a complete set
I

Preserving tape name and media start/end

I shoot lots of tapes of random footage to get short general-purpose clips for use later. Years ago when I started, I would preview in the capture window via device control, carefully set log in/out points, and let batch capture make all my little clips. Then I learned how hard that is on my camera's heads, so I got Scenalizer Live and used a new workflow - I captured my whole tape, and then sliced, trimmed, and renamed the "keeper" clips. But since most of my clips don't need audio and SCLive doesn't know how to make a video-only AVI, most recently I've gone back to using PPro for the slice and rename operation, putting the captured video on the timeline, slicing and dicing, and then "exporting to movie" the good pieces to make new AVIs, with only video and with the filenames I want. (Yes, I know there are purists out there who would be concerned about generational loss of methods 2 and 3, but in DV-AVI I just can't see how any mere mortal could tell the difference.)
But just now I discovered that only my first method preserved the information of where the clip originally came from, i.e. the Tape Name, Media Start, and Media End. All the rest lost that information when I trimmed the clips in either SCLive or PPro. Argh!
These clips are a lost cause, but for the future, is there a better workflow, one that will preserve both the clip information and my tape heads?

I agree - the metadata doesn't need to be repeated for every frame - just once for the clip.
If the clip gets chopped up in PPro (or SCLive or whatever program), it doesn't seem like it should be that hard for the software to just do the math - if I have a two-minute NTSC clip that was originally captured from timecode 12:00:00 to 13:59:29, and I chop it into a 30 sec. clip and a 90 second clip (silly simple example), the resulting two clips should still preserve the Tape Name and other info, and the start/end times should be 12:00:00-12:29:29 and 12:30:00-13:59:29. But instead both PPro and SCLive delete the Tape Name, and the start times of the resaved clips are all zero. Naturally if what is on the timeline when I save is a composite of multiple clips it's a different story, but if the only editing has been to simply put the clip on the timeline and adjust the end points and/or cut with the razor tool, it would be nice if the capture data was preserved.

How to encrypted control communication services on clients in cell Manager.

Hi All,
I am trying to enable the encrypted control communication services on clients in cell Manager.
But it is giving error as -Failed to enable encryption for hosts:
Data Protector version is 6.20

You may want to try the business support forums found below.
http://h30499.www3.hp.com/t5/Data-Protector-Support-and-News/bd-p/itrc-251#.UecCX20SSO4
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Premiere Pro CC 2014 update and Media Encoder update fail to install

Hi -
I've been updating my CC applications. But PP CC 2014 and media Encoder say: "UPDATE FAILED". Naturally I cannot get through to Abobe. Does anyone have a suggestion?
Harry

Hi Harry,
Sorry, chat and phone support are closed on weekends for the video queue. We only have general support open on weekends. It's been this way for years. Sorry if that caused some inconvenience.
I hope you have solved your issue. If on Mac, you can update NVIDIA drivers in the NVIDIA control panel in System Preferences. AMD GPUs are merely updated when you update OS X.
Also, please check out the doc that was recommended: Installation failed. Error U44M1P7 | Updates
If you are still having trouble, contact us Monday through Friday 7AM-7PM PST here: Contact Customer Care
If you can't get your issue solved, send me a PM and I'll try and help.
BTW, I am not sure why your post is marked as correct. I do have that ability but did not do that. Sorry for that.
Thanks,
Kevin

Oracle VM Template for Enterprise Manager Cloud Control 12c Media Pack v1

Hello
I download Oracle VM Template for Enterprise Manager Cloud Control 12c Media Pack v1
I was checking the structure and I found this
[oracle@em12c bin]$ cd /u01
[oracle@em12c u01]$ ls
app lost+found OracleHomes oracle-template.sh scripts
[oracle@em12c u01]$ cd OracleHomes/
[oracle@em12c OracleHomes]$ ls
checkpoints db11g Middleware
[oracle@em12c OracleHomes]$ pwd
/u01/OracleHomes
[oracle@em12c OracleHomes]$ cd db11g/
[oracle@em12c db11g]$ ls
admin cfgtoollogs checkpoints diag fast_recovery_area oradata product
[oracle@em12c db11g]$ cd ..
[oracle@em12c OracleHomes]$ cd Middleware/
[oracle@em12c Middleware]$ ls
[oracle@em12c Middleware]$
The Database has all binaries but Middleware is empty
Same body knows about this issue.
Regards

Yes, you can install Oracle VM Manager, create a server pool with the one parent Oracle VM server in it, and then deploy the Oracle VM template in the pool. Once EM VM is up and running, you can register the same Oracle VM Manager with EM, to manage the pool.
In general, it is not recommended that you use the OVM server backend directly. But for bootstrapping the EM environment, you can also try the following:
Download the OVM Template on the Oracle VM server. From the OVM server terminal itself you can do "xm create" to spin a new virtual machine using the Oracle VM teamplate. Once the VM comes up, VNC into the VM and configure the EM OMS and agent.

Need help with my Toshiba remote control and receiver for Qosmio G30 161

Hello to all
I have a Toshiba Qosmio G30-161 and with it I have a Toshiba remote control and a Toshiba remote control receiver, this is the first time I have used it (tried to that is), my problem is the remote is not working on the computer when I press any program buttons the computer does nothing.
I have installed four brand new AA batteries and the remote works fine its sending signals to the receiver, the receiver the detecting the remote as a red light appears every time you press a button and as for the computer I have checked the drivers and the USB is picking up the receiver as a E-home remote receiver which I have checked with Toshiba and that is correct, so all in all the remote is working, the receiver is picking up signals and the pc has detected the receiver but nothing works, I have installed remote control manager but this still has done anything. I have spoken to Toshiba help and support and the end result is they are not sure what the problem is. Can anyone help I require the remote for slideshows for customers as I??m a photographer.
Also to confirm I am running Windows XP MCE addition.
Anthony Worlock

Hi there,
this remote contol works, if you use it without any special drivers and special software, only in the Media Center.
But if you install such stuff like [WinLirc|winlirc.sourceforge.net] then you should be able to get some functions for your presentation.
Please try this tool and check if it works.
By the way: If I were you I would first read the Manual and FAQ of WinLirc before starting because its a little bit tricky to handle the program. :) (Too many settings :D)
Greets

Installation VCS Control and Expressway vmware applications on one BE6000

Hello Community,
I want to buy one BE6000 and additional VCS Expressway vmware application. Then I'm going to deploy VCS Control vmware application and VCS Expressway vmware application on this BE6000. Also I plan to place this BE6000 in the DMZ.
Please help me, may I do that kind of deployment - VCS Control and Expressway vmware applications on ONE BE6000 ?
Thanks in advance.
Regards, Maksim.

The BE6000 supports VCS-c I belive you would need a seperate box for the VCS-e
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps11369/at_a_glance_c45-720492.pdf
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/BE6000/InstallationGuide/9_x/CUCM_BK_IA4BAD3A_00_installing-cisco-business-edition-6000.pdf
Also I would check Cisco site for the new Co-residency Policy Requirements
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/BE6000/Coresidency/9_x/BE6K_coRes.html

CUCM 10.5 Encrypted control and media

Similar Messages

Maybe you are looking for