CUCM migration to version 10
Hi all
I am running a BE6k system with CUCM and CUC v9.1.2. In order to take advatage of the new feaures that CUCM and CUC version have, I have decided to migrate to version 10, but I am facing a migration issue. According to the upgrade guide, the migration from 9.x to 10 is a Refresh Upgrade (the underlying Red Hat operating system has to be upgraded) and I have to use Cisco Prime Collaboration Deployment. The ova image file for that is pcd_vApp_UCOS_10.0.1.10000-14_vmv7_v1.0.ova but I cannot find it anywhere. Moreover I cannot also find any iso images of the CUCM installation .Am I missing something??
Thank you in advance
Hi,
[+5] for Jaime.
You can also refer the discussion held for CUCM10.
https://supportforums.cisco.com/discussion/12103966/ask-expert-cisco-unified-communications-manager-cucm-version-100
regds,
aman
Similar Messages
-
Does anybody have a copy of the above referenced presentation that you could send me.
Thanks in advanced.
The presentation can be purchased at the following site:
http://www.scribd.com/doc/33211957/BRKVVT-2011-Best-Practices-for-Migrating-Previous-Versions-of-Cisco-Unified-Communications#archive
but felt I ask one of my peeps first.
Thanks in advanced.
DennisHi Dennis,
Well..let's give this a try
Cheers!
Rob -
Can CUCM 8.5 version be installed on a DL 380 G5 server in Virtual environment (Vmware Esxi 4.0 or 4.1)? Or does it have to be only installed in UCS boxes for VMware?
1. If the installation is possible for the Vmware instance on a DL 380 G5/G6 server , will that be supported by Cisco ?
Similary is the case with CUIC 8.5. Has anybody worked on these do suggest ideas.Virtualized UC applications from Cisco are only supported on the UC on UCS platform using ESXi 4.0, 4.0 Update 1, or 4.1 - hypervisor support may vary based on application.
Hailey
Please rate helpful posts!
Sent from Cisco Technical Support iPhone App -
Hi ,
I am getting the below error on RTMT on CUCM 9.1 Version running on MCS 7835-I3-K9-CMD2 Error
At Sat May 24 03:12:40 IST 2014 on node , the following HardwareFailure events generated:
hwStringMatch : May 24 03:12:23 ASHISH-CM01 daemon 4 Director Agent:
LSIESG_AlertIndication 500605B005F63930 Consistency Check inconsistency logging disabled on VD 00/0 (too many inconsistencies) Sev: 3.
AppID : Cisco Syslog Agent
ClusterID :
NodeID : ASHISH-CM01
TimeStamp : Sat May 24 03:12:23 IST 2014
hwStringMatch : May 24 03:12:23 ASHISH-CM01 daemon 4 Director Agent:
LSIESG_StorageVolume_Modified 500605B005F63930 Consistency Check inconsistency logging disabled on VD 00/0 (too many inconsistencies) Sev: 3.
AppID : Cisco Syslog Agent
ClusterID :
NodeID : ASHISH-CM01
TimeStamp : Sat May 24 03:12:24 IST 2014
Does anybody has any idea on the same.
Your inputs would be appreciated ..
Regards,
Ashish BaglaHello,
Did you find the origins of the alerts? I have the same on 2 defferent servers about at the same time of the night a Saturday night too.
Looks like bug CSCts69041
Thansk,
Hervé Jacquemin -
Error:Package migration from version 8 to version 6 failed with error 0xC001700A
I was about to post a similar question where the package runs fine on VS2013 but errors when I run DTEXEC from the command prompt.
Error:
Code: 0xC0016020
Source: Package
Description: Package migration from version 8 to version 6 failed with error 0xC001700AHi TheDenver,
Based on the error message that “Package migration from version 8 to version 6 failed with error 0xC001700A ", we can infer that the underlying cause is that the current SSIS package is created in SSDT BI 2014 for Visual Studio 2013, while you are trying
to execute it with SQL Server 2012 DTEXEC. It seems that SQL Server 2014 Integration Services (SSIS) is installed on a machine that has SQL Server 2012 Integration Services (SSIS) installed, multiple versions of the dtexec utility are installed.
SSIS versions are not backwards compatible. SSDT BI for VS 2013 is used for SQL Server 2014, SSDT BI for VS 2012/SSDT 2010 is used for SQL Server 2012. Please notice that once a package is upgraded from SSIS 2012 package schema to SSIS 2014 package schema,
the package cannot be downgraded. So we cannot open or execute the SSIS 2014 packages with SSIS 2012 anymore.
To fix this, please ensure that you run the correct version of the utility, at the command prompt run the utility by entering the full path (<drive>:\Program Files\Microsoft SQL Server\120\DTS\Binn).
Reference:
dtexec Utility
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support -
Data Export error when migrating cucm cluster on version 7.1.5 to cucm 10.0
Hi
Has anyone come across below? If so any suggestions for workaround?
01, 2014 11:54 PDT
STATUS
The task has been scheduled.
Oct 01, 2014 11:54 PDT
INFO
Export task action ID #154 with 1 node(s) scheduled.
Oct 01, 2014 11:54 PDT
STATUS
The task has started.
Oct 01, 2014 11:54 PDT
INFO
Export task action ID #154 with 1 node(s) started.
Oct 01, 2014 11:54 PDT
INFO
Export job for node xx.xx.xx started.
Oct 01, 2014 12:09 PDT
ERROR
Data export failed for node xx.xx.xx.
Oct 01, 2014 12:09 PDT
ERROR
Export job for node xx.xx.xx failed.
Oct 01, 2014 12:09 PDT
ERROR
1 nodes(s) in Export task action ID #154 failed: xx.xx.xx
Oct 01, 2014 12:09 PDT
ERROR
Task paused due to task action failures.Hi,
you can login PCD through putty for seeing the logs
file list activelog tomcat/logs/ucmap/log4j/ detail date
further, run
file tail activelog tomcat/logs/ucmap/logs4j/ucmap00001.log[for example]
regds,
aman -
Error while migrating from version 9201 to 9204
Actully i m migrating the Oracle 9201 to 9204,
now after installing only 9201,
1. I created the database and checked, everything was working fine.
2. i shutdown the database.
3. check, still some processes related to oracle like (HTTP server) were running,
4. i started upgrated to 9204, the process of updating the files FAILS 10-15 times, as i IGNORE that.
5. After uncessfully completing the path i logged to sqlplus giving error as
$ sqlplus
SQL*Plus: Release 9.2.0.4.0 - Production on Wed Feb 22 16:51:42 2006
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
Enter user-name: / as sysdba
/usr/lib/pa20_64/dld.sl: Unsatisfied data symbol 'kglla62_' in load module '/user04/oracle9i/OraHome1/bin/oracle'.
ERROR:
ORA-12547: TNS:lost contact
Now i rebotted the server, and that error (updating the files) wont come.
again the same error is coming as
/usr/lib/pa20_64/dld.sl: Unsatisfied data symbol 'kglla62_' in load module '/user04/oracle9i/OraHome1/bin/oracle'.
ERROR:
ORA-12547: TNS:lost contact
What could be the problem.$ echo $ORACLE_SID
iobasnov
$ echo $ORACLE_HOME
/user04/oracle9i/OraHome1
$ echo #^?$LD_LIBRAR^?^?^?
$ echo $LD_LIBRARY_PATH
/user04/oracle9i/OraHome1/lib:/usr/lib
$ echo $SHLIB_PATH
/user04/oracle9i/OraHome1/lib32:/usr/lib
$ sqlplus
SQL*Plus: Release 9.2.0.4.0 - Production on Wed Feb 22 17:39:26 2006
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
Enter user-name: / as sysdba
/usr/lib/pa20_64/dld.sl: Unsatisfied data symbol 'kglla62_' in load module '/use
r04/oracle9i/OraHome1/bin/oracle'.
ERROR:
ORA-12547: TNS:lost contact
also
$ tnsping
TNS Ping Utility for HPUX: Version 9.2.0.4.0 - Production on 22-FEB-2006 17:40:3
9
Copyright (c) 1997 Oracle Corporation. All rights reserved.
TNS-03502: Insufficient arguments. Usage: tnsping <address> [<count>]
$
Also cheked
http://forums1.itrc.hp.com/service/forums/questionanswer.do?admit=716493758+1099308719485+28353475&threadId=433749
i think i need to DEINSTALL 9201 and INSTALL again.... -
OIM Migration from version 9.1.0 to 9.1.0.2
Hello Everybody,
I'm working in a migration process of Oracle Identity Manager from 9.1.0 to 9.1.0.1 and them to 9.1.0.2.
The process works Ok with the core of OIM but we having a problem with the migration of the AD connector.
At the first time, we applied the process directly (according to the oracle documentation) and the object "user" looks corrupt.
We call Oracle and they told us that the correct way to install a new version of the connector is importing it from a OIM new instalation (with the new connector), but this process corrupt the object "user".
Did somebody work in a OIM migration process? Does somebody know the correct way to migrate OIM?
Thanks.
Regards.
Walter.First you need to determine the Upgrade Path and methods available to the New Oracle Database 10g Release.
http://download.oracle.com/docs/cd/B19306_01/server.102/b14238/preup.htm#i1007814
Refer the Oracle Upgrade Documentations on more information.
Oracle® Database Upgrade Guide 10g Release 2 (10.2)
http://download.oracle.com/docs/cd/B19306_01/server.102/b14238/toc.htm
Regards,
Sabdar Syed. -
Hi,
Current Version
Hyperion Version 11.1.1.3
Database: SQL Server 2005
Windows Server 2003 R2
Old Version
Hyperion Version 9.3.1
Database: SQL Server 2000
Windows Server 2000 R2
1.I have created classical planning applicationin(CPLAN) in the 11.1.1.3 which similar to 9.31 application, interms of application name, database names and dimensions.
2.I took backup of CPLAN of 11, and CPLAN of 931.
3.stopped planning, Essbase , RMI Registry, Shared services.
4.Restored the 931 CPLAN Backup( of SQLServer 2000) into 11113 CPLAN(SQL Server 2005)
5.HSP_OBJECT table - in this table object id column and objectname column is password, Here tried with both old password hypadmin and new password admin.
6.HSP_USERS table - USER _ID =50001 and SID= (I given 11 version details)
7. HSP_SYSTEMCFG Table- I tried with changing the VERSION from 9 to 11 and cleared the verion - tried with both the ways
and EIE_SERVER changed- this is shared service path with port number and server name changed.
I mean http://mycurrent server:28080/interop.
8. Above These3 Tables columns changed and started the services all planning etc.
9. tried to open planning web, i got the application CPLAN name, once enter the username and password and CPLAN , its giving error. the error message , error while processing this current page, check the log for details. I got this error message.
10. I checked the logs, Access.log, and Hyperion Planning.log these two logs verified i didnot find any error.
--please help meon this who has done this kind of migration. ASAP.
Thanks
Chinna
Edited by: Hyperion Chinna on Aug 12, 2010 4:45 PMMake sure you follow the steps here :- Migration of Hyperion Planning Application
Do not start changing anything in HSP_SYSTEMCFG
Cheers
John
http://john-goodwin.blogspot.com/ -
BE6000 CUCM 9.1 version licensing query
Hi All,
We have a BE6000 with CUCM 9.1 and UCL enhanced license subscription for 3 years. Can somebody help me understand what we need to do at the end of 3 years? Do we need to renew the licenses or do we have to purchase new licenses all together.
ThanksOnce you purchase the licenses, it stays with you and does not expire. However, if you do not keep your UCSS current and smartnet subscriptions, you will not be able to upgrade to version 10 or higher. (after three years). If you let it expire, Cisco usually has a program in place to allow the customer "get well" or "get current" for subscriptions. Instead of buying new licenses, you will be required to buy upgrades or renew your subscription at a higher price.
In a nutshell, stay current on your UCSS and SmartNet contracts and you will be fine. -
Hi all
I would like to know the migration of a project from higher version to lower version
for example PeopleTools 8.49 or 8.48 to PeopleTools 8.43 or 8.44 or 8.45
and the application HR 9.0 or8.9 to HR8.8
Any idea of this !
Look forward to here you.
Thank You.jim.marion wrote:
I believe the ini file Nicolas is referring to exists when you export a project to file (I didn't see mention of exporting the project to a file in this thread).
If you export a project to a file, then you should be able to import it into another tools release. If you do this, just be sure the project does not contain any PeopleTools definitions.Yes, this is what I was refering to, copy project to a file, modify the .ini (at least that was required on old PT version) as I explained before importing into target. Note if I already tested many time to move project from lower to higher PT version with this methid I never tested it from higher to lower version.
Furthermore, need to be tested, validated, and I'm not really sure it is a supported way (modify PT release in .ini file) to copy project accross version.
Nicolas. -
Migrating Crystal version 9.2 to Business Objects
Is there a target version of BO where I can simply make use of my existing Crystal reports.
Hey Alan,
You can migrate your Cr 9.2 version reports to Crystal XI R2 version.
But it is individual product /seperate installation as crystal designer not included in Business Objects installation.
You can run reports and upgrade to latest version CR 2008.
Thanks,
Navin. -
Variants not migrated to Version 7
Hi everyone,
We successfully did our technical upgrade and are in the process of migrating all the queries and workbooks to Version 7.0. We used the migrating of variants programs during the initial technical upgrade and have no problem seeing the variants in Version 3.x of the reports and workbooks.
We don't see any variants when we run the reports after they have been migrated. The old 3.x variants are showing up in the RSRVARIANT, RSRVARIANTDIR and RSRVARIANTVIEW tables. I believe the variants should be in the RSPARAMETRIZA and RSPARAMETRIZAT tables - but these are blank.
We tried migrating the variants again and get an error that they could not be migrated.
Did anyone have this issue? If so, please let me know!
Thanks
KathleenHi Pratik,
It turns out that we were missing authorizations! We needed to have full access to the authorization object S_RS_PARAM. In fact, users need to have this object as well, otherwise they won't see their parameters.
When you run the program to migrate the variants, if you don't have the authorizations for changing (we only had display) then the migration will not be done.
We re-did it after and now everything is fine!
Hope this helps!
Kathleen -
IPhoto migration. version issue
Have migrated my data from another iMac to new iMac.. When I open iPhoto on the new Mac I get a message that my photos are in a newer version of iPhoto and I need to open a new library or quit. Quit is only option. Upgraded s'ware and no change? IPhoto version on old mac is 5.3.2
Then you need to download this
http://support.apple.com/kb/DL1523
and run it before opening the Library. -
Hello guys,
I ran into a problem last week when trying to deploy our application on Weblogic 12c. (12.1.1). Until now our application was running on weblogic 10.3.4.
Several of our JPA queries do not compile/execute anymore due to the new eclipselink version : 2.3.1 embedded in weblogic 12.1.1.
On weblogic 10.3.4 the JPA queries work fine (eclipselink version 2.1.3). On 12c, with eclipselink version 2.3.1, we get a ORA-0904 error on several queries. Eclipselink 2.3.1 does not compile the query into a correct native SQL query (same problem as http://www-01.ibm.com/support/docview.wss?uid=swg24022303).
Error : Internal Exception: java.sql.SQLSyntaxErrorException: ORA-00904: "T5"."M_FOR_ID_LIE": invalid identifier
The JPA query :
SELECT DISTINCT cla FROM Classe cla, IN (cla.aet.formation.MVfos) mvfo
WHERE cla.ans = :ansCode
AND cla.lycee.id = :lyceeid
AND mvfo.ans = :ansCode AND cla.aet.niveauEtudes IN :nEtudes
// Is a child of me selected?
AND (EXISTS (SELECT mvfo2.id FROM MVfo mvfo2 WHERE mvfo.MFor.id = mvfo2.MFor.formationLie.id AND mvfo2.id IN :mvfoids)
// Is the parent of myself selected?
OR EXISTS(SELECT mvfo3.id FROM MVfo mvfo3 WHERE mvfo.MFor.formationLie.id = mvfo3.MFor.id AND mvfo3.id IN :mvfoids)
// Is a "brother" of myself selected (and it's not me)?
OR EXISTS(SELECT mvfo4.id FROM MVfo mvfo4 WHERE mvfo.MFor.formationLie.id = mvfo4.MFor.formationLie.id AND mvfo4.id IN :mvfoids AND mvfo.id <> mvfo4.id))
ORDER BY cla.code
The resulting SQL :
SELECT DISTINCT t0.ID, t0.ALIAS, t0.ANS, t0.CLOTURE_P1, t0.CLOTURE_P1_NOTES, t0.CLOTURE_P1_REGENT, t0.CLOTURE_P2, t0.CLOTURE_P2_NOTES, t0.CLOTURE_P2_REGENT, t0.CLOTURE_P3, t0.CLOTURE_P3_NOTES, t0.CLOTURE_P3_REGENT, t0.CODE, t0.CONSEIL_P1, t0.CONSEIL_P2, t0.CONSEIL_P3, t0.DEBUT_SAISIE_P1, t0.DEBUT_SAISIE_P2, t0.DEBUT_SAISIE_P3, t0.FIN_SAISIE_P1, t0.FIN_SAISIE_P2, t0.FIN_SAISIE_P3, t0.FORMATION_NB_HEURES, t0.FORMATION_TAUX_PRESENCE, t0.FORMATION_TITRE, t0.LECONS_P1, t0.LECONS_P2, t0.LECONS_P3, t0.MAX_ELEVES, t0.MIN_ELEVES, t0.TRI1, t0.TRI2, t0.TRI3, t0.TRI4, t0.TYPE_HORAIRE, t0.AET_ID, t0.LYC_ID, t0.ENS_ID
FROM AET t3, M_FOR t2, M_VFO t1, CLA t0
WHERE ((((((t0.ANS = ?) AND (t0.LYC_ID = ?)) AND (t1.ANS = ?)) AND (t3.NIVEAU_ETUDES IN (?,?,?,?)))
AND ((EXISTS (SELECT ? FROM M_FOR t7, M_FOR t6, M_FOR t5, M_VFO t4
WHERE (((t5.ID = t6.ID) AND (t4.ID IN (?))) AND (((t7.ID = t4.M_FOR_ID) AND (t5.ID = t1.M_FOR_ID)) AND (t6.ID = t7.M_FOR_ID_LIE))))
OR EXISTS (SELECT ? FROM M_FOR t10, M_FOR t9, M_VFO t8
WHERE (((t9.ID = t10.ID) AND (t8.ID IN (?))) AND ((t9.ID = t5.M_FOR_ID_LIE) AND (t10.ID = t8.M_FOR_ID)))) )
OR EXISTS (SELECT ? FROM M_VFO t11, M_FOR t13, M_FOR t12
WHERE ((((t9.ID = t12.ID) AND (t11.ID IN (?))) AND (t1.ID <> t11.ID)) AND ((t13.ID = t11.M_FOR_ID) AND (t12.ID = t13.M_FOR_ID_LIE)))) )) AND (((t3.ID = t0.AET_ID) AND (t2.ID = t3.M_FOR_ID)) AND (t1.M_FOR_ID = t2.ID)))
ORDER BY t0.CODE ASC
The JPA get's confused with the scoping of the M_FOR table. We use the same table again in different subqueries. T5 is reused in the second qubquery which is wrong (it's not in the FROM). and thus we get a ORA-0904 error.
So I was hoping that I could solve this problem by upgrading to JPA version 2.4.1 which I did using the following tutorial :
http://docs.oracle.com/cd/E23943_01/doc.1111/e25034/tlandwls.htm#BABEDCEI Section 2.3.3 Task 3: Update the Version of EclipseLink in WebLogic Server.
Basically I made a shared-library with the 2.4.1 JPA and reference it from our project.
With the 2.4.1 version I run into a org.eclipse.persistence.exceptions.JPQLException on A LOT of queries even before the queries are compiled into native sql:
I have simplified a query to make it understandable :
Caused by: Exception [EclipseLink-0] (Eclipse Persistence Services - 2.4.0.v20120608-r11652): org.eclipse.persistence.exceptions.JPQLException
Exception Description: Syntax error parsing [SELECT eleve FROM Eleve eleve WHERE CONCAT(eleve.nom, 'what is going on here') IN :modCodeList ].
The IN expression does not have a valid expression
I have the impression that the left side of a IN expression can't be a constant. If I put (eleve.nom IN :list) this query passes. If I put (1 in :list) the query fails for the same reason.
I have double checked the runtime version of eclipselink with:
logger.debug("ECLIPSELINK VERSION " + org.eclipse.persistence.Version.getVersionString());
So to summarize, I have native sql problems (incorrect sql) with versions 2.3.* and I have parsing exceptions with versions 2.4.0 and 2.4.1. I suppose that with versions 2.4.* I will run into the same native sql problems of versions 2.3.* once all the queries parse.
Versions 2.1.3 and 2.2.0 work.
Has anyone any idea or experience with migration problems of weblogic and/or eclipselink. Any help would be very appreciated.
Thanks in advance for your help.
DavidEclipseLink 2.4 uses the Hermes parser by default instead of the ANTLR parser used previously, so that might explain the parsing error differences. Both issues should be filed as bugs, but it might be that once the 2.4 parse error is fixed or a workaround provided to generate the correct SQL - the code generated by the two parsers can be slightly different.
But please file both issues with as simple a test case reproduction as possible, and remember to vote for each if filed on EclipseLink instead of through Oracle support.
Best Regards,
Chris
Maybe you are looking for
-
Logging with jdk1.4 - how to add a handler using configuration file
Hi, all I am playing around with java.util.logging in jdk1.4. In particular, I am using a properties file for configuration. However, one thing I couldn't do is to assign a handler, such as the ConsoleHandler, to the com.xyz.foo logger. Everything fo
-
How to add multiple namespaces in XSD ?
Can anyone tell me how to add multiple namespaces inside an XSD. Or how to import XSD into another XSD ?? Thanks
-
Flash button - linking to HTML page - weird problem
There could be a really easy solution for this, but I can't figure it out. I have a simple button that links to an anchor within an HTML page. Here the actionscript for the button: on (release) { getURL ("test.html#two"); when the button is pressed,
-
How can I use migration assistant to load my new Macbook Air?
How do I use migration assistant to load my new Macbook Air? Can this be done only wirelessly?
-
Is it possible to select only what part of a document you want to print
How can I print only the areas that I need from a document or an email?Is there a way to select part of the document and print only that? Thanks.