CUE "Service Module is failed"

Dears , i am getting this error on CUE .I reload the router but result is same .what should i do now?? ..
#service-module service-engine 0/1 status
Service Module is Cisco Service-Engine0/1
Service Module supports session via TTY line 258
Service Module is failed
Service Module status is not available
Regards,
Shib

You've powered off and re-seated the card and this was working at one point? Beyond that, if there is no output from the CUE console (while connected to the module via "service-module service-engine 0/1 session"), then the module is likely defective.

Similar Messages

Service Module is failed

when i show service-module ids-sensor 1/0 status
i have the following output
Service Module is Cisco IDS-Sensor1/0
Service Module supports session via TTY
Service Module is failed
Service Module status is not available
what is the problem and how can i recover it?
note i make restart for the service module by the command
service-module ids-snsor 1/0 reset
but it remain failed
please help me as soon as possible

You've powered off and re-seated the card and this was working at one point? Beyond that, if there is no output from the CUE console (while connected to the module via "service-module service-engine 0/1 session"), then the module is likely defective.

What if two service modules fail on a MDS 9513?

Hello,
We recently had a service module failure on one of our core MDS 9513 directors.
It is fixed now but I was wondering what would happen if the second service module had failed as well a bit later...
Will the director still function? All line cards and crossbars are still functionning. But there will be no management possible etc...
Will the traffic continue?
Kind regards,
Ivy

Ivy
The director would then fail completely.
Though I don't know anyone that unlucky

Service Module is trying to recover from error - Please help

HI Guys
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status
I have checked the troubleshooting pdf and says might be possible hardware error ,but before i go down that road would like to know if any of the engineers have solved this problem
Info about router and module is as follows
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is trying to recover from error
Service Module status is not available
Router#
Trying to reset Service Module wlan-controller1/0
*Mar 28 21:49:06.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface wlan-controller1/0, changed state to down
*Mar 28 21:49:26.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface wlan-controller1/0, changed state to up
Router#
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is trying to recover from reset/shutdown
Service Module status is not available
sh version
Router#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T17, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 24-Jan-12 07:41 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
Router uptime is 28 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-advipservicesk9-mz.124-15.T17.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FCZ0932701R
2 FastEthernet interfaces
1 Serial(sync/async) interface
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Wireless LAN Controller(s)
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router#

HI Guys
And it gets worse I am now getting the following error
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is failed
Service Module status is not available
regards Thags Govender

Service-module g2/0 session access fails

I did not add a vty/telnet password when I initially configured my NME-X-23ES-1G switch in my 3825 router. Now, of course I can not telnet to the switch, but the session access fails as well. How do I recover this?
Config in 3825:
interface GigabitEthernet2/0
ip address 106.40.x.x.255.255.0
Attempt to access switch module:
3825_Router2#service-module g2/0 sess
Trying 106.40.77.254, 2130 ...
% Connection refused by remote host

The default configuration for Cisco EtherSwitch service modules allows an end user to recover from a lost password. The password recovery disable feature allows the system administrator to protect access to the switch password by disabling part of this functionality and allowing the user to interrupt the boot process only by agreeing to set the system back to the default configuration. With password recovery disabled, the user can still interrupt the boot process and change the password, but the configuration file (config.text) and the VLAN database file (vlan.dat) are deleted.
The following document shows how to recover from a lost or forgotten password.
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_feature_guide09186a0080415bae.html#wp1776357

Cisco 3560 service module failed state

Hi Expert,
My office has a Cisco 2911 ISR router, we installed a 3560 service module 16P on it.
But I use command "sh ip int bri" in 2911 router when we finished installation.
The result shows that the interface Gi 1/1 doesn't work, I have try to re-install SM 16P twice, the result is the same.
The normal 2911 ISR + 3560 SM 16P show as below,
2911#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administrativelwy down down
GigabitEthernet0/0 xxx.xxx.xxx.xxx YES manual up up
GigabitEthernet0/1 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet0/2 unassigned YES NVRAM down down
GigabitEthernet1/0 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet1/1 unassigned YES unset up up
The BAD 2911 ISR + 3560 SM 16P show as below,
2911#sh ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
GigabitEthernet0/2 unassigned YES NVRAM administratively down down
GigabitEthernet1/0 unassigned YES NVRAM administratively down down

Hi Krishnendu,
I understand what you mean, I have done this work for assign Gi 1/0 an IP address, and then using command "service-module gi 1/0 session" to enter the service-module to configure it at all.
But I just want to know what is the Gi1/1 interface used for?
I use command "sh cdp nei" on others 2911 ISR + 3560 service module, all of the has the Gi 1/1 interface, and 2911 router using Gi 1/1 interface connected service module Gi 0/17. And Gi 1/1, Gi 0/17 is configured with "trunk interface".
I'm wondering whether my 2911 router Gi 1/1 has some physics error? or maybe it has another command to to "OPEN" the Gi 1/1 on 2911?
The "normal" switch display as below,
rtr001#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
swt000.nneas.net
Gig 1/0 129 R S I SM-ES3G-1 Gig 0/18
swt000.nneas.net
Gig 1/1 129 R S I SM-ES3G-1 Gig 0/17
Thanks in advance,
BR Frank

ITunes - Ipod Service Module

I purchased songs from ITunes and it has charged my account, yet when I go do download them on to my IPod I get and error message saying: IPOD SERVICE MODULE HAS ENCOUNTERED A PROBLEM AND MUST CLOSE, so I can't download. Has anyone else run in to this problem after installing Service Pack 3 on Windows XP. Sure would like some help. Microsoft had me do a couple of things that didn't seem to help.
CR

I tried reinstalling iTunes and keep getting the same iPod Service Module Error. I also tried running the iPod Software Updater and I get a message that I have an invalid iPod Service version.
I recently tried u[dating Windows XP with the Service Pack 3 updates. I cannot get this to complete the install. I get a message stating that the updates failed and Windows XP may not work properly. I wonder if this is causing my headaches? my iPod seemed to work fine before I tried this SP3 update.

XML Publisher with Service Module - Service Request Reports -- URGENT

Hi all ... any pointers/help/guidance with the problem listed below would be much appreciated.
I'm working in the context of the Oracle Service Module & Service Request Reports.
I'm required to configure the XML Publisher Responsibility seeded functionality with the service module reports.
Listed below are the two reporting requirements that I'm considering , corresponding to the following seeded XMLP Responsibility seeded components:
(I'm quoting an extract from the Oracle TeleService Implementation & User Guide here).
Detailed Report
Data Definition: Service Request Detail Definition (CS_SR_DETAIL_DEF)
Corresponding Template: Service Request Detail Report Template (CS_SR_DETAIL_TMP.en)
Template Description: Includes all of the available service request attributes including charges, the two descriptive flexfields, and extensible attributes.
Summary Report
Data Definition: Service Request Summary Definition (CS_SR_SUMMARY_DEF)
Corresponding Template: Service Request Summary Report Template (CS_SR_SUMMARY_TMP_en)
Template Description: Includes a subset of the detailed report attributes including the same charges information as the detailed report.
When I log into the EBS >> XML Publisher Administrator Responsibility >> Service Application ... I find these seeded XMLP components, together with the preview data, downloadable templates & sample output.
The question is:
Where (responsibility/application/navigation/etc.) do I find the seeded EBS Service Reports to provide the expected XML input to the seeded XMLP Service Request Data Definitions & Templates????
Notes ...
I have found the following two reports, under the Service Application in EBS, set their output type to XML and viewed the output of the submitted request:
- Service Request Detail Report
- Service Request Summary Report
... but each of these two reports produce XML output of a different data model/structure to that expected by each of the corresponding seeded XMLP data-definitions/templates.
Additionally, I cannot find any corresponding concurrent program definitions on the system with the same SHORT-NAME/CODE as the seeded XMLP data definitions themselves i.e. CS_SR_DETAIL_DEF and CS_SR_SUMMARY_DEF.
Are the necessary reports not actually seeded within EBS? Do the seeded XMLP data definitions & templates require development of new Concurrent Programs from scratch to access the database tables and provide the necessary data/input, or am I missing something here??

I am sure you found a solution to your problem. If not, to give a pointer to this issue, I guess these reports are gererated right from the service request screen and this definition is used there.This report can be generated from several places based on where you are within SR scree.
Thanks
Nagamohan

SM:EXEC SERVICES job getting failed in Solution manager

HI All,
SM:EXEC SERVICES job getting failed in solution mnager and job log will be fowlloing:
01-31-2012 19:09:21 Job started
01-31-2012 19:09:21 Step 001 started (program RDSMOPBACK_AUTOSESSIONS_ALL, variant , user ID BASISUSER)
01-31-2012 19:09:21 MemSize Begin = 796480 Bytes
01-31-2012 19:09:21 *******************************
01-31-2012 19:09:21 MemSize Begin = 1919120 Bytes
01-31-2012 19:09:23 Solution <000000106120000> "SID..." is being edited (Operations)
01-31-2012 19:09:23 <000000106120000> "SID..."(Operations)
01-31-2012 19:09:23 "Create_Periodic_Services" uses = 0 bytes
01-31-2012 19:09:23 "Create_Periodic_Services" uses = 690 us time
01-31-2012 19:09:23 Trying to perform session EC2000000001313
01-31-2012 19:09:24 MODEL_KEY: SID Installation Number: 6 MODEL_MODE: E MODEL_VERSNR 00001 MODEL_CLASS: EWA Data Model
01-31-2012 19:09:30 Definition nicht vorhanden
01-31-2012 19:09:33 Definition nicht vorhanden
01-31-2012 19:09:45 Internal session terminated with a runtime error (see ST22)
01-31-2012 19:09:45 Job cancelled
St22 Dump:
The exception 'CX_DSVAS_API_CONTEXT_INSTANCE' was raised, but it was not caught
anywhere along
the call hierarchy.
Since exceptions represent error situations and this error was not
adequately responded to, the running ABAP program 'SAPLDSVAS_PROC' has to be
terminated.
Please suggest how to proceed further and provide your valuble inputs
Thanks
Nekkalapu

HI Siva,
I have done the changes according the note but still same problem.
Please suggest any other ways to resolve this issue .
Advance thanks
Regards
Nekkalapu

How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module

hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
                                                  ^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2921/K9          FGL1618119E
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            None          None           None
data          None          None           None
Configuration register is 0x2102
R2921-8CPITR-1#

Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end

While applying patch 3653484, Relink of module "ar60desb" fails

Hi All,
While applying patch 3653484, Relink of module "ar60desb" fails
adrelink.log file entry
Starting link of fnd executable 'ar60desb' on Wed Apr 29 10:52:39 PAKDT 2009
ld -s -H512 -T512 -bhalt:4 -brtl -L/erpbkp/oracle/tstora/8.0.6/lib
-L/usr/lib -o /erpbkp/oracle/tstappl/fnd/11.5.0/bin/ar60desb.new
/erpbkp/oracle/tstora/8.0.6/lib//s0main60.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/sslmdgtab.o
/erpbkp/oracle/tstappl/fnd/11.5.0/lib/xitsrw.o
/erpbkp/oracle/tstappl/po/11.5.0/lib/xirpo.o
/erpbkp/oracle/tstappl/po/11.5.0/lib/libpo.a
/erpbkp/oracle/tstappl/fa/11.5.0/lib/xirfa.o
/erpbkp/oracle/tstappl/fa/11.5.0/lib/libfa.a
/erpbkp/oracle/tstappl/ar/11.5.0/lib/xirar.o
/erpbkp/oracle/tstappl/ar/11.5.0/lib/libar.a
/erpbkp/oracle/tstappl/ff/11.5.0/lib/xirff.o
/erpbkp/oracle/tstappl/ff/11.5.0/lib/libff.a
/erpbkp/oracle/tstappl/fnd/11.5.0/lib/xirfnd.o
/erpbkp/oracle/tstappl/fnd/11.5.0/lib/fdxsrw.o
/erpbkp/oracle/tstappl/fnd/11.5.0/lib/libfnd.a
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwecat.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwecpf.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwecty.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rweats.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwepls.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rxdsql.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rweiap0.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rxsi.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/ui10.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/uiicxd.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwsng.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwscl.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwssc.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwssc0.o
/erpbkp/oracle/tstora/8.0.6/reports60/lib/rwsdt.o -lrw60 -lgraphics60
-lobx60 -lge60 -locl60 -lnn60 -lrws60 -lde60 -lzrc60 -lrws60 -lnvu60
-lnvc60 -lnvs60 -lucol60 -luicc60 -lca60 -lmmiw60 -lmmov60 -lmma60
-lmmos60 -lmmoi60 -lmmia60 -lmmft60 -lmmcm60 -lvgs60 -luihx60 -luc60
-luipr60 -luimotif60 -lot60 -lrem60 -lree60 -lrec60 -luiimg60 -luimotif60
-luipr60 -luiimg60 -luc60 -lrem60 -luimotif60 -luia60 -ltknqap60 -luipr60
-luimotif60 -lutt60 -lix60 -lixd60 -lrod60 -lror60 -lros60 -lrod60 -lror60
-lros60 -lrod60 -luat
60 -lutc60 -lutl60 -lutsl60 -lplsf -lplsb -lextp
/erpbkp/oracle/tstora/8.0.6/lib/libpsd.a -lplsf -lplsb -lextp
/erpbkp/oracle/tstora/8.0.6/lib//libslax.a -lsql
/erpbkp/oracle/tstora/8.0.6/lib/nautab.o
/erpbkp/oracle/tstora/8.0.6/lib/naeet.o
/erpbkp/oracle/tstora/8.0.6/lib/naect.o
/erpbkp/oracle/tstora/8.0.6/lib/naedhs.o `cat
/erpbkp/oracle/tstora/8.0.6/lib/naldflgs` -lnetv2 -lnttcp -lnetwork -lncr
-lnetv2 -lnttcp -lnetwork -lclient -lvsn -lcommon -lgeneric -lmm -lnlsrtl3
-lcore4 -lnlsrtl3 -lcore4 -lnlsrtl3 -lnetv2 -lnttcp -lnetwork -lncr -lnetv2
-lnttcp -lnetwork -lclient -lvsn -lcommon -lgeneric -lepc -lnlsrtl3 -lcore4
-lnlsrtl3 -lcore4 -lnlsrtl3 -lclient -lvsn -lcommon -lgeneric -lnlsrtl3
-lcore4 -lnlsrtl3 -lcore4 -lnlsrtl3 -lld -lm `cat
/erpbkp/oracle/tstora/8.0.6/lib/sysliblist` -lm
/erpbkp/oracle/tstora/8.0.6/rdbms/lib/kpudfo.o -lpthreads
-L/erpbkp/oracle/tstora/8.0.6/network/jre11/lib/aix/native_threads -ljava
-L/usr/lpp/X11/lib/R5 -lXm -lXt -lX11 -lm -lix60 -lixd60 -lX11 -lnlsrtl3
ld: 0706-010 The binder was killed by a signal: Killed
Check for binder messages or use local problem reporting procedures.
make: The error code from the last command is 254.
Stop.
Done with link of fnd executable 'ar60desb' on Wed Apr 29 10:52:39 PAKDT 2009
Relink of module "ar60desb" failed.
See error messages above (also recorded in log file) for possible
reasons for the failure. Also, please check that the Unix userid
running adrelink has read, write, and execute permissions
on the directory /erpbkp/oracle/tstappl/fnd/11.5.0/bin,
and that there is sufficient space remaining on the disk partition
containing your Oracle Applications installation.
Also, relinking modules ar60run, ar60runb, f60webmx, GLAMAS, GLAVAL, GLBAAC, GLBAAR, GLIDEL, GLIGEN, GLIXFR, GLLDEL, GLLEZL fails
Please suggest
Regards,
SK

Hi Hussein,
i was able to get rid of the relink error, as mentioned above
0706-010 Binder killed by signal Signal, was running out of some memory while linking object files...
continued with adpatch but facing
Failed: file FNDLOADSO on worker 1
worker log file entry:
Start time for file is: Wed Apr 29 2009 21:35:25
/erpbkp/oracle/tstappl/fnd/11.5.0/bin/FNDLOADSO &ui_apps UPLOAD &fullpath_fnd_patch/115/import_fndobjt.lct &fullpath_imc_patch/115/import/US_imc115ts.ldt
Uploading from the data file /erpbkp/oracle/tstappl/imc/11.5.0/patch/115/import/US/imc115ts.ldt
Altering database NLS_LANGUAGE environment to AMERICAN
Dumping from LCT/LDT files (/erpbkp/oracle/tstappl/fnd/11.5.0/patch/115/import/fndobjt.lct(115.5), /erpbkp/oracle/tstappl/imc/11.5.0/patch/115/import/US/imc115ts.ldt) to staging tables
Dumping LCT file /erpbkp/oracle/tstappl/fnd/11.5.0/patch/115/import/fndobjt.lct(115.5) into FND_SEED_STAGE_CONFIG
A database error occurred:
ORA-25153: Temporary Tablespace is Empty
The error occurred while executing the following statement:
INSERT INTO FND_SEED_STAGE_CONFIG (LCT_FILE, CONFIG_ID, ENTITY_NAME, STMT_TYPE, UPLOAD_STMT,GET_WHO_STMT, BIND_VAR_CNT, PK_VAR_CNT, ENTITY_METADATA, PROC_ID ,BIND_VAR0 ,BIND_VAR1 ,BIND_VAR2 ,BIND_VAR3 ,BIND_VAR4 ,BIND_VAR5 ,BIND_VAR6 ,BIND_VAR7 ,BIND_VAR8 ,BIND_VAR9 ,BIND_VAR10 ,BIND_VAR11 ,BIND_VAR12) VALUES( :lct_file, FND_SEED_STAGE_CONFIG_S.NextVal, :entity_name, :stmt_type, :upload_stmt, :get_who_stmt, :bind_var_cnt, :pk_var_cnt, :entity_metadata, :proc_id ,:bind_var0 ,:bind_var1 ,:bind_var2 ,:bind_var3 ,:bind_var4 ,:bind_var5 ,:bind_var6 ,:bind_var7 ,:bind_var8 ,:bind_var9 ,:bind_var10 ,:bind_var11 ,:bind_var12) RETURNING CONFIG_ID INTO :config_id
AD Worker error:
The above program failed with error code 1.
See the AD Worker log file and/or the program log file for details.
Time when worker failed: Wed Apr 29 2009 21:35:25
Evaluating symbolic arguments ....
Done evaluating symbolic arguments.
Could you please suggest?
Regards,
Krishnaraj

Web Service over SSL failing in BEA Workshop

I have deployed a web service on weblogic 9.2
I have enabled one-way ssl on it. got a trial ssl certificate from verisign. installed them on the keystore/truststore on the server as well as the jre (cacerts and jssecacerts truststores) being used by the client. the client is on different machine than the server.
i have developed the service through 'bea weblogic workshop 9.2' now when i try to test the service through the 'web services explorer' within bea weblogic workshop i receive the following error:
IWAB0135E An unexpected error has occurred.
IOException
sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
on server:
<Jul 13, 2009 6:45:44 PM EDT> <Warning> <Security> <BEA-090485> <CERTIFICATE_UNKNOWN alert was received from yunus.l1id.local - 10.10.2.72. The peer has an unspecified issue with the certificate. SSL debug tracing should be enabled on the peer to determine what the issue is.>
if i try to access the web service (over ssl) through the browser (ie/firefox), it works fine. i have generated a proxy class to access this web service through the same bea workshop and that works fine too. certificates are identified and all. i also created a small .net (c#) application that calls this secure web service over ssl from another machine and it works fine too!
of course non-secure url for the web service is working fine in every case.
what can be the reason for this failing only in 'web services explorer' in bea workshop?
cross posted at: http://www.coderanch.com/t/453879/Web-Services/java/Web-Service-over-SSL-failing
thanks.

Hello,
I used this example, when I made my experiments with SSL and Glassfish (GF):
http://java.sun.com/developer/EJTechTips/2006/tt0527.html#1
If you have problems with GF I suggest to post a message here:
http://forums.java.net/jive/forum.jspa?forumID=56
e.g. here is one thread:
http://forums.java.net/jive/thread.jspa?threadID=59993&tstart=0
Miro.

Windows could not start the FLEXnet Licensing Service service on Local Computer Error 1068: The dependency service or group failed to start.

Today I installed Adobe Director 11.5. I received a couple of errors in the FLEXnet Licensing Service. It looks It could not start. I tried to download the Licence fix what I found on Google but that doesn't work, so I checked the 'Service' at service (windows).
It's status is empty. When I double click on the FLEXnet Licensing Service, clicked on start at the opened window and an error is coming:
Windows could not start the FLEXnet Licensing Service service on Local Computer
Error 1068: The dependency service or group failed to start.
I don't understand what it says with this message, only that it is impossible to start. However, that is not what I am trying of course, I want to start the FLEXnet Licensing Service, service.
Re-installing of the software, doesn't make any change. How can I start it so Director is also working?

Hi Don1233,
Please consider seek help at the software vendor side.
For the services didn't start, follow the suggestions posted by Elton in the thread below:
https://social.technet.microsoft.com/Forums/en-US/e35da253-f0df-41d1-8df2-b73fa54742a0/windows-could-not-start-the-flexnet-licensing-service-service-on-local-computer-error-1068-the?forum=w7itproinstall
Best regards
Michael Shao
TechNet Community Support

Network: Unknown / The dependency service or group failed to start

Hello, MicroSoft tech crew. I know my issue is not something new to you, there are earlier posts with similar to identical problems to mine. For a whole day I tried everything I could find on the internet to fix my issue, but nothing seemed to work.
I cannot connect to the internet. My network and sharing center displays the following, instead of the map:
Unknown
The dependency service or group failed to start.
I am running windows 7 Professional 64-bit.
I used ESET NOD32 as antivirus. I uninstalled it the day this issue appeared.
I have no restore point.
Any other computer or device can successfully connect to my router.
Re-installing a fresh copy of windows is not an option.
These are the solutions I tried and didn't work:
I tried restarting the router (1 minute power-off)
I HAVE reinstalled my drivers for both LAN and WAN network cards at least twice each.
~ I ran the following commands in CMD as administrator over 3 times, successfully, followed by reboot:
* sfc /scannow
* netsh winsock reset // netsh winsock reset catalog
* netsh int ip reset // netsh int ip reset reset.log hit
I have checked the following in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\servicel\NlaSvc has always had full control and read permissions for both SYSTEM and Administrators.
I replaced my nlasvc.dll file from C:\Windows\System32\ with one from another computer (and set TrustedInstaller as its owner)
Booting in Safe mode with networking does not change this situation.
These are some of my services. Note that I turned some of those from Manual to Automatic.
1) COM+ Event System
* Automatic, Started
2) Computer browser
* Automatic, Started
3) DHCP Client
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the DHCP Client Service on Local Computer."
"Error 1186: Element not found."
* Dependencies:
3.1) Network Store Interface Service
* Automatic, Started
4) DNS Client
* Automatic, started
5) Network Connections
* Automatic, Started
6) Network Location Awareness
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Network Location Awareness service on Local Computer."
"Error 1068: The dependency service or group failed to start"
* Dependencies:
6.1) Network Store Interface Service
* Automatic, Started
6.2) Remote Procedure Call (and all it depends on)
* Automatic, Started
7) Remote Procedure Call (RPC)
* As stated above: Automatic, Started
8) Server
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Server service on Local Computer."
"Error 50: The request is not supported."
* Dependencies:
8.1) Security Accounts Manager (and the RPC)
* Automatic, Started
9) TCP/IP Netbios helper
* Automatic, Started
10) Wireless Zero Configuration (XP)
* Nonexistent
11) WLAN AutoConfig
* Automatic, Started
12) Workstation
* Automatic, Started
Also, my ipconfig /all looks very strange. I am not allowed to post pictures yet, but this is the image on skydrive server:
/#cid=2168FA597AC0EAF1&id=2168FA597AC0EAF1%21107

I follow your solution and found the
Network Location Awareness service
could not start.
Then I found the solution from:
http://mjmcfalls.wordpress.com/2012/04/07/network-location-awareness-service-terminated-with-service-specific-error-1073741288/
by running the commands:
net localgroup administrators localservice /add
net localgroup administrators networkservice /add
to add the "Localservice" user and "NetworkService" user
to the adminstrators group.
And the problem solved after reboot.

Sales Quote and Sales Order for Service Module.

Hi All,
I have a scenario with one of the customer where they have a Service Department. The customer is into installation and servicing of Air conditioning systems.
The scenario is as mentioned below:
Customer does the installation of Air Conditioning work and then provides service to the same, if contract mentioned that service is also to be provided by same team. There are also times when the customer quotes only for Servicing of the Air Conditioning in the Projects where the installation is not done by them, but a third party. In such case the customer sends his Sales Quotation for taking up the Servicing of the Air Conditioning (AMC for a year), to be provided to the principle client. If he wins the opportunity then the same will be transferred to Sales Order.
Now in SAP Business One the Service Module starts only with Service Contract and Service Warranty Templates. This is considering that the equipments are delivered by the Contractor him self. This scenario is fine.
But for equipments which are not delivered by the customer, then manual Customer Equipment Card can be prepared and then service contract created to it. But here there is a disconnect between the Quotation that they send to principle and attaching the Sales Order, if the Service Bid is won by Customer. If i need to keep a reference as to which Sales Order was received by Customer from Principle in Service Contract, there is no provision for same.
Is there any way i can do it other than creating a UDF and linking the sales order number to Service Contract and not developing any screens for same?
Require all your valuable inputs..
Regards
Rohan S. Kamble

Hi Rohan........
There is no such standard field in Service Contract to attach Sales Order. You can create UDF else you can have FMS and map it to remark field.
And when you copy it to service call you can attach the same SO at Activity level or it will be attached automatically as yiu are defining it into the service contract.........
Regards,
Rahul

CUE "Service Module is failed"

Similar Messages

Maybe you are looking for