CUOM error when trying to poll performance data from IPCC Express

Hi Network Professionals,
Using CUOM 2.1 SP1 I get an error when trying to access the Performance menu for a IPCC Express Server in the Service Level View.
Error Message:
Performance polling is not supported for the current capability.
The server is fully monitored and I get enviroment, system, interface and application information.
I the Polling Parameters menu (Voice Utilization Settings) the only parameter listed is "Communication Manager and Registred MGCP Gateway Utilization".
The IPCC Express version is 5.0.(2)SR01_Build045.
Is anything missing on the IPCC server? I have only configured it with SNMP.
Kind Regards
Johnny Olsen

hi teresa.
well I bother you because I have a problem similar to that raised earlier, I have a vm INTAL CUOM 2.1 SP1 and the problem is that computers add-in-law his administration IPCC view the service level ... but when I fall into a custom group created the group and add the teams the same ip ipcc already visible, in my group I want to generate displays custom cloud but do not show me the equipment, except that I want to add IVR servers and I do not under any circumstances the samples .. lso probe and reset everything and anything related services, install the SP! and nothing. Can you help me with this or if I recommend CUOM up version of the 2.3 that I could not even see the difference with 2.1 CUOM thanks greetings

Similar Messages

Error when trying to view siebel data from BI Publisher

Hi,
I am trying to view Siebel data in BI publisher via a web service (webservice definition is set to complex in BIP) but when I try to do this I receive the message 'Requested data type does not match with existing data type'.
I am using version 10.1.3.3 of BI Publisher and 8.1.1.2 of Siebel E Clinical.

hi teresa.
well I bother you because I have a problem similar to that raised earlier, I have a vm INTAL CUOM 2.1 SP1 and the problem is that computers add-in-law his administration IPCC view the service level ... but when I fall into a custom group created the group and add the teams the same ip ipcc already visible, in my group I want to generate displays custom cloud but do not show me the equipment, except that I want to add IVR servers and I do not under any circumstances the samples .. lso probe and reset everything and anything related services, install the SP! and nothing. Can you help me with this or if I recommend CUOM up version of the 2.3 that I could not even see the difference with 2.1 CUOM thanks greetings

There is an error when trying to upgrade to Mavericks from OX Lion

There is an error when trying to upgrade to Mavericks from OX Lion

So whenever i click on "free upgrade" ..that message shows up next to it..

Getting a 1809 error when trying to remote control PC from the Console.

This is message i get when trying to remote view or remote control PC.....
1809: An error has occurred while generating a session key for
encryption.The remote session cannot be initiated. Contact Novell
Techical Services and specify this code.

This is for a 1807 error. My error is and 1809 error. Is there somewhere
else to research on a 1809 error when trying to remote control PC from
the Console?
> Perhaps.................
>
> http://support.novell.com/techcenter/search/search.do?
cmd=displayKC&docType=kc&externalId=10094808html&s liceId=&dialogID=2356487
>
> --
> Craig Wilson
> Novell Product Support Forum Sysop
> Master CNE, MCSE 2003, CCNA
>
> Editor - http://www.ithowto.com
>
> (Seeking Full-Time Expert? Drop me a note :> )
> <[email protected]> wrote in message
> news:09i_e.2044$[email protected]..
> > This is message i get when trying to remote view or remote control
PC.....
> >
> >
> > 1809: An error has occurred while generating a session key for
> > encryption.The remote session cannot be initiated. Contact Novell
> > Techical Services and specify this code.
>
>

Error When trying to load master data 0material

Hi,
I got the following error when trying to laod 0MATERIAL master data
"value '000000000004343434 ' for characteristic 0MATERIAL is in external format "
"0MATERIAL : Data record 1 ('000000000004343434 '): Version '000000000004343434 ' is not valid
Can anybody help me in resolving this issue.
Regards

Hi,
Run transaction OMSL.
Create an entry for MATCONV in the overview screen.
Double click on this line and set the length parameter for MATCONV.
the same transaction exists in the r/3 OLTP system compare the 2 systems to set the right values in the details screen in BW.
Hope this helps
Provide points if it does.
Regards
Lalan

Error when trying to configure Manage Data Refresh

Hello,
I recieve the following error when clicking on the "Manage Data Refresh" button:
" Cannot make a cache safe URL for filename "1037/styles/powerpivot.css", file not found. Please check the file in the layout library".
I'll really appreciate any help
thanks,
Eron.

Hi Eron,
We can get PowerPivot Configuration tool if we install SQL Server PowerPivot for SharePoint successfully. Have you following the steps to configure the PowerPivot for SharePoint environment in the article below?
Install PowerPivot for SharePoint:
http://technet.microsoft.com/en-us/library/ee210708.aspx
Furthermore, PowerPivot for SharePoint must be configured before it can be used. After you install PowerPivot for SharePoint using SQL Server Setup, you can configure it using any of the following approaches:
PowerPivot Configuration Tool or PowerPivot for SharePoint 2013 Configuration tool
SharePoint Central Administration
PowerShell cmdlets
Please take a look at the following article:
http://technet.microsoft.com/en-us/library/ee210708.aspx
Regards,
Elvis Long
TechNet Community Support

Getting an error when tried to access task form from worklist app

Hi All,
I am using 10.1.3.4 BPEL PM. I have created a bpel process with a human task.
From the worklist application, when the approver clicks on: Task Id (ideally it should open task form).
In my case, I am getting an error:
Error while inoking URL to display the content. Error while invoking URL. http://bluejays.appsassociates.com:7780/default/EditPayloadPOC1/v2009_05_21__82618/EditPayloadPOC1/EditPayloadPOC1.jsp Check the underlying exception and correct the error. Contact oracle support if error is not fixable..
If you need more information, please check with your administrator with the following exception-identifier: "2009/05/21_12:16:43:777_oc4jadmin"
It works fine in SOA suite 10.1.3.1. and does not work in BPEL PM 10.1.3.4
The only difference is I deployed in 10.1.3.1 using Ant script of bpel project and in 10.1.3.4 I deployed using the BPEL Console itself by browsing the project jar(Since I am getting error when tried to deploy it using Ant).
Is it a known bug or am I making anything wrong. Tried with both Autogeneration and Custom form
I followed: http://download.oracle.com/docs/cd/E11036_01/integrate.1013/b28981/workflow.htm#BABCBAEI
Thanks
Sakrishna Panuganti

Hi does your bpel process has more than one human tasks, e.g., HumanTask1, HumanTask2, HumanTask3...then pl. check and manually fix this below ...e.g.,
check for all of the human tasks workflow contexts tasks forms for dynamic pointers for
domain_id, process_id, process_version.
edit public_html/HumanTask1/form/ear/META-INF/application.xml
<web-uri>workflowform.war</web-uri>
<conteit-root>/${domain_id}/${process_id}/${process_revision}/HumanTask1</context-root>
edit public_html/HumanTask2/form/ear/META-INF/application.xml
<web-uri>workflowform.war</web-uri>
<conteit-root>/${domain_id}/${process_id}/${process_revision}/HumanTask2</context-root>
edit vi public_html/HumanTask3/form/ear/META-INF/application.xml
<web-uri>workflowform.war</web-uri>
<conteit-root>/${domain_id}/${process_id}/${process_revision}/HumanTask3</context-root>
and deploy the process again via jdeveloper or preferably via ant script and try, it worked just fine for us.

Error when trying to delete a vendor from SC

Hi all,
I am encountering a problem when trying to delete a vendor from a contract and assign preferred vendor.
The messages are
"Enter exactly one partner of type preferred vendor"
"Partner data couldnot be determined".
In BBP_PD, I find two entries in partner table with partner_fct = 39.
I am also not able to delete one of this entry.
Please suggest.
Thanks
Nandalal

Hi Nandlal,
Can you see the business partner nos correctly for the vendors you are trying to assign?
Are these vendors assigned to pur org?
DO you get all greens in BBP_BP_OM_INTEGRATE?
BR
Dinesh

Error when trying to enter time data for hourly employees using CAT2

Hi Experts!
I'm trying to enter time data for an absence type using CAT2 for hourly employees and it's giving me an error saying "for attendance type, function or/and one of the URA is required".
I'm not sure what that means, the system has no functions available. Entering time data for full-time salaried employees is working just fine.
Any insight would be greatly appreciated!
Thanks.

hI,
Firstly check infotype 0315
In that check sender cost centre
Next chek whether the Attendent / Absende Tyep which you are trying to enter is configured
That meas it should pop up (F4) when u try to enter using CAT2
in the Attnendence /Abence field
REWARD POINTS

AS91 - AA660 Error when trying to post transaction data

Hi,
     I am getting error AA660 when migrating assets with transactions data.
     I am trying to post Acq Tx 331 (say £1000) along with Unplanned Depreciation Tx 640 (say -£80).
     The error implies that I have a negative NBV in all depreciation areas, even though the NBV is positive (i.e. £1000-£80).
     I can circumvent the problem by setting the Negative Val Flag in each Depreciation Area for the asset, but I have a big volume of assets and this should not be happening.
    Can anyone help?
Regards
Derek

Check the following notes
1) Note 723399 - Invest. support deprec./reval. area: Field XNEGA copied
2) Note 1025126 - Correct error messages from new depreciation calculation
thanks
G. Lakshmipathi

Error -1967390704 when trying to read historical data from CITADEL

I am trying to read historical data for 8 tags in a 'for loop'. If I run the historical vi while my data collection vi is running, I get the error -1967390704 CIT_ReadTrace.vi error code 0x8abc010. I have installed the DSC6.1 fixes and also updated the logos version to 4.4. Is it generally a good practice to not access historical data while new data could still be written to CITADEL?? Is there a vi or anything that could check the versions of all the installed NI software to the latest versions that are available??

I had some major problems when I installed the latest updates. I unzipped to the wrong directory and had multiple copies of some labview files. It really made for some strange operation. Right now I am running labview 6.1 with feb26,2003 updates from the web, logos version 4.4.0.17. It sounds like your database may be corrupted. They also sent me a file to workaround a read issue with the historical vi's.
Attachments:
BenchReadHistTrend.llb ‏104 KB

List of values failure error when trying to use dynamic data values

Hi there,
I have a user who is experiencing problems when trying to use dynamic values in a report. Whenever he tries to insert dynamic parameters he gets the following error message:
Prompting failed with the following message: 'List of Values failure: Failed to get values. [Cause of error: Access is denied.] Error Source: prompt.dll Error Code: 0x8004380D
He even opened the sample report - prompting.rpt - that is included with CR and gets the same error.
We are using Crystal Reports XI Release 2 ver. 11.5.11.1470.
Any help would be appreciated.

Please excuse my ignorance of the product. I've had this problem dropped in my lap and I know practically nothing about Crystal Reports. In doing some digging it appears to me as if the BusinessObjects Enterprise software may not be installed properly, if at all. In the programs menu under the BusinessObjects XI Release 2 folder I see a BusinessObjects Enterprise folder, but the only icon listed in that folder is Software Inventory Tool.
Is the BusinessObjects Enterprise software a separate install from Crystal Reports or is it bundled together? I talked with the tech that did the install and he said that all he had was the Crystal Reports install media.

VISA error when trying to read hex data over serial port

Hi - Sorry about this. I am posting this question as a new thread as I am still having serious problems and may be able to shed more light now.
Basically I am trying to read data formatted as a string of comma separated hexadecimal words over the serial link.
The data is formatted thus: <first word>, <second word>, <third word> etc.... <last word, <CR> where <CR> is a carriage return.
Where each word represents a number, e.g. AB01 is 43777 in decimal.
Now the VI is stalling at VISA close (I attach VI again to this message), the string data is read across by the VI but it will not then close the link unless I remove to USB cable from the comms port. When I run the device in hyperterminal I do not have this problem. The data sting comes back fine (when I send out the command message), the carriage return is recognized as the end of the data message and the comma channel is cleared and ready to accept the next command message.
LabVIEW is then not happy. I don't know why but it could be that the amount of data the demo device I have is sending back is more than the NI-VISA can cope with. Am I correct in thinking 13kbytes is the maximum. If this were the case This would account for my problem. It seems that the number of bytes read by the VI is consistently 12999.
Hope someone can help or this information will at least be useful to somebody so they don't have this problem.
Many Thanks
Ashley.

Yes there is. If your data contains data from 0x00 to 0xFF then you have to disable the 'termination char' in the VISA configure function. The boolean input at the top. Set it to false. Otherwise your transmission will stop at 0x0A by default. You can also tell what the termination character should be, if you want.
btw. Still no VI attached.
Sorry replied to the wrong message. No I did not where are both replying at the same time
Message Edited by K C on 12-08-2005 12:44 PM
Message Edited by K C on 12-08-2005 12:46 PM

I'm getting a 'The Management Pack element is not declared' error when trying to import CSV data into my *extended* WindowsComputer class

Background:
I have a class called SUS_WindowsComputerMP, that is an extension of the Microsoft class, Microsoft.Windows.Computer
I'm trying to import CSV data into this extended class and to the base class as well.
Question:
What am I doing wrong? I have a feeling that the Import CSV Format file is different for importing data into *extended* classes like mine, because the XML structure below would work for non-extended classes.
"...Creating new CSVImporter
Data Filename: D:\Peter\CMDB II\Exported MPs\TestMPs\SUS_WindowsComputer.csv
Format Filename: D:\Peter\CMDB II\Exported MPs\SUS_WindowsComputerMP.xml
Validating against XSD schema...
The 'ManagementPack' element is not declared.
Validation completed.
Format file D:\Peter\CMDB II\Exported MPs\SUS_WindowsComputerMP.xml contains an invalid root element. Expected: root node with name \"CSVImportFormat\"
Could not initialize a Management Object Creator from format file D:\Peter\CMDB II\Exported MPs\SUS_WindowsComputerMP.xml. Import thread exiting.
My import format XML is this:
<CSVImportFormat>
<Class Type="ClassExtension_a3ae3e0f_d578_43dc_aa3e_9037a094763c" >
<Property ID="WindowsServerID" />
<Property ID="PrincipalName" />
<Property ID="NetbiosComputerName" />
<Property ID="IPAddress" />
<Property ID="NetbiosDomainName" />
<Property ID="DNSName" />
<Property ID="OSVersionDisplayName" />
<Property ID="SerialNo" />
<Property ID="ServerDescription" />
<Property ID="AssetTagNo" />
<Property ID="ServerNameRow" />
<Property ID="ChassisType" />
<Property ID="InstallDate" />
<Property ID="IsVirtualMachine" />
<Property ID="BusinessUnitCustomersEnum" />
<Property ID="RegionLocationEnum" />
<Property ID="OtherFunctionRoleEnum" />
<Property ID="ProductTypeEnum" />
<Property ID="ObjectStatus" />
<Property ID="AssetStatus" />
<Property ID="CriticalityEnum" />
<Property ID="EnvironmentEnum" />
<Property ID="CostCodeClassEnum" />
<Property ID="DataClassificationEnum" />
<Property ID="Manufacturer" />
</Class>
</CSVImportFormat>

Hello,
Can anyone please help me out with this weird issue.
thanks,
orton

Error when running package to load data from InfoProvider

I encounter the following error when using the standard package to load data from a InfoProvider to BPC. I tried loading the data from both DSO and InfoCube, but I get the same error.
The log message where the error occurs is as follows:
Task name CLEAR CUBE DATA:
Could not perform write (INHERITED ERROR)
The "convert" step of the process chain completed successfully. This error is happening when the "clear cube according data" step of the process chain gets executed.
Any ideas on why this is happening?
Thanks.

Hi Laeral:
You should be able to just open one VISA session then write and read both commands then close the session at the end. This sounds to me like an error that comes from trying to open two VISA sessions to the instrument at the same time. I have attached some very basic LabVIEW VISA code that writes and reads two different commands. Hopefully it will get you started.
Regards,
Emilie S.
Applications Engineer
National Instruments
Attachments:
Basic VISA Example Two Commands.vi ‏39 KB

CUOM error when trying to poll performance data from IPCC Express

Similar Messages

Maybe you are looking for