CUPC video call issue

Hi there,
i am facing the issue ,CUPC 8.5 video call is not working ..i have cucm 8.0. and CUP 8.0 ..any help will be higly appreciated..
Thanks
Shib

Hey Shib,
For CUPC Desk Phone Troubleshooting, assuming both end points are Personal Communicator Clients, follow the below steps:
1) CAST Issue
For both End Points, make sure that the CAST shows connected under CUPC -> Help -> Show Server Health -> Desk Phone Video Section
The phone must be connected to the computer on which Cisco Unified Personal Communicator is running by Ethernet cable.
2) Firmware Issue
If the end users are controlling 79xx, make sure that the firmware is 9.2(3) or higher. If you are running SCCP9-2-1S, then you will run in the Defect: CSCtq48538 Phone does not send CallStateMessage through CAST connection to PC and have to upgrade the firmware to 9.2(3)
3) Roles and Permissions
Besides the Standard CTI Enabled and Standard CCM End User, if the end users are controlling 99xx or 88xx, then make sure they also have these additional Roles and Permissions
Standard CTI Allow Control of Phones supporting Connected Xfer and conf
Standard CTI Allow Control of Phones supporting Rollover Mode
4) Video Enabled
This setting should be enabled by default, however, make sure that under the Device Configuration Page (CCM Admin -> Device -> Phone -> Affected User's Device
The PC Port and Video Capabilities fields must be enabled for the phone in Cisco Unified Communications Manager.
Now if after verifying all of the above configuration the video call fails then I suggest testing CUPC Soft Phone Video by changing to Soft Phone Mode on both the End Points (You can only change to soft phone mode, if you have the Client Services Framework Device deployed for the end users). If that fails as well, I suggest to engage Cisco Tac for further troubleshooting as we would then need to collect the following:
Clean Detailed PRT from CUPC on both End Points
Detailed CCM and CTI Traces from Call Manager
Calling and Called Party Info
Best Regards,
Jas

Similar Messages

Lync 2013 Mobility Client - Video Call Issue (Everything Else works).

Hey Technet’ies,
I have been struggling for a couple of weeks now to resolve one of the final issues with a Migration/Upgrade Project on Lync Server 2013.
I have nearly every Lync Client Scenario working well except the Mobility Client (outside of the domain) which cannot successfully complete a Video
Call to a Windows Desktop Client (inside the domain) – the toast pops up, but when we click accept - it just times out after 15 seconds
K
The strange thing is every other Video Call scenario works;
Mobility Client (Outside Domain)
àWindows Desktop Client (Inside Domain)
= Unsuccessful
Mobility Client (Inside Domain)
à Windows Desktop Client (Inside Domain) = Successful
Mobility Client (Inside Domain)
à Windows Desktop Client (Outside Domain) = Successful
Mobility Client (Outside Domain)
à Windows Desktop Client (Outside Domain) = Successful
Mobility Client (Inside Domain)
à Mac Desktop Client (Inside Domain) = Successful
Mobility Client (Inside Domain)
à Mac Desktop Client (Outside Domain) = Successful
Mobility Client (Outside Domain)
à Mac Desktop Client (Outside Domain) = Successful
Mobility Client (Outside Domain)
à Mac Desktop Client (Inside Domain) = Successful
Mobility Client (All Scenarios)
à Mobility Client (All Scenarios) = Successful
Our setup is pretty standard;
All OS servers are Win Server 2012 R2
Lync 2013 Standard FE Server
Lync 2013 Edge Server
Reverse Proxy IIS AAR (Also Win Server 20012 R2)
Lync 2013 Desktop Clients, Lync 2011 Mac Clients, IOS and Android Mobility Clients – all latest versions.
External NAT (via Cisco Routers ACL’s)
Internal Windows Firewall Currently off on all Servers
All Certs / DNS Configured as per Technet Recommendation
I have reviewed / analysed a number of log/trace files – looking for some/any information on the problem;
Mobility Client (cmlogX.log)
Windows Desktop Client (*.etl) / Microsoft Message Analyzer
Lync 2013 Server (CSController)
With all my looking I could not make out an error except a timeout (15 seconds) on the Mobility Client log (which I currently can’t find).
Clearly we are missing something and I have gone up and down our implementation a number of times, the only semi-unknown is our old 2010 Pool / Central Management Server (which is currently pretty much redundant but the majority of users still on).
I would really appreciate any feedback anyone can provide or any insight anyone may have on this challenge.
Thanks in advance, Alex.
Alex

Hi Andrew,
Thanks for the quick contact!!
Sorry - typo in my post, I have now corrected it;
Mobility
Client (Outside Domain) àWindows
Desktop Client (Inside Domain) = Unsuccessful
So I completely missed that blog post of yours (out of the 100's I have read) and you are the first person to clearly say (in simple terms) to point the lyncweb.contso.com to the public IP address on my internal DNS, I have just made that change and see
if it will correct the issue - will wait for replication.
Also I am running IIS / AAR as Reverse Proxy (not ISA) and had the Internal DNS Host A of lyncweb.contso.com and lyncdiscover.contso.com point back to my Reverse Proxy Internal NIC (i.e. 10.1.1.32) as the External NIC is isolated on in the Perimeter Network,
is this correct?
So it now goes like this
*Inside Domain*
lyncdiscover.contson.com --> 10.1.1.32 (Reverse Proxy Internal Nic) --> 10.1.1.26 (Front End Server)
lyncweb.contson.com --> 201.183.0.1 (Reverse Proxy External Nic - Public IP) --> 10.1.2.16 (Reverse Proxy External Nic) --> 10.1.1.26 (Front End Server)
Does this make any sense, I know ISA and IIS/AAR are pretty much interchangeable.
Thanks again Andrew and look forward to any feedback,
Alex.
Alex

Lenova K3 Note 3G video call issues

I had Purchased Lenova K3 Note on 22.07.2015 Video Call Option Not found in Calls log Unable to make video calls by 3G Idea Cellular network or Skype & other app downloaded.unable access Mobile banking to login please resolve issues at earliest.

Are you having problems connecting to all wifi's or just this one? If just this one, you could try updating the router fimware.
Your Lumia supports video calling using Skype.

PC-to-Mac video calling issues

Why is it that PC users can see me but I can't see them when using Skype? Is there something I need to download? I have an iMac OS X 10.6.2. Please somebody help me!!!

I assume you have a webcam ? (Just checking!)
Run the Skype setup which includes a little window that shows the video working as a test. If you can be sen there you should be okay.
Also, ask the person you are calling if on their status window, if there is a small camera next to your name indicating you have a webcam available. If it isn't there, it suggest that your system is not making the webcam available.

CUPC 8.6.1 Video Call In Deskphone mode

Hi,
We have Presence Server 8.5 and CUCM 8.0 in network.
CUPC 8.6.1 is installed on user laptop and CIsco 7942 phone is configured for user. User laptop also has camera.
User is able to make video calls using CUPC in softphone mode.
However user is unable to make video call using CUPC in deskphone mode. The video call option on CUPC in deskphone mode remains grey and cannot be selected. What can be reason for this?
Please help to resolve this issue.
Regards,
Andy

Hi,
In CUPC server health it is showing error in Video Desk phone - as CDP uable to detect IP Phone.
However my phone is directly connected to laptop.
how to resolve this issue?
Regards,
Andy

Has anybody found a fix to Facebook video calling in Mavericks, or am I being a moron over the whole issue?

I'm having, and have for a while now, since installing Mavericks had a issue with using video calling for Mavericks. Even though the video icon for video calling is availible in safari, Firefox etc the java app will not download and install. I know there were issues with this initially but have they been resolved? It is doing my proverbial head in, I've searched forums looked at my library playlists etc etc etc, but a fix has evaded me. please please please please somebody give asome sort of affirmitive answer one way or another as to: 1. can it be fixed or 2. will it be fixed!!!!!!!!!

Hi Jerry,
thanks ....
I've just sussed an action .... after I wrote out my own question, I started thinking about it in a different way, the 300 dpi secondary issue was just a niggle after all .... I was coming back to close this question as solved .... I went back to the initial re-size / action logic
Thanks for you help, your answer was spot on, the erroneous results that I was getting earlier were just frustrating ....
action screen-shot attached .... the 2nd step independently from the 1st seemed to answer both height and resolution requirements ....
Gary

Unable to place video calls using CUPC or the IP hardphones.

Hi,
We have installed CUVA 2.1.1 software and the VT-II camera installed perfectly fine.CUCM version 6.0 and Presence 6.0.1
Also get the camera Icon on the IP hard phones as well.But unable to place video calls video calls both with CUPC clients and IP hard phones locally on LAN.
Able to launch and see the local and remote image as same on my own system.
Any thing else that I would need to check or missed out any checklist ????
Regards,
Shams

Hi CJ,
Thanks for the info actually the problem is locally I am not able to place video calls.
When I click on the video check option both the local and remote image are the same as the local image.
Please suggest for placing local video calls within a single cluster what all needs to be checked.
Here we are trying to place video calls IP hard phone to IP hard phone,CUPC to CUPC ,
IPC to IPc.
Regards,
Shams

Facebook video calling freezing issue!

When I start a video call on facebook with Google chrome or Safari I experince this issue:
After starting a video call and the other person accepts the call and it starts to load, then once the person is conneted I see a small screen with my webcam's view at the top right corner of my browser but the issue is the big screen also has a frozen view of my webcam (a photo of me when I first got connected to the call) and the other person can see/hear mebut I'm only able to hear him/her without being able to see them!!!
These are my details:
Macbook Pro - 13-inch, Late 2011
Software: Mac OS X Lion 10.7.5 (11G63)
The diffrent browsers I have tried using are:
1-Google Chrome Version 29.0.1547.76
2- Safari Version 6.0.5 (7536.30.1)
*Ps I have no issue using Skype
please if anyone knows how to solve this reply to the post.
Best Regards,
Khaled

It sounds like it might be a software issue. Check for latest versions of third-party software like chrome, facebook extensions, etc., and either update or uninstall them to test whether the problem remains.
It might also be a problem with network speed or signal quaity. Both ends of a video connection must meet minimum system requirements, so both of you should test with other callers to find which end(s) of the connection has the cause of the problem.
Also click this -> Troubleshooting FaceTime link for other ideas.
Message was edited by: EZ Jim
Mac OSX 10.8.5

3G video call and wifi open network issues

I have bought Lumia 920 few days back. I'm facing some issue with WiFi.when I'm connecting with WiFi open network, connection getting connected but web page is not opening, but in my previous Samsung mobile is getting connected and working ok. I don't know why Lumia 920 only making trouble and also one more thing there no 3G or 4G video calling option in the mobile. So could you please help me regarding this issues.

Are you having problems connecting to all wifi's or just this one? If just this one, you could try updating the router fimware.
Your Lumia supports video calling using Skype.

Skype freezes during video call, no issue with har...

Hi All,
I have recently been set to the task to figure out why everyone around me cannot skype a video call longer than approx. 2mins without the feed freezing, going black, or turning to static.
I have read almost all the forums in the community on video freezing and have tried all listed options.
I have throughly checked all of mine and others laptops hardware for functionality and nothing is wrong.
It is running Windows 8.1 and has all Windows updates, software and firmware updates.
It seems many people are crying for an answer for this and reverting to an old version of Skype is no longer possible.
Ideas??? ***Please do not reply with: reinstall your driver or test your camera to see if it freezes in other programs. This has been done. This is not a computer model/operating system specific issue and I see it as a skype issue.

Try to uninstall the currently installed Skype version and install the previous 6.14.0.104 version using the download links provided here:
http://community.skype.com/t5/Windows-desktop-client/ASUS-USB2-0-Webcam-not-recognized-by-Skype-6-18...
Make sure to disable automatic updates:
Tools -> Options -> Advanced -> Automatic updates ->Turn off automatic updates

Video calls and videos issue

after the 5.1 update, i noticed that videos don't rotate when the phone is held horizontally. also i made a video call and when i rotated the phone the screen became unresponsive and kept going on and off unless when i held the phone in a certain angle which i cant figure out, i dont know if this issue has been there the whole time because the first video call i made on the phone (via skype) was after the update. also when i unlock the screen sometimes the colors fade and become lighter, and the screen itself freezes for 2 seconds.

I see, well if it's due to the update itself you can try to reinstall the 5.1 update with Sony PC Companion and see if the fixes the issue.
http://support.sonymobile.com/us/tools/pc-companion/

Issue with Video Calling

I recently bought a Kindle Fire HD and I downloaded Skype. My boyfriend also has Skype for his Samsung Galaxy Note. Whenever we try to use video calling the audio works fine but we can only see a black screen, unable to see each other and cant even see ourselves on the screen. Has anyone experienced this before? And what did they do to fix it?

its seems that thusand of well informed well knonw I-T specialist have not a answer of some simple questions....
what a joke... skype have huge platform but not single specialist to answer me ..

Does anyone have wi-fi issues after 7.1.1 update. its really killing the quality of video calls.

its really killing the quality of video calls.Facetime and Skype for example. Tried all the tips including resetting networks, rebooting, nothing helpled.

After I updated my iphone 4S to 7.1.1, there is always problem with Facetime and Skype. Wifi just drops for no reason. I have tried everything, resetting the phone and freezing for 10 min, but nothing helped. Hope Apple will fix this bug soon.

Major Security Issue on Android - Incomming video call was automatically received

Hi all, today I encountered a major security bug. My phone was on the table, several meters away from me, facing up. When I walked past it, I saw that I have a video call which was accepted somehow automatically by skype on my mobile phone. It was my friend and he confirmed that he was able to hear and see everything for more than a minute. Is this a known bug? This is something major. Kind regards,GD

Some previous Android skype versions had a severe security bug, see this: http://community.skype.com/t5/Android/Automatical-calls/td-p/3806053 However, it should be gone if you have a somewhat new version; unless a new bug has surfaced.

If the DroidX had a front camera how easy would it be to video call with Skype or Fringe?

Apparently EVO with Sprint you can video conference with Fringe but is this something that has to been done through WIFI? I was ready to upgrade to the DroidX but I am wondering if I should hold off for the front camera. I love using Skype video and it would be amazing to have this feature on the phone if it is an easy thing to do.
It would be greatly appreciated if someone is knowledgable about this information.
Thank you!

Since that is a hypothetical situation (Droid X front camera), there is no real way to even guess how the carrier or manufacture would implement this feature because if you look at how other devices use this feature you notice that they are not implementing this feature the same way. Also in regards to the EVO video calls is across the 4G network but from what I have read they have been experiencing a lot of connection issues do to the network being over whelmed (which isnt a surprise)...

CUPC video call issue

Similar Messages

Maybe you are looking for