Cucme and cucm with aim-cue

Hi all, I just want to know if AIM-CUE can work with cucme and cucm 8.0?
Because based on this matrix Cisco Unity Express Compatibility Matrix [Cisco Unity Express] - Cisco Systems
It says that it is supported, but CUE (AIM-CUE Module) should have a version of 7.2 or 7.3 to support cucme 8.x and cucm 8.x
Can anyone confirm this because aim-cue is the cheapest among the CUE cisco offers. Thanks!

That's what I read, having cue 7.2 or 7.3 will let you use cucme/cucm 8.x
When you say "there will not be any new firmware release on the old aim-cue", Does that mean that cue version 7.3 will be the last firmware version to be released on the old aim-cue that will support cucme/cucm 8.x? Future versions of cucme/cucm (version 9) will not be supported by the old aim-cue?

Similar Messages

  • Itunes and Conflicts with AIM

    *Notes: I have itunes 7.0 and an old version of AIM (because I absolutely hate the new, ad covered version - Triton, or whatever it's called)
    I was listening to itunes with AIM open and running, and everything was fine. The moment someone IMed me, my song went to double time, twice as fast as normal and very scratchy. I tested a few different songs, and they all had this problem. I read this article: http://docs.info.apple.com/article.html?artnum=93610h and assumed maybe the issue has to do with "direct sound" output (last paragraph on that page). When I closed AIM, itunes went back to normal. (this is the first time I've used the two programs at the same time since upgrading to the new version of itunes.
    I'd like to know if there's anything I can do. It seems silly to me that since I upgraded itunes I apparently can never use it at the same time as aim. This is the 21st century, after all! Do you guys have any suggestions that don't involve upgrading to a newer, more annoying, version of aim? Thanks!

    I think I figured it out...get an app on any device linked to iCloud and it appears on all of them. It just works!

  • 2821 with AIM-CUE card echoing prompt and command entered

    Is there any way to control the prompt on AIM cards? I have a command reference for 3.0 and above, but the normal config commands like "prompt ..." don't exist.
    The problem this device presents is that it does not output a clean text-based prompt, such as "CUE-48101# " in response to a command or carriage return. Instead it appears to output the following:
    <cr><esc>[0;1mCUE-48101<bs>1#<bs># <bs>
    Here, <bs> is backspace, <esc> is the escape character, <cr> is the carriage return. Visually it seems fine to a user at the terminal, but for a program it's a nightmare. In addition, the device is echoing both the prompt and the command issued, so my ability to know when the output has stopped is compromised.
    My understanding is that there's a Linux kernel underneath, that implements the IOS-like command syntax from the user, but I don't know how to disable this ridiculous painting of the screen. Any insights you can provide are greatly appreciated.

    Which port are you using? Should be base 2000 + tty.

  • AIM-CUE Re-Initialize? Or Security Check...

    Good afternoon all,
    Have a 2801 with AIM-CUE that I cannot login to the GUI. I went through the initialization wizard from CLI with no trouble, but it would not complete on the GUI side after I logged in the first time and ran the initializtion wizard. It did not complete and I was going to back out and come back to it after checking settings.
    Now I am not getting the Initialization wizard and it is telling me Lost Contact after I am able to login. When I try to enter the Hostname, Username and Password, it is saying it failed to connect.
    Is there a way to re-initialize the wizard or is there something I am missing in my security on these?
    I can include portions of the configs from the router and the AIM module if it helps. I can still work with the AIM side via CLI, but even adding another Admin account and changing everything is not letting me access it (not as a first resort...)
    I'm not finding a clear path to follow after this and when I look at the configs it all appears to be correct and matches my last install (2811 with AIM).
    Thanks,
    Jon Gauntt

    I just did that. Although all the links to the 3.X.X files were all showing Network Unavailable.
    I downloaded a 2.3.4 and got the initialization wizard to run. And it looks like I have some kind of configuration issue in my telephony service or am missing a file in my flash (even though I have now loaded extra files i do not need that I will need to take back off).
    Here is my Telephony-Service:
    telephony-service
    load 7960-7940 P0030702T023
    load 7902 CP7902080001SCCP051117A
    load 7931 SCCP31.8-2-2SR1S
    load 7970 SCCP70.8-2-2SR1S
    max-ephones 30
    max-dn 108
    ip source-address 10.10.82.1 port 2000
    calling-number initiator
    url services http://10.10.82.5/voiceview/common/login.do
    url authentication http://10.10.82.5/voiceview/authentication/authenticate.do
    time-zone 8
    bulk-speed-dial list 2 flash:localdirectory.txt
    bulk-speed-dial list 6 flash:corporatedirectory.txt
    voicemail 7000
    max-conferences 8 gain -6
    call-forward pattern .T
    moh 122007.au
    web admin system name admin password cisco
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 9.T
    secondary-dialtone 9
    after-hours block pattern 1 1900....... 7-24
    night-service code *777
    night-service day Sun 00:00 23:59
    night-service day Mon 18:00 06:00
    night-service day Tue 18:00 06:00
    night-service day Wed 18:00 06:00
    night-service day Thu 18:00 06:00
    night-service day Fri 18:00 06:00
    night-service day Sat 12:00 08:00
    create cnf-files version-stamp 7960 Nov 27 2007 16:42:32
    I am attaching a list of the files on the flash.
    If anyone sees anything obviously missing, it would be helpful. I am using a config that I have up and running in a 2811 for this 2801 and there might be a slight difference I am not accounting for.
    Thanks,
    Jon Gauntt

  • Why can't I use screen sharing with AIM using Mountain Lion?

    Hi everyone: I am 100% sure that my friend and I both have active, valid AIM supported user names and can exchange messages but CANNOT video chat or share screens as befo rewith iChat. Anyone know what the issue may be? Am I alone or is this a known issue with a fix? Bot of us are running Mountain Lion using iMessage prgram but are online and "Available: with AIM.
    Thanks,

    Hi, I'm not often on AIM/iChat, but do you care to share your screenname & setup a time to try it?
    If you don't wish to show your eMail to others in your profile, you can contact me by joining my site...
    http://x704.net/bbs

  • Can't video chat with AIM only .mac users like me.

    Hi,
    I'm running the latest iChat AV.
    There seems to be alot of posts regarding people being unable to chat with .mac and only AIm but my problem is exactly the opposite. I can only video chat with other .mac users and not with AIM users. (I am .mac).
    Nothing here involves a PC, all accounts are on macs. Any .mac friends I try and video chat to it works great, but any mac AIM users all I kept getting are 'failed to respond' messages. I failed to respond or they did depending on who initiated the video chat. All type chatting works fine. I have no firewalls and plenty of bandwith. To the best of my knowledge the AIM users have no firewalls either. Any ideas?
    Thanks.

    Hi Rodi,
    There has been one report of a .mac user contacting .mac because of this problem. He said he was informed that they were aware of the problem exsiting for some users but that they could not tell which ones.
    They did something to his account that made it work (some problem with the .mac user list and the AIM Servers)
    I suggest you explore this as well.
    Ralph

  • Integration CUCM with MCU Cluster, TCS and TMS

    Hi all,
    Do you have any guides, information and suggestions about integrating CUCM with MCU, TCS and TMS?
    To centralized IPT and Video Conference enviroment, i need to register MCU and TCS to CUCM v10.5.
    Also TMS should provision devices which are register to CUCM.
    Best Regards,
    Mesut

    Hi Mesut,
    You can refer below support forum links:
    https://supportforums.cisco.com/discussion/11281276/cucm-cts-and-tms-integration
    https://supportforums.cisco.com/discussion/11587226/registering-mcu-cucm-86
    Regards
    Sumeet

  • AIM-CUE and CCME

    Good day, we have a new CCME 3845 Router including VIC2-4FXO,NM-HD-2V,EVM-HD-8FXS/DID,EM-HDA-6FXO modules, this will be used for our new project. Is it possible that the CCME Router will work well on IP Phones even without the AIM-CUE, because that is the only remaining device that need to install on the Router and we want to install now the Router at the Site while we are waiting for the AIM-CUE to arrive the IP Phones should work. Thanks and I will wait for your reply.

    Hi Mahmoud,
    You should be fine to get started without the AIM-CUE. This will only prevent the setup of the Voicemail potion of the install :)
    Cisco CallManager Express/Cisco Unity Express Configuration Example
    http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a008037f2a9.shtml
    Cisco CallManager Express 3.0 and Later Integration with Cisco Unity Express
    http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a008059fb5f.html
    Hope this helps!
    Rob

  • Is there a way to Configure "Silent Monitoring" in CUCM with the following conditions: ?

    Is there a way to Configure "Silent Monitoring" in CUCM with the following conditions: ?
    -no UCCX platform
    -cisco phone is CP-6941.
    I have read some cisco docs pertaining to Barge and cBarge, however i see that as one-to-one arrangement.
    Is there a way to configure in cucm, something like an ad-hoc conference wherein the Observer will
    just call the extension number to be observed?
    or something like "service observed" feature in Avaya wherein the Observer will dial a particular
    passcode followed by the extension # of the agent, then he is able to observe the on-going call.

    You can do continous recording using SPAN ports or DMS with 3rd party products like Verint Impact 360.
    not sure about the legalities around that though.
    =============================
    Please remember to rate useful posts, by clicking on the stars below.
    =============================

  • Trouble with AIM and IChat! Cannot connect to IChat, and AIM keeps crashing

    I just got my Macbook, and installed AIM. However, it often says "AIM shut down unexpectedly." Does anyone know how to fix this problem?
    Also, I want to use IChat, but i try to connect, and I can for a few seconds, and then it says "Connection with AIM lost." I'd appreciate any suggestions or advice!

    I used to have the same AIM problem. Have you tried Adium instead? If you haven't heard of it, it's an instant messaging program that uses your AIM account but is specifically designed for OS X. It looks nicer too.
    Hope it helps!
    www.adiumx.com/

  • 1760V router and AIM-CUE

    Does anyone know if the AIM-CUE will work in a 1760 or 1760V router?  I know it is not on the compability list but I know sometimes things work where not listed.

    Michael,
    Sorry but the 1760 range are not in the AIM-CUE compatability matrix.
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html#HardwareAIM
    Regards,
    Alex.
    Please rate useful posts.

  • AIM-CUE

    Can l connect the AIM-CUE which is inside the 2801 with CUCM the same way that l will connect to the CME. I have a computer which l dedicate for my callmanager 8.0 and l have cisco 2801 which l want to install the AIM-CUE into for my viocemail. The configuration that l have is for the CME, l need the setup for the CUCM for the AIM-CUE for the 2801 which l want to setup. Any advice from someone pls.

    Hi there,
    Can you please review the steps in this excellent doc;
    CallManager for Cisco Unity Express Configuration Example
    http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a0080289ef0.shtml
    Cheers!
    Rob

  • AIM/CUE not Picking-up in-bound external calls

    I have a 2811 router with an AIM/CUE (12-VM) card. All of the telephony-service stuff works fine:
    -All calls in house work fine
    -All outbound calls work fine, to PSTN
    -All inbound calls work fine, from PSTN
    -Each phone can access it's VM internally
    -the CME gui and the Unity-Express gui's are accessible on the LAN.
    But, when I call from outside into the PRI with a DID number, I get four rings, then a pause, and then it never goes to voicemail. Sometimes; depending if I call with my celr or a land line, I get the message "Sorry your call cannot be completed as dialed, 000-000." Any clue why the vm does work for internal or external calls.
    Here's a sample of the config.
    interface FastEthernet0/0
    no ip address
    no ip mroute-cache
    duplex full
    speed 100
    interface FastEthernet0/0.100
    description SUB-IF for VOICE VLAN
    encapsulation dot1Q 100
    ip address 10.1.100.1 255.255.255.0
    interface FastEthernet0/0.101
    description GW FOR VOICEMAIL MODULE AIM/CUE
    encapsulation dot1Q 101
    ip address 10.1.101.1 255.255.255.0
    interface Service-Engine0/1
    discription AIM/CUE VOICEMAIL MODULE
    ip unnumbered FastEthernet0/0.101
    service-module ip address 10.1.101.2 255.255.255.0
    service-module ip default-gateway 10.1.101.1
    ip route 10.1.101.2 255.255.255.255 Service-Engin0/1
    dial-peer voice 40 voip
    description ** cue voicemail pilot **
    destination-pattern 6000
    session protocol sipv2
    session target ipv4:10.1.101.2
    dtmf-relay sip-notify
    codec g711ulaw
    no vad
    dial-peer voice 41 voip
    description ** cue auto attendant **
    destination-pattern 6001
    session protocol sipv2
    session target ipv4:10.1.101.2
    dtmf-relay sip-notify
    codec g711ulaw
    no vad
    dial-peer voice 1 pots
    description ** T1 PRI Emergency 911 **
    destination-pattern 9911
    port 0/0/0:23
    forward-digits 3
    dial-peer voice 2 pots
    description ** T1 PRI OutBnd Calls **
    destination-pattern 9T
    port 0/0/0:23
    dial-peer voice 3 pots
    description ** T1 PRI InBnd Calls**
    incoming called-number .
    direct-inward-dial
    port 0/0/0:23

    Problem has to do with how many Digits are getting sent to voice mail on the router when it tries to make the call. You should be seeing 10 digits in the debug.
    Next question when one ephone calls another ephone locally does voice mail work?
    Try the following commands. This will create a translation-rule that will strip incoming 10 digits to the 4 digits you need. I assume you do not need all 10 digits.
    voice translation-rule 1
    rule 1 /^650\(....\)/ /\1/
    voice translation-profile digitstrip
    translate called 1
    voice-port 0/0/0:23
    translation-profile incoming digitstrip
    *************Voice port were you Telco Line comes in Port 0/0/0:23 based on your config*************
    telephony-service
    no dialplan-pattern 1 6503926... extension-length 4
    Ronnie

  • Adding phones and users with bat and LDAP sync

    What are the various ways of importing users with phones when the Communications Manager 9.0 is sync'd with LDAP.  Also, what method is the easiest and fastest?
    For example, I could do the following steps:
    Sync CUCM with LDAP to import new users, add phones using bat files, manually update users to associate devices etc
    I believe I should also be able to do the above method and use a bat file to update the users to associate devices etc.  This method still involves 2 steps and the creation of 2 seperate bat files.
    In CUCM version 9 it is possible to have local and LDAP users, so is it possible to add the phones and users using the phones/users tab of the bat file and have them beocme LDAP users?
    Thank you,
    Danny

    #1 Remove this embedded CSS code from your HTML document(s).  You don't need it.
    body {
        background-color: #CCC;
    body,td,th {
        color: #FFF;
        font-size: 14px;
    #2 Open  PW.css file and add this to the top:
    body {
    font-family: Arial, Helvetica, sans-serif;
    font-size: 14px;
    background-color: #CADFEB;
    /**or insert a background-image using the CSS editor**/
    #3 Remove font-family and font-size from all your other CSS selectors.  You don't need to duplicate styles on every element. 
    #4 Replace this:
    #content {
        position:absolute;
        left:199px;
        top:10px;
        width:860px;
        z-index:1;
        right: auto;
        background-color: #FFF;
        text-align: center;
        color: #000;
        height: auto;
    with this:
    #content {
         width:860px;
         margin: 20px auto;
         border: 4px solid silver;
         background-color: #FFF;
         text-align: center;
         color: #000;
         -moz-box-shadow: 5px 5px 5px #888;
         -webkit-box-shadow: 5px 5px 5px #888;
         box-shadow: 5px 5px 5px #888;
    #5 Save your PW.css file and upload to server.
    Nancy O.
    Alt-Web Design & Publishing
    Web | Graphics | Print | Media  Specialists 
    http://alt-web.com/
    http://twitter.com/altweb

  • AIM-CUE module

    Hi
    I have installed an AIM-CUE into my 2801 router, but there are some files which am not sure which will work with this AIM-CUE which l have installed into the router 2801. These are files that l have and l need an advise concerning these files because l have the nme and the aim files but the device that l have installed into my router 2801 is AIM-CUE. Advice me on which ones to use pls.
    Ojay
    1 cue-installer.nme.7.0.3
    2 cue-vm-installer-k9.nme.7.0.3.prt1
    3 cue-vm-k9.nme.7.0.3pkg
    4 cue-vm-licence_50mbx_ccm_7.0.3pkg
    5 cue-vm-en_US-langpack.nme.7.0.3prt1
    6 cue-vm-full-k9.nme.7.0.3.prt1
    7 cue-vm-langpack.nme.7.0.3.pkg
    8 cue-installer.nm-aim.7.0.3

    Hi Ojay,
    Here we go
    For NM-CUE, NM-CUE-EC, and AIM-CUE (cue-vm-k9.nm-aim.7.0.x.zip)
    •cue-installer.nm-aim.7.0.x
    •cue-vm-k9.nm-aim.7.0.x.pkg
    •cue-vm-full-k9.nm-aim.7.0.x.prt1
    •cue-vm-installer-k9.nm-aim.7.0.x.prt1
    •cue-vm-langpack.nm-aim.7.0.x.pkg
    http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel7_0/install/boothelp.html#wp1142398
    And;
    cue-vm-en_US-langpack.nm-aim.7.0.6.prt1
    Release Date: 05/OCT/2010
    Package payload containing all US English language data and prompt files associated with the Cisco Unity Express with VoiceMail application on the AIM-CUE, NM-CUE, and NM-CUE-EC service modules.
    Size: 27537.68 KB (28198577 bytes)
    Cheers!
    Rob
    Please remember to tag your threads and help support "Teachers without Borders"
    https://supportforums.cisco.com/community/netpro/idea-center/communityhelpingcommunity

Maybe you are looking for