CUCM 6 with MeetingPlace Express
Hello,
I have CUCM 6.1 integrated with MeetingPlace Express VT and everything is set up. However, when I test with trying to conference more than 2 users the video ends on everybody's desktop. When it is just 2 users the video shows up fine as soon as I conference in the next person it kicks the video off. Any help would be appreciated
Thanks!
Sorry, forgot to mention that I have configured everything in CUCM and Meetingplace and created the Video conference bridge and added it to the MRGL. It shows the bridge as registered in both CUCM & MPE
Thanks!
Similar Messages
-
Ports with MeetingPlace Express
Hello There,
Am I right if I say the number of ports that we use on MPE only count towards outside parties and that we essentially had unlimited use for internal people. Let's say I schedule a meeting for 4 people, 2 from inside and 2 from outside, do I need to reserve 4 ports or just 2?
Thanks,Hi Bahman,
Ports are like licenses in MPE and they do not differenciate between internal/external participants. So in your example you would need to reserve 4 ports. Here is some additional info;
About Voice Ports
Also called an access port, a voice port is used to connect a meeting participant to one or both of the following meeting interfaces:
Voice meeting Attend a meeting over the phone.
Lite web meeting View participant names and their status in a web interface.
About the Required Voice-Conferencing Licenses
The number of voice ports on a Cisco Unified MeetingPlace Express system is equal to the number of installed voice-conferencing licenses, up to 120 voice ports.
The number of voice ports is also the maximum possible number of the following connections:
Simultaneous voice meeting connections to Cisco Unified MeetingPlace Express.
Simultaneous web connections to lite web meeting rooms.
From this doc;
http://www.cisco.com/en/US/products/ps6533/products_administration_guide_chapter09186a0080579c3a.html#wp1083915
You can always configure users that have the ability to set up Zero-Port Voice Meetings but then you have no way of knowing if there will be sufficient voice ports available for their use.
About Zero-Port Voice Meetings
The following special characteristics apply to zero-port voice meetings:
No ports are reserved when zero-port voice meetings are scheduled. Therefore, there is no limit to the number of zero-port voice meetings that can be scheduled on Cisco Unified MeetingPlace Express at any time.
Users may join a zero-port voice meeting only if voice ports or voice floater ports are available at that time.
When a user joins a zero-port voice meeting, that user utilizes one voice port. Therefore, the number of meeting participants who can attend zero-port voice meetings at the same time is limited by the number of voice licenses that are installed and available on the system.
Users who can schedule zero-port voice meetings are always restricted from the following:
Scheduling full web meetings.
Reserving voice ports for scheduled meetings.
Hope this helps!
Rob
Please remember to rate helpful posts..... -
MeetingPlace Express strange problem !
Environment:
MeetingPlace Express 1.1.1.11
CallManager 4.1(3)sr2
Voice Gateway 1: 2821 (c2800nm-advipservicesk9-mz.124-4.T.bin) + VIC2-4FXO
Voice Gateway 2: 2621XM (c2600-advipservicesk9-mz.123-14.T5.bin) + NM-2V + 2* VIC-2FXO
VG1 connect to CallManager using H.323, VG2 connect to CallManager using MGCP
MeetingPlace Express connect to CallManager using H.323.
Problem:
When dial-in from PSTN to VG1 and VG2, both are well; but when using "Find-Me" feature, MeetingPlace express dial to user, users via VG2 are can sent dtmf with MeetingPlace Express, but users via VG1 can not sent any dtmf digit to MeetingPlace Express. So users via VG1 can not enter the meeting.For more information the following url would be useful,
http://www.cisco.com/en/US/products/ps6533/products_installation_guide_book09186a008057b547.html -
Can MeetingPlace Express make conference calls with just meeting ID and meeting password?
Hi,
We have MeetingPlace Express version 2.1.1.2. It is working fine and everything but we need to change the way it works.
For audio only conference calls, we need the users to be able to initiate meetings without having to enter their profile ID and profile password.
For example when a caller dials the MPE number and presses 1 to start a meeting, he has to enter his PIN code to be authorized to start a meeting, we want to exclude this feature, so that any one who dials the number and wants to start a meeting, he will get a meeting ID and meeting password directly.
Is this possible in MPE 2 ? Appreciate your help please, thanks in advance.I poked around a system I have nearby and can't find a setting that is an obvious choice for this one. I experience the same behavior at the 30 minute mark.
One alternate approach you may try is called a continuous meeting. The viability of this approach depends on how this is being used:
This likely will NOT work if you have lazy users who can't manage their time.
The reason is a continuous meeting always consumes the licenses for itself, even if there are not participants currently in it.
This may work if you have defined groups of users who repeatedly meet as a group in an ongoing manner.
A continuous meeting is a scheduled meeting that reserves ports and a meeting ID indefinitely, so that
participants may join the meeting at any time on any day. Nevertheless, a continuous meeting is in
session only when at least one participant is in the meeting.
I searched high-and-low for documentation on this and the only two items that I can turn up are these:
http://www.ciscosystems.org/en/US/docs/voice_ip_comm/meetingplace_express/1_1/english/administration/guide/bagmtgs.pdf (page five)
http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Express,_Release_2.x_--_How_to_Configure_Scheduled_and_Reservationless_Meetings#Enabling_Users_to_Schedule_Continuous_Meetings
One downer though: I cannot get the Continuous option to appear on my MPE 2.1.1.2 hotfix 36 (last release) system. Either I'm missing an option myself or something is wrong in this version. -
MeetingPlace Express 2.1.1.2 Dial Out was not Successful
I'm configuring a MeetingPlace Express v.2.1.1.2 and I can't make the MPX do the call to the guests of a meeting.
I make the configuration test in: Services > Logs > Verify Configuration > Call configuration verification and show the following error:
==============================================================
==============================================================
Call-Config Report
Summary
WARNING:The H.323 ID should match the host name
Valid E.164 Address has been configured
H.323 gateway has been configured
Error: Dial Out was not Successful
Call-Config Report Details
H.323 Details
H.323 enabled : YES
E.164 address : 196
H.323 ID : mpxadmin
H.323 gateway 1 : 010.145.002.030
SIP enabled : YES
DialOut Session Summary
VUI Configuration: 250 Sessions, 250 Confs
*** VUI INTERNAL STATUS UTILITY ***
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 4.
Enter destination for your call: The Telephone Number is 196. Len is 3
Do you want specific ports? (t -- F): You entered f.
Placing Call .....Call was unsuccessful: Ring No Answer.
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 0.
==============================================================
==============================================================
That parameter could check?
Here I place information on the configuration of my network:
CUCM v.7.0 --> 10.145.2.10
Voice Gatweay --> 10.145.2.30
In CUCM > Device > Gateway --> Gateway: 10.145.2.20 | Description: Cisco MeetingPlace Express | Type: H.323 Gateway | IP: 10.145.2.20
Please expect your valuable help!
Thanks a lot!
ErnestoGhi Ernesto,
As the problem you are facing is a dial out issue on MPE, go
through the checklist mentioned below in order to confirm the configuration
is intact.
Here is the checklist :
1. Ensure that H323 GW is defined on CCM/CUCM.
Device > Gateway > find.
Look for a device name that equals either MPE's hostname, FQDN, or IP
Address.
2. Ensure that h323 Gateways are configured on MPE.
MPE Administration Center > System Configuration > Call Configuration > H323
Configuration
Ensure that h323 is enabled.
Ensure that you have entered your CCM's IPs in h323 Gateway 1, 2
3. Ensure that CCM's interface with MPE is up.
Ensure that MPE's IP Address is listed under the "IP Address" column.
Ensure that this IP Address is that of the FIRST NIC on MPE, not the second.
4. Verify that MPE has the CSS required to call the destination.
FIRST, FIND MPE's CSS:
When MPE places a call, the CSS in question is Device > Gateway > MPE-GW >
Inbound
THEN the relevant config is under Device > "Call Routing Information -
Inbound Calls" > Calling Search Space
SECOND, FIND DESTINATION PATTERN's PARTITION:
If the destination is an IP Phone within the CCM/CUCM Cluster, then the
relevant config is under Device > Phone > click on Directory Number in CCM.
If the destination is a PSTN endpoint/phone, then the relevant config is
under Device > Route Pattern.
5. Ensure that your user profile is set to allow outdials.
MPE Administration Center > User Configuration > User Profile Management >
Your User Profile > Can call out of meetings should be set to "Yes".
6. When you place a call from from the CLI, the system applies permissions
from the "Guest" User profile since mpxadmin or root are not Users within
the MPX application. To allow this to work, you need to verify two
settings:
MPE Administration Center > User Configuration > User Profile Management >
Guest > Can call out of meetings should be set to "Yes".
Ensure that the Guest profile is not in a "locked" state.
MPE Administration Center > System Configuration > Usage Configuration >
Allow Guest outdials should be set to "Yes".
Hope this helps!
Thanks,
Karthik -
LDAP Integration issue- MeetingPlace Express 2.1.1.2
Hello ,
I have sucessfully installed Cisco Unified MeetingPlace Express 2.1.1.2
i can able to make audio/web conf .but i am unable to integrate with LDAP
while i am testing LDAP configuration i am getting below error
" Error while testing AXL configuration. Cisco Unified Communications Manager
is not available "
attached LDAP conguration and error
It would be great if any one can help me on this .
Thanks ,
SamThanks Java ,
The same document i followed for LDAP confguration .
previously it was working for few time .
RTMT logs i can able to see MPX contacting to CUCM .
Attacehd the RTMT AXL /MPX logs
Thanks ,
Sam -
Meetingplace express password recovery
Hi
Does anybody know what the procedure is to recover the mpxadmin password on MeetingPlace Express?Hi Nizar,
The passwords you are trying to reset is for the Application user, typically used for the initial setup of UCCX. This is not to be confused with the CCX Appadmin user that would be used to login to the GUI. Since you mentioned that the user was deleted from CUCM, you would recreate or use an existing user that is an "End User" in CUCM. Once you have created this user call into TAC and we can get root access to set UCCX back to FRESH_INSTALL, then run through the initial configuration to point at the newly created or existing user in CUCM.
Thank you,
Joe -
MeetingPlace Express without Cisco Unified Communications Manager
Hi Guys,
I need your inputs on using MeetingPlace Express without a PBX.
It's required for Audio, Video and Web conferencing for close to 50 ports.
The video endpoints will be H.323 based Video Devices (with audio capability).
I wanted to check if these devices can be registered directly to a Cisco IO Gatekeeper and have a trunk between MPE and GK. Not sure if this is feasible since there won't be any PBX.
I'll appreciate if someone can guide me for the feasibility of this option. If its feasible I would like to know how and what kind of limitations can be there?
I tried searching on NetPro but failed to find a post depicting this. If this is already asked earlier kindly guide me to the post.
-> Sushil7.1 is still supported, however 8.X was never tested with MPE as it was already going to be replaced with MP.
Since the BU never tested it, it falls under not supported, MP8 is supported with CUCM 8.
But, since it uses a standard H323 trunk it should work fine.
HTH
java
If this helps, please rate
www.cisco.com/go/pdihelpdesk -
Disk space problem on MeetingPlace Express
I get the email below daily. I'm thinking it's ok to cat /dev/null the cma.log file?
I also think I might be able to do the same thing to stdout.old?
Anything else I should try other than the instructions?
* Directory listing
[mpxadmin@meeting ConfSchd]$ ls -la
total 3036516
drwxrwxr-x 2 mpxadmin mpx 4096 Aug 2 13:27 .
drwxrwxr-x 17 root mpx 4096 Nov 4 2009 ..
-rw-rw-r-- 1 mpxadmin mpx 0 Nov 4 2009 ActConf.lk
-rw-rw-r-- 1 mpxadmin mpx 0 Nov 4 2009 Attach.lk
-rw-rw-r-- 1 mpxadmin mpx 4 Dec 22 2012 confId
-rw-rw-rw- 1 mpxadmin mpx 391 Apr 5 2010 pegstats
-rw-rw-r-- 1 mpxadmin mpx 255639 Aug 2 14:25 stderr
-rw-rw-r-- 1 mpxadmin mpx 1152127 Dec 22 2012 stderr.old
-rw-rw-r-- 1 mpxadmin mpx 516106727 Aug 2 16:50 stdout
-rw-rw-r-- 1 mpxadmin mpx 2588797008 Dec 22 2012 stdout.old
-rw-rw-r-- 1 mpxadmin mpx 0 Nov 4 2009 TCMap.lk
[mpxadmin@meeting ConfSchd]$
* EMAIL
This is an automated message from the MeetingPlace Express system with
hostname [meeting.afgrp.com] to inform you that disk space is low.
Details on where the problem is and how to resolve it are indicated below.
Low space in partition /. Percent used = [90].
The following files might cause trouble. However, inspect each one to make sure.
Look specifically for large files with old timestamps. Also, note that some of
the files indicated might have been previously mentioned. In this case, use the
prior instructions to handle these files rather than the instructions below.
If you are uncertain, contact Cisco TAC for confirmation/advice.
For the files below, use the following procedure to empty these files rather than
delete them outright.
1. For each file to be emptied do:
cat /dev/null > <filename>
2. After all files that you wish to empty have been emptied, do:
su // Enter 'root' password.
mpx_sys restart
-rw-rw-r-- 1 mpxadmin mpx 283120801 Apr 11 02:00 /var/mp/ConfSchd/stdout
-rw-r----- 1 root root 127007041 Dec 22 05:30 /var/spool/compaq/cma.log
In general, to free up disk space where it is uncertain exactly what files are in question,
do the following:
1. In general, go to places like /root, /mpxadmin, /tmp and do "ls -la" to look
for large files. If a file is large, old, and seems like some kind of log or
error file, it could be a candidate for deletion.
2. Generally files of type log (*.log), stderr, stdout, or txt (*.txt) are the
best candidates to look for. A good command to look for these types of
files with size of 10,000,000 bytes or larger is:
find / -name "<file type>" -exec ls -la {} ; | awk '{if( >=10000000) {print} }'
For example, to look for all log files 10,000,000 bytes or larger on
the entire system:
find / -name "*.log" -exec ls -la {} ; | awk '{if($5 >= 10000000) {print} }'
3. If you have a specific problem partition that you are trying to reduce size
for, do the following:
1. Find out the directory name of the top of the partition from "df".
2. "cd" to that location.
3. Then do: du -x -b --max-depth=1
4. Look for the directories that are really large.
5. Then "cd" into the worst subdirectory (or subdirectories).
6. Get a list of all large files from current directory location and lower:
(This example assumes 10,000,000 bytes and a check for .log files.
Note the starting location of '.' (current location) rather
than '/' (entire disk) ).
find . -name "*.log" -exec ls -la {} ; | awk '{if($5 >= 10000000) {print} }'
Complete output of the 'df' command:
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 6048320 5111204 629876 90% /
/dev/sda6 4032092 767336 3059932 21% /common
/dev/sda2 8064304 6492268 1162380 85% /db
/dev/sda9 256667 8416 234999 4% /grub
/dev/sda7 122154520 110696 115838720 1% /mpx-record
/dev/sda5 5036284 3577128 1203324 75% /opt
/dev/sda3 6048352 109032 5632080 2% /partB
none 1026932 22624 1004308 3% /dev/shmHi Josh,
It seems that the root partition of the MeetingPlace Express server is almost full. I have attached a document for your reference which can be used to minimize the disk space issues.
Once the steps mentioned in the attached document are completed, run the command "df" to check the disk space.
If you do not see much improvement in the root partition, then in that case some other files might need to be removed from the server to increase the root partition space.
If any of the partitions reach upto 90% or above, then the server might behave unexpectedly.
Feel free to revert if you have face any issues or have any queries.
Regards,
Rishabh -
MeetingPlace Express Assistance
Hi All,
We have MeetingPlace Express version 2.1.1.2.
We need to configure it to accept any user to make a non-scheduled conference directly, without requesting the user to enter his profile ID and profile password, and without the need to add the data of the users into the MeetingPlace.
We just need it to act as an audio conference bridge, so we need the user to dial the MeetingPlace number, then he can enter a certain password (one password for all our staff) to enable our employees to log into the MeetingPlace, and then get the Meeting ID and Meeting password and start the meeting.Sherif,
You are going to want to export using all of the headers and leaving them intact in the import file. You will want to follow the steps below for a successful import as the system is really sensitive that the data is formatted a certain way.
Create a test user profile in MPE manually so that you can get the file format of the import file with the headers.
Export User Profiles.
Export this test user profile to a file and include the header information.
This will create a User_Profiles.txt file that you will save and then open up in Excel. (Follow these steps below to ensure that the file is formatted correctly)
1. Within Excel, click on the Open tool on the toolbar. Excel displays the Open dialog box. (To display this dialog box in Excel 2007/2010, click the Office button and then click on Open.)
2. Using the Files of Type drop-down list at the bottom of the dialog box, indicate that you want to open Text Files (*.prn; *.txt; *.csv).
3. Select the saved export file.
4. Click on Open. Excel starts the Text Import Wizard, displaying the Step 1 of 3 dialog box.
5. Make sure the Delimited choice is selected, then click on Next. Excel displays the Step 2 of 3 dialog box.
6. Select Comma as a delimiter, then click on Next. Excel displays the Step 3 of 3 dialog box.
7. Click on Finish. Your file is imported.
8. Once the file is opened up in Excel, import your users into this spreadsheet so that they conform to the necessary format and the required headers.Next, find the "isLocalUser" field and set the parameter value for al user profiles from "No' to 'Yes'. Then find the EncryptedProfilePWD and EncryptedUserPWD fields. Remove the 'Encrypted' portion of the field name in the header so that they now read ProfilePWD and UserPWD. Make sure the value for the ProfilePWD for these user profiles is a standard alpha password. (cisco) Then make sure the value for the UserPWD for these user profiles is a standard numeric password. (12345). You may just be able to leave them as they are from your import.
9. Save the file with the changes.
10. Go to the Application MPE Web Page and then Maintenance-->Import Data-->Import User Profiles.
11. Select 'Add Profiles To System', select file to import, and set Overwrite field to 'Yes". (You should also set the log information to file option.)
12. Hit 'Execute' to import the user profiles to the system.
13. Once this is completed successfully, then go check the User Profile configuration to ensure that all users are imported correctly into MPE.
If you run into any problems with this procedure, please open an SR with TAC so that we can assist further.
Thank You,
Gerry -
MeetingPlace Express User ID Change
I am running MeetingPlace Express 2.1.1.2 and it is AD/CCM Integrated. We in the process of changing our AD User login ID and I may have run into a problem. From Call Manager perspective I just perform a full sync and it is good when a change is made.
However I cannot modify the user ID in Meeting Place Express.In reading the on line help, it says "Deleting a user profile also results in the removal of all meetings scheduled by that user from the end-user web interface; however, any meetings scheduled by that user still exist in the system" Does that not contradict itself?
When I add the user back with the same profile ID, will it re-associate the scheduled meetings? Also, is there a way to manually modify/sync the user id rather than deleting and re-adding?
Thanks, in advance.
DougI still don't understand how and when you are encountering that obstacle, but nevertheless if you cannot surmount it you will have to solicit Apple's help.
Apple can reset your iPhone if you present them its original, dated sales receipt. I believe you will have to do that in person at an Apple Store or an Apple Authorised Service Provider. -
MeetingPlace Express callout feature not working
Hello ,
we have Cisco Unified MeetingPlace Express 2.1.1.2 .
I am able to make audio/web confrence .
But call out facility is not working .
Please let me know what configuration need to be done for getting call out facility on CUMP
Below call out features are not working .
1-Call -alram
2-operator assistence while dialing 0
3-dialing from webconf
4- dialing from phone view
CUCM version 7.1
Meeting place i have confifured as h.323 h/w in CUCM
Thanks ,
ShaijalHello,
After restarting CUMP server my problem got resolved .
I gave below command to restart the system from the root .
/sbin/shutdown/ -r now
Thanks,
Shaijal -
MeetingPlace Express 7 or 8 basic audio only solution...help!
I have a customer with an existing UC 7.1.x cluster (a la carte licence) and a legacy MeetingPlace Express 2.1.1.2 solution providing audio conferencing only. The customer now wishes to up-grade the MeetingPlace solution to a latter version for support purposes and to increase the number of ports.
All that is required is the ability to schedule audio conferences and hold ad-hoc meetings; the solution requires 52 audio ports. There are no requirements for Webex external meetings, web or video; all that’s needed is simple audio bridging.
Am I right in thinking that the MCS Node for MP8 has no Webx VoIP/Video support, is an internal solution and is deployed on a single server (MCS)? Looking at various Cisco docs it’s also suggested that a Webex account is still required as MediaTone is extended to site?
Any advise would be greatly received!seanare wrote:
Thank you, as I noted here, your post was the key to my getting a Windows 8 SecureBooting setup on a W530.
In the case of Windows 8, I needed to copy the files away, reformat my USB key as FAT32 and copy the files back, and viola I was able to boot from my USB install media with the BIOS set to only boot UEFI. From there, there rest was easy (for Windows 8, the copying and renaming is not necessary, the key is having a FAT32 partition on the USB media, rather than an NTFS one; the EFI files are already in the right location).
Thank you again good sir.
You are welcome... and I'm happy that the change of the file system helps with windows 8 too. Thanks for confirming that.
abvasili
I'm just a volunteer. I like to help others where I can. Do my ideas work? I hope so. o_O
Who helped you today? Do not forget to thank him.
My hardware: TP x120e 0596-2ru. Windows 7, sp1, 64Bit, English, installed in UEFI mode. -
MeetingPlace Express 1.1 NFR Installation Problems
Hi.
On the installation guide of meetingplace express shows the MCS 7825H-3.0-IPC1 as a supported server and the DVD should be capable of booting itself and install the Linux OS and then the Cisco Application.
I'm trying to install the NFR in an MCS-7825H-800 instead of the MCS 7825H-3.0-IPC1 but the DVD will not boot automatically. The MCS-7825H-800 comes with a CD ROM but I changed it to a DVD ROM. Any ideas? I don't have an MCS 7825H-3.0-IPC1 at the moment and I would like to install the MeetingPlace Express NFR to test it out.
Thanks in advanced,
-JoseInstalling Cisco MeetingPlace Express, refer to the
http://www.cisco.com/en/US/products/ps6533/products_installation_guide_chapter09186a00805a7988.html#wp1164664
http://www.cisco.com/en/US/products/ps6533/products_installation_guide_book09186a008057b547.html -
Meetingplace express 1.2 voice only meetings
Is there a way to schedule voice only meetings in Meetingplace express 1.2?
We seem to only be able to schedule Voice+Web.
Thanks,
AndyHi Andy,
I looked into this once before and never came up with an answer :) but it looks like Ginger came up with an excellent one! Have a look at this thread;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=Unified%20Communications%20Applications&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dddf711/0#selected_message
Hope this helps!
Rob
Maybe you are looking for
-
Java.lang.NullPointerException - trying to deploy a mapping
Environment: OWB Tahoe Development Version 11.2.0.1 on Windows 7 Oracle 11.2.0.2 EE on AIX - Repository and all target tables I have imported metadata from older version of OWB and have been able to successfully deploy most all the other objects, fun
-
Issue in Nokia 6300 Software version 5.0
After upgrading my phone software succesfully to version 5.0 i have found that i cannot turn my cell to silent profile by pressing " # " button for few seconds. Is there any solution to this , if not , then how to restore the phone back to version 4.
-
Hi guys, I am creating an application with FORMS RUNTIME. Now, in one of my forms I need to create a button that pops up some kind of LOV or POPLIST or whatever it is, with the possible PRINTERS for the machine. Is there some sort of built in, ora an
-
How to display error message on the screen
I am new to WD world and need all possible steps to resolve the following issue. I need to display the error message on the screen if any required field is empty when user click on SAVE button. I have set the attribute GO_MESSAGE_MANAGER and check th
-
My Oracle Support - Oracle TEXT - Community
Hi all, It is my pleasure to announce the launch of the Oracle Text community on My Oracle Support. Communities are "Oracle's multi-channel platform for online collaborative support", accessible by all Oracle customers, partners and employees. They r