CUCM Mobility/Single Number Reach is not working correctly
Hi,
I'm experiencing difficulties with the CUCM Mobility (Single Number Reach) function.
For a customer of mine, I'm busy setting up the Mobility/Single Number Reach which is designed as follows:
- Users have a 4 digit DN that is attached to their User Device Profile so that they can use Extension Mobility.
- Those same users also have a Remote Destination Profile with a Remote Destination (to a mobile number) attached to their DN.
All has been set but as I was testing a couple of DNs, I noticed that a some numbers could be called to both their DN and Remote Destinations while others could only reach their DN.
As an example I have configured DN 6380 with the correct CSS (which permits to call to mobile phones and national numbers) to a User Device Profile.
That same DN is also connected to a Remote Destination Profile with a configured Remote Destination, which also has the same CSS.
The End User that is needed to login into Extention Mobility is 6380.
The settings on the Remote Destination are to ring always and all the time.
All Remote Destinations have the "Line Association" active.
Each DN has a value of 3 in maximum number of lines field.
Their Remote Destination profile has a value of 2 in maximum number of lines.
With this particular user, I'm sure that I have the right mobile number.
I already found out that the numbers that are having this problem, do not make a call to the PSTN and mobile network when their DN are called.
So I think the problem is within CUCM.
Can somebody help me?
Many thanks in advance!
The version of call manager is 8.6.2.20000-2.
I did a debug isdn q931 on the voice router which is connected to the PRI circuit.
A couple of test calls later and this is the output I got:
Jun 28 08:34:15.737: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0E5A
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18382
Preferred, Channel 2
Calling Party Number i = 0x2183, '51365XXXX'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '88777XXXX'
Plan:ISDN, Type:National
Sending Complete
Jun 28 08:34:15.749: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8E5A
Channel ID i = 0xA98382
Exclusive, Channel 2
This company has 200+ Mobility users so I did a random check.
Strangely enough, the one I described in my first post is now reachable on both his DN and mobile phone.
This is 4 digit number was the only one though.
Jun 28 08:09:20.557: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x00A6
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18382
Preferred, Channel 2
Calling Party Number i = 0x2181, '51365XXXX'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '88777XXXX'
Plan:ISDN, Type:National
High Layer Compat i = 0x9181
Sending Complete
Jun 28 08:09:20.569: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x80A6
Channel ID i = 0xA98382
Exclusive, Channel 2
Jun 28 08:09:20.573: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x2345
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839C
Exclusive, Channel 28
Display i = 'Testnummer'
Called Party Number i = 0x80, '51365XXXX'
Plan:Unknown, Type:Unknown
Redirecting Number i = 0x00008F, '088777XXXX'
Plan:Unknown, Type:Unknown
I did a Remote Destination Profile export of all records with a Remote Destination attached to it and then re-imported them in CUCM.
The last output of the call to the mobile phone was not appearing last Thursday.
Apparently, the export and import of the profiles and destinations did change something within CUCM.
Could this be a bug in CUCM?
Similar Messages
-
SIP Trunk - No voice with Single Number Reach
Hi Community.
I setup SIP Trunk with the CCA. Everything is working Call In and Call Out. Call Forward and so on.
But with Single Number reach is something wrong. The mobile phone is ringing and I can get the call, but I hear not any voice.
Can someone please help me out? Below the config.
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.1.1 10.1.1.9
ip dhcp excluded-address 10.1.1.241 10.1.1.255
ip dhcp pool phone
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
option 150 ip 10.1.1.1
ip domain name site1.365873.trk.ipvoip.ch
ip name-server 8.8.8.8
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
isdn switch-type basic-net3
voice call send-alert
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
sip
registrar server expires max 3600 min 3600
localhost dns:site1.365873.trk.ipvoip.ch
no update-callerid
voice class codec 1
codec preference 1 g711alaw
voice register global
mode cme
source-address 10.1.1.1 port 5060
load 9971 sip9971.9-2-2
load 9951 sip9951.9-2-2
load 8961 sip8961.9-2-2
timezone 23
voice source-group CCA_SIP_SOURCE_GROUP_CUE_CME
access-list 2
translation-profile incoming SIP_Incoming
voice source-group CCA_SIP_SOURCE_GROUP_EXTERNAL
access-list 3
voice translation-rule 9
rule 1 /0041449475090/ /90/
rule 2 /0041449475091/ /91/
rule 3 /0041449475092/ /92/
rule 4 /0041449475093/ /93/
rule 5 /0041449475094/ /94/
rule 6 /0041449475095/ /95/
rule 7 /0041449475096/ /96/
rule 8 /0041449475097/ /97/
rule 9 /0041449475098/ /98/
rule 10 /0041449475099/ /99/
voice translation-rule 410
rule 1 /^0\(.*\)/ /\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 411
rule 1 /^0\(.*\)/ /ABCD0\1/
voice translation-rule 412
rule 1 /^ABCD\(.*\)/ /\1/
voice translation-rule 422
rule 15 /^ABCD\(.*\)/ /\1/
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
rule 1 /^9\([1-9]\)$/ /004144947509\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 1112
rule 1 /^0/ //
voice translation-rule 2000
rule 1 /0041449475098/ /98/
voice translation-rule 2001
rule 1 /0041449475097/ /97/
voice translation-rule 2002
rule 1 /^6/ //
voice translation-rule 2222
voice translation-profile AA_Profile
translate called 2001
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PSTN_CallForwarding
translate redirect-target 410
translate redirect-called 410
voice translation-profile PSTN_Outgoing
translate calling 1111
translate called 1112
translate redirect-target 410
translate redirect-called 410
voice translation-profile SIP_Called_9
translate calling 3265
translate called 9
voice translation-profile SIP_Incoming
translate called 411
voice translation-profile SIP_Passthrough
translate called 412
voice translation-profile SIP_Passthrough_CallBlocking
translate called 422
voice translation-profile VM_Profile
translate called 2000
voice translation-profile XFER_TO_VM_PROFILE
translate redirect-called 2002
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
fax interface-type fax-mail
license udi pid UC540W-BRI-K9 sn FGL163220SL
archive
log config
logging enable
logging size 600
hidekeys
username admin privilege 15 secret xxx
username xxx password 0 ""
username xxx password 0 ""
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
no ip address
ip inspect SDM_LOW out
ip virtual-reassembly in
ip verify unicast reverse-path
load-interval 30
shutdown
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
no ip address
macro description cisco-desktop
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/8
no ip address
macro description cisco-desktop
spanning-tree portfast
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
no ip address
shutdown
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface Dot11Radio0/5/0
no ip address
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
antenna receive right
antenna transmit right
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
ip address 192.168.10.2 255.255.255.0
ip access-group 102 in
ip nat inside
ip virtual-reassembly in
interface BVI100
description $FW_INSIDE$
ip address 10.1.1.1 255.255.255.0
ip access-group 103 in
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.10.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.1.1.0 0.0.0.255
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 2 remark CCA_SIP_SOURCE_GROUP_ACL_INTERNAL
access-list 2 remark SDM_ACL Category=1
access-list 2 permit 192.168.10.2
access-list 2 permit 10.1.10.0 0.0.0.3
access-list 2 permit 192.168.10.0 0.0.0.255
access-list 2 permit 10.1.1.0 0.0.0.255
access-list 3 remark CCA_SIP_SOURCE_GROUP_ACL_EXTERNAL
access-list 3 remark SDM_ACL Category=1
access-list 3 permit 212.147.47.216
access-list 3 deny any
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 deny ip 10.1.1.0 0.0.0.255 any
access-list 101 deny ip 192.168.10.0 0.0.0.255 any
access-list 101 deny ip 192.168.1.0 0.0.0.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip 10.1.1.0 0.0.0.255 any
access-list 102 deny ip 192.168.1.0 0.0.0.255 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny ip 10.1.10.0 0.0.0.3 any
access-list 103 deny ip 192.168.10.0 0.0.0.255 any
access-list 103 deny ip 192.168.1.0 0.0.0.255 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 104 remark auto generated by SDM firewall configuration##NO_ACES_14##
access-list 104 remark SDM_ACL Category=1
access-list 104 deny ip 10.1.10.0 0.0.0.3 any
access-list 104 deny ip 10.1.1.0 0.0.0.255 any
access-list 104 permit ip any any
access-list 104 permit udp host 8.8.8.8 eq domain any
access-list 104 permit icmp any any echo-reply
access-list 104 permit icmp any any time-exceeded
access-list 104 permit icmp any any unreachable
access-list 104 deny ip 10.0.0.0 0.255.255.255 any
access-list 104 deny ip 172.16.0.0 0.15.255.255 any
access-list 104 deny ip 192.168.0.0 0.0.255.255 any
access-list 104 deny ip 127.0.0.0 0.255.255.255 any
access-list 104 deny ip host 255.255.255.255 any
access-list 104 deny ip host 0.0.0.0 any
access-list 104 deny ip any any
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone CH
station-id name FAX
station-id number 99
caller-id enable
voice-port 0/0/1
cptone CH
shutdown
caller-id enable
voice-port 0/0/2
cptone CH
shutdown
caller-id enable
voice-port 0/0/3
cptone CH
shutdown
caller-id enable
voice-port 0/1/0
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/1/1
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register mtpa4934c6ee4e0
dspfarm profile 2 transcode
description CCA transcoding for SIP Trunk VTX
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 10
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
destination-pattern 99
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 6 pots
description tcatch all dial peer for BRI/PRIv
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/1
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
translation-profile outgoing XFER_TO_VM_PROFILE
destination-pattern 98
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2001 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 97
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2012 voip
description ** cue prompt manager number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 96
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1000 voip
permission term
description ** Incoming call from SIP trunk (VTX) **
session protocol sipv2
session target sip-server
incoming called-number .%
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1001 voip
corlist outgoing call-local
description ** star code to SIP trunk (VTX) **
destination-pattern *..
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1003 voip
description ** Passthrough Inbound Calls for PSTN from CUE **
translation-profile incoming SIP_Passthrough
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ABCDT
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1005 voip
description ** Passthrough Inbound Calls for MWI from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number A80T
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1009 voip
description ** Passthrough Inbound Calls for Internal Extensions from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ^..$
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1033 voip
corlist outgoing call-local
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0187
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1042 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1041 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1025 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[789]1.......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1020 voip
corlist outgoing call-national
description **CCA*Switzerland*Regional Announcement VM**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01600
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1040 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 000333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1043 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1035 voip
corlist outgoing call-national
description **CCA*Switzerland*Mobile Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 007[46789].......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1024 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Personal Numbering**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00878......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1029 voip
corlist outgoing call-national
description **CCA*Switzerland*Voicemail Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00860.........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1036 voip
corlist outgoing call-national
description **CCA*Switzerland*VPN Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00869.............
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1027 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Premium Rate (Business)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00900......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1026 voip
corlist outgoing call-national
description **CCA*Switzerland*Test Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00868T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1034 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Shared Cost numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0084[0248]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1038 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1037 voip
corlist outgoing call-toll-free
description **CCA*Switzerland*Toll Free Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00800......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1039 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1032 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[23456]........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1023 voip
corlist outgoing call-international
description **CCA*Switzerland*International Calls**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 000T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1031 voip
description **CCA*Switzerland*Premium Rate (Social)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0090[16]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1030 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 014[0357]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1045 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1028 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Directory Enquiries**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 018[15].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1021 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 011[45].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1022 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01[67].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1044 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 2002 voip
description ** cue voicemail PSTN number **
translation-profile outgoing VM_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2003 voip
description ** cue auto attendant PSTN number **
translation-profile outgoing AA_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1110 pots
preference 9
destination-pattern xxx
port 0/0/0
no sip-register
dial-peer voice 3006 voip
description SIP
translation-profile incoming SIP_Called_9
session protocol sipv2
session target sip-server
incoming called-number xxx.
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
no dial-peer outbound status-check pots
sip-ua
keepalive target dns:site1.365873.trk.ipvoip.ch
authentication username xxx password 7 xxx
no remote-party-id
retry invite 2
retry register 10
timers connect 100
timers keepalive active 100
registrar dns:site1.365873.trk.ipvoip.ch expires 3600
sip-server dns:site1.365873.trk.ipvoip.ch
host-registrar
telephony-service
sdspfarm units 5
sdspfarm transcode sessions 10
sdspfarm tag 2 mtpa4934c6ee4e0
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.1.1 port 2000
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service phone ehookEnable 1
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message SwissT.Net
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.1/voiceview/authentication/authenticate.do
cnf-file location flash:
cnf-file perphone
user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
network-locale U4
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-5-4
load 501G spa50x-30x-7-5-2b
load 502G spa50x-30x-7-5-2b
load 504G spa50x-30x-7-5-2b
load 508G spa50x-30x-7-5-2b
load 509G spa50x-30x-7-5-2b
load 525G2 spa525g-7-5-4
load 301 spa50x-30x-7-5-2b
load 303 spa50x-30x-7-5-2b
time-zone 23
time-format 24
date-format dd-mm-yy
keepalive 30 auxiliary 4
voicemail 98
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 xxx
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
transfer-pattern 6.. blind
secondary-dialtone 0
night-service day Sun 17:00 09:00
night-service day Mon 17:00 09:00
night-service day Tue 17:00 09:00
night-service day Wed 17:00 09:00
night-service day Thu 17:00 09:00
night-service day Fri 17:00 09:00
night-service day Sat 17:00 09:00
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 1
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
service phone webAccess 0
softkeys remote-in-use Newcall
softkeys idle Redial Pickup Mobility Newcall Cfwdall Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer Mobility TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 15
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 16
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 17
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 18
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-dn 9
number BCD no-reg primary
description MoH
moh out-call ABC
ephone-dn 292
number xxx
description SIP Main Number registration
preference 10
ephone-dn 293 dual-line
number 90 secondary xxx no-reg both
label Zentrale
description 90
name Zentrale
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 294 dual-line
number 94 secondary xxx no-reg both
label LL
description Lehrling Lehrnende
name Lehrling Lehrnende
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 295 dual-line
number 93 secondary xxx no-reg both
label CM
description
name
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 296 dual-line
number 92 secondary xxx no-reg both
label EE
description
name
mobility
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 297 dual-line
number 91 secondary xxx no-reg both
label RS
description
name
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 298
number 6.. no-reg primary
description ***CCA XFER TO VM EXTENSION***
call-forward all 98
ephone-dn 299
number A801.. no-reg primary
mwi off
ephone-dn 300
number A800.. no-reg primary
mwi on
ephone 1
device-security-mode none
mac-address A44C.11A0.B648
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:296 2:293 3m297 4m295
button 5m294
ephone 2
device-security-mode none
mac-address A44C.11A0.B566
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:297 2:293 3m296 4m295
button 5m294
ephone 3
device-security-mode none
mac-address A44C.11A0.B5C4
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:295 2:293 3m297 4m296
button 5m294
ephone 4
device-security-mode none
mac-address A44C.11A0.B67A
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:294 2:293 3m297 4m296
button 5m295
alias exec cca_voice_mode PBX
alias exec cca_vm_notification schedule from_time=00 to_time=24
alias exec clid-ALL_BRI ;1:0-4;1:0-9;1:0-9;1:1-9
alias exec clid-SIP ;1:1-9;1:1-9;1:1-9
banner login ^CCisco Configuration Assistant. Version: 3.2 (3). Fri Jul 04 13:18:33 CEST 2014^C
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
transport preferred none
transport input all
line vty 5 100
transport preferred none
transport input all
ntp master
ntp server 91.240.0.5 prefer
enHi Patrick
I am working on this one as well. I have a UC560 with SIP Trunk provider Les.NET.
It was working fine until a few weeks ago when something changed on the provider end and broke it. My hunch it is something to do with the SIP REFER.
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
Here is an excerpt from the above page:
Call Transfer
When a call comes in on an SIP trunk to an SCCP Phone or CUE AutoAttendant (AA) and is transferred, the CME by default will send a SIP REFER message to the SP proxy. Most SP Proxy Servers do not support the REFER method. This needs to be configured in order to force the CME to hairpin the call:
Router(config)#voice service voip
Router(conf-voi-serv)#no supplementary-service sip refer
Figure 3 shows the behavior of the CME system with the REFER method disabled. -
Skype number is suddenly not working for me and my...
Skype number is suddenly not working for me and my colleagues to RECEIVE outside calls. Any ideas?
When I try to call my skype from my cell, it doesnt ring on either end. It appears connected on the cell phone since the counter clock for the call is increasing, but it doesnt ring or connect.
This is the same for me and at least 2 of my colleagues. It was working all day, till suddenly it did not.
When outside people call, it just gives us a missed call or voicemail email, but does not show a missed call on our skype.
When I call an outside number from skype, it connects.
Thanks for any help ASAP!I think this might have been happening to me earlier. If you wait like 30 seconds when you called a machine said "All circuits are busy. da da da". I was looking for an answer and google only brought stuff from like 2010. It's working now after an hour or so.
Sucks cause I use skype for work and was desperate to find a quick reponse but couldn't. -
Are mobile internet USB devices still not working on Snow Leopard?
Are mobile internet USB devices still not working on Snow Leopard? I actually had to go back to my previous operating system to get this to work. I would however prefer to use Snow Leopard...if Apple & HUAWEI have finally got their act together!
There appears to be a problem with drivers for USB wireless modems with 10.6. I upgraded from Leopard to Snow Leopard and now can't connect to the internet with my wireless modem. I hope Apple sort this out soon. Or maybe it's Huawei that needs to put a 10.6 driver into its software.
-
I received a tracking number that is not working!
I didn't not pre-order my iPhone 4s 16gb until yesterday afternoon. I immediately got an order confirmation e-mail. Later in the afternoon, I received an email saying that my order had been shipped via USPS and they gave me a tracking number which did not work. I assumed it wasn't working because of the holiday and no mail service. I checked again this morning and it still doesn't work! My bank account has still not been charged for my order, and when I check my order status on Verizon it states that its processing my order and the expected ship date is 10/21/11. Why would I get an email stating that my phone was shipped when everything else clearly contradicts that statement?
Others have reported getting a USPS Tracking #. Did you order any accessories? This would be the most likely explanation. Also note that the USPS is painfully slow in updating its tracking, sometimes its never updages, and other times it updates after the package has arrived. It's by far the worst tracking system there is and though it's gotten better, it still needs lots of improvement. And if you haven't been charged, it's most like not the phone. There are thousands upon thousands of people who ordered the 16GB at 3AM (or a little before) on Friday, and they haven't gotten their e-mails yet.
-
The Restriction option to NOT ALLOW CHANGES to Mobile or Cellular data does not work why is this ?
Hi there,
You may want to try force closing all open apps and resetting the device as an initial troubleshooting step. Take a look at the articles below for more information.
iOS: Force an app to close
http://support.apple.com/kb/ht5137
Turn your iOS device off and on (restart) and reset
http://support.apple.com/kb/ht1430
Additionally, you may want to try completely disabling and re-enabling restrictions.
-Griff W. -
I have a 2011 tahoe. My bluetooth functioned properly until I updated my iPhone. Now the iPhone connects to the Tahoe but when I try to call a number it does not work. Either it cals the number and has no outgoing or incoming sound or it just says it iis unable to complete the call.
I would check with the Auto dealer where the vehicle was purchased to check and see when the bluetooth software was last updated on your vehicle. With the vehicle being a 2011 and if the software has not been updated since the dropping of IOS 7 then obviously there will be software incompatibilities.
Good luck. -
If statement within a view is not working correctly ?
Hi all,
maybe i am wrong but i think the if statement within a view is not working correctly. See code down below.
I would like to use the Hallo World depending on the page attribute isFrame with or without all the neccessary html tags. Therefore i have embedded the htmlb tags in an if statement. But for any reason if isframe is initial it isn't working. It would be great if anybody could help me.
<%@page language="abap"%>
<%@extension name="htmlb" prefix="htmlb"%>
<% if not isframe is initial. %>
<htmlb:content design="design2003">
<htmlb:page title = "Top Level Navigation view">
<% endif. %>
hallo world
<% if not isframe is initial. %>
</htmlb:page>
</htmlb:content>
<% endif. %>
thanks in advance and best regards
Matthias HlubekMatthias,
The short answer: your example is <b>NOT</b> going to work. The long answer will probably 5 pages to describe. So first let me rewrite the example so that it could work, and then give a short version of the long answer. Do not be disappointed if it is not totally clear. It is rather complicated. (See the nice form of IF statements that are possible since 620.)
<%@page language="abap"%>
<%@extension name="htmlb" prefix="htmlb"%>
<% if isframe is <b>NOT</b> initial. %>
<htmlb:content design="design2003">
<htmlb:page title = "Top Level Navigation view">
hallo world
</htmlb:page>
</htmlb:content>
<% else. %>
hallo world
<% endif. %>
So why does your example not work? Let us start with a simple tag:
<htmlb:page title = "Top Level Navigation view">
</htmlb:page>
Now, for each tag, we have effectively the opening part (<htmlb:page>), an optional body, and then the closing part (</htmlb:page>). We are now at the level of the BSP runtime processing one tag. What the runtime does not know, is whether the tag wants to process its body or not. Each tag can decide dynamically at runtime whether the body should be processed. So the BSP compiler generates the following code:
DATA: tag TYPE REF TO cl_htmlb_page.
CREATE OBJECT tag.
tag->title = 'Top Level Navigation view'.
IF tag->DO_AT_BEGINNING( ) = CONTINUE.
ENDIF.
tag->DO_AT_END( ).
You should actually just debug your BSP code at ABAP level, and then you will immediately see all of this. Now, let us mix in your example with our code generation. First you simplified example:
<% if isframe is NOT initial. %>
<htmlb:page title = "Top Level Navigation view">
<% endif. %>
<% if isframe is NOT initial. %>
</htmlb:page>
<% endif. %>
And then with our generated code. Look specifically at how the IF/ENDIF blocks suddenly match!
if isframe is NOT initial.
DATA: tag TYPE REF TO cl_htmlb_page.
CREATE OBJECT tag.
tag->title = 'Top Level Navigation view'.
IF tag->DO_AT_BEGINNING( ) = CONTINUE.
endif.
if isframe is NOT initial.
ENDIF.
tag->DO_AT_END( ).
endif.
You can see that your ENDIF statements are closing IF blocks generated by the BSP compiler. Such a nesting will not work. This is a very short form of the problem, there are a number of variations, and different types of the same problem.
The only way to solve this problem, is probably to put the body into a page fragment and include it like I did above with the duplicate HelloWorld strings. But this duplicates source code. Better is to put body onto a view, that can be processed as required.
brian -
Hi Friends,
We have one Z report that output is displayed in ALV. We are using the standard FM 'REUSE_ALV_GRID_DISPLAY.
We have requirement to remove leading zeros for the field like Material Number (MATNR), Equipment Number (EQUNR) etc. We did the changes by applying the field catalog properties as below.
lw_fieldcat-lzero = space.
lw_fieldcat-no_zero = 'X'.
After this, the MATNR and EQUNR is displayed correctly in the ALV. (Leading zeros are suppressed). But, when we do filter for these fields, in the filter window it displays all the values with leading zeros.
1. We don't understand why it is showing in the Filter widow with all leading zeros. All it shows all the records instead of unique items.
Later on, we removed the above fieldcat coding. Then, we have called the CONVERSION_EXIT routines (in the domain) for the fields to remove leading zeros.
Now, the MATNR and EQUNR is displayed correctly (without leading zeros) in ALV. When we do filter, it is also doing filtering correctly. But, when we do filter which have EQUNR having long values (after zero suppression), it is not working correctly. i.e no items are displayed in the ALV.
Not only for this items. If we filter character columns which have long text, it is not filtering correctly.
2. It is not able to understand why the filtering is not working for long items. But in the standard report, the filtering is working correctly.
We are using SAP ECC 6.0.
Friends, can you clarify the about doubts. It is surprising for me.
Kind regards,
Jegathees P.
Our customer is asked to remove the leading zeros for the numeric fieldHi Clemens Li
I agreed on your point. When we define the Internal table the type for element EQUNR & QUMNR , we are referring the SAP data element for EQUNR, QMNUM field.
Our doubt is even though we refer the standard data element, in the ALV display, it shows with leading zeros and also it creates problems in the filtering and in the filter window all values instead of unique nos.
Hi Abhii
I have given below the fieldcat coding.
Friends, can you kindly clarify the above said problems. Since we use SAP ECC 6.0 any notes or patches apply is required. ( this is the basic functionality in ALV, that is my doubt).
wls_fieldcat-col_pos = wpv_pos.
wls_fieldcat-fieldname = wpv_champ.
wls_fieldcat-tabname = wlc_tabname.
wls_fieldcat-seltext_s = wls_fieldcat-seltext_m
wls_fieldcat-seltext_l = wpv_libelle.
wls_fieldcat-ddictxt = 'L'.
wls_fieldcat-no_out = wv_no_out.
APPEND wls_fieldcat TO gt_fieldcat.
Kind regards,
Jegathees P. -
LaserJet Pr0 200 color MFP M276nw Touch Screen not Working correctly
Hello, I'm having an issue with a LaserJet Pr0 200 color MFP M276nw Touch Screen not Working correctly. I have followed the instructions to reset the printer, but now am unable to select 'English' as my language because every time I select the 'English' option 'Spanish' is selected. I am then given two options to select 'Si' or 'No' both of which can not be selected on the touch screen?
Anybody know of a way round this?Hi @dnhowes ,
I see that you are having issues with the touch screen not working correctly. I will do my best to help you.
Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation.
Was it the Nvram reset back to factory settings that you tried or a hard reset?
Try selecting the option on the display a little higher above the icon to see if that helps. Some touch screens are finicky.
I find that on the Lab printers when I am selecting different menus.
If the issue continues, please call our technical support at 800-474-6836 for further assistance. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP -
Property inspector not working correctly
The property inspector in CS3 is not working correctly. When
I select text or any other object the property inspector does not
change for that object. But when I right mouse click on the
selected object it does. Do I need to change a setting?
Thanks!Yes, me too. I can't find an answer to this anywhere.
If I right-click or double-click on an item the property
inspector shows it, but if I single click, nothing happens. It's
bad for productivity. -
Why can I not import pictures any more?
Lightroom says "Your Lightroom 5 64-bit does not work correctly"
Technical informations:
PC with Windows 7 64-bit, Lightroom 5.7.1 64-bit installed.
What I have done:
I downloaded the newest LR 5.71 and installed it again - mode repair; without success
I checked my PC with Norton 360: full scanning and optimizing registry
I restarted the PC and than I installed the LR 5.7 again - repair
Trouble 1:
Two days ago I could work with my LR 5 and to import pictures from a SD was no problem. Now I can start LR 5 and I can watch/modify pictures, but as soon as I try to import new pictures LR 5 stops and gives the message "your LR 5 64-bit does not work correctly - searching for solution". I have not changed anything in my computer since lasttime LR 5 worked properly, only the registry was optimized by Norton 360.
Trouble 2:
I live in Switzerland and my language ist German. I dit not find a place where I can present my problem in German, e.g. a phone number oder email-address oder german-chat. My English is to week for a discussion for computer problems and do understand it.
Help:
I would very appreciate if anybody can help me, either to trouble 1 or to trouble 2. Thanks.Sehen Sie diesen Beitrag:
Photoshop CS4 & Lightroom 2.6 X64 funktionieren nicht mehr
Wacom Tablet-Treiber-Problem? -
Program not working correctly-Help!
class Sort
/* method takes an array of integers as an input,
* and returns a copy with the element values sorted
* by select method.
int[] selectSort(int[] input)
/*declare variables to be used in array */
int x, y, max, temp;
int[] select = new int[input.length];
/*This loop reads the entire array */
for(x = input.length - 1; x>0; x--)
max = 0;
/*This loop checks to see if any number is
lower possible greatest number /
for(y = 0; y <= x; y++)
{//Returns number if lowest number
if(input[y] > input[max])
max = y;
}//end of if statement
}//end of inner loop
/*Switches the values */
temp = input[x];
select[x] = input[max];
select[max] = temp;
}//end of outer loop
return select;
} //end of selectSort()
/* method takes an array of integers as an input,
* and returns a copy with the element values sorted
* by bubble method.
int[] bubbleSort(int[] input)
int[] bubble = new int[input.length];
for (int x = 1; x < input.length; x++)
for (int y = 0; y < input.length - 1; y++)
if (input[y] > input[y+1])
int temp = input[y];
bubble[y] = input[y+1];
bubble[y+1] = temp;
return bubble;
} //end of bubbleSort
**********************Test Class**********************
class TestSort
public static void main(String[] args)
/* count variable used as loop counter when
* result table display is generated
int count;
/* variable for object of class Sort */
Sort x;
/* create object of class GroupEx2 */
x = new Sort();
/* create a source array of integer elements */
int[] y = new int[5];
/* assign values to array elements to be sorted */
y[0] = 8;
y[1] = 5;
y[2] = 3;
y[3] = 9;
y[4] = 1;
/* create variable for target of select sort array */
int[] ss;
/* create variable for target bubble sort array */
int[] bs;
/* call method to return an array with element values select sorted*/
ss = x.selectSort(y);
/* call method to return an array with element values bubble sorted*/
bs = x.bubbleSort(y);
/* display original and sorted arrays in three columns*/
System.out.print("Input Array" + "\t");
System.out.print("Select Sort" + "\t");
System.out.println("Bubble Sort");
for (count = 0; count < y.length; count++)
/* Column 1: original array */
System.out.print("input[" + count + "] = " + y[count]);
/* tab between columns 1 and 2 */
System.out.print("\t");
/* Column 2: select sorted array */
System.out.print("select[" + count + "] = " + ss[count]);
/* tab between columns */
System.out.print("\t");
/* Column 3: bubble sorted array */
System.out.println("bubble[" + count + "] = " + bs[count]);
} // end of display for loop
} // end of main()
} // end of class TestSortThanks for the Bash! I'm surprised you had the time
for it.Go back and look at your original post. A whole bunch of code, and the only description of the problem is "not working correctly." Do you honestly think that's a reasonable way to ask for help? Do you go to the doctor and say, "I'm sick" and then just wait for him to cure you? Do you take your care to the mechanic and say only, "It's broke"?
Look, this is your problem and it's your responsibility to fix it. There are people here who are happy to help you, but it's up to you to provide a reasonable statement of what's wrong, what you've tried, what you don't understand. For instance:
Does it compile? If not, post the complete error message.
Does it run, but throw an exception? If so, post the stack trace.
Does it not throw an exception, but not behave the way you expect? Then describe the expected beavior and the observed behavior.
Do you really need to be told this stuff? It seems like common sense that when you're asking people to spend their time helping you, you should give them the information they need to be able to do so. -
Some time tech pad not working correctly
I am buy a HP Pavilion laptop from awok.com. Some time mouse teach pad not working correctly some time open windows 8.1 time bar and some time i am using mouse teach pad then automaticly come right click popup menu coming some time i am try to scrol the page using mouse pad then automaticly Select all from the page so please help me
Hello @BABUMON ,
Thank you for visiting the HP Support Forums and Welcome. I have read about your HP Notebook and mouse freezing. Here is a document on how to troubleshoot the mouse and Touchpad sensitivities.
If you will go to the section on Adjusting TouchPad or ClickPad pointing sensitivities it should help resolve the issue.
I would be happy to assist if needed as there are many models of HP Notebooks, I would need the model number.
How Do I Find My Model Number or Product Number?
Please respond with which Operating System you are running:
Which Windows Operating System am I running?
Please let me know.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping! -
Canon MG3550 is not working correctly
Hello,
I have recently bought Canon MG3550. I installed the driver etc but the printer is not working correctly. Sometimes it prints without any issues but other times it:
- does not pick the printer - saying it's offline even though it's not (this is from laptop, iPad, phone...not just from one device)
- does not print - the error message appears after a while saying that the printer is not responding
- prints half of the page...or just picks up a paper but doesn't print at all
I tried to de-install and re-install the driver etc. but it did not help. The printer is still behaving the same unpredictable way.
Do you have any ideas how to solve it? It is a faulty device or am I doing something wrong?
Thank youYour tags show iPad. You need the iPad 3 or newer in order to have Siri. What iPad do you have?
There are a number of apps that are compatible with Word....Documents to Go, Pages, Quick Office Pro .... You need an app that will read, save and Word files on the iPad and if you don't have such an app, all that you can do is email the file and read it in the email. You will not be able to save or edit the files.
After you download one of this apps, you can use email, DropBox, and IOS file sharing in order to transfer the documents back and forth. You can use iCloud as described above with Pages or any other app that works with iCloud.
Read this to learn more about file sharing.
http://support.apple.com/kb/HT4094
Maybe you are looking for
-
Is there a guide to iMovie 11 for someone who understands video editing in the normal way?
Yesterday, for the very first time, I used iMovie 11. My son shot a little video on his iPod Touch, and then wanted to play around with the titles and transitions a bit more than the iPod would afford. So, we did the import via iTunes dance, and op
-
I have an iphone 3 and I have lost all my downloaded ringtones and music but when I sync with itunes it will not load it back on my phone. Does anyone have any suggestions?
-
I have windows 7 64 bit but the new itunes will not install because it can't find itunes64.msi. I have searched evertwhere on my pc. In addition, I can't uninstall the itunes and reinstall for the same reason. I can't upgrade for my icloud account.
-
Connecting a SATA disk to my iMac
I had my 250GB LaCie d2 SATA disk connected to my G3 using the Serial ATA PCI card which came with the disk.It worked fine. Recently I replaced the G3 by an iMac; it has no SATA connection and no room to add the Serial ATA PCI card. However, I also b
-
Check SQL 2008 standard or enterprise
Hi, how can I check sql 2008 edition except running query on sql browser? Or can I check this information from registry?